TPC8.2A

New Product TPC6.8 thru TPC43A Vishay General Semiconductor Surface Mount PAR® Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions FEATURES eSMP Series A ® • Junction passivation optimized design passivated anisotropic rectifier technology • TJ = 185 °C capability suitable for high reliability and automotive requirement • Very low profile - typical height of 1.1 mm 1 2 • Ideal for automated placement • Uni-direction only • Excellent clamping capability • Low incremental surge resistance • Very fast response time • Meets MSL level 1, per J-STD-020 • AEC-Q101 qualified • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC • Halogen-free according to IEC 61249-2-21 definition TO-277A (SMPC) A Anode Cathode 1 Cathode 2 PRIMARY CHARACTERISTICS VBR PPPM IFSM TJ max. 6.8 V to 43 V 1500 W 200 A 185 °C MECHANICAL DATA Case: TO-220AA (SMPC) Molding compound meets UL 94 V-0 flammability rating Base P/NHM3 - halogen-free, RoHS compliant, and automotive grade Terminals: Matte tin plated leads, solderable J-STD-002 and JESD 22-B102 HM3 suffix meets JESD 201 class 2 whisker test per TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted) PARAMETER Peak power dissipation with a 10/1000 μs waveform (fig. 3) (1)(2) (1) SYMBOL PPPM IPPM IFSM VF TJ, TSTG VALUE 1500 See next table 200 3.5 - 65 to + 185 UNIT W A A V °C Peak power pulse current with a 10/1000 μs waveform (fig. 1) Peak forward surge current 8.3 ms single half sine-wave (2) Maximum instantaneous forward voltage at 100 A (3) Operating junction and storage temperature range Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2 A (2) Measured on 8.3 ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minute maximum (3) Pulse test: 300 μs pulse width, 1 % duty cycle Document Number: 89056 Revision: 10-May-11 For technical questions within your region, please contact one of the following: www.vishay.com DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com 1 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TPC6.8 thru TPC43A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C, unless otherwise noted) DEVICE TYPE DEVICE MARKING CODE BREAKDOWN VOLTAGE VBR (1) AT IT (V) MIN. TPC6.8 TPC6.8A TPC7.5 TPC7.5A TPC8.2 TPC8.2A TPC9.1 TPC9.1A TPC10 TPC10A TPC11 TPC11A TPC12 TPC12A TPC13 TPC13A TPC15 TPC15A TPC16 TPC16A TPC18 TPC18A TPC20 TPC20A TPC22 TPC22A TPC24 TPC24A TPC27 TPC27A TPC30 TPC30A TPC33 TPC33A TPC36 TPC36A TPC39 TPC39A TPC43 TPC43A DDP DEP DFP DGP DHP DKP DLP DMP DNP DPP DQP DRP DSP DTP DUP DVP DWP DXP DYP DZP EDP EEP EFP EGP EHP EKP ELP EMP ENP EPP EQP ERP ESP ETP EUP EVP EWP EXP EYP EZP 6.12 6.45 6.75 7.13 7.38 7.79 8.19 8.65 9.0 9.5 9.9 10.5 10.8 11.4 11.7 12.4 13.5 14.3 14.4 15.2 16.2 17.1 18.0 19.0 19.8 20.9 21.6 22.8 24.3 25.7 27.0 28.5 29.7 31.4 32.4 34.2 35.1 37.1 38.7 40.9 MAX. 7.48 7.14 8.25 7.88 9.02 8.61 10.0 9.55 11.0 10.5 12.1 11.6 13.2 12.6 14.3 13.7 16.5 15.8 17.6 16.8 19.8 18.9 22.0 21.0 24.2 23.1 26.4 25.2 29.7 28.4 33.0 31.5 36.3 34.7 39.6 37.8 42.9 41.0 47.3 45.2 10 10 10 10 10 10 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 5.50 5.80 6.05 6.40 6.63 7.02 7.37 7.78 8.10 8.55 8.92 9.40 9.72 10.2 10.5 11.1 12.1 12.8 12.9 13.6 14.5 15.3 16.2 17.1 17.8 18.8 19.4 20.5 21.8 23.1 24.3 25.6 26.8 28.2 29.1 30.8 31.6 33.3 34.8 36.8 TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM IR (μA) 1500 1500 500 500 200 200 50 50 20 20 5.0 5.0 2.0 2.0 2.0 