GS1117CM-5

GS1117 New Product Vishay Semiconductors formerly General Semiconductor 800mA Low Dropout Positive Adjustable Regulator SOT-223 TO-252 (DPak) TO-220AB TO-263AB (D2Pak) 1 2 3 1 1 3 2 1 2 3 2 3 GS1117CST GS1117CE GS1117CT GS1117CM Pin Definition 1. Adjust/Gnd. 2. Vout (tab) 3. Vin Description The GS1117 is a low dropout three terminal regulator with 800mA output current capability. The output voltage is adjustable with the use of a resistor divider. For fixed output voltage versions, the output voltage is internally set at 2.5V, 2.85V, 3.3V or 5V. Dropout is guaranteed at a maximum of 1.4V at maximum output current. Its low dropout voltage and fast transient response make it ideal for low voltage microprocessor applications. Internal thermal limiting provides protection against any overload condition that would create excessive junction temperatures. Features • Dropout Voltage 1.2V at 800mA Output Current • Fast Transient Response • Line Regulation typically at 0.015% • Load Regulation typically at 0.1% • Internal thermal limiting • Adjustable Output Voltage or Fixed 2.5V, 2.85V, 3.3V, 5V • Standard 3-Pin Power Packages Applications • SCSI-2 Active Terminator • Post Regulator for Switching Supply • Battery Chargers • Constant-Current Regulators • PC Add-On Card Functional Block Diagram VIN Current Amp Mechanical Data Case: TO-220AB, TO-263AB (D2PAK), TO-252 (DPAK) and SOT-223 High temperature soldering guaranteed: 260°C/10 seconds at terminals VREF 1.25V 55µA + + GM -- Thermal Limit Current Limit VOUT For fixed voltage device ADJ GND Case outlines are on the back page Document Number 74802 20-Feb-02 www.vishay.com 1 GS1117 Vishay Semiconductors formerly General Semiconductor Maximum Ratings and Thermal Characteristics Parameter Vin Pin to ADJ/GND Pin Thermal Resistance – Junction to Case TO-220AB TO-252 TO-263AB SOT-223 Operating Junction Temperature Range Storage Temperature Range (TA = 25°C unless otherwise noted) Symbol Vin Value 7 3.0 8.0 3.0 15.0 0 to +125 – 65 to 150 Unit V RθJC °C/W TJ Tstg (2) °C °C Electrical Characteristics (1) Parameter Reference Voltage TJ = 25°C , VIN = 5V, Io = 10mA unless otherwise noted. Symbol VREF Test Conditions TJ = 25°C 0°C ≤ TJ ≤ 125°C 2.65V ≤ VIN ≤ 7V 10mA ≤ Io ≤ 800mA GS1117-2.5, VIN = 5V GS1117-2.85, VIN = 5V GS1117-3.3, VIN = 5V GS1117-5, VIN = 7V GS1117 0°C ≤ TJ ≤ 125°C 2.65V ≤ VIN ≤ 7V 10mA ≤ Io ≤ 800mA 2.65V ≤ VIN ≤ 7V TJ = 25°C 0°C ≤ TJ ≤ 125°C 10mA ≤ Io ≤ 800mA TJ = 25°C 0°C ≤ TJ ≤ 125°C 0°C ≤ TJ ≤ 125°C Io = 800mA Io = 500mA Io = 100mA Min 1.238 1.225 Typ 1.250 1.250 Max 1.262 1.275 Unit V V Output Voltage VOUT 2.48 2.82 3.26 4.95 0.98VN 2.5 2.85 3.30 5.00 VN 2.53 2.88 3.33 5.05 1.02VN V V V V V Line Regulation REGline 0.015 0.02 0.1 0.2 1.2 1.19 1.15 0.2 0.2 0.3 0.4 1.4 1.35 1.30 % VO % VO % VO % VO V V V Load Regulation REGload Dropout Voltage VDROP Notes: (1) All parameters, except nominal output voltage are specified for the variable voltage version, allowing a wider Vin Range. The specified limits also apply for the fixed voltage versions over the allowable input voltage range: GS1117-2.5 (3.9V -7.0V), GS1117-2.85 (4.25V - 7.0V), GS1117 - 3.3 (4.75V - 7.0V), GS1117-5 (6.4V - 7.0V). (2) To maintain the specified junction temperatures, low duty cycle pulse testing is required for most parameters. www.vishay.com 2 Document Number 74802 20-Feb-02 GS1117 Vishay Semiconductors formerly General Semiconductor Electrical Characteristics (1) Parameter Output Current Adjust Pin Current TJ = 25°C (2) , VIN = 5V, Io = 10mA unless otherwise noted. Symbol Io Iadj Test Conditions 0°C ≤ TJ ≤ 125°C 2.65 ≤ Vin ≤ 7V 10mA ≤ Io ≤ 800mA 0°C ≤ TJ ≤ 125°C 2.65 ≤ Vin ≤ 7V 10mA ≤ Io ≤ 800mA 0°C ≤ TJ ≤ 125°C Io = 0.5A 0°C ≤ TJ ≤ 125°C 0°C ≤ TJ ≤ 125°C 0°C ≤ TJ ≤ 125°C 