732P105X9600L

Type 732P Vishay Sprague Film Capacitors Metalized Polypropylene, Wrap-and-Fill FEATURES • High stability • High ripple current to 30A • Low inductance and low ESR • Excellent AC performance PERFORMANCE CHARACTERISTICS Operating Temperature: - 55°C to + 105°C. Capacitance Range: 1.0µF to 30.0µF. Capacitance Tolerance: ± 10, ± 5%. Voltage Rating: 200 WVDC to 600 WVDC. Dissipation Factor: .10% maximum. Equivalent Series Resistance: 20kHz - 100kHz (see Standard Ratings table). Voltage Test: 200% of rated voltage for 2 minutes. ∆V/∆T: 10 volts/microsecond maximum. Insulation Resistance: At + 25°C, 100,000 Megohm - Microfarads or 200,000 Megohm minimum. DC Life Test: 140% of rated DC voltage for 250 hours at + 105°C. No open or short circuits. No visible damage evident. Maximum Capacitance Change: ± 1.0%. Minimum IR = 50% of initial limit. Maximum DF = .10%. Humidity Test: 95% relative humidity at + 40°C for 250 hours. No visible damage evident. Maximum Capacitance Change: ± 1.0%. Minimum IR = 20% of initial limit. Maximum DF = .12%. PHYSICAL CHARACTERISTICS Lead Pull: 5 pounds (2.3 kilograms) for one minute. No physical damage. Lead Bend: After three complete consecutive bends, no damage. Marking: Sprague® trademark, type or part number, capacitance and voltage. ENVIRONMENTAL CHARACTERISTICS Vibration Test (Condition B): No mechanical damage, short, open or intermittent circuits. STANDARD RATINGS in inches [millimeters] CAP. (µF) Max. ESR PART NUMBER* (Milliohms) ± 10% 20kHz CASE SIZE TOLERANCE D (Max.) x L ± 0.062 [1.57] 100kHz MAXIMUM RIPPLE CURRENT (Amps rms) @ 20kHz - 100kHz Case Temperature @ + 25°C + 35°C + 45°C + 55°C + 65°C + 75°C + 85°C 200 WVDC 1.0 2.0 3.0 5.0 10.0 20.0 30.0 732P105X9200L 732P205X9200L 732P305X9200L 732P505X9200L 732P106X9200L 732P206X9200L 732P306X9200L 0.531 x 0.750 [13.49 x 19.05] 0.596 x 0.938 [15.14 x 23.83] 0.717 x 0.938 [18.21 x 23.83] 0.733 x 1.250 [18.62 x 31.75] 0.898 x 1.500 [22.81 x 38.10] 1.000 x 2.250 [25.40 x 57.15] 1.200 x 2.250 [30.48 x 57.15] 15.0 12.0 11.0 10.0 9.0 8.0 6.0 9.2 10.8 12.1 13.8 15.0 15.0 15.0 8.5 10.0 11.2 12.7 15.0 15.0 15.0 7.8 9.1 10.3 11.6 14.2 15.0 15.0 7.0 8.2 9.4 10.4 12.7 15.0 15.0 6.0 7.0 8.0 9.0 11.0 13.6 15.0 4.9 5.8 6.5 7.4 9.0 11.1 12.4 4.5 5.3 5.9 8.7 8.2 10.0 11.4 400 WVDC 1.0 2.0 3.0 5.0 10.0 20.0 732P105X9400L 732P205X9400L 732P305X9400L 732P505X9400L 732P106X9400L 732P206X9400L 0.512 x 1.250 [13.00 x 31.75] 0.698 x 1.250 [17.73 x 31.75] 0.747 x 1.500 [18.97 x 38.10] 0.862 x 1.750 [21.89 x 44.45] 1.030 x 2.250 [26.16 x 57.15] 1.440 x 2.250 [36.58 x 57.15] 20.0 15.0 13.0 11.0 9.0 6.0 7.3 12.0 15.0 15.0 15.0 15.0 7.3 12.0 13.8 15.0 15.0 15.0 7.3 11.3 12.6 14.7 15.0 15.0 7.3 10.1 11.3 13.1 15.0 15.0 7.2 8.7 9.8 11.4 13.8 15.0 5.9 7.1 8.0 9.3 11.3 14.1 5.4 6.5 7.3 8.5 10.3 12.8 600 WVDC 1.0 2.0 3.0 5.0 10.0 732P105X9600L 732P205X9600L 732P305X9600L 732P505X9600L 732P106X9600L 0.713 x 1.500 [18.11 x 38.10] 0.895 x 1.750 [22.73 x 44.45] 1.086 x 1.750 [27.58 x 44.45] 1.192 x 2.250 [30.28 x 57.15] 1.668 x 2.250 [42.37 x 57.15] 19.0 15.0 12.0 10.0 6.0 9.5 15.0 15.0 15.0 15.0 9.5 15.0 15.0 15.0 15.0 9.5 15.0 15.0 15.0 15.0 9.5 13.4 15.0 15.0 15.0 9.5 11.6 13.1 15.0 15.0 7.8 9.5 10.7 12.5 15.0 7.1 8.7 9.8 11.4 14.1 * Part Numbers listed are for a capacitance tolerance of ± 10%. To specify ± 5% tolerance, change the "X9" in the Part Number to "X5". ORDERING INFORMATION 732P TYPE 105 CAPACITANCE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. Values must conform to the decade rating for the tolerance specified. X9 CAPACITANCE TOLERANCE X9 = ± 10% (Inventoried) X5 = ± 5% 200 DC VOLTAGE RATING This is expressed in volts. L TERMINAL L = Wire leads* * Leads are bare, solid tinned copper wire. Lead wire sizes are: Case diameter < .700" [17.78mm], lead AWG No. 20. Document Number: 42035 Revision 17-Nov-03 www.vishay.com 102 For technical questions, contact spresale@vishay.com