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 MAXIMUM REVERSE LEAKAGE AT VWM TJ = 150 °C ID (μA) 10 000 10 000 5000 5000 2000 2000 500 500 200 200 50 50 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 15 15 15 15 20 20 MAXIMUM PEAK PULSE SURGE CURRENT IPPM (2) (A) 139 143 128 133 120 124 109 112 100 103 92.6 96.2 86.7 89.8 78.9 82.4 68.2 70.8 63.8 66.7 56.6 59.5 51.5 54.2 47.0 49.0 43.2 45.2 38.4 40.0 34.5 36.2 31.4 32.8 28.8 30.1 26.6 27.8 24.2 25.3 MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) 10.8 10.5 11.7 11.3 12.5 12.1 13.8 13.4 15.0 14.5 16.2 15.6 17.3 16.7 19.0 18.2 22.0 21.2 23.5 22.5 26.5 25.2 29.1 27.7 31.9 30.6 34.7 33.2 39.1 37.5 43.5 41.4 47.7 45.7 52.0 49.9 56.4 53.9 61.9 59.3 Notes (1) V BR measured after IT applied for 300 μs, IT = square wave pulse or equivalent (2) Surge current waveform per fig. 3 and derated per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 www.vishay.com 2 For technical questions within your region, please contact one of the following: Document Number: 89056 DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com Revision: 10-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TPC6.8 thru TPC43A Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N TPC10AHM3/86A (1) TPC10AHM3/87A (1) UNIT WEIGHT (g) 0.10 0.10 PREFERRED PACKAGE CODE 86A 87A BASE QUANTITY 1500 6500 DELIVERY MODE 7" diameter plastic tape and reel 13" diameter plastic tape and reel Note (1) Automotive grade RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 100 150 IPPM - Peak Pulse Current, % IRSM PPPM - Peak Power (kW) TA = 25 °C Non-Repetitive Pulse Waveform shown in Fig. 3 10 tr = 10 µs Peak Value IPPM 100 TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td 0 0 1.0 2.0 3.0 4.0 1 0.1 0.1 µs 1.0 µs 10 µs 100 µs 1.0 ms 10 ms td - Pulse Width (s) t - Time (ms) Fig. 1 - Peak Pulse Power Rating Curve Fig. 3 - Pulse Waveform Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage (%) 100 10 000 VR, measured at Zero Bias 75 Junction Capacitance (pF) 1000 VR measured at Stand-Off Voltage, VWM 50 100 TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 1 10 100 25 0 0 50 100 150 200 TJ - Initial Temperature (°C) VBR - Breakdown Voltage (V) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Fig. 4 - Typical Junction Capacitance Document Number: 89056 Revision: 10-May-11 For technical questions within your region, please contact one of the following: www.vishay.com DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com 3 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 New Product TPC6.8 thru TPC43A Vishay General Semiconductor PACKAGE OUTLINE DIMENSIONS in inches (millimeters) TO-277A (SMPC) 0.187 (4.75) 0.175 (4.45) A 0.016 (0.40) 0.006 (0.15) 0.262 (6.65) 0.250 (6.35) 0.242 (6.15) 0.238 (6.05) K 2 K 1 0.171 (4.35) 0.167 (4.25) 0.146 (3.70) 0.134 (3.40) 0.087 (2.20) 0.075 (1.90) 0.047 (1.20) 0.039 (1.00) Mounting Pad Layout 0.189 (4.80) MIN. 0.189 (4.80) 0.173 (4.40) 0.155 (3.94) NOM. 0.030 (0.75) NOM. 0.268 (6.80) 0.186 (4.72) MIN. 0.049 (1.24) 0.037 (0.94) 0.084 (2.13) NOM. 0.053 (1.35) 0.041 (1.05) Conform to JEDEC TO-277A 0.050 (1.27) MIN. 0.041 (1.04) 0.055 (1.40) MIN. www.vishay.com 4 For technical questions within your region, please contact one of the following: Document Number: 89056 DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com Revision: 10-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1