TSOP1356SB1

VISHAY TSOP13..SB1 Vishay Semiconductors IR Receiver Modules for Remote Control Systems Description The TSOP13..SB1- series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses. 96 12581 Features • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Improved shielding against electrical field disturbance • TTL and CMOS compatibility • Output active low • Low power consumption • No occurrence of disturbance pulses at the output Parts Table Part TSOP1330SB1 TSOP1333SB1 TSOP1336SB1 TSOP1337SB1 TSOP1338SB1 TSOP1340SB1 TSOP1356SB1 30 kHz 33 kHz 36 kHz 36.7 kHz 38 kHz 40 kHz 56 kHz Carrier Frequency Special Features • Suitable burst length ≥6 cycles/burst • Enhanced immunity against all kinds of disturbance light • Improved immunity against EMI from TV picture tube Application Circuit Transmitter TSOPxxxx with TSALxxxx Circuit R1 = 100 Ω VS C1 = 4.7 µF VO +VS Block Diagram 2 25 kΩ Input PIN AGC Band Pass Demodulator VS OUT GND µC GND R1 + C1 recommended to suppress power supply disturbances. The output voltage should not be hold continuously at a voltage below VO = 3.3 V by the external circuit. 3 OUT 1 Control Circuit GND Document Number 82026 Rev. 6, 15-Oct-2002 www.vishay.com 1 TSOP13..SB1 Vishay Semiconductors Absolute Maximum Ratings Tamb = 25 °C, unless otherwise specified Parameter Supply Voltage Supply Current Output Voltage Output Current Junction Temperature Storage Temperature Range Operating Temperature Range Power Consumption Soldering Temperature (Tamb ≤ 85 °C) t ≤ 10 s, 1 mm from case (Pin 2) (Pin 2) (Pin 3) (Pin 3) Test condition Symbol VS IS VO IO Tj Tstg Tamb Ptot Tsd Value VISHAY Unit V mA V mA °C °C °C mW °C - 0.3 to + 6.0 5 - 0.3 to + 6.0 5 100 - 25 to + 85 - 25 to + 85 50 260 Electrical and Optical Characteristics Tamb = 25 °C, unless otherwise specified Parameter Supply Current (Pin 2) Supply Voltage (Pin 2) Transmission Distance Output Voltage Low (Pin 3) Irradiance (30 - 40 kHz) Ev = 0, test signal see fig.3, IR diode TSAL6200, IF = 0.4 A IOSL = 0.5 mA, Ee = 0.7 mW/m2, f = fo, test signal see fig.1 Test signal see fig.1 Test signal see fig.3 Irradiance (56 kHz) Test signal see fig.1 Test signal see fig.3 Irradiance Directivity Test signal see fig.1 Angle of half transmission distance Test condition VS = 5 V, Ev = 0 VS = 5 V, Ev = 40 klx, sunlight Symbol ISD ISH VS d VOSL Ee min Ee min Ee min Ee min Ee max ϕ1/2 30 ± 45 0.4 0.35 0.45 0.40 4.5 35 250 0.6 0.5 0.7 0.6 Min 0.8 Typ. 1.2 1.5 5.5 Max 1.5 Unit mA mA V m mV mW/m2 mW/m2 mW/m2 mW/m2 W/m2 deg Typical Characteristics (Tamb = 25°C unless otherwise specified) Ee Optical Test Signal (IR diode TSAL6200, IF=0.4 A, N=6 pulses, f=f0, T=10 ms) t po – Output Pulse Width ( ms ) 0.35 0.30 Output Pulse 0.25 0.20 0.15 0.10 0.05 0.00 0.1 16907 tpi *) T *) tpi w 6/fo is recommended for optimal function Output Signal VO VOH VOL td1 ) 1) 2) t Input Burst Duration l = 950 nm, optical test signal, fig.1 14337 3/f0 < td < 9/f0 tpi – 4/f0 < tpo < tpi + 6/f0 t tpo2 ) 1.0 10.0 100.0 1000.010000.0 Ee – Irradiance ( mW/m2 ) Figure 1. Output Function Figure 2. Pulse Length and Sensitivity in Dark Ambient Document Number 82026 Rev. 6, 15-Oct-2002 www.vishay.com 2 VISHAY TSOP13..SB1 Vishay Semiconductors Ee Optical Test Signal Ee min– Threshold Irradiance ( mW/m 2 ) 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.01 Ambient, l = 950 nm Correlation with ambient light sources: 10W/m2^1.4klx (Std.illum.A,T=2855K) 10W/m2^8.2klx (Daylight,T=5900K) 600 ms T = 60 ms Output Signal, ( see Fig.4 ) 600 ms t 94 8134 VO VOH VOL Ton Toff t 16911 0.10 1.00 10.00 100.00 E – Ambient DC Irradiance (W/m2) Figure 3. Output Function Figure 6. Sensitivity in Bright Ambient 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.1 1.0 l = 950 nm, optical test signal, fig.3 Toff Ton Ee min– Threshold Irradiance ( mW/m 2 ) Ton ,Toff – Output Pulse Width ( ms ) 1.0 2.0 f = fo f = 10 kHz 1.0 1.5 f = 1 kHz 0.5 f = 100 Hz 