PI3303-00-EVAL1

USER GUIDE | UG:302 PI33xx-xx-EVAL1 & PI34xx-xx-EVAL1 ZVS Regulators Buck Evaluation Board Contents Page Introduction 1 Evaluation Board Supply & Load Connections 4 Bills of Materials 7 Evaluation Board Notes 13 Introduction The PI33xx-xx-EVAL1 and PI34xx-xx-EVAL1 evaluation board demonstrates the features and benefits of the ZVS Buck Regulator PI33xx and PI34xx families. The board features the ZVS Buck Regulator SiP, along with inductor, ceramic input and output capacitors. The evaluation board provides several options for making input power (VIN and GND) and output load (VOUT and GND) connections. The user can solder tab style banana jacks or wire, use threaded binding posts secured by a retaining nut, or to simply use a #6 nut and bolt connection. All the I/O pins are labeled and routed to the board edge for easy access. Each I/O pin is accompanied with an adjacent 50mil through-hole for adding a test point or to facilitate wiring to external circuitry. The board has a scope tip jack for measuring output voltage (VOUT ), and has locations for two optional jacks for measuring VIN and the switching node of the regulator (See Figure 4). There are two headers installed: an ENABLE jumper which can be used to enable or disable the converter and the remote sense jumper that will connect the buck’s remote sense pin to the output at the VOUT terminal. Connections required for parallel regulator operation are grouped together (labeled Current Sharing) to allow for easy connection between evaluation boards. There is a zero ohm jumper between SYNCI and SGND to ensure that SYNCI is grounded when not used. This resistor must be removed for interleaved operation. Please refer to the product data sheet for more detailed information on paralleling and on interleaving units. There are two unpopulated resistor footprints (RADJ1 and RADJ2) used in trimming the output voltage and a capacitor footprint (CTRK) to add additional capacitance to the output tracking pin. Please refer to the product datasheet for more detailed information on these topics. The evaluation board is constructed using 4 layers of 2oz copper and is routed to optimize the regulation path between input and output voltage, which reduces the parasitic losses and yields the best efficiency. UG:302 Page 1 Table 1 Applicable evaluation board, product part numbers, and associated evaluation PCB number Product Part Number Evaluation Board Number PCB Part Number PI3301-00-LGIZ PI3301-00-EVAL1 PCB0108 PI3301-01-LGIZ PI3301-01-EVAL1 PCB0113 PI3302-00-LGIZ PI3302-00-EVAL1 PCB0108 PI3302-03-LGIZ PI3302-03-EVAL1 PCB0190 PI3303-00-LGIZ PI3303-00-EVAL1 PCB0108 PI3305-00-LGIZ PI3305-00-EVAL1 PCB0108 PI3423-00-LGIZ PI3423-00-EVAL1 PCB0113 PI3424-00-LGIZ PI3424-00-EVAL1 PCB0113 End of Life Product Part Number End of Life Evaluation Board Number PCB Part Number PI3303-20-LGIZ PI3303-20-EVAL1 PCB0108 PI3311-00-LGIZ PI3311-00-EVAL1 PCB0113 PI3311-01-LGIZ PI3311-01-EVAL1 PCB0113 PI3312-00-LGIZ PI3312-00-EVAL1 PCB0108 PI3312-01-LGIZ PI3312-01-EVAL1 PCB0113 PI3318-00-LGIZ PI3318-00-EVAL1 PCB0113 PI3318-01-LGIZ PI3318-01-EVAL1 PCB0113 PI3420-00-LGIZ PI3420-00-EVAL1 PCB0113 PI3421-00-LGIZ PI3421-00-EVAL1 PCB0113 PI3422-00-LGIZ PI3422-00-EVAL1 PCB0113 Figure 1 Evaluation