351HE0B2ZZ

Model 351 HE Vishay Spectrol Single Turn Bushing Mount Hall Effect Sensor in Size 09 (22.2 mm) FEATURES • Accurate linearity down to: ± 0.5 % • All electrical angles available up to: 360° (no dead band) • Long life: greater than 10M cycles • Non contacting technology: Hall effect • Model dedicated to all applications in harsh environments RoHS COMPLIANT ELECTRICAL SPECIFICATIONS PARAMETER Electrical Angle Linearity Supply Voltage Supply Current Output Signal Over Voltage Protection Reverse Voltage Protection Load Resistance Recommanded Hysteresis STANDARD 90°, 180°, 270°, 360° ±1% 5 VDC ± 10 % 10 mA typical Analog ratiometric 10 % to 90 % of Vsupply or PWM 10 % to 90 % duty cycle + 20 VDC - 10 VDC Min. 1 kΩ for analog output and PWM output < 0.2 % SPECIAL Any other angle upon request ± 0.5 % Other upon request 16 mA for PWM output Other upon request MECHANICAL SPECIFICATIONS PARAMETER Mechanical travel Bearing type Standard Weight 360° continuous, stops upon request: 340° ± 3° Sleeve bearing IP 50; other on request 20 g ± 2 g ORDERING INFORMATION/DESCRIPTION 351HE 0 A 1 W OUTPUT TYPE A OUTPUT SIGNAL 1S22 SHAFT TYPE XXXX SPECIAL REQUEST BO 10 PACKAGING Box of 10 pieces e1 LEAD FINISH ELECTRICAL MODEL FEATURES LINEARITY ANGLE W: Wires 1: 90° 0: Continuous rotation A: ± 1 % Z: Custom 2: 180° and antirotation pin B: ± 0.5 % 3: 270° 1: Continuous rotation 4: 360° and no antirotation 9: Other angles pin 2: Stops at 340° and antirotation pin 3: Stops at 340° and no antirotation pin 0: 6 mm A: Analog CW B: Analog CCW 1: 6.35 mm C: PWM CW 2: 3.175 mm 9: Special D: PWM CCW P: Plain Z: Other output S: Slotted Z: Other type Shaft length from mounting face 22 mm to 72 mm max. per step of 5 mm SAP PART NUMBERING GUIDELINES 351HE MODEL 1 MECHANICAL FEATURES B LINEARITY 9 ELECTRICAL ANGLE Z OUTPUT TYPE C OUTPUT SIGNAL 0P27 SHAFT TYPE XXXX SPECIAL REQUEST www.vishay.com 160 For technical questions, contact: sfer@vishay.com Document Number: 57099 Revision: 15-Nov-07 Model 351 HE Single Turn Bushing Mount Hall Effect Sensor in Size 09 (22.2 mm) VOUT ANALOG Operating Temperature Diagnostic High Level Diagnostic Low Level 85 °C 96 % min. 2 % max. 125 °C 96 % min. 4 % max. Vishay Spectrol Vout (% Vsupply) Diag High Level 90 % Diagnostic High Area Vout (% Vsupply) Diag High Level 90 % Diagnostic High Area CCW CW 10 % Diag Low Level 0 Diagnostic Low Area Theta (Position) 10 % Diag Low Level 0 Diagnostic Low Area Theta (Position) VOUT PWM Vout (% Vsupply) 97 % min. T high CW Duty Cycle = Thigh T T low 1.5 % max. 0 T: periodicity Time (µs) Document Number: 57099 Revision: 15-Nov-07 For technical questions, contact: sfer@vishay.com www.vishay.com 161 Model 351 HE Vishay Spectrol Single Turn Bushing Mount Hall Effect Sensor in Size 09 (22.2 mm) DIAGNOSTIC MODES FAILURE Vout Analog Rpull-up Diagnostic high area Diagnostic high area Diagnostic high area Diagnostic high area Diagnostic high area Vout Analog Rpull-down Diagnostic low area Diagnostic low area Diagnostic low area Diagnostic low area Diagnostic low area Vpull-up Vout PWM Rpull-up = 1 kΩ Vpull-up = Vsupply = 5 V > 97 % Vsupply without modulation > 97 % Vsupply without modulation > 97 % Vsupply without modulation > 97 % Vsupply without modulation > 97 % Vsupply without modulation 1: Broken GND 2: Broken Vout 3: Broken Vsupply Over Voltage Vsupply > 7 V Under Voltage Vsupply < 2.7 V Vsupply 3 Rpull-up Vpull-up can be independent to Vsupply Sensor 2 Vout GND 1 Cut off ENVIRONMENTAL SPECIFICATIONS Vibrations Shocks Operating Temperature Range Life Rotational Speed (max) Immunity to Radiated Electromagnetic Disturbances Immunity to Power Frequency Magnetic Field Radiated Electromagnetic Emissions Electrostatic Discharges Materials Housing Bushing Shaft Output Bushing Mount Hardware Lockwasher Internal Tooth Panel Nut Steel nickel plated Brass nickel plated Thermoplastic housing Brass nickel plated Stainless steel 3 lead wires 20 G from 10 Hz to 2000 Hz 3 shocks/axis; 50 G half a sine 11 ms - 45 °C; + 125 °C > 10M of cycles 120 rpm 200 V/m 150 kHz/1 GHz 200 A/m 50 Hz/60 Hz 30 MHz/1 GHz < 30 dBµV/m Contact discharges: ± 4 kV Air discharges: ± 8 kV www.vishay.com 162 For technical questions, contact: sfer@vishay.com Document Number: 57099 Revision: 15-Nov-07 Model 351 HE Single Turn Bushing Mount Hall Effect Sensor in Size 09 (22.2 mm) DIMENSIONS in millimeters 22 ± 0.8 15.8 ± 0.4 1.07 ± 0.2 (2) 0.4 x 45° Vishay Spectrol Ø 22.7 ± 0.13 Ø 1.57 ± 0.1 (2) 3/8 - 32 UNEF-2A (3) Ø 6.35 -0 0.036 Ø 9.525 VISHAY 0.8 ± 0.2 (1) 8.9 1 ± 0.2 (1) 3 WIRES AWG 20 LENGTH: 300 mm 9.5 YELLOW 7.92 (2) GREEN RED CW OR CCW ACCORDING OUTPUT MODE CHOICE GENERAL TOLERANCE: ± 0.5 mm VI SH AY Vsupply = GREEN WIRE Gnd = YELLOW WIRE Vout = RED WIRE VIEWED FROM SHAFT Notes: (1) For version slotted shaft (2) For version non turn pin (3) For shaft type “1“ MARKING Unit Identification Manufacturer’s name and complete sap part reference, date code, and wiring correspondance: colors versus connections. Document Number: 57099 Revision: 15-Nov-07 For technical questions, contact: sfer@vishay.com www.vishay.com 163 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1