PS2K4-15

PS2K4 Series With PFC 2400 Watt Single Output AC/DC Switching Power Supply FEATURES ● 3 Year Warranty ● Power Good Signal ● PF > 0.98 @ 230VAC ● Case Coating with Paint ● Remote ON/OFF Control ● With Parallel Function (N+1) ● Built-in Remote Sense Option ● Forced Air Cooling by Built-in DC Fan ● AC Input Voltage 180 ~ 260VAC, 3Ø3 Wire ● AC 220VAC, 1Ø or 380VAC, 3Ø4 Wire (Option) ● Input Voltage: 90~260VAC (90 ~ 170VAC Reduced Power) ● Short Circuit/ Overload/ Over Voltage/ Over Temperature Protection ● Can Adjust from 20% ~ 100% Output Voltage by External Control 1-5VDC SPECIFICATIONS: PS2K4 Series All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS 90 ~ 260VAC **(90 ~ 170 VAC reduced power - see “Output Power vs Input Voltage” derating curve)** Input Voltage Range 180 ~ 260VAC 3Ø3 Wire (other system available) Input Frequency 47 to 63Hz Input Current 13.5A / 230VAC Inrush Current 60A / 230VAC max. Leakage Current 3.5mA / 240VAC max. Remote ON/OFF Control Compatible with a TTL signal to turn ON/OFF OUTPUT SPECIFICATIONS Output Voltage See Table Output Power Range 2400 Watts max. ±5.0% typical adjustment by potentiometer Voltage Adjustment Range 20% ~ 100% adjustment by 1-5VDC external control. Voltage Tolerance (See Note 4) ±2.0% for PS2K4-09, ±1.0% for other models. Line Regulation ±0.5% Load Regulation ±1.5% for PS2K4-09, ±0.5% for other models. Output Current See Table Ripple & Noise (See Note 3) See Table Setup, Rise, Hold-Up Time 500ms, 50ms, 16ms at full load Temperature Coefficient ±0.04% / °C (0 ~ 50°C) Remote Sense Yes PROTECTION 110% ~ 135% Follow to output set up point. Over Voltage Protection Protection Type: Shutdown output voltage, re-power on to recover. 110% ~ 140% rated output power. Over Load Protection (See Note 5) Protection Type: Current limiting, delay shutdown output voltage, re-power on to recover. > 100°C / measure by heat sink, near transformer. Over Temperature Protection Protection Type: Shutdown output voltage, re-power to recover. GENERAL SPECIFICATIONS Efficiency See Table Withstand Voltage 3KVAC (input to output); 1.5KVAC (input to field ground) Isolation Resistance 100M ohms / 500VDC (input to output, input to field ground) Power Factor 0.98 / 230VAC Power Good Signal Open Collector of NPN Transistor DC Voltage Adjustment, Remote Sensing, Remote Control, Parallel Operation (refer to control terminal Special Function instruction manual). o Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PS2K4 Series With PFC 2400 Watt Single Output AC/DC Switching Power Supply SPECIFICATIONS (CONTINUED) ENVIRONMENTAL SPECIFICATIONS Working Temperature Storage Temperature Working Humidity Storage Humidity Vibration Cooling MTBF PHYSICAL SPECIFICATIONS Weight Dimensions Warranty SAFETY & EMC (See Note 6) Safety Standards EMI Conduction & Radiation Harmonic Current EMS Immunity -20°C to +65°C (refer to “Output Power vs Ambient Temperature” derating curve) -20°C to +85°C 20% to 90% RH (non-condensing) 10% to 95% RH 10 ~ 200Hz, 2g 10 min./1cycle, 60 min. each along X, Y, and Z axes. By fan: > 20% load or > 50°C 24,900 hours minimum MIL-HDBK-217F (25°C) 9.0kg 320(L) x 212(W) x 124(H) mm 3 years UL60950, TUVEN60950 Approved Compliance to EN55022 (CISPR22) class A Compliance to EN61000-3-2,3 Compliance to EN61000-4-2,3,4,5,6,8,11, Light industry level, criteria A. OUTPUT VOLTAGE / CURRENT RATING CHART Model Number PS2K4-09 PS2K4-12 PS2K4-15 PS2K4-24 PS2K4-48 Output Voltage 9 VDC 12 VDC 15 VDC 24 VDC 48 VDC Output Current 266A 200A 160A 100A 50A Output Power 2400W 2400W 2400W 2400W 2400W Ripple & Noise 90mVp-p 120mVp-p 150mVp-p 150mVp-p 200mVp-p Efficiency 83% 84% 85% 88% 89% NOTES 1. Input voltage is 90 ~ 260VAC however, the unit does not reach full power until >170VAC. See derating curve below. 2. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 3. Ripple & noise is measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 4. Tolerance: includes set up tolerance, line regulation and load regulation. 5. Current limiting 3 times (1.5s, 3.0s, 5.0s) then intelligent auto recovery before shut down 6. The power supply is considered a component, which will be installed into final equipment. The final equipment must be re-confirmed that it still meets EMC directives. DERATING CURVES Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PS2K4 Series With PFC 2400 Watt Single Output AC/DC Switching Power Supply CONNECTOR PIN-OUT DRAWINGS Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PS2K4 Series With PFC 2400 Watt Single Output AC/DC Switching Power Supply MECHANICAL DRAWING Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797