NMM0207B01009KBP00

NMM0207SI Vishay Draloric Metal Film, Cylindrical, Fusible Resistors FEATURES • Fusible resistor for constant current designed for overload protection • High positive temperature coefficient • Flame retardant coating • Defined switch-off behaviour • Pure tin termination on nickel barrier, plated on fress fit steel caps • Compatible with lead (Pb)-free and lead containing soldering processes • Lead (Pb)-free and RoHS compliant STANDARD ELECTRICAL SPECIFICATIONS MODEL NMM0207SI NMM0207SI POWER RATING1) P70 W 0.35 0.35 TEMPERATURE COEFFICIENT ppm/K + 4500 (± 500) + 4500 (± 500) TOLERANCE % ± 5, ± 10, ± 20 ± 10, ± 20 RESISTANCE RANGE Ω 1R0 - 47R R10 - R91 E-SERIES 12 - 24 12 Note 1. Permissible dissipation depends on the maximum temperature at the solder point, the component placement density and the substrate material. • Marking: additional 5th band black; According to IEC 60062; see also datasheet “surface mount resistor marking” (document number: 20020) TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70 °C Minimum Overload to Fuse Time to Fuse (max) Max. applicable Voltage after Fusing Thermal Resistance2) Category Temperature Range Failure Rate Weight/1000 pcs Note 2. Based on measurements on test board acc. to EN 140400. UNIT W W s V K/W °C 10-9/h g NMM0207SI 0.35 1.5 30 85 ≤ 220 - 55 to + 125 < 30 71 PART NUMBER AND PRODUCT DESCRIPTION3) PART NUMBER4): NMM0207B01008JBP N MODEL/SIZE NMM0207 M M 0 2 0 7 TC B 0 1 VALUE 0 0 8 J B P 0 0 SPECIAL up to 2 digits 00 = standard SPECIAL CHARACTER B = SI Fusible TOLERANCE J=±5% K = ± 10 % M = ± 20 % PACKING5) BP BS 0 = neutral see data sheet for TC value 3 digit value 1 digit multiplier MULTIPLIER 7 = *10-3 8 = *10-2 9 = *10-1 1R0 PRODUCT DESCRIPTION: NMM0207SI 1R0 5 % BP NMM0207SI MODEL NMM0207SI 5% TOLERANCE ±5% ± 10 % ± 20 % BP PACKING5) BP BS RESISTANCE VALUE 1R0 = 1 Ω R22 = 0.22 Ω Note 3. Products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER. 4. The PART NUMBER is shown to facilitate the introduction of a unified part numbering system. Currently, this PART NUMBER is applicable in the Americas only. 5. Please refer to table PACKING, see below. www.vishay.com 56 For technical questions contact: ff3bresistors@vishay.com Document Number: 20001 Revision: 15-Feb-06 NMM0207SI Metal Film Cylindrical Resistors DIMENSIONS MODEL NMM0207SI DIMENSIONS [in millimeters] Dmax 2.2 d* D - 0.4 L 5.8- 0.3 A max 1.2 A min 0.6 Vishay Draloric * d measured in the middle of the resistor SOLDER PAD DIMENSIONS [in millimeters] MODEL NMM0207SI REFLOW SOLDERING WAVE SOLDERING a 1.8 b 2.5 l 2.9 a 2.4 b 2.5 l 2.8 PACKING MODEL DIAMETER NMM0207SI 180 mm/7" 330 mm/13" BLISTER TAPE ON REEL ACC. IEC 60286-3 PIECES/REEL 1500 7500 CODE BP BS Further information about PACKING, see also datasheet mount packing” “surfaceresistor (document 20014). number: Power Rating P in % Fusing Time in s 120 100 80 60 40 20 0 - 55 50 40 30 20 10 7 5 4 3 2 1 - 25 0 25 50 Derating PERFORMANCE TEST Endurance Test at 70 °C IEC 60115-1, 4.25.1 Endurance at UCT IEC 60115-1, 4.25.3 Overload Test IEC 60115-1, 4.13 Thermal Shock IEC 60115-1, 4.19 and IEC 60068-2-14 Damp Heat Steady State IEC 60115-1, 4.24 and IEC 60068-2-78 Resistance to Soldering Heat IEC 60115-1, 4.18 and IEC 60068-2-58 70 75 100 125 1 2 3 4 5 6 7 8 9 10 Power in W Ambient Temp in °C Fusing Performance CONDITIONS OF TEST 1000 hours at 70 °C, 1.5 hours "ON", 0.5 hours "OFF" 1000 hours at 125 °C without load Short time overload for 2 seconds Rapid change between upper and lower category temperature, 5 cycles 56 days at 40 °C and 93 % relative humidity 10 seconds at 260 °C solder bath temperature REQUIREMENTS ≤2% ≤2% ≤2% ≤2% ≤2% ≤1% Document Number: 20001 Revision: 15-Feb-06 For technical questions contact: ff3bresistors@vishay.com www.vishay.com 57 NMM0207SI Vishay Draloric Metal Film Cylindrical, Fusible Resistors SOLDERING INFORMATION • For reflow soldering only • Board has to be thoroughly cleaned after soldering. All flux materials must be completely removed APPLICABLE SPECIFICATION • EN 60115-1 www.vishay.com 58 For technical questions contact: ff3bresistors@vishay.com Document Number: 20001 Revision: 15-Feb-06 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1