SMP30

SMP11 thru SMP36A New Product Vishay General Semiconductor Surface Mount TRANSZORB® Transient Voltage Suppressors FEATURES • Very low profile - typical height of 1.0 mm • Ideal for automated placement • Available in Unidirectional • 400 W peak pulse power capability with a 10/1000 µs waveform • Excellent clamping capability • Very fast response time DO-220AA (SMP) • Low incremental surge resistance • Meets MSL level 1, per J-STD-020C • Solder Dip 260 °C, 40 seconds • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. MECHANICAL DATA Case: DO-220AA (SMP) Epoxy meets UL 94V-0 flammability rating Terminals: Matte tin plated leads, solderable per J-STD-002B and JESD22-B102D E3 suffix for commercial grade Polarity: Color band denotes cathode end MAJOR RATINGS AND CHARACTERISTICS VWM PPPM IFSM Tj max. 11 V to 36 V 400W 40 A 150 °C MAXIMUM RATINGS (TA = 25 °C unless otherwise noted) PARAMETER Peak pulse power dissipation with a 10/1000 µs waveform Peak pulse current with a 10/1000 µs waveform (1) Peak forward surge current 10 ms single half sine-wave Maximum instantaneous forward voltage at 25 A (3) Operating junction and storage temperature range Note: (1) Non-repetitive current pulse, per Fig. 3 and derated above TA = 25 °C per Fig. 2 (2) Mounted on 0.2 x 0.2" (5.0 x 5.0 mm) copper pads to each terminal (3) Pulse test: 300 µs pulse width, 1 % duty cycle (2) (1,2) SYMBOL (Fig. 1) PPPM IPPM IFSM VF TJ, TSTG VALUE 400 see table next page 40 2.5 - 55 to + 150 UNIT W A A V °C Document Number 88481 26-Jul-06 www.vishay.com 1 SMP11 thru SMP36A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted) DEVICE MARKING CODE AY AZ BD BE BF BG BH BK BL BM BN BP BQ BR BS BT BU BV BW BX BY BZ CD CE CF CG CH CK CL CM CN CP BREAKDOWN VOLTAGE V(BR) AT IT (1) (V) MIN SMP11 SMP11A SMP12 SMP12A SMP13 SMP13A SMP14 SMP14A SMP15 SMP15A SMP16 SMP16A SMP17 SMP17A SMP18 SMP18A SMP20 SMP20A SMP22 SMP22A SMP24 SMP24A SMP26 SMP26A SMP28 SMP28A SMP30 SMP30A SMP33 SMP33A SMP36 SMP36A Note: (1) V(BR) measured after IT applied for 300 µs, IT = suqare wave pulse or equivalent (2) Surge current waveform per Fig. 3 and derate per Fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 12.2 12.2 13.3 13.3 14.4 14.4 15.6 15.6 16.7 16.7 17.8 17.8 18.9 18.9 20.0 20.0 22.2 22.2 24.4 24.4 26.7 26.7 28.9 28.9 31.1 31.1 33.3 33.3 36.7 36.7 40.0 40.0 MAX 14.9 13.5 16.3 14.7 17.6 15.9 19.1 17.2 20.4 18.5 21.8 19.7 23.1 20.9 24.4 22.1 27.1 24.5 29.8 26.9 32.6 29.5 35.3 31.9 38.0 34.4 40.7 36.8 44.9 40.6 48.9 44.2 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 20 20 22 22 24 24 26 26 28 28 30 30 33 33 36 36 TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM ID (µA) (3) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 MAXIMUM PEAK PULSE SURGE CURRENT IPPM (A) (2) 19.9 22.0 18.2 20.1 16.8 18.6 15.5 17.2 14.9 16.4 13.9 15.4 13.1 14.5 12.4 13.7 11.2 12.3 10.2 11.3 9.3 10.3 8.6 9.5 8.0 8.8 7.5 8.3 6.8 7.5 6.2 6.9 MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) 20.1 18.2 22.0 19.9 23.8 21.5 25.8 23.2 26.9 24.4 28.8 26.0 30.5 27.6 32.2 29.2 35.8 32.4 39.4 35.5 43.0 38.9 46.6 42.1 50.0 45.4 53.5 48.4 59.0 53.3 64.3 58.1 DEVICE TYPE ORDERING INFORMATION PREFERRED P/N SMP11A-E3/84A SMP11A-E3/85A UNIT WEIGHT (g) 0.024 0.024 PREFERRED PACKAGE CODE 84A 85A BASE QUANTITY 3000 10000 DELIVERY MODE 7" Diameter Plastic Tape & Reel 13" Diameter Plastic Tape & Reel www.vishay.com 2 Document Number 88481 26-Jul-06 SMP11 thru SMP36A Vishay General Semiconductor RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 10 150 Non-repetitive Pulse Waveform shown in Fig. 3 TA = 25 °C TJ = 25 °C Pulse Width (td) is defined as the point where the peak current decays to 50 % of IPPM IPPM - Peak Pulse Current, % IRSM PPPM - Peak Pulse Power (kW) tr = 10 µsec Peak Value IPPM 100 1 Half Value - IPP 2 IPPM 50 10/1000 µsec Waveform as defined by R.E.A. 0.2 x 0.2" (0.5 x 0.5 mm) Copper Pad Areas 0.1 0.1 µs td 0 1.0 µs 10 µs 100 µs 1.0 ms 10 ms 0 1.0 2.0 3.0 4.0 td - Pulse Width (s) t - Time (ms) Figure 1. Peak Pulse Power Rating Curve Figure 3. Pulse Waveform Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage (%) 100 10000 75 CJ - Junction Capacitance (pF) Tj = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 1000 Measured at Zero Bias 50 100 25 Measured at Stand-Off Voltage, VWM 0 0 25 50 75 100 125 150 175 200 10 10 100 TJ = Initial Temperature (°C) VWM - Reverse Stand-off Voltage (V) Figure 2. Pulse Derating Curve Figure 4. Typical Junction Capacitance PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-220AA (SMP) Cathode band 0.012 (0.30) REF 0.086 (2.18) 0.074 (1.88) 0.053 (1.35) 0.041 (1.05) 0.036 (0.91) 0.024 (0.61) 0.142 (3.61) 0.126 (3.19) 0.158 (4.00) 0.146 (3.70) 0.103 (2.60) 0.087 (2.20) 0.032 (0.80) 0.016 (0.40) 0.013 (0.35) 0.004 (0.10) 0.045 (1.15) 0.033 (0.85) 0.012 (0.30) 0.000 (0.00) 0.100 (2.54) 0.018 (0.45) 0.006 (0.15) 0.105 (2.67) 0.025 (0.635) 0.030 (0.762) 0.050 (1.27) Document Number 88481 26-Jul-06 www.vishay.com 3 Legal Disclaimer Notice Vishay Notice Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Document Number: 91000 Revision: 08-Apr-05 www.vishay.com 1