CRA04P0830000ZTD

CRA04P Vishay Thick Film, Resistor Array FEATURES • Concave terminal array with square corners The CRA04P thick film resistor array is constructed on a high grade ceramic body with concave terminations. A small package enables the design of high density circuits. The single component reduces board space, component counts and assembly costs. • • • • Wide ohmic range: 1R0 to 1M0 8 terminal package with isolated resistors Lead (Pb)-free solder contacts on NI barrier layer Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes • Compatible with “Restriction of the use of Hazardous Substances” (RoHS) directive 2002/95/EC (issue 2004) STANDARD ELECTRICAL SPECIFICATIONS MODEL CIRCUIT POWER RATING P70 °C W 0.063 LIMITING ELEMENT VOLTAGE MAX V≅ 50 TEMPERATURE COEFFICIENT ppm/K ± 100 ± 200 TOLERANCE % ±2 ±5 RESISTANCE RANGE Ω 10R - 1M0 1R0 - 1M0 E-SERIES 24 24 CRA04P 03 Zero-Ohm-Resistor: Rmax = 50 mΩ, Imax = 1 A TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70 °C2) Limiting Element Voltage1) Insulation Voltage (1 min) Category Temperature Range Insulation Resistance UNIT W per element V≅ Vdc/ac peak °C Ω CRA04P 0.063 50 100 - 55/+ 125 (+ 155) > 109 Notes 1. Rated voltage: P × R 2. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. PART NUMBER AND PRODUCT DESPRIPTION PART NUMBER: CRA04P08347K0JTD1) C MODEL CRA04 R A 0 4 PIN 08 P 0 CIRCUIT 3 = 03 8 3 4 7 K 0 J T D SPECIAL up to 2 digits TERMINAL STYLE P VALUE R = Decimal K = Thousand M = Million 0000 = 0 Ω Jumper TOLERANCE G=±2% J=±5% Z = 0 Ω Jumper PACKAGING2) TD TC PZ PRODUCT DESCRIPTION: CRA04P 08 03 473 J RT7 e3 CRA04P MODEL CRA04P 08 TERMINAL COUNT 08 03 CIRCUIT TYPE 03 473 RESISTANCE VALUE 473 = 47 kΩ 4R7 = 4.7 Ω 100 = 10 Ω 000 = 0 Ω Jumper First two digits (3 for 1 %) are significant. Last digit is the multiplier. J TOLERANCE G=±2% J=±5% Z = 0 Ω Jumper RT7 PACKAGING2) RT7 RT6 PZ e3 LEAD (Pb)-FREE e3 = Pure Tin Termination Finish Notes 1. Preferred way for ordering products is by use of the PART NUMBER. 2. Please refer to the table PACKAGING, see next page. Document Number: 31048 Revision: 09-Jan-07 For Technical Questions contact: ff3fresistors@vishay.com www.vishay.com 1 CRA04P Vishay PACKAGING PACKING CODE MODEL TAPE WIDTH DIAMETER PITCH PIECES/REEL PART NUMBER 180 mm/7" CRA04P 8 mm 330 mm/13" 330 mm/13" 2 mm 2 mm 2 mm 10 000 20 000 50 000 TD TC PZ PAPER TAPE PRODUCT DESCRIPTION RT7 RT6 PZ Thick Film, Resistor Array CIRCUIT 03 Circuit 120 100 80 60 40 20 0 - 55 Rated Power in % - 25 0 25 50 Derating 100 125 150 175 75 70 Ambient Temperature in °C DIMENSIONS A C DIMENSIONS [in millimeters] PIN NO# W L A B C PNOM T W 8 P L B 2.00 0.20 0.32 0.25 0.50 0.35 1.00 T TOL ± 0.10 ± 0.10 ± 0.10 ± 0.10 - ± 0.10 ± 0.10 SOLDER PAD DIMENSIONS [in millimeters] c w c w p a b b WAVE 0.5 1.5 0.5 0.32 0.5 p a www.vishay.com 2 For Technical Questions contact: ff3fresistors@vishay.com Document Number: 31048 Revision: 09-Jan-07 CRA04P Thick Film, Resistor Array Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS PERMISSIBLE CHANGE (ΔR/R)1) CONDITIONS OF TEST STABILITY CLASS 2 OR BETTER stability for product types: CRA04P Resistance (4.5) Temperature coefficient (4.8.4.2) 20/- 55/20 °C and 20/125/20 °C U = 2.5 × (P70 x R)1/2 ≤ 2 x Umax; 0.5 s Aging 4 h at 155 °C, dryheat Solder bath method; 235 °C; 2 s Visual examination Solder bath method; (260 ± 5) °C; (10 ± 1) s 30 min. at LCT = - 55 °C; 30 min. at UCT = 125 °C; 5 cycles (40 ± 2) °C; 56 days; (93 ± 3) % RH 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = - 55 °C; 1 h/1 kPa at 15 °C to 35 °C; 5 cycles at 55 °C U = (P70 x R)1/2 U = Umax; whichever is less severe U = (P70 x R)1/2 U = Umax; whichever is less severe 1.5 h on; 0.5 h off; 70 °C; 1000 h Duration extended to 8000 hours UCT = 125 °C; 1000 h ±2% ± 100 ppm/K ±5% ± 200 ppm/K 10 Ω to 1 MΩ 1 Ω to 1 M Ω TEST (clause) Overload (4.13) ± (0.5 % R + 0.05 Ω) Good tinning (≥ 95 % covered) no visible damage ± (0.5 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Solderability (4.17.5)2) Resistance to soldering heat (4.18.2) Rapid change of temperature (4.19) Damp heat, steady state (4.24) Climatic sequence (4.23) ± (2 % R + 0.1 Ω) Endurance at 70 °C (4.25.1) ± (2 % R + 0.1 Ω) Extended endurance (4.25.1.8) Endurance at upper category temperature (4.25.3) ± (4 % R + 0.1 Ω) ± (2 % R + 0.1 Ω) Notes 1. Figures are given for a single element. 2. Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years. APPLICABLE SPECIFICATIONS • EN 60115-1 • EN 140400 • EN 140401-802 • IEC 60068-2-X • EIA 481 Generic Specification Sectional Specification Detail Specification Variety of environmental test procedures Packaging of SMD components Document Number: 31048 Revision: 09-Jan-07 For Technical Questions contact: ff3fresistors@vishay.com www.vishay.com 3 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1