VEMI65AA-HCI

VEMI65AA-HCI Vishay Semiconductors 6-Channel EMI-Filter with ESD-Protection FEATURES • Ultra compact LLP2513-13L package 12 11 10 13 9 8 7 • Low package profile of 0.6 mm • 6-channel EMI-filter • Low leakage current 1 2 3 4 5 6 • Line resistance RS = 100  • Typical cut off frequency f3dB = 100 MHz • ESD-protection acc. IEC 61000-4-2 ± 30 kV contact discharge ± 30 kV air discharge • e4 - precious metal (e.g. Ag, Au, NiPd, NiPdAu) (no Sn) • Compliant to RoHS directive 2002/95/EC and in accordance to WEEE 2002/96/EC 20378 21839 MARKING (example only) YYXX 20720 Dot = pin 1 marking YY = type code (see table below) XX = date code ORDERING INFORMATION DEVICE NAME VEMI65AA-HCI ORDERING CODE VEMI65AA-HCI-GS08 TAPED UNITS PER REEL (8 mm TAPE ON 7" REEL) 3000 MINIMUM ORDER QUANTITY 15 000 PACKAGE DATA DEVICE NAME VEMI65AA-HCI PACKAGE NAME LLP2513-13L TYPE CODE 9P WEIGHT 5.5 mg MOLDING COMPOUND FLAMMABILITY RATING UL 94 V-0 MOISTURE SENSITIVITY LEVEL MSL level 1 (according J-STD-020) SOLDERING CONDITIONS 260 °C/10 s at terminals ABSOLUTE MAXIMUM RATINGS PARAMETER Peak pulse current ESD immunity Operating temperature Storage temperature TEST CONDITIONS All I/O pin to pin 13; acc. IEC 61000-4-5; tp = 8/20 μs; single shot Contact discharge acc. IEC61000-4-2; 10 pulses Air discharge acc. IEC61000-4-2; 10 pulses Junction temperature SYMBOL IPPM VESD TJ TSTG VALUE 4 ± 30 ± 30 - 40 to + 125 - 55 to + 150 UNIT A kV °C °C ** Please see document “Vishay Material Category Policy”: www.vishay.com/doc?99902 Document Number: 81384 Rev. 1.8, 18-May-10 For technical questions, contact: EMIFilter@vishay.com www.vishay.com 1 VEMI65AA-HCI Vishay Semiconductors APPLICATION NOTE With the VEMI65AA-HCI 6 different signal or data lines can be filtered and clamped to ground. Due to the different clamping levels in forward and reverse direction the clamping behaviour is Bidirectional and Asymmetric (BiAs). 6-Channel EMI-Filter with ESD-Protection L1IN L2IN L3IN L4IN L5IN L6IN 1 2 3 13 4 5 6 12 11 10 9 8 7 L1OUT L2OUT L3OUT L4OUT L5OUT L6OUT 20379 The 6 independent EMI-filter are placed between pin 1 and pin 12, pin 2 and pin 11, pin 3 and pin 10, pin 4 and pin 9, pin 5 and pin 8 and pin 6 and pin 7. They all are connected to a common ground pin 13 on the backside of the package. The circuit diagram of one EMI-filter-channel shows two identical Z-diodes at the input to ground and the output to ground. These Z-diodes are characterized by the breakthrough voltage level (VBR) and the diode capacitance (CD). Below the breakthrough voltage level the Z-diodes can be considered as capacitors. Together with these capacitors and the line resistance RS between input and output the device works as a low pass filter. Low frequency signals (f < f3dB) pass the filter while high frequency signals (f > f3dB) will be shorted to ground through the diode capacitances CD. RS In (pin 1, 2, 3, 4, 5, 6) CD Out (pin 7, 8, 9, 10, 11, 12) CD 20380 GND (pin 13) Each filter is symmetrical so that both ports can be used as input or output. www.vishay.com 2 For technical questions, contact: EMIFilter@vishay.com Document Number: 81384 Rev. 1.8, 18-May-10 VEMI65AA-HCI 6-Channel EMI-Filter with ESD-Protection ELECTRICAL CHARACTERISTICS VEMI65AA-HCI PARAMETER Protection paths Reverse stand off voltage Reverse current Reverse break down voltage TEST CONDITIONS/REMARKS Number of channels which can be protected at IR = 1 μA