BRT21

BRT21/BRT22/BRT23 Vishay Semiconductors Optocoupler, Phototriac Output, Zero Crossing FEATURES A C 1 2 ZCC* 6 MT2 5 NC • High input sensitivity IFT = 1.0 mA • ITRMS = 300 mA • High static dV/dt 10 000 V/µs • Electrically insulated between input and output circuit • Microcomputer compatible • Trigger current - (IFT < 1.2 mA) BRT22F, BRT23F, - (IFT < 2 mA) BRT21H, BRT22H, BRT23H - (IFT < 3 mA) BRT21M, BRT22M, BRT23M • Available surface mount and on on tape and reel • Zero voltage crossing detector • UL file E52744 system code J • DIN EN 60747-5-5 available with option 1 • Lead (Pb)-free component • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC NC 3 17223 4 MT1 *Zero Crossing Circuit DESCRIPTION The BRT21, BRT22, BRT23 product family consists of AC switch optocouplers with zero voltage detectors with two electrically insulated lateral power ICs which integrate a thyrister system, a photo detector and noise suppression at the output and an IR GaAs diode input. High input sensitivity is achieved by using an emitter follower phototransistor and a SCR predriver resulting in an LED trigger current of less than 2 mA or 3 mA (DC). Inverse parallel SCRs provide commutating dV/dt greater than 10 kV/µs. The zero cross line voltage detection circuit consists of two MOSFETS and a photodiode. The BRT21/22/23 product family isolates low-voltage logic from 120, 230, and 380 VAC lines to control resistive, inductive or capacitive loads including motors, solenoids, high current thyristers or TRIAC and relays. APPLICATIONS • Industrial controls • Office equipment • Consumer appliances ORDER INFORMATION PART BRT21H BRT21M BRT22F BRT22H BRT22M BRT23F BRT23H BRT23M BRT21H-X006 BRT21H-X007 BRT21M-X006 BRT22F-X006 BRT22H-X007 BRT22M-X006 BRT23F-X006 BRT23F-X007 BRT23H-X006 BRT23H-X007 BRT23M-X006 BRT23M-X007 Note For additional information on the available options refer to option information. Document Number: 83690 Rev. 1.5, 07-May-08 For technical questions, contact: optocouplers.answers@vishay.com www.vishay.com 193 REMARKS VDRM ≤ 400 V, DIP-6, IFT = 2.0 mA VDRM ≤ 400 V, DIP-6, IFT = 3.0 mA VDRM ≤ 600 V, DIP-6, IFT = 1.2 mA VDRM ≤ 600 V, DIP-6, IFT = 2.0 mA VDRM ≤ 600 V, DIP-6, IFT = 3.0 mA VDRM ≤ 800 V, DIP-6, IFT = 1.2 mA VDRM ≤ 800 V, DIP-6, IFT = 2.0 mA VDRM ≤ 800 V, DIP-6, IFT = 3.0 mA VDRM ≤ 400 V, DIP-6 400 mil (option 6), IFT = 2.0 mA VDRM ≤ 400 V, SMD-6 (option 7), IFT = 2.0 mA VDRM ≤ 400 V, DIP-6 400 mil (option 6), IFT = 3.0 mA VDRM ≤ 600 V, SMD-6 (option 7), IFT = 1.2 mA VDRM ≤ 600 V, SMD-6 (option 7), IFT = 2.0 mA VDRM ≤ 600 V, DIP-6 400 mil (option 6), IFT = 3.0 mA VDRM ≤ 800 V, DIP-6 400 mil (option 6), IFT = 1.2 mA VDRM ≤ 800 V, DIP-6 400 mil (option 6), IFT = 1.2 mA VDRM ≤ 800 V, DIP-6 400 mil (option 6), IFT = 2.0 mA VDRM ≤ 800 V, SMD-6 (option 7), IFT = 2.0 mA VDRM ≤ 800 V, DIP-6 400 mil (option 6), IFT = 3.0 mA VDRM ≤ 800 V, SMD-6 (option 7), IFT = 3.0 mA BRT21/BRT22/BRT23 Vishay Semiconductors Optocoupler, Phototriac Output, Zero Crossing (1) ABSOLUTE MAXIMUM RATINGS PARAMETER INPUT Reverse voltage Forward current Surge current Power dissipation Derate from 25 °C OUTPUT TEST CONDITION IR = 10 µA PART SYMBOL VR IF IFSM Pdiss VALUE 6.0 60 2.5 100 1.33 UNIT V mA A mW mW/°C V V V mA A mW mW/°C BRT21 Peak off-state voltage RMS on-state current Single cycle surge current Power dissipation Derate from 25 °C COUPLER Isolation test voltage (between emitter