TSOP58236

New TSOP582.., TSOP584.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Improved shielding against EMI • Supply voltage: 2.7 V to 5.5 V • Improved immunity against ambient light 19026 e3 • Insensitive to supply voltage ripple and noise • Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC MECHANICAL DATA Pinning: 1 = OUT, 2 = GND, 3 = VS DESCRIPTION The TSOP582.., TSOP584.. series are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TSOP582.. is compatible with all common IR remote control data formats. The TSOP584.. is optimized to suppress almost all spurious pulses from energy saving fluorescent lamps but will also suppress some data signals. This component has not been qualified according to automotive specifications. PARTS TABLE CARRIER FREQUENCY 30 kHz 33 kHz 36 kHz 36.7 kHz 38 kHz 40 kHz 56 kHz STANDARD APPLICATIONS (AGC2/AGC8) TSOP58230 TSOP58233 TSOP58236 TSOP58237 TSOP58238 TSOP58240 TSOP58256 TSOP58438 VERY NOISY ENVIROMENTS (AGC4) BLOCK DIAGRAM 16833_5 APPLICATION CIRCUIT 17170_7 3 33 kΩ VS 1 Input AGC Band pass Demodulator OUT R1 IR receiver VS + VS C1 OUT GND VO µC GND Transmitter with TSALxxxx 2 PIN Control circuit GND The external components R1 and C1 are optional to improve the robustnes against electrical overstress (typical values are R1 = 100 Ω, C1 = 0.1 µF). The output voltage VO should not be pulled down to a level below 1 V by the external circuit. The capacitive load at the output should be less than 2 nF. www.vishay.com 146 Circuit Document Number: 81221 Rev. 1.4, 15-Oct-08 New TSOP582.., TSOP584.. IR Receiver Modules for Remote Control Systems ABSOLUTE MAXIMUM RATINGS (1) PARAMETER Supply voltage (pin 3) Supply current (pin 3) Output voltage (pin 1) Voltage at output to supply Output current (pin 1) Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tamb ≤ 85 °C t ≤ 10 s, 1 mm from case TEST CONDITION SYMBOL VS IS VO V S - VO IO Tj Tstg Tamb Ptot Tsd VALUE - 0.3 to + 6.0 5 - 0.3 to 5.5 - 0.3 to (VS + 0.3) 5 100 - 25 to + 85 - 25 to + 85 10 260 UNIT V mA V V mA °C °C °C mW °C Vishay Semiconductors Note (1) Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating condtions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (1) PARAMETER Supply current (pin 3) Supply voltage Transmission distance Output voltage low (pin 1) Minimum irradiance Maximum irradiance Directivity Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 400 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Angle of half transmission distance TEST CONDITION E v = 0, V S = 5 V Ev = 40 klx, sunlight SYMBOL ISD ISH VS d VOSL Ee min. Ee max. ϕ1/2 30 ± 45 0.3 2.7 40 100 0.45 MIN. 0.65 TYP. 0.85 0.95 5.5 MAX. 1.05 UNIT mA mA V m mV mW/m2 W/m2 deg Note (1) T amb = 25 °C, unless otherwise specified TYPICAL CHARACTERISTICS Tamb = 25 °C, unless otherwise specified 1 Ee Optical Test Signal tpo - Output Pulse Width (ms) (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 Output Pulse Width Input Burst Length t tpi * * tpi VO VOH VOL td1 ) T 10/f0 is recommended for optimal function 16110 Output Signal 1) 2) 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f 0 tpo2 ) t λ = 950 nm, Optical Test Signal, Fig.1 0.1 1 10 102 103 104 105 21391 Ee - Irradiance (mW/m²) Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Document Number: 81221 Rev. 1.4, 15-Oct-08 www.vishay.com 147 New TSOP582.., TSOP584.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems Ee min. - Threshold Irradiance (mW/m²) 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0.01 21393 Ee Optical Test Signal Correlation with Ambient Light Sources: 10 W/m² = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m² = 8.2 kLx (Daylight, T = 5900 K) 600 µs t = 60 ms Output Signal, (see fig. 4) 600 µs t 94 8134 VO VOH VOL Wavelength of Ambient Illumination: λ = 950 nm t on t off t 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m²) Fig. 6 - Sensitivity in Bright Ambient 1 Fig. 3 - Output Function 0.8 Ton, Toff - Output Pulse Width (ms) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0.1 1 10 10 2 Ton Ee min. - Threshold Irradiance (mW/m²) 0.9 0.8 0.7 f = f0 f = 30 kHz 0.6 0.5 f = 20 kHz 0.4 0.3 0.2 0.1 0 1 