board (PCB 0108) UG:302 Page 2 Figure 2 Evaluation board (PCB 0113) Figure 3 Evaluation board (PCB 0190) UG:302 Page 3 Evaluation Board Supply & Load Connections Figure 4 displays the recommended connections for input supply and output loading, and the best test points for measuring input and output voltages. All the I/O pins are brought out to the edge to allow for easy measurement and/or connection to the user’s external circuitry. Figure 4 Evaluation board measurement connection UG:302 Page 4 Figure 5 Evaluation board (PCB 0108) schematic JJVOUT JJSW JJVIN L1 C1 VIN C2 C3 C4 C5 C6 C7 C8 VIN VS1 C10 C11 C12 C13 C14 C15 C16 VOUT ZVS Buck PGND SYNCO SYNCI REM ADJ EAO TRK PWRGD 1 2 3 4 SCL SDA EN ENABLE PGND VOUT ADR0 ADR1 RADJ1 H1 Remote Sense Jumper RSYNC 0 ohm PGND SGND RADJ2 SGND SYNCO SYNCI SCL SDA EN CTRK ADR0 ADR1 PWRGD TRK EAO ADJ REM Figure 6 Evaluation board (PCB0113) schematic JJVOUT JJSW JJVIN L1 C1 VIN C2 C3 C4 C5 C6 C7 C8 VIN C10 C11 C12 C13 C15 C16 C17 C18 VS1 ZVS Buck PGND REM ADJ EAO TRK PWRGD/PGD SCL SDA 1 2 3 4 PGND VOUT SYNCO SYNCI EN ENABLE ADR0 ADR1 RADJ1 H1 Remote Sense Jumper RSYNC 0 ohm PGND SGND RADJ2 SGND VOUT SYNCO SYNCI SCL SDA EN CTRK ADR0 ADR1 PWRGD UG:302 TRK EAO ADJ REM Page 5 Figure 7 Evaluation board (PCB0190) schematic JJSW JJVIN C1 VIN C2 C3 C4 C5 C6 C7 C8 JJVOUT L1 VIN VS1 C10 C11 C12 C13 C14 C15 ZVS Buck PGND REM ADJ EAO TRK PWRGD SCL SDA 1 2 3 4 PGND VOUT SYNCO SYNCI EN ENABLE ADR0 ADR1 RADJ1 H1 Remote Sense Jumper RSYNC 0 ohm PGND SGND RADJ2 SGND VOUT SYNCO SYNCI SCL SDA EN CTRK ADR0 ADR1 PWRGD TRK EAO ADJ REM UG:302 Page 6 Bills of Materials Locate the PCB number for your product in the following tables and find the BOM for that PCB. Table 2 Bill of materials Vicor ZVS Buck Regulator evaluation board (PCB 0108) Device PI3301-00 Qty Designators Manufacturer Part Number U1 3.3V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3301-00-LGIZ 4 C10-C13 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L L1 200nH Buck Inductor Eaton FPT705-200-R I2C_ INTERFACE n/a n/a n/a n/a 1 U1 5V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3302-00-LGIZ 4 C10-C13 47µF 10V Ceramic Output Capacitor Murata GRM31CR61A476ME15L 1 PI3303-00 Description 1 1 PI3302-00 Value L1 200nH Buck Inductor Eaton FPT705-200-R I2C_ INTERFACE n/a n/a n/a n/a 1 U1 12V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3303-00-LGIZ 4 C10-C13 22µF 25V Ceramic Output Capacitor Murata GRM31CR61E226KE15L 1 L1 230nH Buck Inductor Eaton FPT705-200-R I2C_ INTERFACE n/a n/a n/a n/a 1 U1 12V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3303-20-LGIZ 4 C10-C13 22µF 25V Ceramic Output Capacitor Murata GRM31CR61E226KE15L 1 L1 230nH Buck Inductor EatonCoiltronics FPT705-230-R 1 I2C_ INTERFACE 4 Position, I2C Header Molex 22-23-2041 1 U1 15V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3305-00-LGIZ 4 C10-C13 22µF 25V Ceramic Output Capacitor Murata GRM31CR61E226KE15L 1 L1 230nH Buck Inductor EatonCoiltronics FPT705-230-R I2C_ INTERFACE n/a n/a n/a n/a PI3303-20 [a] PI3305-00 [a] End-of-life part number. UG:302 Page 7 Bills of Materials (Cont.) Table 2 (Cont.) Bill of materials Vicor ZVS Buck Regulator evaluation board (PCB 0108) Device Qty Designators Value Description Manufacturer Part Number 1 