APD-128G064A-1

APD-128G064A-1 Vishay Dale Plasma Display Modules 128 x 64 Graphics Display with Drive Electronics, TTL Level Data Interface and DC to DC Converter FEATURES • TTL level video interface • Highly visible for long distance viewing • On board DC converter • Slim profile • Large, bright characters and graphics The APD-128G064A-1 DC plasma display offers viewing qualities designers seek such as high contrast, viewing angle of 150° minimum and long distance readability. Its bright (50 foot lambert minimum) with characters and graphics figures presented in a pleasing neon orange color against a black background. Plasma is much more readable and eye-pleasing than liquid crystal or vacuum fluorescent displays and is filterable to red, amber or neutral density.These plasma display panels are driven in a standard row-column refresh method much like a CRT display. The designer need only supply TTL level signals for SERIAL DATA, DOT CLOCK, COLUMN LATCH, ROW DATA, ROW CLOCK and DISPLAY ENABLE. The SERIAL DATA is entered with the DOT CLOCK up to frequencies as high as 8mHz. After a row of 128 pixels is clocked in, the COLUMN LATCH signal is toggled and the data is latched. At the time the data is latched, the display is briefly disabled using the DISPLAY ENABLE signal, then the row pointer is advanced with the ROW CLOCK signal. Once each frame the ROW DATA must be asserted to synchronize the column serial data with the beginning row. The recommended scanning frequency is approximately 70 Hz, but may be as high as 200 Hz. The high clock rate on the data clock allows for rapid refresh and maximum access time to the refresh ram. ELECTRICAL SPECIFICATIONS Power Required: Typical = 12 watts. Maximum = 35 watts. DIMENSIONS in inches [millimeters] 128 x 64 Full Field 14.50 [368.30] Column 1, Row 1 7.40 [187.96] .150 [3.81] STANDARD ELECTRICAL SPECIFICATIONS* DESCRIPTION Logic Supply Logic Current DC-DC Supply DC-DC Current** Logic 1 Input Logic 0 Input SYMBOL Vcc Icc VDC Idc Vih Vil MIN. + 4.5 — + 12.0 0.080 2.0 — TYP. + 5.0 0.050 + 24.0 0.750 — — MAX. + 5.5 — + 30.0 1.5 — 0.8 UNITS VDC Amps VDC Amps VDC VDC 7.825 [198.76] Center of Display Area 4.062 [103.17] 6.35 [161.29] 7.275 [184.78] 8.125 [206.38] .150 [3.81] *Recommended operating voltages. All maximums are to be considered absolute maximum. **Current is calculated at VDC = 24 VDC. The initial power on condition may require 2X maximum rating to initiate DC voltage conversion circuit. .487 [12.37] .888 [22.56] 13.775 [349.88] 1.025 14.80 [375.92] [26.04] Pin #1 of P1 .447 ± .020 [11.35 .062 [1.575] ± .508] 6.750 [165.10] Pin #1 PCB of P3 Thickness C 7.40 [187.96] L 7.25 [184.15] 12.75 [323.85] 8.775 [222.88] 10.50 [266.70] C L C L ORDERING INFORMATION DESCRIPTION PART NUMBER Display Module with Drivers and TTL Interface ............................................................................................. APD-128G064A Display Module with Drivers, TTL Interface and On Board DC Converter ................................................. APD-128G064A-1 Data Connector Kit ................................................................................................................................................. 280105-05 Power Connector Kit .............................................................................................................................................. 280108-13 www.vishay.com 2 Document Number: 37035 Revision 08-Nov-00 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1