PE30MBFJ204MAB

PE30 Vishay Sfernice Fully Sealed Container Cermet Potentiometer Military and Professional Grade FEATURES • High power rating (3 W at 70 °C) • Low temperature coefficient (150 ppm/°C typical) • Full sealing • Use of faston 2.86 connections • Tests according to CECC 41 000 • Wires and connectors available • Custom design on request RoHS COMPLIANT DIMENSIONS in millimeters (inches) ± 0.5 (± 0.02) PE30L 8 (0.31) 20 (0.79) max. 13 (0.51) max. 12 (0.47) 14 Wrench Thread M10 x 0.75 Ø6 (0.24) a 76° c R 5.2 (0.20) FG = 16 (0.63) Ø 19.7 (0.78) FL = 25 (0.99) FR = 50 (1.97) 0.5 (0.02) 2.85 (0.11) b 3 (0.12) PE30LL: LPRP - Locating Peg 3 (0.12) Ø 1.8 (0.07) 0.8 (0.3) Ø 10.5 (0.41) 12.5 (0.49) 9.2 (0.36) Ø 3.5 (0.14) 8.8 (0.35) 3 (0.12) 2.3 (0.9) PANEL MOUNT PE30ME: Panel Sealed 23 (0.91) max. 16 (0.63) max. Ø 1.2 (0.05) 0.7 (0.03) Ø 1 (0.4) Flats located Sealing Ring Slot 1 x 1.8 Deep Ø6 (0.24) 8 ± 0.2 (0.31 ± 0.01) Ø 10.5 (0.41) Ø 19.7 (0.78) 9 (0.35) FD = 13 (0.61) FJ = 22 (0.87) FP = 47 (1.85) PANEL MOUNT Document Number: 51037 Revision: 04-Sep-08 For technical questions, contact: sfer@vishay.com See also: Application notes www.vishay.com 131 PE30 Vishay Sfernice Fully Sealed Container Cermet Potentiometer Military and Professional Grade ELECTRICAL SPECIFICATIONS Resistive Element Electrical Travel Linear Law Resistance Range Logarithmic Laws Standard Series E3 Standard Tolerance On Request Linear 100 Cermet 270° ± 10 ° 22 Ω to 10 MΩ 100 Ω to 2.2 MΩ 1 - 2.2 - 4.7 and on request 1 - 2 - 5 ± 20 % ± 10 % to ± 5 % A % TOTAL RESISTANCE CIRCUIT DIAGRAM Varation Law a (1) b (2) cw c (3) 80 60 40 20 0 F A L 0 20 40 60 80 100 % CLOCKWISE SHAFT ROTATION 3 LIN. LAW A Linear 3 W at 70 °C Power Rating Logarithmic 1.5 W at 70 °C POWER IN W 2 1 LOG. LAW L and F 0 0 20 40 60 70 80 100 120 140 AMBIENT TEMPERATURE IN °C Temperature Coefficient (Typical) Limiting Element Voltage Contact Resistance Variation End Resistance (Typical) Dielectric Strength (RMS) Insulation Resistance (300 VDC) Independent Linearity (Typical) ± 150 ppm/°C 300 V 3 % Rn or 3 Ω 1Ω 2500 V 105 MΩ ±5% www.vishay.com 132 For technical questions, contact: sfer@vishay.com Document Number: 51037 Revision: 04-Sep-08 Fully Sealed Container Cermet Potentiometer Military and Professional Grade STANDARD RESISTANCE ELEMENT DATA STANDARD RESISTANCE VALUES Ω 22 47 100 220 470 1K 2.2K 4.7K 10K 22K 47K 100K 220K 470K 1M 2.2M 4.7M 10M LINEAR LAW MAX. POWER AT 70 °C W 3 3 3 3 3 3 3 3 3 3 1.91 0.90 0.41 0.19 0.09 0.04 0.02 0.01 MAX. WORKING VOLTAGE V 8.12 11.87 17.32 25.69 37.55 57.44 81.24 118.74 173.20 256.9 300 300 300 300 300 300 300 300 MAX. CUR. THROUGH WIPER mA 369 252 173 116 79 54 37 25 17 11 6.3 3 1.36 0.63 0.30 0.13 0.06 0.03 MAX. POWER AT 70 °C W LOGS LAW MAX. WORKING VOLTAGE V PE30 Vishay Sfernice MAX. CUR. THROUGH WIPER mA TYPICAL TCR - 55 °C + 125 °C ppm/°C 1.5 1.5 1.5 1.5 1.5 1.5 0.9 0.41 0.19 0.09 38.7 57.4 83.9 122 181.6 265 300 300 300 300 38.7 26.1 17.9 12.2 8.25 5.64 3 1.36 0.63 0.30 ± 150 MECHANICAL SPECIFICATIONS Mechanical Travel Operating Torque (Typical) End Stop Torque Tightening Torque of Mounting Nut Unit Weight Terminals 3 Ncm max. 120 Ncm max. 250 Ncm max. 23 to 32 g max. e3: pure Sn 300° ± 5° 4.25 oz.-inch max. 10.51 lb oz.