CRCA12E081100100E

CRCA Vishay Dale Thick Film Array, Resistor/Capacitor FEATURES • Single component reduces board space and • • • • • • • component counts Choice of dielectric characteristics X7R or Y5U Wrap around termination Thick film R/C element Inner electrode protection Flow & Reflow solderable Automatic placement capability, standard size 8 or 10 pin configurations STANDARD ELECTRICAL SPECIFICATIONS RESISTOR GLOBAL POWER RATING MODEL P70 °C W CRCA12E CRCA12S CRCA12E CRCA12S 0.125 0.125 TEMPERATURE TOLERANCE COEFFICIENT ppm/°C % 200 200 5 5 VALUE RANGE Ω 10R - 1M0 10R - 1M0 CAPACITOR TEMPERATURE TOLERANCE VOLTAGE DIELECTRIC COEFFICIENT RATING % % VDC X7R Y5U ± 15 + 20, - 56 20 20 50 50 VALUE RANGE pF 10 - 270 270 - 1800 RESISTOR • Operating Temperature Range: X7R - 55 °C to + 125 °C • Technology: Thick Film Notes • Ask about extended value ranges • Packaging: according to EIA 481 CAPACITOR • Operating Temperature Range: X7R - 55 °C to + 125 °C Y5U - 30 °C to + 85 °C • Maximum Dissipation Factor: 2.5 % • Dielectric Withstanding Voltage: 125 Vdc , 5 sec, 50 mA Charge • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70 °C (CECC 40401 I EIA 575) Capacitor Voltage Rating Dielectric Withstanding Voltage (5 sec, 50 mA Charge) Category Temperature Range Insulation Resistance UNIT W V Vdc °C Ω RESISTOR 0.125 - 55/+ 155 X7R CAPACITOR 50 125 - 55/+ 125 > 1010 Y5U CAPACITOR 50 125 - 30/+ 85 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: CRCA12E081472220R (preferred part numbering format) C MODEL CRCA12E CRCA12S R C A 1 2 E 0 8 1 4 7 2 2 2 0 R PIN COUNT SCHEMATIC 08 = 8 Pin 10 = 10 Pin 1 = 01 2 = 02 3 = 03 0 = Special RESISTANCE CAPACITANCE PACKAGING SPECIAL VALUE VALUE 2 digit significant 2 digit significant E = Lead (Pb)-free, T/R (2000 pcs) (Dash Number) figures, followed by figures, followed by (up to 1 digit) R = Tin/Lead, T/R (2000 pcs) a multiplier multiplier Blank = Standard 100 = 10 Ω 100 = 10 pF 683 = 68 kΩ 271 = 270 pF 105 = 1.0 MΩ 182 = 1800 pF (Tolerance = ± 5 %) (Tolerance = ± 20 %) Historical Part Number example: CRCA12E0801472J220MRB8 (will continue to be accepted) CRCA12E MODEL 08 PIN COUNT 01 SCHEMATIC 472 RESISTANCE VALUE J TOLERANCE 220 CAPACITANCE VALUE M TOLERANCE RB8 PACKAGING www.vishay.com 280 For technical questions, contact: ff2aresistors@vishay.com Document Number: 31044 Revision: 15-Jan-07 CRCA Thick Film Array, Resistor/Capacitor Vishay Dale DIMENSIONS 8-Terminal device S-Version E-Version a e GLOBAL MODEL CRCA12E CRCA12S CRCA12E CRCA12S PIN NO# 8 8 10 10 SIZE INCH METRIC 2012 5032 2012 5032 2512 6432 2512 6432 L 5.1 ± 0.15 5.1 ± 0.15 6.4 ± 0.15 6.4 ± 0.15 c 2.2 2.2 W 3.05 ± 0.15 3.05 ± 0.15 3.05 ± 0.15 3.05 ± 0.15 T 0.61 ± 0.10 0.61 ± 0.10 0.61 ± 0.10 0.61 ± 0.10 DIMENSIONS [in millimeters] B B* A A* DNOM 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.25 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.89 ± 0.15 0.25 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.25 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.89 ± 0.15 0.25 a 0.71 0.71 b 1.05 0.86 PNOM 1.27 1.27 1.27 1.27 e 1.09 1.09 WAVE SOLDERING REFLOW SOLDERING SOLDER PAD DIMENSIONS [in millimeters] w d p 4.3 0.57 1.27 3.9 0.57 1.27 Note 1. The images shown are for an 8 pin Part. For a 10 pin part, use the same pitch and add another pair of “a” dimension pads to the inner solder pads. SCHEMATICS 01 Circuit CRCA12E & S 02 Circuit CRCA12E & S 03 Circuit CRCA12E & S Rated Power in % 120 100 80 60 40 20 0 - 55 10 Pin only 10 Pin only 8 Pin 10 Pin - 25 0 25 50 Derating 75 100 125 150 175 70 Ambient Temperature in °C PERFORMANCE TEST Endurance Test at 70 °C MIL-Std-202 Method 108 Dielectric Withstanding Voltage MIL-Std-202 Method 301 Thermal Shock MIL-Std-202 Method 107 Moisture MIL-Std-202 Method 106 Resistance to Soldering Heat EIA 575 High Temperature Exposure EIA 575 Low Temperature Operation EIA 575 Solderability & Leaching EIA 575 3.12 CONDITIONS OF TEST 1000 hours at 70 °C, 1.5 hours "ON", 0.5 hours "OFF" 125 Vdc, 5 seconds, 50 mA charge 100 cycles, - 55 to + 125 °C Omit steps 7A and B 10 seconds at 260 °C solder bath temperature 125 °C for 100 hours 1 hour at - 55 °C then 45 minutes at 50 V Condition C TEST RESULTS R ± (5 % + 2 Ω) C ± 20 % no physical damage ± (5 % + 2 Ω) ± (5 % + 2 Ω) ± (5 % + 2 Ω) ± (5 % + 2 Ω) ± (5 % + 2 Ω) ± 20 % ± 20 % ± 20 % ± 20 % ± 20 % 95 % Coverage APPLICABLE SPECIFICATIONS • IPC Standards • EIA 575 Document Number: 31044 Revision: 15-Jan-07 For technical questions, contact: ff2aresistors@vishay.com www.vishay.com 281 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1