U1 2.5V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3312-00-LGIZ 4 C10-C13 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 200nH Buck Inductor EatonCoiltronics FPT705-200-R I2C_ INTERFACE n/a n/a n/a n/a SM Test Point Keystone 5015 PI3312-00 [a] Common 10 ADJ, ADR0, ADR1, EAO, EN, REM, SGND, SYNCI, SYNCO, TRK 4 C1-C4 4.7µF 50V Ceramic Capacitor Murata GRM31CR71H475KA12L 4 C5-C8 0.1µF 50V Ceramic Capacitor TDK C2012X7R1H104K085AA 1 C14 0.1µF 50V Ceramic Capacitor Murata GRM319R71H104KA01D 2 C15-C16 1µF 16V Ceramic Capacitor Murata GRM188R71C105KA12J 2 ENABLE, H1 Header Jumper Samtec TSW-148-07-F-S 3 GND, VIN, VOUT TH Testpoint Vector K24 1 JJVOUT Compact 3.5mm Jack Tektronix 131503100 JJVIN, JJVSW [a] 1 PCB 1 RSYNC n/a 0Ω n/a n/a n/a PI33xx-xxEVAL1 PCB VICOR PCB0108 0805 Resistor Rohm MCR10EZPJ000 End-of-life part number. UG:302 Page 8 Bills of Materials (Cont.) Table 3 Bill of materials Vicor ZVS Buck Regulator evaluation board (PCB 0113) Device PI3301-01 PI3311-00 [a] PI3311-01 [a] PI3312-01 [a] PI3318-00 [a] [a] Qty Designators Value Description Manufacturer Part Number 1 U1 3.3V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3301-01-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 150nH Buck Inductor Datatronics 38950-05 6 C1-C6 4.7µF 50V Ceramic Capacitor Murata GRM31CR71H475KA12L 1 U1 1V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3311-00-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 125nH Buck Inductor Datatronics 38950-04 6 C1-C6 4.7µF 50V Ceramic Capacitor Murata GRM31CR71H475KA12L 1 U1 1V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3311-01-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 80nH Buck Inductor Datatronics 38950-02 6 C1-C6 4.7µF 50V Ceramic Capacitor Murata GRM31CR71H475KA12L 1 U1 2.5V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3312-01-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 125nH Buck Inductor Datatronics 38950-04 6 C1-C6 4.7µF 50V Ceramic Capacitor Murata GRM31CR71H475KA12L 1 U1 1.8V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3318-00-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 150nH Buck Inductor Datatronics 38950-05 6 C1-C6 4.7µF 50V Ceramic Capacitor Murata GRM31CR71H475KA12L End-of-life part number. UG:302 Page 9 Bills of Materials (Cont.) Table 3 (Cont.) Bill of materials Vicor ZVS Buck Regulator evaluation board (PCB 0113) Device PI3318-01 [a] PI3420-00 [a] PI3421-00 [a] PI3422-00 [a] PI3423-00 [a] Qty Designators Value Description Manufacturer Part Number 1 U1 1.8V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3318-01-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 125nH Buck Inductor Datatronics 38950-04 6 C1-C6 4.7µF 50V Ceramic Capacitor Murata GRM31CR71H475KA12L 1 U1 1.8V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3420-00-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 80nH Inductor Datatronics 38950-02 6 C1-C6 22µF 25V Ceramic Capacitor Murata GRM31CR61E226KE15L 1 U1 1.8V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3421-00-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 125nH Inductor Datatronics 38950-04 6 C1-C6 22µF 25V Ceramic Capacitor Murata GRM31CR61E226KE15L 1 U1 2.5V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3422-00-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 