10HZ ≤ f ≤ 10 kHZ f = 120 HZ, CO = 25µF Cadj = 25µF TA = 25°C, 30ms Pulse TA = 125°C, 1000 Hrs Min 0.85 Typ Max Unit A 55 120 µA Adjust Pin Current Change ∆Iadj 0.2 5 µA Temperature Stability Minimum Load Current Adjustable Version Quiescent Current Fixed Voltage Version RMS Output Noise Ripple Rejection Ratio Thermal Regulation Long Term Stability TS ILMIN IQ N RR RTH 0.8 3 10 0.003 60 68 0.02 0.3 0.05 10 14 %VO mA mA %VO dB %/W %VO Notes: (1) All parameters, except nominal output voltage are specified for the variable voltage version, allowing a wider Vin Range. The specified limits also apply for the fixed voltage versions. (2) To maintain the specified junction temperatures, low duty cycle pulse testing is required for most parameters. Typical Application Circuit VIN 5V 3 GS1117-2.5 GS1117-2.85 GS1117-3.3 GS1117-5 1 2 VIN 5V 3 GS1117 1 ADJ 2 R1 125Ω 1% R2 205Ω 1% VOUT 3.3V VOUT VREF C1 10µF + + C2 10µF C1 10µF + + C2 10µF Fixed Voltage Regulator Adjustable Voltage Regulator Notes: VREF = VOUT – VADJ = 1.25V (typ.) VOUT = VREF x (1+R2/R1) + IADJ x R2 IADJ = 55µA (typ.) (1) C1 needed if device is far away from filter capacitors (2) C2 required for stability Document Number 74802 20-Feb-02 www.vishay.com 3 GS1117 Vishay Semiconductors formerly General Semiconductor Ratings and Characteristic Curves (TA = 25°C unless otherwise noted) Fig. 1 – Dropout Voltage 1.30 1.6 Fig. 2 – Dropout Voltage v.s. Temperature IOUT = 800mA Minimum Differential Voltage (V) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0 200 400 600 TJ = 0°C TJ = 50°C TJ = 125°C 1.25 Dropout Voltage (V) 1.20 1.15 1.10 1.05 800 1000 0 20 40 60 80 100 120 140 Output Current (mA) Ambient Temperature (°C) Fig. 3 – Minimum Load Current (Adjustable Version) 5 100 Fig. 4 – Adjust Pin Current Minimum Operating Current (mA) TJ = 125°C Adjust Pin Current (µA) 4 80 3 TJ = 25°C 2 TJ = 0°C 60 40 1 20 0 1 2 3 4 5 6 0 --50 --25 0 25 50 75 100 125 Input / Output Differential Voltage (V) Temperature (°C) Fig. 5 – Temperature Stability 1.6 IOUT = 0.5A 1.2 80 70 Fig. 6 – Ripple Rejection (with Cadj 25µF) COUT = 25µF Output Voltage Deviation (%) 0.8 0.4 0.0 --0.4 --0.8 --1.2 --1.6 --20 0 20 40 60 80 100 120 140 Ripple Rejection (dB) 60 50 40 30 20 10 COUT = 10µF COUT = 25µF COUT = 10µF 100 1K 10K 100K 1M Temperature (°C) www.vishay.com 4 Frequency (Hz) Document Number 74802 20-Feb-02 GS1117 Vishay Semiconductors formerly General Semiconductor Ratings and Characteristic Curves (TA = 25°C unless otherwise noted) Fig. 7 – Load Transient Response 0.1 Fig. 8 – Line Transient Response Output Voltage (mV, AC) 50 0 --50 --100 COUT = 10µF (Tantalum) VOUT = 3.3V Output Voltage (V, AC) 0.05 0 --0.05 --0.1 VIN = 5V CIN = 1µF COUT = 10µF (Tantalum) VOUT = 3.3V Load Current Input Voltage (V) 0.4A 0.1A 7.0 6.0 0 40 80 120 160 200 0 10 20 30 40 50 Time (µs) Time (µs) Ordering Information GS1117 Cxx-xxx Output Voltage Default: Adj. 2.5: 2.5V 2.85: 2.85V 3.3: 3.3V 5: 5.0V Package Type ST: SOT-223 T: TO-220 M: TO-263 E: TO-252 Document Number 74802 20-Feb-02 www.vishay.com 5 GS1117 Vishay Semiconductors formerly General Semiconductor Case Outlines SOT-223 6.80 6.30 3.15 2.90 TO-252 (DPAK) 6.73 6.35 2.38 2.19 0.58 0.46 Top View 5.46 5.21 3.70 3.30 7.30 6.70 5.59 5.33 10.42 9.40 1 2 3 1 0.80 0.60 2 3 0.88 0.64 1.80 Max. 0.12 0.02 2.30 Typ. 0.91 Min. 0.35 0.24 0.51 (min.) 2.28 (TYP.) 1.27 1.02 13° ±3° Dimensions in millimeters TO-263 10.29 9.65 4.83 4.06 1.40 1.14 3.42 2.54 10.66 9.66 TO-220 4.08 3.54 4.82 3.56 1.39 0.51 6.85 5.85 1.40 (max.) 9.66 8.63 15.88 16.51 14.23 1 2 3 14.60 1.40 1.14 1.00 0.50 2.54 (TYP.) 2.80 2.28 0.7 (max.) 6.35 Max. 14.73 12.70 2.79 2.29 1.77 1.15 1.01 (with plating) 0.38 (with plating) 1.14 0.31 2.92 2.04 www.vishay.com 6 Document Number 74802 20-Feb-02