and detector, climate per DIN 500414, part 2, Nov. 74) Pollution degree (DIN VDE 0109) Creepage distance Clearance distance Comparative tracking index per DIN IEC 112/VDE 0303 part 1, group IIIa per DIN VDE 6110 Isolation resistance Storage temperature range Ambient temperature range Soldering temperature (2) max. ≤ 10 s dip soldering ≥ 0.5 mm from case bottom VIO = 500 V, Tamb = 25 °C VIO = 500 V, Tamb = 100 °C t = 1.0 min ID(RMS) = 70 µA BRT22 BRT23 VDM VDM VDM ITM Pdiss 400 600 800 300 3.0 600 6.6 VISO 5300 2 ≥ 7.0 ≥ 7.0 VRMS mm mm CTI RIO RIO Tstg Tamb Tsld ≥ 175 ≥ 1012 ≥ 1011 - 40 to + 100 - 40 to + 100 260 Ω Ω °C °C °C Notes (1) T amb = 25 °C, unless otherwise specified. Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (2) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). ELECTRICAL CHARACTERISTICS PARAMETER INPUT Forward voltage Reverse current Capacitance Thermal resistance, junction to ambient IF = 10 mA VR = 6 V f = 1 MHz, VF = 0 V VF IR CO RthJA 1.16 0.1 25 750 1.35 10 V µA pF K/W TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT www.vishay.com 194 For technical questions, contact: optocouplers.answers@vishay.com Document Number: 83690 Rev. 1.5, 07-May-08 BRT21/BRT22/BRT23 Optocoupler, Phototriac Output, Zero Crossing ELECTRICAL CHARACTERISTICS PARAMETER OUTPUT Off-state voltage Repetitive peak off-state voltage Off-state current On-state voltage On-state current Surge (non-repetitive), on-state current Trigger current temp. gradient Inhibit voltage temp. gradient Off-state current in inhibit state Holding current Latching current Zero cross inhibit voltage Turn-on time Turn-off time Critical rate of rise of off-state voltage Critical rate of rise of voltage at current commutation Critical rate of rise of on-state Thermal resistance, junction to ambient COUPLER Critical rate of rise of coupled input/output voltage Common mode coupling capacitance Capacitance (input to output) Isolation resistance f = 1.0 MHz, VIO = 0 V VIO = 500 V, Tamb = 25 °C VIO = 500 V, Tamb = 100 °C VD = 5.0 V, F - versions Trigger current VD = 5.0 V, H - versions VD = 5.0 V, M - versions IT = 0 A, VRM = VDM = VD(RMS) dVIO/dt CCM CIO Ris Ris IFT IFT IFT 10000 0.01 0.8 ≥ 1012 ≥ 1011 1.2 2.0 3.0 V/µs pF pF Ω Ω mA mA mA VT = 2.2 V IF = rated IFT VRM = VDM = VD(RMS) PF = 1.0, IT = 300 mA VD = 0.67 VDRM, Tj = 25 °C VD = 0.67 VDRM, Tj = 80 °C VD = 0.67 VDRM, dI/dtcrq ≤ 15 A/ms, Tj = 25 °C VD = 0.67 VDRM, dI/dtcrq ≤ 15 A/ms, Tj = 80 °C IF = IFT1, VDRM ID(RMS) = 70 µA IDRM = 100 µA VD = VDRM, Tamb = 100 °C, IF = 0 m A IT = 300 mA PF = 1.0, VT(RMS) = 1.7 V f = 50 Hz VD(RMS) VDRM ID(RMS) VTM ITM ITSM ΔIFT1/ΔTj ΔIFT2/ΔTj ΔVDINH/ΔTj IDINH IH IL VIH ton toff dV/dtcr dV/dtcr dV/dtcrq dV/dtcrq dI/dtcr RthJA 10000 5000 10000 5000 8.0 125 7.0 7.0 - 20 50 65 5.0 15 35 50 25 200 500 424 600 10 1.7 100 3.0 300 3.0 14 14 460 V V µA V mA A µA/K µA/K mV/K µA µA mA V µs µs V/µs V/µs V/µs V/µs A/µs K/W TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Vishay Semiconductors Note Tamb = 25 °C, unless otherwise specified. Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Document Number: 83690 Rev. 1.5, 07-May-08 For technical questions, contact: optocouplers.answers@vishay.com www.vishay.com 195 BRT21/BRT22/BRT23 Vishay Semiconductors Optocoupler, Phototriac Output, Zero Crossing SAFETY AND INSULATION RATINGS PARAMETER Climatic classification (according to IEC 68 part 1) Comparative tracking index VIOTM VIORM PSO ISI TSI Creepage distance Clearance distance Creepage distance Clearance distance standard DIP-6 standard DIP-6 400 mil DIP-6 400 mil DIP-6 7 7 8 8 CTI 175 6000 630 200 400 175 TEST CONDITION SYMBOL MIN. TYP. 40/100/21 399 V V mW mA °C mm mm mm mm MAX. UNIT Note As per IEC 60747-5-2, § 7.4.3.8.1, this optocoupler is suitable for "safe electrical insulation" only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. POWER FACTOR CONSIDERATIONS A snubber is not needed to eliminate false operation of the TRIAC driver because of the high static and commutating dV/dt with loads between 1.0 and 0.8 power factors. When inductive loads with power factors less than 0.8 are being driven, include a RC snubber or a single capacitor directly across the device to damp the peak commutating dV/dt spike. Normally a commutating dV/dt causes a turning-off device to stay on due to the stored energy remaining in the turning-off device. But in the case of a zero voltage crossing optotriac, the commutating dV/dt spikes can inhibit one half of the TRIAC from turning on. If the spike potential exceeds the inhibit voltage of the zero cross detection circuit, half of the TRIAC will be heldoff and not turn-on. This hold-off condition can be eliminated by using a snubber or capacitor placed directly across the optotriac as shown in Figure 1. Note that the value of the capacitor increases as a function of the load current. The hold-off condition also can be eliminated by providing a higher level of LED drive current. The higher LED drive provides a larger photocurrent which causes the phototransistor to turn-on before the commutating spike has activated the zero cross network. Figure 2 shows the relationship of the LED drive for power factors of less than 1.0. The curve shows that if a device requires 1.5 mA for a resistive load, then 1.8 times 2.7 mA) that amount would be required to control an inductive load whose power factor is less than 0.3. 1 Cs (µF) = 0.0032 (µF)*10^0.0066 IL (mA) Cs - Shunt Capacitance (µF) 0.1 0.01 Ta = 25 °C, PF = 0.3 IF = 2.0 mA 0.001 0 iil410_01 50 100 150 200 250 300 350 400 IL - Load Current (mA) (RMS) Fig. 1 - Shunt Capacitance vs. Load Current www.vishay.com 196 For technical questions, contact: optocouplers.answers@vishay.com Document Number: 83690 Rev. 1.5, 07-May-08 BRT21/BRT22/BRT23 Optocoupler, Phototriac Output, Zero Crossing TYPICAL CHARACTERISTICS Tamb = 25 °C, unless otherwise specified Vishay Semiconductors 2.0 150 NIFth - Normalized LED Trigger Current 1.8 1.6 1.4 1.2 1.0 0.8 0.0 LED - LED Power (mW) IFth Normalized to IFth at PF = 1.0 Ta = 25 °C 100 50 0.2 0.4 0.6 0.8 1.0 1.2 0 - 60 - 40 - 20 iil410_05 0 20 40 60 80 100 iil410_02 PF - Power Factor Ta - Ambient Temperature (°C) Fig. 2 - Normalized LED Trigger Current vs. Power Factor Fig. 5 - Maximum LED Power Dissipation 1.4 103 5 Ta = - 55 °C Tj = 25 °C 100 °C VF - Forward Voltage (V) 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.1 IT (mA) 102 5 Ta = 25 °C IT = f(VT), Parameter: Tj Ta = 85 °C 101 5 100 1 10 100 iil410_06 0 1 2 3 4 iil410_03 IF - Forward Current (mA) VT (V) Fig. 3 - Forward Voltage vs. Forward Current Fig. 6 - Typical Output Characteristics 10000 If(pk) - Peak LED Current (mA) τ Duty Factor 1000 0.005 0.01 0.02 0.05 0.1 0.2 0.5 t DF = τ/t 400 ITRMS = f(VT), RthJA = 150 K/W Device switch soldered in pcb or base plate. ITRMS (mA) 101 300 