125nH Inductor Datatronics 38950-04 6 C1-C6 22µF 25V Ceramic Capacitor Murata GRM31CR61E226KE15L 1 U1 3.3V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3423-00-LGIZ 8 C10-C15 C19-C20 100µF 6.3V Ceramic Output Capacitor Murata GRM31CR60J107ME39L 1 L1 150nH Inductor Datatronics 38950-05 6 C1-C6 22µF 25V Ceramic Capacitor Murata GRM31CR61E226KE15L End-of-life part number. UG:302 Page 10 Bills of Materials (Cont.) Table 3 (Cont.) Bill of materials Vicor ZVS Buck Regulator evaluation board (PCB 0113) Device PI3424-00 Common Qty Designators Description Manufacturer Part Number 1 U1 5V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3424-00-LGIZ 8 C10-C15 C19-C20 47µF 10V Ceramic Output Capacitor Murata GRM31CR61A476ME15L 1 L1 150nH Inductor Datatronics 38950-05 22µF 25V Ceramic Capacitor Murata GRM31CR61E226KE15L SM Testpoint Keynote 5015 6 C1-C6 11 ADJ, ADR0, ADR1, EAO, EN, NC, REM, SGND, SYNCI, SYNCO, TRK 2 C7-C8 0.1µF 50V Ceramic Capacitor TDK C2012X7R1H104K085AA 1 C16 0.1µF 50V Ceramic Capacitor Murata GRM319R71H104KA01D 2 C17-C18 1µF 16V Ceramic Capacitor Murata GRM188R71C105KA12J 2 ENABLE, H1 Header Jumper Samtec TSW-148-07-F-S 3 GND, VIN, VOUT TH Testpoint Vector Technologies K24C/M 1 JJVOUT Compact 3.5mm Jack Tektronix 131503100 JJVIN, JJVSW Value n/a n/a n/a n/a PI3xxx-xxEVAL1-pcb VICOR PCB0113 1 PCB 1 ROUT 1kΩ Resistor Rohm MCR18EZHF1001 1 RSYNC 0Ω Resistor Rohm MCR10EZPJ000 I2C_ INTERFACE n/a n/a n/a n/a UG:302 Page 11 Bills of Materials (Cont.) Table 4 Bill of materials Vicor ZVS Buck Regulator evaluation board (PCB 0190) Device PI3302-03 Qty Designators Description Manufacturer Part Number 1 U1 5V ZVS Buck Regulator ZVS Buck Regulator VICOR PI3302-03-LGIZ 6 C10-C15 47µF 10V Ceramic Capacitor Murata GRM32ER71A476KE15L 1 L1 185nH Buck inductor EatonCoiltronics FP1507R1-R185-R 11 ADJ, ADR0, ADR1, EAO, EN, N/C, REM, SGND, SYNCI, SYNCO, TRK SM Testpoint Keystone 5015 1 C16 0.1µF 50V Ceramic Capacitor Murata GRM319R71H104KA01D 2 C17-C18 1µF 16V Ceramic Capacitor Murata GRM188R71C105KA12J 6 C1-C6 10µF 50V Ceramic Capacitor TDK C3216X5R1H106K160AB 2 C7-C8 0.1µF 50V Ceramic Capacitor TDK C2012X7R1H104K085AA 2 ENABLE, H1 Header Jumper Samtec TSW-148-07-F-S n/a n/a n/a TH Testpoint Vector K24 JJVIN, JJVSW, JJVOUT 3 n/a GND, VIN VOUT 1 ROUT 1kΩ 1206 Resistor Rohm MCR18EZHF1001 1 RSYNC 0Ω 0805 Resistor Rohm MCR10EZPJ000 n/a n/a n/a n/a I2C_ INTERFACE Value UG:302 Page 12 Evaluation Board Notes The evaluation board has solder mask openings on the bottom side of the board to allow for the option of additional output capacitance (4 x 1206 or 2 x 1812). There are two additional, unmarked, scope tip test points (circled in red in Figures 8 – 10) that allow the user to measure VIN and the switching node (VS1). These are labeled as JJVIN and JJVSW in Figures 8 – 10. There are two through-hole pads (blue circle) for the addition of an electrolytic bulk storage capacitor. This capacitor is required when the evaluation board is connected to the input voltage source through long leads. A 100µF, 50V Electrolytic is recommended with an ESR between 20 and 50mΩ. The two pins labeled as “N/C” (highlighted in green box in Figures 8 – 10) are not electrically connected to each