-inch max. 22 lb-inch max. 0.8 to 1.13 oz. ENVIRONMENTAL SPECIFICATIONS Temperature Range Climatic Category Sealing - 55 °C to 125 °C 55/125/56 Fully sealed - Container IP67 OPTIONS Special Feature Command Shaft Length is measured from the mounting surface to the free end of the shaft. The screwdriver slot is aligned with the wiper within ± 10°. Special shafts are available, in accordance to drawings supplied by customers. We recommend that customers should not machine tool shafts, in order to avoid damage. Bending or torsion of terminals should also be avoided. The panel sealing device consists of a ring located in a groove on the potentiometer face. Sealing is obtained by tightening the ring against the panel when mounting the potentiometer. Old code: PE30P Panel Sealing (PE30M) Document Number: 51037 Revision: 04-Sep-08 For technical questions, contact: sfer@vishay.com www.vishay.com 133 PE30 Vishay Sfernice OPTIONS Locating Peg (PE30LL) Fully Sealed Container Cermet Potentiometer Military and Professional Grade Location is obtained by fitting a special washer on the mounting face of the potentiometer. Old code: LPRP The shaft locking device consists of a tapered nut tightening a slotted notched washer against both bushing and shaft. DBAN tightening torque is 200 Ncm, shaft locking torque being 30 Ncm. DBAN is also available with all special types. This device is normally supplied in a separate bag. Can be pre-mounted on request. Shaft Locking (PE30LD) Assembling Method 1) 2) 14 wrench 12 wrench 6.5 15 MARKING • VISHAY trademark • Model • Ohmic Value (in Ω, kΩ or MΩ) • Tolerance (in %) • Manufacturing date code • Marking of terminals 3, and a, b, c PERFORMANCE CECC 41 301 - 002 TESTS CONDITIONS Phase A dry heat 125 °C Phase B damp heat Phase C cold - 55 °C Phase D damp heat 5 cycles 56 days 40 °C 93 % HR 25 000 cycles 1000 h at rated power 90’/30’ - ambient temp. 70 °C 5 cycles - 55 °C at + 125 °C 50 g at 11 ms 3 successive shocks in 3 directions 10 to 55 Hz 0.75 mm or 10 g during 6 hours ΔRT ΔR1-2 (%) REQUIREMENTS (%) RT R1-2 ± 10 % ± 10 % Insulation resistance: > 100 MΩ ± 10 % Contact res. variation: < 7 % Rn ± 10 % Contact res. variation: < 7 % Rn ±3% ±2% ± 10 % TYPICAL VALUES AND DRIFTS ΔRT (%) RT ± 0.5 % ΔR1-2 (%) R1-2 ±1% Climatic Sequence Long Term Damp Heat Rotational Life Load Life Rapid Temperature Change Shock ± 0.5 % ±1% Insulation resistance: > 104 MΩ ±3% Contact res. variation: < 2 % Rn ±1% Contact res. variation: < 3 % Rn ± 0.5 % ± 0.1 % ± 0.2 % Vibration ±2% ± 0.1 % ± 0.2 % www.vishay.com 134 For technical questions, contact: sfer@vishay.com Document Number: 51037 Revision: 04-Sep-08 Fully Sealed Container Cermet Potentiometer Military and Professional Grade SAP ORDERING INFORMATION (Part Number 18 digits) P E 3 0 L B F G 2 0 4 M A B PE30 Vishay Sfernice MODEL BUSHING L= M10 x 0.75 OPTION 0 = none SHAFT OHMIC VALUE TOLERANCE ± 20 % on request ± 10 % ±5% LAW A = Linear L = Clockwise logarithmic F = Clockwise inverse logarithmic PACKAGING B = Box of 10 pieces SPECIAL NUMBER (if applicable) Given by VISHAY for custom design A law = For L Bushing (= old codes:) from 22 Ω FG 16 mm, slotted = AC to 10 MΩ FL 25 mm, slotted = AM For L Bushing FR 50 mm, plain = AL D = DBAN M = Panel L and F L = LPRP sealed laws = For M Bushing B = DBAN M10 x 0.75 FD = 13 mm, slotted = AC from 100 Ω and LPRP to 2.2 MΩ FJ = 22 mm, slotted = AM A = Peg FP = 47 mm, plain = AL and DBAN For M Bushing E = Peg PART NUMBER DESCRIPTION (for information only) PE30 LPRP AC 200K 20 % A DBAN BO10 e4 CUSTOM LEAD SPECIAL SHAFT (Pb)-FREE MODEL FEATURES OPTION SHAFT VALUE TOLERANCE TAPER OPTION SPECIAL PACKAGING Document Number: 51037 Revision: 04-Sep-08 For technical questions, contact: sfer@vishay.com www.vishay.com 135 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1