10 100 f = 10 kHz f = 100 Hz 1000 Toff λ = 950 nm, Optical Test Signal, Fig. 3 10 3 10 4 10 5 21392 Ee - Irradiance (mW/m²) Fig. 4 - Output Pulse Diagram 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.7 0.9 1.1 1.3 f = f0 ± 5 % Δ f(3 dB) = f0/10 21394 ΔVsRMS - AC Voltage on DC Supply Voltage (mV) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 500 E e min./Ee - Rel. Responsivity E - Max. Field Strength (V/m) 450 400 350 300 250 200 150 100 50 0 0 500 1000 1500 2000 2500 3000 16925 f/f0 - Relative Frequency 20747 f - EMI Frequency (MHz) Fig. 5 - Frequency Dependence of Responsivity Fig. 8 - Sensitivity vs. Electric Field Disturbances www.vishay.com 148 Document Number: 81221 Rev. 1.4, 15-Oct-08 New TSOP582.., TSOP584.. IR Receiver Modules for Remote Control Systems 0.8 0.7 Vishay Semiconductors 0° 10° 20° 30° Max. Envelope Duty Cycle 0.6 0.5 0.4 0.3 0.2 0.1 0 f = 38 kHz, Ee = 2 mW/m² 0 20 40 60 80 TSOP584.. TSOP582.. 40° 1.0 0.9 0.8 50° 60° 70° 0.7 80° 100 120 19258 0.6 0.4 0.2 0 0.2 0.4 0.6 21396 Burst Length (number of cycles/burst) Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length drel - Relative Transmission Distance Fig. 12 - Horizontal Directivity 0° 10° 20° 30° Ee min. - Threshold Irradiance (mW/m²) 0.45 0.4 0.35 1.0 0.3 0.25 0.2 0.15 - 30 0.9 0.8 40° 50° 60° 70° 0.7 80° - 10 10 30 50 70 90 19259 0.6 0.4 0.2 0 0.2 0.4 0.6 21397 Tamb - Ambient Temperature (°C) d rel - Relative Transmission Distance Fig. 10 - Sensitivity vs. Ambient Temperature 1.2 1.0 0.8 0.6 0.4 0.2 0 750 0.5 0.45 0.4 0.35 0.3 0.25 0.2 850 950 1050 1150 21398 Fig. 13 - Vertical Directivity S ( ) rel - Relative Spectral Sensitivity Ee min. - Sensitivity (mW/m²) 1.5 2 2.5 3 3.5 4 4.5 5 5.5 94 8408 - Wavelength (nm) VS - Supply Voltage (V) Fig. 11 - Relative Spectral Sensitivity vs. Wavelength Fig. 14 - Sensitivity vs. Supply Voltage Document Number: 81221 Rev. 1.4, 15-Oct-08 www.vishay.com 149 New TSOP582.., TSOP584.. Vishay Semiconductors SUITABLE DATA FORMAT The TSOP582.., TSOP584.. series are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP582.., TSOP584.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: • DC light (e.g. from tungsten bulb or sunlight) • Continuous signals at any frequency • Strongly or weakly modulated noise from fluorescent lamps with electronic ballasts (see figure 15 or figure 16) IR Receiver Modules for Remote Control Systems IR Signal IR Signal from Fluorescent Lamp with Low Modulation 0 16920 5 10 15 20 Time (ms) Fig. 15 - IR Signal from Fluorescent Lamp with Low Modulation IR Signal from Fluorescent Lamp with High Modulation IR Signal 0 16921 10 10 15 20 Time (ms) Fig. 16 - IR Signal from Fluorescent Lamp with High Modulation TSOP582.. Minimum burst length After each burst of length a minimum gap time is required of For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second Compatible to NEC code Compatible to RC5/RC6 code Compatible to Sony code Compatible to Thomson 56 kHz code Compatible to Mitsubishi code (38 kHz, preburst 8 ms, 16 bit) Compatible to Sharp code Suppression of interference from fluorescent lamps Note For data formats with short bursts please see the data sheet of TSOP581.. 10 cycles/burst 10 to 70 cycles ≥ 12 cycles 70 cycles > 4 x burst length 800 yes yes yes yes yes yes Most common disturbance signals are suppressed TSOP584.. 10 cycles/burst 10 to 35 cycles ≥ 12 cycles 35 cycles > 10 x burst length 1300 yes yes no yes yes yes Even extreme disturbance signals are suppressed www.vishay.com 150 Document Number: 81221 Rev. 1.4, 15-Oct-08 New TSOP582.., TSOP584.. IR Receiver Modules for Remote Control Systems PACKAGE DIMENSIONS in millimeters Vishay Semiconductors 19009 Document Number: 81221 Rev. 1.4, 15-Oct-08 www.vishay.com 151 New TSOP582.., TSOP584.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems OZONE DEPLETING SUBSTANCES POLICY STATEMENT It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively. 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA. 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany www.vishay.com 152 Document Number: 81221 Rev. 1.4, 15-Oct-08 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1