V28C12H100BG2

Data Sheet 28V Wide Input Micro Family DC-DC Converter Module Features • • • • • • • • • • • DC input range: 9 - 36 V Input surge withstand: 50 V for 100 ms DC output: 3.3 – 48 V Programmable output: 10 to 110% Regulation: ±0.4% no load to full load Efficiency: Up to 81% Maximum operating temp: 100°C, full load Power density: up to 60 W per cubic inch Height above board: 0.43 in. (10,9 mm) Parallelable, with N+M fault tolerance Low noise ZCS / ZVS architecture Shown actual size: 2.28 x 1.45 x 0.5 in 57,9 x 36,8 x 12,7 mm Product Overview These DC-DC converter modules use advanced power processing, control and packaging technologies to provide the performance, flexibility, reliability and cost effectiveness of a mature power component. High frequency ZCS / ZVS switching provides high power density with low noise and high efficiency. Absolute Maximum Ratings Parameter +In to -In voltage PC to -In voltage PR to -In voltage SC to -Out voltage Isolation voltage in to out Rating -0.5 to +53 -0.5 to +7.0 -0.5 to +7.0 -0.5 to +1.5 3000 1500 500 -55 to +100 -65 to +125 500 (260) 750 (390) Mounting torque 5 (0.57) Unit Vdc Vdc Vdc Vdc Vrms Vrms Vrms °C °C °F (°C) °F (°C) in-lbs (N-m) Test voltage Test voltage Test voltage M-Grade M-Grade 100 ms off) No load No load to full load; nominal input Output voltage 95% of nominal Output voltage < 250 mV 0 8.49 5.83 15 Vout, 100 W (e.g. V28C15C100BL) Parameter Efficiency Ripple and noise Output OVP set point Dissipation, standby Load regulation Load current Current limit Short circuit current Min 79 17.1 Typ 80.7 200 17.8 7.1 ±0.02 7.67 7.67 Max 250 18.5 10 ±0.2 6.67 9.01 9.01 Unit % mV Volts Watts % Amps Amps Amps Notes Nominal input; full load; 25°C p-p; Nominal input; full load; 20 MHz bandwith 25°C; recycle input voltage to restart (>100 ms off) No load No load to full load; nominal input Output voltage 95% of nominal Output voltage < 250 mV 0 6.8 4.66 Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 28V Micro Family Rev. 1.2 Page 4 of 11 Set your site on VICOR at vicorpower.com MODULE SPECIFIC OPERATING SPECIFICATIONS (CONT.) 24 Vout, 100 W (e.g. V28C24C100BL) Parameter Efficiency Ripple and noise Output OVP set point Dissipation, standby Load regulation Load current Current limit Short circuit current Min 80.3 27.1 Typ 81.8 180 28.1 5.3 ±0.02 4.8 4.8 Max 225 29.1 6.2 ±0.2 4.17 5.63 5.63 Unit % mV Volts Watts % Amps Amps Amps Notes Nominal input; full load; 25°C p-p; Nominal input; full load; 20 MHz bandwith 25°C; recycle input voltage to restart (>100 ms off) No load No load to full load; nominal input Output voltage 95% of nominal Output voltage 100 ms off) No load No load to full load; nominal input Output voltage 95% of nominal Output voltage < 250 mV 0 3.64 2.49 36 Vout, 100 W (e.g. V28C36C100BL) Parameter Efficiency Ripple and noise Output OVP set point Dissipation, standby Load regulation Load current Current limit Short circuit current Min 79.5 40.4 Typ 80.9 180 41.9 5.8 ±0.02 3.2 3.2 Max 225 43.4 6.2 ±0.2 2.78 3.76 3.76 Unit % mV Volts Watts % Amps Amps Amps Notes Nominal input; full load; 25°C p-p; Nominal input; full load; 20 MHz bandwith 25°C; recycle input voltage to restart (>100 ms off) No load No load to full load; nominal input Output voltage 95% of nominal Output voltage 100 ms off) No load No load to full load; nominal input Output voltage 95% of nominal Output voltage < 250 mV 0 2.12 1.45 Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 28V Micro Family Rev. 1.2 Page 5 of 11 Set your site on VICOR at vicorpower.com CONTROL FUNCTIONS - PC PIN Module Enable/Disable The module may be disabled by pulling PC below 2.3 V with respect to the –Input. This may be done with an open collector transistor, relay, or optocoupler. Multiple converters may be disabled with a single transistor or relay either directly or via “OR’ing” diodes. See Figure 1. Primary Auxiliary Supply At 5.7 V, PC can source up to 1.5 mA. In the example shown in Figure 3, PC powers a module enabled LED. Module Alarm The module contains “watchdog” circuitry which monitors input voltage, operating temperature and internal operating parameters. In the event that any of these parameters are outside of their allowable operating range, the module will shut down and PC will go low. PC will periodically go high and the module will check to see if the fault (as an example, overtemperature) has cleared. If the fault has not been cleared, PC will go low again and the cycle will restart. The SC pin will go low in the event of a fault and return to its normal state after the fault has been cleared. See Figures 2 and 4. +In PC +IN PC PR 1M 5.7 Vdc (0-3 mA) SW1 Auto Restart Input Undervoltage Input Overvoltage [a] Over Temperature Module Faults +OUT 50 Ω 2-20 ms typ. f(VIN) SW2 SW3 1K SC Disable PR –In 6K 1.23 Vdc –IN SW1, 2, & 3 shown in "Fault" position –OUT Disable = PC