CRA06P0403100ZRT1E3

CRA06P Vishay Thick Film Resistor Array FEATURES • Concave terminal array with square corners CRA06P Thick Film resistor array is constructed on a high grade ceramic body with concave terminations. A small package enables the design of high density circuits. The single component reduces board space, component counts and assembly costs. • • • • 4 and 8 terminal package with isolated resistors Wide ohmic range: 10R to 1M0 Lead (Pb)-free solder contacts on Ni barrier layer Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes • Compatible with "Restriction of the use of Hazardous Substances" (RoHS) directive 2002/95/EC (issue 2004) STANDARD ELECTRICAL SPECIFICATIONS MODEL CIRCUIT POWER RATING P70 °C W TEMPERATURE COEFFICIENT ppm/K ± 100 0.063 50 ± 200 Zero-Ohm-Resistor: Rmax. = 50 mΩ, Imax. = 1 A LIMITING ELEMENT VOLTAGE MAX. V≅ TOLERANCE % ±1 ± 2; ± 5 RESISTANCE RANGE Ω 10R - 1M0 E-SERIES 24 + 96 24 CRA06P 03 TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70 °C (2) Limiting Element Voltage (1) Insulation Voltage (1 min) Category Temperature Range Insulation Resistance UNIT W per element V≅ Vdc/ac peak °C Ω CRA06P 03 CIRCUIT 0.063 50 100 - 55 to + 155 > 109 Notes (1) Rated voltage: P × R (2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. PART NUMBER AND PRODUCT DESPRIPTION PART NUMBER: CRA06P08347K0JTA (3) C MODEL CRA06 R A 0 6 PIN 04 08 P 0 CIRCUIT 3 = 03 8 3 4 7 K 0 J T A SPECIAL Up to 2 digits TERMINAL STYLE P VALUE R = Decimal K = Thousand M = Million 0000 = 0 Ω Jumper TOLERANCE F=±1% G=±2% J=±5% Z = 0 Ω Jumper PACKAGING (4) TA TC PRODUCT DESCRIPTION: CRA06P 08 03 473 J RT1 e3 CRA06P MODEL CRA06P 08 TERMINAL COUNT 04 08 03 CIRCUIT TYPE 03 473 RESISTANCE VALUE 473 = 47 kΩ 4702 = 47 kΩ 10R0 = 10 Ω 100 = 10 Ω 000 = 0 Ω Jumper First two digits (3 for 1 %) are significant. Last digit is the multiplier. J TOLERANCE F=±1% G=±2% J=±5% Z = 0 Ω Jumper RT1 PACKAGING (4) RT1 RT6 e3 LEAD (Pb)-FREE e3 = Pure tin Termination finish (3) (4) Notes Preferred way for ordering products is by use of the PART NUMBER Please refer to the table PACKAGING, see next page For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 31047 Revision: 13-Oct-08 www.vishay.com 256 CRA06P Thick Film Resistor Array Vishay PACKAGING MODEL TAPE WIDTH DIAMETER PITCH PIECES /REEL 5000 20 000 PACKAGING CODE PAPER TAPE PART NUMBER TA TC PRODUCT DESCRIPTION RT1 RT6 180 mm/7" CRA06P 8 mm 330 mm/13" 4 mm 4 mm CIRCUIT Rated Power in % 120 100 03 CIRCUIT 80 60 40 20 4 pin 8 pin 0 - 55 - 25 0 25 50 Derating DIMENSIONS 75 70 100 125 155 175 Ambient Temperature in °C A w C PIN NO# 4 8 DIMENSIONS [in millimeters] L 1.60 3.20 A 0.30 0.30 B 0.40 0.40 C 0.40 0.40 P 0.80 0.80 T 0.60 0.60 W 1.60 1.60 P L B T Tol. ± 0.20 ± 0.20 ± 0.15 ± 0.20 ± 0.10 ± 0.15 SOLDER PAD DIMENSIONS [in millimeters] c c w w 2.6 p 0.8 a 0.4 b 0.9 WAVE 0.8 b p a Document Number: 31047 Revision: 13-Oct-08 For technical questions, contact: filmresistors.thickfilmchip@vishay.com www.vishay.com 257 CRA06P Vishay Thick Film Resistor Array TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS PERMISSIBLE CHANGE (ΔR/R) (1) CONDITIONS OF TEST STABILITY CLASS 1 OR BETTER Stability for product types: CRA06P Resistance (4.5) Temperature coefficient (4.8.4.2) 20/- 55/20 °C and 20/125/20 °C U = 2.5 × (P70 x R)1/2 ≤ 2 x Umax.; 0.5 s Aging 4 h at 155 °C, dryheat Solder bath method; 235 °C; 2 s Visual examination Solder bath method; (260 ± 5) °C; (10 ± 1) s 30 min at LCT = - 55 °C; 30 min at UCT = 125 °C; 5 cycles (40 ± 2) °C; 56 days; (93 ± 3) % RH 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = - 55 °C; 1 h/1 kPa at 15 °C to 35 °C; 5 cycles at 55 °C U = (P70 x R)1/2 U = Umax.; whichever is less severe U = (P70 x R)1/2 U = Umax.; whichever is less severe 1.5 h ON; 0.5 h OFF; 70 °C; 1000 h Duration extended to 8000 h UCT = 125 °C; 1000 h ±1% ± 100 ppm/K ± (0.25 % R + 0.05 Ω) ± 2 %; ± 5 % ± 200 ppm/K ± (0.5 % R + 0.05 Ω) 10 Ω to 1 MΩ STABILITY CLASS 2 OR BETTER 10 Ω to 1 MΩ TEST (clause) Overload (4.13) Solderability (4.17.5) (2) Good tinning (≥ 95 % covered) no visible damage ± (0.25 % R + 0.05 Ω) ± (0.25 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Resistance to soldering heat (4.18.2) Rapid change of temperature (4.19) Damp heat, steady state (4.24) Climatic sequence (4.23) ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Endurance at 70 °C (4.25.1) ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) Extended endurance (4.25.1.8) Endurance at upper category temperature (4.25.3) ± (2 % R + 0.1 Ω) ± (1 % R + 0.05 Ω) ± (4 % R + 0.1 Ω) ± (2 % R + 0.1 Ω) Notes (1) Figures are given for a single element (2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years APPLICABLE SPECIFICATIONS • EN 60115-1 • EN 140400 • EN 140401-802 • IEC 60068-2-X • EIA 481 Generic Specification Sectional Specification Detail Specification Variety of environmental test procedures Packaging of SMD components www.vishay.com 258 For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 31047 Revision: 13-Oct-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1