at VR = VRWM at IR = 1 mA at IPP = 1 A applied at the input, measured at the output; acc. IEC 61000-4-5 at IPP = IPPM = 4 A applied at the input, measured at the output; acc. IEC 61000-4-5 at IPP = - 1 A applied at the input, measured at the output; acc. IEC 61000-4-5 at IPP = IPPM = - 4 A applied at the input, measured at the output; acc. IEC 61000-4-5 at VR = 0 V; f = 1 MHz Input capacitance at VR = 2.5 V; f = 1 MHz ESD-clamping voltage Line resistance Cut-off frequency at ± 30 kV ESD-pulse acc. IEC 61000-4-2 Measured between input and output; IS = 10 mA VIN = 0 V; measured in a 50  system CIN VCESD RS f3dB 90 36 7.5 100 100 110 pF V  MHz SYMBOL Nchannel VRWM IR VBR VC-out VC-out VC-out VC-out CIN MIN. 5 6 -1 - 1.2 TYP. 60 MAX. 6 1 7 8 UNIT channel V μA V V V V V pF Vishay Semiconductors Pos. clamping voltage Neg. clamping voltage Note • Ratings at 25 °C, ambient temperature unless otherwise specified. All inputs (pin 1, 2, 3 and 4) to ground (pin 9) TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 120 % Rise time = 0.7 ns to 1 ns 100 % 80 % 80 % 60 % 53 % 8 µs to 100 % Discharge Current IESD 100 % IPPM 60 % 20 µs to 50 % 40 % 20 % 0% 0 10 20 30 40 40 % 27 % 20 % 0% - 10 0 10 20 30 40 50 60 70 80 90 100 20557 Time (ns) 20548 Time (µs) Fig. 1 - ESD Discharge Current Wave Form acc. IEC 61000-4-2 (330 /150 pF) Fig. 2 - 8/20 μs Peak Pulse Current Wave Form acc. IEC 61000-4-5 Document Number: 81384 Rev. 1.8, 18-May-10 For technical questions, contact: EMIFilter@vishay.com www.vishay.com 3 VEMI65AA-HCI Vishay Semiconductors 6-Channel EMI-Filter with ESD-Protection 100 10 70 f = 1 MHz 60 50 IF (mA) 1 0.1 0.01 0.001 CIN (pF) 0.5 0.6 0.7 0.8 0.9 1 40 30 20 10 0 0 1 2 3 4 5 6 20705 VF (V) 20706 VIN (V) Fig. 3 - Typical Forward Current IF vs. Forward Voltage VF Fig. 6 - Typical Input Capacitance CIN vs. Input Voltage VIN 8 0 6 5 Transmission (S21) (dB) 7 -5 - 10 - 15 - 20 - 25 - 30 - 35 - 40 1 VINPUT = 5 V VINPUT = 2 V VINPUT = 1 V VINPUT = 0 V Measured in a 50 Ω system VR (V) 4 3 2 1 0 0.01 0.1 1 10 100 1000 10 000 10 100 1000 10 000 20707 IR (µA) 20708 Frequency (MHz) Fig. 4 - Typical Reverse Voltage VR vs. Reverse Current IR Fig. 7 - Typical Small Signal Transmission (S21) at ZO = 50  14 12 10 Input clamping voltage VC (V) 8 6 4 2 0 0 Measured acc. IEC 61000-4-5 (8/20 µs - wave form) 1 2 3 4 VC 5 6 7 Output clamping voltage 20709 IPP (A) Fig. 5 - Typical Peak Clamping Voltage VC vs. Peak Pulse Current IPP www.vishay.com 4 For technical questions, contact: EMIFilter@vishay.com Document Number: 81384 Rev. 1.8, 18-May-10 VEMI65AA-HCI 6-Channel EMI-Filter with ESD-Protection PACKAGE DIMENSIONS in millimeters (inches): LLP2513-13L 1.85 (0.073) 1.75 (0.069) exp. DAP Vishay Semiconductors 0.4 (0.016) bsc 0.23 (0.009) 0.17 (0.007) 0.2 (0.008) x 45° 0.45 (0.018) 0.35 (0.014) Exp. DAP 2 (0.079) ref. 0.24 (0.009) 0.3 (0.012) 1.4 (0.055) 1.3 (0.051) 0.152 (0.006) ref. 0.6 (0.024) 0.05 (0.002) 2.55 (0.100) 2.45 (0.096) Pin 1 marking Foot print recommendation: 5 x 0. 4 = 2 (0.079) 0.4 (0.016) 0.2 (0.008) 0.15 (0.006) 0.4 (0.016) 0.5 (0.020) 0 (0.000) 0.4 (0.016) Solder resist mask 1.8 (0.071) Document no.:S8-V-3906.04-002 (4) Created - Date: 28. August 2006 Rev. 1 - Date: 27. May 2008 20381 0.42 (0.017) Solder pad Document Number: 81384 Rev. 1.8, 18-May-10 For technical questions, contact: EMIFilter@vishay.com www.vishay.com 5 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1