TPSMC24

TPSMC6.8 thru TPSMC47A Vishay General Semiconductor Surface Mount PAR® Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions FEATURES • Junction passivation optimized design passivated anisotropic rectifier technology • TJ = 185 °C capability suitable for high reliability and automotive requirement • Available in uni-directional polarity only • 1500 W peak pulse power capability with a 10/1000 µs waveform DO-214AB (SMC) • Excellent clamping capability • Very fast response time • Low incremental surge resistance • Meets MSL level 1, per J-STD-020, LF maximum peak of 260 °C • AEC-Q101 qualified • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC MECHANICAL DATA Case: DO-214AB (SMC) Molding compound meets UL 94 V-0 flammability rating Base P/NHE3 - RoHS compliant, AEC-Q101 qualified Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 HE3 suffix meets JESD 201 class 2 whisker test Polarity: Color band denotes cathode end PRIMARY CHARACTERISTICS VBR PPPM IFSM TJ max. 6.8 V to 47 V 1500 W 200 A 185 °C TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. MAXIMUM RATINGS (TA = 25 °C unless otherwise noted) PARAMETER Peak pulse power dissipation with a 10/1000 µs waveform (1)(2) (fig. 3) Peak power pulse current with a 10/1000 µs waveform (1) (2)(3) SYMBOL PPPM IPPM IFSM VF TJ, TSTG VALUE 1500 See next table 200 3.5 - 65 to + 185 UNIT W A A V °C (fig. 1) Peak forward surge current 8.3 ms single half sine-wave (2)(3) Maximum instantaneous forward voltage at 100 A Operating junction and storage temperature range Notes (1) (2) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2 Mounted on 0.31" x 0.31" (8.0 mm x 8.0 mm) copper pads at each terminal (3) Measured on 8.3 ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minute maximum Document Number: 88407 Revision: 09-Feb-11 For technical questions within your region, please contact one of the following: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com www.vishay.com 1 TPSMC6.8 thru TPSMC47A Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted) DEVICE MARKING CODE BREAKDOWN VOLTAGE VBR (1) AT IT (V) MIN. 6.12 6.45 6.75 7.13 7.38 7.79 8.19 8.65 9.00 9.50 9.90 10.5 10.8 11.4 11.7 12.4 13.5 14.3 14.4 15.2 16.2 17.1 18.0 19.0 19.8 20.9 21.6 22.8 24.3 25.7 27.0 28.5 29.7 31.4 32.4 34.2 35.1 37.1 38.7 40.9 42.3 44.7 MAX. 7.48 7.14 8.25 7.88 9.02 8.61 10.0 9.55 11.0 10.5 12.1 11.6 13.2 12.6 14.3 13.7 16.5 15.8 17.6 16.8 19.8 18.9 22.0 21.0 24.2 23.1 26.4 25.2 29.7 28.4 33.0 31.5 36.3 34.7 39.6 37.8 42.9 41.0 47.3 45.2 51.7 49.4 TEST CURRENT IT (mA) 10.0 10.0 10.0 10.0 10.0 10.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 STAND-OFF VOLTAGE VWM (V) 5.50 5.80 6.05 6.40 6.63 7.02 7.37 7.78 8.10 8.55 8.92 9.40 9.72 10.2 10.5 11.1 12.1 12.8 12.9 13.6 14.5 15.3 16.2 17.1 17.8 18.8 19.4 20.5 21.8 23.1 24.3 25.6 26.8 28.2 29.1 30.8 31.6 33.3 34.8 36.8 38.1 40.2 MAXIMUM REVERSE LEAKAGE AT VWM IR (µA) 1000 1000 500 500 200 200 50 50 20 20 5.0 5.0 2.0 2.0 2.0 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 TJ = 150 °C MAXIMUM REVERSE LEAKAGE AT VWM ID (µA) 10000 10000 5000 5000 2000 2000 500 500 200 200 50 50 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 15 15 15 15 20 20 20 20 MAXIMUM PEAK PULSE SURGE CURRENT IPPM (2) (A) 139.0 143.0 128.0 133.0 120.0 124.0 109.0 112.0 100.0 103.0 92.6 96.2 86.7 89.8 78.9 82.4 68.2 70.8 63.8 66.7 56.6 59.5 51.5 54.2 47.0 49.0 43.2 45.2 38.4 40.0 34.5 36.2 31.4 32.8 28.8 30.1 26.6 27.8 24.2 25.3 22.1 23.1 MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) 10.8 10.5 11.7 11.3 12.5 12.1 13.8 13.4 15.0 14.5 16.2 15.6 17.3 16.7 19.0 18.2 22.0 21.2 23.5 22.5 26.5 25.2 29.1 27.7 31.9 30.6 34.7 33.2 39.1 37.5 43.5 41.4 47.7 45.7 52.0 49.9 56.4 53.9 61.9 59.3 67.8 64.8 DEVICE TYPE TPSMC6.8 TPSMC6.8A TPSMC7.5 TPSMC7.5A TPSMC8.2 TPSMC8.2A TPSMC9.1 TPSMC9.1A TPSMC10 TPSMC10A TPSMC11 TPSMC11A TPSMC12 TPSMC12A TPSMC13 TPSMC13A TPSMC15 TPSMC15A TPSMC16 TPSMC16A TPSMC18 TPSMC18A TPSMC20 TPSMC20A TPSMC22 TPSMC22A TPSMC24 TPSMC24A TPSMC27 TPSMC27A TPSMC30 TPSMC30A TPSMC33 TPSMC33A TPSMC36 TPSMC36A TPSMC39 TPSMC39A TPSMC43 TPSMC43A TPSMC47 TPSMC47A Notes (1) (2) DDP DEP DFP DGP DHP DKP DLP DMP DNP DPP DQP DRP DSP DTP DUP DVP DWP DXP DYP DZP EDP EEP EFP EGP EHP EKP ELP EMP ENP EPP EQP ERP ESP ETP EUP EVP EWP EXP EYP EZP FDP FEP VBR measured after IT applied for 300 µs, IT = square wave pulse or equivalent Surge current waveform per fig. 3 and derated per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 www.vishay.com 2 For technical questions within your region, please contact one of the following: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com Document Number: 88407 Revision: 09-Feb-11 TPSMC6.8 thru TPSMC47A Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N TPSMC6.8AHE3/57T (1) TPSMC6.8AHE3/9AT (1) Note (1) UNIT WEIGHT (g) 0.211 0.211 PREFERRED PACKAGE CODE 57T 9AT BASE QUANTITY 850 3500 DELIVERY MODE 7" diameter plastic tape and reel 13" diameter plastic tape and reel AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) 100 150 IPPM - Peak Pulse Current, % IRSM PPPM - Peak Power (kW) TA = 25 °C Non-Repetitive Pulse Waveform shown in Fig. 3 10 tr = 10 µs Peak Value IPPM TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM 100 Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td 0 0 1.0 2.0 3.0 4.0 1.0 0.31 x 0.31" (8.0 x 8.0 mm) Copper Pad Areas 0.1 0.1 µs 1.0 µs 10 µs 100 µs 1.0 ms 10 ms td - Pulse Width (s) t - Time (ms) Figure 1. Peak Pulse Power Rating Curve Figure 3. Pulse Waveform Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % 100 10 000 VR, measured at Zero Bias 75 Junction Capacitance (pF) 1000 VR measured at Stand-Off Voltage, VWM 50 100 TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 1 10 100 25 0 0 50 100 150 200 TJ - Initial Temperature (°C) VBR - Breakdown Voltage (V) Figure 2. Pulse Power or Current vs. Initial Junction Temperature Figure 4. Typical Junction Capacitance Document Number: 88407 Revision: 09-Feb-11 For technical questions within your region, please contact one of the following: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com www.vishay.com 3 TPSMC6.8 thru TPSMC47A Vishay General Semiconductor 200 Peak Forward Surge Current (A) TJ = TJ max. 8.3 ms Single Half Sine-Wave 100 50 10 1 5 10 50 100 Number of Cycles at 60 Hz Figure 5. Maximum Non-Repetitive/Peak Forward Surge Current PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-214AB (SMC) Cathode Band Mounting Pad Layout 0.185 (4.69) MAX. 0.126 (3.20) 0.114 (2.90) 0.246 (6.22) 0.220 (5.59) 0.126 (3.20) MIN. 0.280 (7.11) 0.260 (6.60) 0.012 (0.305) 0.006 (0.152) 0.103 (2.62) 0.079 (2.06) 0.060 (1.52) 0.030 (0.76) 0.008 (0.2) 0 (0) 0.320 (8.13) 0.305 (7.75) 0.060 (1.52) MIN. 0.320 (8.13) REF. www.vishay.com 4 For technical questions within your region, please contact one of the following: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com Document Number: 88407 Revision: 09-Feb-11 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1