SPN100-12S

SPN100 100 WATT , Universal Input Fully Enclosed Switching Power Supply ELECTRICAL SPECIFICATIONS All specifications are typical at nominal input, full load. INPUT SPECIFICATIONS Input Voltage.............................................. AC 85-264V Input Frequency.......................................... 47 ~ 63 Hz Input Current.............................................. 0.66 ~ 1.3A Typ Inrush Current (100/230VAC cold start) .................15A ~ 25A Power Factor .............................................. .99 OUTPUT SPECIFICATIONS Output Voltage........................................... See Chart Output Adjustment.................................... ± 10% Efficiency.................................................... 79 ~ 87% Over-Voltage Protection.............................. 115 - 150% Manual Reset Over-Current Protection.............................. Automatic Recovery (105% min) Ripple and Noise........................................ 100 mVp-p max. Hold-Up Time............................................. 50 mS Line/Load Regulation.................................. See Chart Rise Time.................................................... 800 - 1600 mS Leakage Current (100/230VAC)........................ 0.75 mA FEATURES POWER FACTOR CORRECTED UNIVERSAL INPUT (AC85-264V) OVERVOLTAGE PROTECTION OVERCURRENT PROTECTION LIGHTWEIGHT CONSTRUCTION METAL CHASSIS WITH COVER COMPACT, LOW-PROFILE PACKAGES 3 YEAR WARRANTY GENERAL SPECIFICATIONS MTBF ......................................................... >140,000 Hours Isolation Voltage Primary to Secondary............... 3000VAC Primary to Case........................ 1500VAC. Secondary to Case.................... 500VAC. Isolation Resistance.................................... 100 M-Ohms min. ENVIRONMENTAL SPECIFICATIONS Operating Temperature .............................. 0˚C~+60˚C Derates Linearly 2.5%/˚C After 50˚C Cooling........................................................ Convection Temperature Coefficient.............................. 0.02% / ˚C Humidity.......................................................20-85% Rh (non-condensing) Storage Temperature.................................. -20˚C ~ +85˚C Shock Vibration.......................................... Shock: 20G (3 directions each 3 times) Vibration: 10 ~ 55Hz SAFETIES / EMI FCC-B EN 55022-B VCCI-II PHYSICAL SPECIFICATIONS Metal Enclosed - Terminal Block 72 Series MODEL SPN100-05S SPN100-12S SPN100-15S SPN100-24S SPN100-48S OUTPUT VOLTAGE 5 VDC 12 VDC 15 VDC 24 VDC 48 VDC CURRENT 85 ~ 264 VAC EFFICIENCY 100VAC 230VAC LINE REGULATION (MV) MAX LOAD REGULATION (mVmax) (0~100% Load) 20.0 A 8.6 A 7.0 A 4.4 A 2.2 A 79% 83% 83% 83% 84% 81% 85% 86% 86% 87% 10 mVmax 10 mVmax 10 mVmax 20 mVmax 20 mVmax 20 mVmax 20 mVmax 20 mVmax 40 mVmax 40 mVmax SPN100 LED 0.787 V. ADJ. I/O TERMINAL M4 (20max) 7.362 (187 ±1) +S +V -V 3.661 (93±1) 1.614 1.575 (40) 5.197 (132 ±0.5) (18) 1.535 (39 ±1) NOTE: *MOUNTING SCREWS NOT TO EXCEED MAX. PENETRATION OF 6mm. *REMOVE SHORT BAR BETWEEN (+S) AND (+V) , (-S) AND (-V) WHEN USE REMOTE SENSING. *TOLERANCE ±1mm. *ALL DIMENSIONS IN INCH (mm) 2-No. 8-32UNC (MOUNTING HOLES) 0.709 0.827 INCH 0.295 (7.5) 6.693 (170 ±0.5) SPN 100 NOTE: All specifications typical and nominal / full load and 25˚C unless otherwise noted. Mounting screw lenght should not exceed 0.31 inches or 8 mm. Avoid sustained operation in overload or dead short conditions. Specifications subject to changes without notice. • No. 8-32 mounting holes standard • Dimensions in mm • Terminal block or “pin” type connector available 73 (21) (41) -S 2-No. 8-32UNC (MOUNTING HOLES) BOTTOM L A/C IN N