HFA32PA120CPBF_11

VS-HFA32PA120CPbF Vishay Semiconductors HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A FEATURES Base common cathode 2 • Ultrafast and ultrasoft recovery • Very low IRRM and Qrr • Compliant to RoHS Directive 2002/95/EC • Designed and qualified for industrial level BENEFITS • • • • • Reduced RFI and EMI Reduced power loss in diode and switching transistor Higher frequency operation Reduced snubbing Reduced parts count TO-247AC 1 3 Anode Anode 2 1 2 Common cathode DESCRIPTION VS-HFA32PA120CPbF is a state of the art ultrafast recovery diode. Employing the latest in epitaxial construction and advanced processing techniques it features a superb combination of characteristics which result in performance which is unsurpassed by any rectifier previously available. With basic ratings of 1200 V and 16 A per leg continuous current, the VS-HFA32PA120CPbF is especially well suited for use as the companion diode for IGBTs and MOSFETs. In addition to ultrafast recovery time, the HEXFRED® product line features extremely low values of peak recovery current (IRRM) and does not exhibit any tendency to “snap-off” during the tb portion of recovery. The HEXFRED features combine to offer designers a rectifier with lower noise and significantly lower switching losses in both the diode and the switching transistor. These HEXFRED advantages can help to significantly reduce snubbing, component count and heatsink sizes. The HEXFRED VS-HFA32PA120CPbF is ideally suited for applications in power supplies and power conversion systems (such as inverters), motor drives, and many other similar applications where high speed, high efficiency is needed. PRODUCT SUMMARY Package IF(AV) VR VF at IF trr (typ.) TJ max. Diode variation TO-247AC 2 x 16 A 1200 V 3.0 V 30 ns 150 °C Single die ABSOLUTE MAXIMUM RATINGS PARAMETER Cathode to anode voltage Maximum continuous forward current Single pulse forward current Maximum repetitive forward current Maximum power dissipation Operating junction and storage temperature range per leg per device SYMBOL VR IF IFSM IFRM PD TJ, TStg TC = 25 °C TC = 100 °C TC = 100 °C TEST CONDITIONS VALUES 1200 16 32 190 64 151 60 - 55 to + 150 °C W A UNITS V Document Number: 94073 Revision: 23-May-11 For technical questions within your region, please contact one of the following: www.vishay.com DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com 1 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF Vishay Semiconductors HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A ELECTRICAL SPECIFICATIONS PER LEG (TJ = 25 °C unless otherwise specified) PARAMETER Cathode to anode breakdown voltage SYMBOL VBR IR = 100 μA I F = 16 A Maximum forward voltage VFM I F = 32 A IF = 16 A, TJ = 125 °C Maximum reverse leakage current Junction capacitance Series inductance IRM CT LS VR = VR rated TJ = 125 °C, VR = 0.8 x VR rated VR = 200 V See fig. 2 See fig. 3 See fig. 1 TEST CONDITIONS MIN. 1200 TYP. 2.5 3.2 2.3 0.75 375 27 8.0 MAX. 3.0 3.93 2.7 20 2000 40 μA pF nH V UNITS Measured lead to lead 5 mm from package body DYNAMIC RECOVERY CHARACTERISTICS PER LEG (TJ = 25 °C unless otherwise specified) PARAMETER Reverse recovery time See fig. 5, 10 Peak recovery current See fig. 6 Reverse recovery charge See fig. 7 Peak rate of fall of recovery current during tb See fig. 8 SYMBOL trr trr1 trr2 IRRM1 IRRM2 Qrr1 