0.0 0.1 1.0 10.0 100.0 1000.0 10.0 100.0 1000.010000.0 16912 16910 Ee – Irradiance ( mW/m2 ) DVsRMS – AC Voltage on DC Supply Voltage (mV) Figure 4. Output Pulse Diagram Figure 7. Sensitivity vs. Supply Voltage Disturbances E e min– Threshold Irradiance ( mW/m 2 ) 1.2 E e min / E e – Rel. Responsivity 2.0 f(E) = f0 1.6 1.2 0.8 0.4 0.0 0.0 0.4 0.8 1.2 1.6 2.0 E – Field Strength of Disturbance ( kV/m ) 1.0 0.8 0.6 0.4 0.2 0.0 0.7 f = f0"5% Df ( 3dB ) = f0/10 0.9 1.1 1.3 16925 f/f0 – Relative Frequency 94 8147 Figure 5. Frequency Dependence of Responsivity Figure 8. Sensitivity vs. Electric Field Disturbances Document Number 82026 Rev. 6, 15-Oct-2002 www.vishay.com 3 TSOP13..SB1 Vishay Semiconductors VISHAY 0.7 Max. Envelope Duty Cycle 0 10 20 30 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 20 40 60 80 100 120 95 11340p2 40 1.0 0.9 0.8 f = 38 kHz, Ee = 2 mW/m2 0.7 50 60 70 80 0.6 0.6 0.4 0.2 0 0.2 0.4 drel – Relative Transmission Distance 16916 Burst Length ( number of cycles / burst ) Figure 9. Max. Envelope Duty Cycle vs. Burstlength Figure 12. Horizontal Directivity ϕx Ee min– Threshold Irradiance ( mW/m 2 ) 0.6 0.5 0.4 1.0 0.3 0.2 0.1 0.0 –30 –15 0.9 0.8 0.7 Sensitivity in dark ambient 0 10 20 30 40 50 60 70 80 0 15 30 45 60 75 90 95 11339p2 0.6 16918 Tamb – Ambient Temperature ( C ) 0.6 0.4 0.2 0 0.2 0.4 drel – Relative Transmission Distance Figure 10. Sensitivity vs. Ambient Temperature Figure 13. Vertical Directivity ϕy S ( l ) rel – Relative Spectral Sensitivity 1.2 1.0 0.8 0.6 0.4 0.2 0 750 Suitable Data Format The circuit of the TSOP13..SB1 is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpassfilter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal and disturbance signal are carrier frequency, burst length and duty cycle. The data signal should fulfill the following conditions: • Carrier frequency should be close to center frequency of the bandpass (e.g. 38 kHz). • Burst length should be 6 cycles/burst or longer. • After each burst which is between 6 cycles and 40 cycles a gap time of at least 12 cycles is necessary. • For each burst which is longer than 1.0 ms a corresponding gap time is necessary at some time in the 850 950 1050 1150 94 8408 l – Wavelength ( nm ) Figure 11. Relative Spectral Sensitivity vs. Wavelength Document Number 82026 Rev. 6, 15-Oct-2002 www.vishay.com 4 VISHAY data stream. This gap time should be at least 6 times longer than the burst. • Up to 1000 short bursts per second can be received continuously. Some examples for suitable data format are: NEC Code, Toshiba Micom Format, Sharp Code, RC5 Code, RC6 Code, R-2000 Code, RECS-80 Code. When a disturbance signal is applied to the TSOP13..SB1 it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occure. Some examples for such disturbance signals which are suppressed by the TSOP13..SB1 are: • DC light (e.g. from tungsten bulb or sunlight) • Continuous signal at 38 kHz or at any other frequency • Signals from fluorescent lamps with electronic ballast with high or low modulation ( see Figure 14 or Figure 15 ). TSOP13..SB1 Vishay Semiconductors IR Signal from fluorescent lamp with high modulation IR Signal 0 16921 5 10 Time ( ms ) 15 20 Figure 15. IR Signal from Fluorescent Lamp with high Modulation IR Signal IR Signal from fluorescent lamp with low modulation 0 16920 5 10 Time ( ms ) 15 20 Figure 14. IR Signal from Fluorescent Lamp with low Modulation Document Number 82026 Rev. 6, 15-Oct-2002 www.vishay.com 5 TSOP13..SB1 Vishay Semiconductors Package Dimensions in mm VISHAY 96 12225 Document Number 82026 Rev. 6, 15-Oct-2002 www.vishay.com 6 VISHAY Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. TSOP13..SB1 Vishay Semiconductors 2. Regularly and continuously improve the performance of our products, processes, distribution and operatingsystems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423 Document Number 82026 Rev. 6, 15-Oct-2002 www.vishay.com 7