200 100 100 10 10-6 10-5 10-4 10-3 10-2 10-1 10 0 iil410_04 0 0 iil410_07 20 40 60 80 100 t - LED Pulse Duration (s) TA (°C) Fig. 7 - Current Reduction Fig. 4 - Peak LED Current vs. Duty Factor, Tau Document Number: 83690 Rev. 1.5, 07-May-08 For technical questions, contact: optocouplers.answers@vishay.com www.vishay.com 197 BRT21/BRT22/BRT23 Vishay Semiconductors Optocoupler, Phototriac Output, Zero Crossing 400 0.6 0.5 40 to 60 Hz Line operation, Ptot = f(ITRMS) ITRMS (mA) 300 Ptot (W) ITRMS = f(TPIN5), RthJ-PIN5 = 16.5 K/W Thermocouple measurement must be performed potentially separated to A1 and A2. Measuring junction as near as possible at the case. 0.4 0.3 0.2 0.1 0 200 100 0 50 iil410_08 60 70 80 90 100 iil410_11 0 100 200 300 TPIN5 (°C) Fig. 8 - Current Reduction ITRMS (mA) Fig. 11 - Power Dissipation 40 to 60 Hz Line Operation 12 103 V tgd = f (IFIFT 25 °C), VD = 200 V f = 40 to 60 Hz, Parameter: Tj Tj = 25 °C 100 °C fgd (µs) VDINH min. (V) 10 8 102 5 Tj = 25 °C 100 °C 6 4 101 100 iil410_09 VDINH min = f (IF/IFT25°C), parameter: Tj Device zero voltage switch can be triggered only in hatched are below Tj cur ves. 5 101 5 102 100 iil410_12 5 101 5 102 IF/IFT25 °C IF/IFT25 °C Fig. 9 - Typical Trigger Delay Time Fig. 12 - Typical Static Inhibit Voltage Limit 103 Tj = 25 °C 100 °C 1 6 IDINH (µs) 102 5 2 5 0.1 µF 220 V~ 101 5 IDINH = f (IF /IFT 25 °C), VD = 600 V, Parameter: Tj 0 iil410_10 3 4 100 2 4 6 8 10 12 14 16 18 20 iil410_13 IF/IFT25 °C Fig. 13 - 1- Apply a Capacitor to the Supply Pins at the Load-Side Fig. 10 - Typical Inhibit Current www.vishay.com 198 For technical questions, contact: optocouplers.answers@vishay.com Document Number: 83690 Rev. 1.5, 07-May-08 BRT21/BRT22/BRT23 Optocoupler, Phototriac Output, Zero Crossing 33 Ω 1 6 1 6 Vishay Semiconductors 500 µH 2 5 22 nF 220 V~ 2 5 22 nF 220 V~ 3 4 3 4 iil410_14 iil410_15 Fig. 14 - 2 - Connect a Series Resistor to the Output and Bridge Both by a Capacitor Fig. 15 - 3 - Connect a Choke of Low Winding Cap. in Series, e.g., a Ringcore Choke, with Higher Load Currents TECHNICAL INFORMATION See Application Note for additional information. PACKAGE DIMENSIONS in inches (millimeters) 3 0.248 ( 6.30 ) 0.256 (6.50 ) 4 2 1 pin one ID ISO method A 5 6 0.37 5 (9.53 ) 0.395 (10.03) 0.300 (7.62) ref. 0.33 5 ( 8.50 ) 0.343 ( 8.70 ) 0.03 9 (1.00) min. 0.048 (1.22) 0.052 (1.32) 0.130 (3.30) 0.150 (3.81) 0.0040 (0.102) 0.0098 (0.249) 0.012 (0.30) typ. 4° typ . 0.018 (0.46) 0.020 (0.51 ) 0.033 (0.84) typ. 0.033 (0.84 ) typ. 0.100 (2.54) typ. 0.020 (0.51) 0.040 (1.02) 15 ° max. 17222 Option 6 0.407 (10.36) 0.391 (9.96) 0.307 (7.8) 0.291 (7.4) 0.028 (0.7) Option 7 0.300 (7.62) typ. 0.180 (4.6) 0.160 (4.1) 0.315 (8.0) min. 0.014 (0.35) 0.010 (0.25) 0.400 (10.16) 0.430 (10.92) 0.331 (8.4) min. 0.406 (10.3) max. 18450-1 Document Number: 83690 Rev. 1.5, 07-May-08 For technical questions, contact: optocouplers.answers@vishay.com www.vishay.com 199 BRT21/BRT22/BRT23 Vishay Semiconductors Optocoupler, Phototriac Output, Zero Crossing OZONE DEPLETING SUBSTANCES POLICY STATEMENT It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively. 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA. 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany www.vishay.com 200 For technical questions, contact: optocouplers.answers@vishay.com Document Number: 83690 Rev. 1.5, 07-May-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1