Qrr2 dI(rec)M/dt1 dI(rec)M/dt2 TEST CONDITIONS IF = 1.0 A, dIF/dt = 200 A/μs, VR = 30 V TJ = 25 °C TJ = 125 °C TJ = 25 °C TJ = 125 °C TJ = 25 °C TJ = 125 °C TJ = 25 °C TJ = 125 °C IF = 16 A dIF/dt = 200 A/μs VR = 200 V MIN. TYP. 30 90 164 5.8 8.3 260 680 120 76 MAX. 135 245 10 15 675 1838 A/μs A ns UNITS nC THERMAL - MECHANICAL SPECIFICATIONS PARAMETER Lead temperature Thermal resistance, junction to case Thermal resistance, junction to ambient Thermal resistance, case to heatsink Weight Mounting torque Marking device Case style TO-247AC (JEDEC) SYMBOL Tlead RthJC RthJA RthCS Typical socket mount Mounting surface, flat, smooth and greased TEST CONDITIONS 0.063" from case (1.6 mm) for 10 s MIN. 6.0 (5.0) TYP. 0.50 2.0 0.07 MAX. 300 0.83 80 12 (10) g oz. kgf · cm (lbf · in) K/W UNITS °C HFA32PA120C www.vishay.com 2 For technical questions within your region, please contact one of the following: Document Number: 94073 DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com Revision: 23-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF HEXFRED® Vishay Semiconductors Ultrafast Soft Recovery Diode, 2 x 16 A IF - Instantaneous Forward Current (A) 1000 1000 TJ = 150 °C IR - Reverse Current (µA) 100 TJ = 125 °C 10 10 TJ = 150 °C TJ = 125 °C TJ = 25 °C 1 TJ = 25 °C 0.1 1 0.1 0 2 4 6 8 0.01 0 94073_02 200 400 600 800 1000 1200 94073_01 VFM - Forward Voltage Drop (V) Fig. 1 - Maximum Forward Voltage Drop vs. Instantaneous Forward Current VR - Reverse Voltage (V) Fig. 2 - Typical Reverse Current vs. Reverse Voltage 1000 CT - Junction Capacitance (pF) 100 TJ = 25 °C 10 1 0 94073_03 10 100 1000 10 000 VR - Reverse Voltage (V) Fig. 3 - Typical Junction Capacitance vs. Reverse Voltage 1 ZthJC - Thermal Response 0.1 Single pulse (thermal resistance) D = 0.50 D = 0.20 D = 0.10 D = 0.05 D = 0.02 D = 0.01 PDM t1 t2 Notes: 1. Duty factor D = t1/t2 2. Peak TJ = PDM x ZthJC + TC 0.01 0.00001 0.0001 0.001 0.01 0.1 1 10 100 94073_04 t1 - Rectangular Pulse Duration (s) Fig. 4 - Maximum Thermal Impedance ZthJC Characteristics Document Number: 94073 Revision: 23-May-11 For technical questions within your region, please contact one of the following: www.vishay.com DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com 3 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF Vishay Semiconductors HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A 270 VR = 200 V TJ = 125 °C TJ = 25 °C IF = 16 A IF = 8 A 1600 1400 1200 VR = 200 V TJ = 125 °C TJ = 25 °C IF = 16 A IF = 8 A 220 Qrr (nC) trr (ns) 170 1000 800 600 400 120 70 200 20 100 94073_05 1000 0 100 94073_07 1000 dIF/dt (A/µs) dIF/dt (A/µs) Fig. 5 - Typical Reverse Recovery Time vs. dIF/dt (Per Leg) Fig. 7 - Typical Stored Charge vs. dIF/dt (Per Leg) 30 25 20 VR = 200 V TJ = 125 °C TJ = 25 °C 10 000 VR = 200 V TJ = 125 °C TJ = 25 °C IF = 16 A IF = 8 A dI(rec)M/dt (A/µs) 1000 Irr (A) IF = 16 A IF = 8 A 1000 15 10 5 0 100 100 10 100 94073_08 1000 94073_06 dIF/dt (A/µs) dIF/dt (A/µs) Fig. 6 - Typical Recovery Current vs. dIF/dt (Per Leg) Fig. 8 - Typical dI(rec)M/dt vs. dIF/dt (Per Leg) www.vishay.com 4 For technical questions within your region, please contact one of the following: Document Number: 94073 DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com Revision: 23-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF HEXFRED® Vishay Semiconductors Ultrafast