other. There are internal connections within the PI33xx and PI34xx between grounds SGND and PGND. It is not required to tie these two grounds together externally and these two grounds are not connected together on the evaluation board. UG:302 Page 13 Figure 8 Optional Test Points & Component Locations (PCB 0108) Figure 9 Optional Test Points & Component Locations (PCB0113) Figure 10 Optional Test Points & Component Locations (PCB0190) UG:302 Page 14 Figure 11 Board Dimensions Common to all Three PCBNumbers UG:302 Page 15 Limitation of Warranties Information in this document is believed to be accurate and reliable. HOWEVER, THIS INFORMATION IS PROVIDED “AS IS” AND WITHOUT ANY WARRANTIES, EXPRESSED OR IMPLIED, AS TO THE ACCURACY OR COMPLETENESS OF SUCH INFORMATION. VICOR SHALL HAVE NO LIABILITY FOR THE CONSEQUENCES OF USE OF SUCH INFORMATION. IN NO EVENT SHALL VICOR BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR SAVINGS, BUSINESS INTERRUPTION, COSTS RELATED TO THE REMOVAL OR REPLACEMENT OF ANY PRODUCTS OR REWORK CHARGES). Vicor reserves the right to make changes to information published in this document, at any time and without notice. You should verify that this document and information is current. This document supersedes and replaces all prior versions of this publication. All guidance and content herein are for illustrative purposes only. Vicor makes no representation or warranty that the products and/or services described herein will be suitable for the specified use without further testing or modification. You are responsible for the design and operation of your applications and products using Vicor products, and Vicor accepts no liability for any assistance with applications or customer product design. It is your sole responsibility to determine whether the Vicor product is suitable and fit for your applications and products, and to implement adequate design, testing and operating safeguards for your planned application(s) and use(s). VICOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN LIFE SUPPORT, LIFE-CRITICAL OR SAFETY-CRITICAL SYSTEMS OR EQUIPMENT. VICOR PRODUCTS ARE NOT CERTIFIED TO MEET ISO 13485 FOR USE IN MEDICAL EQUIPMENT NOR ISO/TS16949 FOR USE IN AUTOMOTIVE APPLICATIONS OR OTHER SIMILAR MEDICAL AND AUTOMOTIVE STANDARDS. VICOR DISCLAIMS ANY AND ALL LIABILITY FOR INCLUSION AND/OR USE OF VICOR PRODUCTS IN SUCH EQUIPMENT OR APPLICATIONS AND THEREFORE SUCH INCLUSION AND/OR USE IS AT YOUR OWN RISK. Terms of Sale The purchase and sale of Vicor products is subject to the Vicor Corporation Terms and Conditions of Sale which are available at: (https://www.vicorpower.com/termsconditionswarranty) Export Control This document as well as the item(s) described herein may be subject to export control regulations. Export may require a prior authorization from U.S. export authorities. Contact Us: https://www.vicorpower.com/contact-us Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 www.vicorpower.com email Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com ©2017 – 2022 Vicor Corporation. All rights reserved. The Vicor name is a registered trademark of Vicor Corporation. All other trademarks, product names, logos and brands are property of their respective owners. 07/22 Rev 1.6 Page 16