FCSP0530ETR

FCSP0530ETR Vishay High Power Products FlipKY®, 0.5 A FEATURES • • • • • Ultralow VF to footprint area Very low profile (< 0.6 mm ) Low thermal resistance Supplied tested and on tape and reel Designed for consumer level APPLICATIONS • • • • • Reverse polarity protection Current steering Freewheeling Flyback Oring FlipKY® DESCRIPTION FlipKY® product family utilizes wafer level chip scale packaging to deliver Schottky diodes with the lowest VF to PCB footprint area in the industry. The three pad 0.9 mm x 1.2 mm devices can deliver up to 0.5 A and occupy only 1.08 mm2 of board space. The anode and cathode connections are made through solder bump pads on one side of the silicon rather than through protruding leads enabling designers to strategically place the diodes on the PCB. This design not only minimizes board space but also reduces thermal resistance and inductance, which can improve overall circuit efficiency. Typical applications include hand-held, portable equipment such as cell phones, MP3 players, PDAs, and portable hard disk drives where space savings and performance are crucial. PRODUCT SUMMARY IF(AV) VR 0.5 A 30 V MAJOR RATINGS AND CHARACTERISTICS SYMBOL IF(AV) VRRM IFSM VF TJ tp = 5 µs sine 0.5 Apk, TJ = 125 °C Range CHARACTERISTICS Rectangular waveform VALUES 0.5 30 190 0.33 - 55 to 150 UNITS A V A V °C VOLTAGE RATINGS PARAMETER Maximum DC reverse voltage Maximum working peak reverse voltage SYMBOL VR VRWM FCSP0530ETR 30 UNITS V Document Number: 93429 Revision: 26-Aug-08 For technical questions, contact: diodes-tech@vishay.com www.vishay.com 1 FCSP0530ETR Vishay High Power Products ABSOLUTE MAXIMUM RATINGS PARAMETER Maximum average forward current Maximum peak one cycle non-repetitive surge current at TJ = 25 °C Non-repetitive avalanche energy Repetitive avalanche current SYMBOL IF(AV) IFSM 10 ms sine or 6 ms rect. pulse EAS IAR TEST CONDITIONS 50 % duty cycle at TPCB = 133 °C, rectangular waveform 5 µs sine or 3 µs rect. pulse Following any rated load condition and with rated VRRM applied VALUES 0.5 190 10 5 0.5 mJ A A UNITS FlipKY®, 0.5 A TJ = 25 °C, IAS = 2.0 A, L = 5.0 mH Current decaying linearly to zero in 1 µs Frequency limited by TJ maximum VA = 1.5 x VR typical ELECTRICAL SPECIFICATIONS PARAMETER SYMBOL 0.5 A Maximum forward voltage drop See fig. 1 VFM (1) 1A 0.5 A 1A Maximum reverse leakage current See fig. 2 Maximum junction capacitance Maximum voltage rate of charge Note (1) Pulse width < 300 µs, duty cycle < 2 % IRM (1) CT dV/dt TJ = 25 °C TJ = 125 °C Rated VR TEST CONDITIONS TJ = 25 °C TJ = 125 °C VR = Rated VR TYP. 0.40 0.45 0.29 0.36 10 5 MAX. 0.44 0.49 0.33 0.39 50 15 90 10 000 µA mA pF V/µs V UNITS VR = 5 VDC (test signal range 100 kHz to 1 MHz) 25 °C THERMAL - MECHANICAL SPECIFICATIONS PARAMETER Maximum junction and storage temperature range Typical thermal resistance, junction to PCB Typical thermal resistance, junction to ambient Notes (1) (2) SYMBOL TJ (1), TStg RthJL (2) RthJA (2) DC operation TEST CONDITIONS VALUES - 55 to 150 35 UNITS °C °C/W 150 dP tot 1 ------------ < ------------- thermal runaway condition for a diode on its own heatsink dT J R thJA Mounted on dual sided 0.58" square FR4 PCB with 0.2 square inches of 1 oz. top copper area www.vishay.com 2 For technical questions, contact: diodes-tech@vishay.com Document Number: 93429 Revision: 26-Aug-08 FCSP0530ETR FlipKY®, 0.5 A Vishay High Power Products 1000 10 CT - Junction Capacitance (pF) IF - Instantaneous Forward Current (A) 1.0 TJ = 150 °C TJ = 125 °C TJ = 25 °C 100 TJ = 25 °C 0.1 10 0 0.2 0.4 0.6 0.8 1.0 1.2 0 10 20 30 VFM - Forward Voltage Drop (V) Fig. 1 - Maximum Forward Voltage Drop Characteristics (Per Leg) 100 VR - Reverse Voltage (V) Fig. 3 - Typical Junction Capacitance vs. Reverse Voltage (Per Leg) 160 10 1.0 0.1 0.01 0.001 0.0001 TJ = 150 °C TJ = 125 °C TJ = 100 °C TJ = 75 °C TJ = 50 °C TJ = 25 °C Allowable Case Temperature (°C) IR - Reverse Current (mA) DC 140 D = 3/4 D = 1/2 D = 1/3 D = 1/4 D = 1/5 120 100 Square wave (D = 0.50) 80 % VR applied See note (1) 80 0 5 10 15 20 25 30 0 0.2 0.4 0.6 0.8 VR - Reverse Voltage (V) Fig. 2 - Typical Values of Reverse Current vs. Reverse Voltage (Per Leg) 0.3 IF(AV) - Average Forward Current (A) Fig. 4 - Maximum Allowable Case Temperature vs. Average Forward Current (Per Leg) Average Power Loss (W) 0.2 D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 RMS limit 0.1 DC 0 0 0.2 0.4 0.6 0.8 IF(AV) - Average Forward Current (A) Fig. 5 - Forward Power Loss Characteristics (Per Leg) Note (1) Formula used: T = T - (Pd + Pd C J REV) x RthJC; Pd = Forward power loss = IF(AV) x VFM at (IF(AV)/D) (see fig. 6); PdREV = Inverse power loss = VR1 x IR (1 - D); IR at 80 % VR applied Document Number: 93429 Revision: 26-Aug-08 For technical questions, contact: diodes-tech@vishay.com www.vishay.com 3 FCSP0530ETR Vishay High Power Products FlipKY®, 0.5 A 1000 IFSM - Non-Repetitive Surge Current (A) 100 10 At any rated load condition and with rated VRRM applied following surge 1 10 100 1000 10 000 tp - Square Wave Pulse Duration (µs) Fig. 6 - Maximum Non-Repetitive Surge Current (Per Leg) L High-speed switch Freewheel diode 40HFL40S02 + Vd = 25 V D.U.T. IRFP460 Rg = 25 Ω Current monitor Fig. 7 - Unclamped Inductive Test Circuit LINKS TO RELATED DOCUMENTS Dimensions Part marking information Packaging information http://www.vishay.com/doc?95049 http://www.vishay.com/doc?95060 http://www.vishay.com/doc?95062 www.vishay.com 4 For technical questions, contact: diodes-tech@vishay.com Document Number: 93429 Revision: 26-Aug-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1