Soft Recovery Diode, 2 x 16 A VR = 200 V 0.01 Ω L = 70 μH D.U.T. dIF/dt adjust D G IRFP250 S Fig. 9 - Reverse Recovery Parameter Test Circuit (3) IF 0 trr ta tb Qrr (2) (4) IRRM 0.5 IRRM dI(rec)M/dt (5) 0.75 IRRM (1) dIF/dt (1) dIF/dt - rate of change of current through zero crossing (2) IRRM - peak reverse recovery current (3) trr - reverse recovery time measured from zero crossing point of negative going IF to point where a line passing through 0.75 IRRM and 0.50 IRRM extrapolated to zero current. (4) Qrr - area under curve defined by trr and IRRM Qrr = trr x IRRM 2 (5) dI(rec)M/dt - peak rate of change of current during tb portion of trr Fig. 10 - Reverse Recovery Waveform and Definitions Document Number: 94073 Revision: 23-May-11 For technical questions within your region, please contact one of the following: www.vishay.com DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com 5 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-HFA32PA120CPbF Vishay Semiconductors HEXFRED® Ultrafast Soft Recovery Diode, 2 x 16 A ORDERING INFORMATION TABLE Device code VS1 HF 2 - A 3 32 4 PA 5 120 6 C 7 PbF 8 1 2 3 4 5 6 7 8 Vishay Semiconductors product HEXFRED® family Electron irradiated Current rating (32 = 32 A) PA = TO-247AC Voltage rating: (120 = 1200 V) Circuit configuration C = Common cathode - PbF = Lead (Pb)-free LINKS TO RELATED DOCUMENTS Dimensions Part marking information www.vishay.com/doc?95223 www.vishay.com/doc?95226 www.vishay.com 6 For technical questions within your region, please contact one of the following: Document Number: 94073 DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com Revision: 23-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Outline Dimensions www.vishay.com DIMENSIONS in millimeters and inches (3) B (2) R/2 Q 2xR (2) 1 (5) L1 C L See view B 2 x b2 3xb 0.10 M C A M 2x e b4 A1 C A (4) E1 0.01 M D B M View A - A 2 3 E N S A2 A D2 A (6) Ø P Ø K M DBM A (Datum B) FP1 Vishay Semiconductors D D Thermal pad 4 D1 (4) Planting (b1, b3, b5) Base metal D DE E C C Lead assignments Diodes 1. - Anode/open 2. - Cathode 3. - Anode (c) c1 (b, b2, b4) (4) Section C - C, D - D, E - E View B SYMBOL A A1 A2 b b1 b2 b3 b4 b5 c c1 D D1 MILLIMETERS MIN. MAX. 4.65 5.31 2.21 2.59 1.50 2.49 0.99 1.40 0.99 1.35 1.65 2.39 1.65 2.37 2.59 3.43 2.59 3.38 0.38 0.86 0.38 0.76 19.71 20.70 13.08 - INCHES MIN. MAX. 0.183 0.209 0.087 0.102 0.059 0.098 0.039 0.055 0.039 0.053 0.065 0.094 0.065 0.094 0.102 0.135 0.102 0.133 0.015 0.034 0.015 0.030 0.776 0.815 0.515 - NOTES SYMBOL D2 E E1 e FK L L1 N P P1 Q R S 3 4 MILLIMETERS MIN. MAX. 0.51 1.30 15.29 15.87 13.72 5.46 BSC 2.54 14.20 16.10 3.71 4.29 7.62 BSC 3.56 3.66 6.98 5.31 5.69 4.52 5.49 5.51 BSC INCHES MIN. MAX. 0.020 0.051 0.602 0.625 0.540 0.215 BSC 0.010 0.559 0.634 0.146 0.169 0.3 0.14 0.144 0.275 0.209 0.224 1.78 0.216 0.217 BSC NOTES 3 Notes (1) Dimensioning and tolerancing per ASME Y14.5M-1994 (2) Contour of slot optional (3) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the outermost extremes of the plastic body (4) Thermal pad contour optional with dimensions D1 and E1 (5) Lead finish uncontrolled in L1 (6) Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154") (7) Outline conforms to JEDEC outline TO-247 with exception of dimension c Revision: 16-Jun-11 Document Number: 95223 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1