W3EG6466S265AD4

White Electronic Designs W3EG6466S-AD4 -BD4 PRELIMINARY* 512MB – 2x32Mx64 DDR SDRAM UNBUFFERED, w/PLL FEATURES DDR200, DDR266 and DDR333 • JEDEC design specifications Double-data-rate architecture Bi-directional data strobes (DQS) Differential clock inputs (CK & CK#) Programmable Read Latency 2,2.5 (clock) Programmable Burst Length (2,4,8) Programmable Burst type (sequential & interleave) Edge aligned data output, center aligned data input Auto and self refresh Serial presence detect Dual Rank Power supply: 2.5V ± 0.20V JEDEC standard 200 pin SO-DIMM package • Package height options: AD4: 35.5mm (1.38") BD4: 31.75mm (1.25") NOTE: Consult factory for availability of: • RoHS compliant products • Vendor source control options • Industrial temperature option * This product is under development, is not qualified or characterized and is subject to change without notice. DESCRIPTION The W3EG6466S is a 2x32Mx64 Double Data Rate SDRAM memory module based on 512Mb DDR SDRAM components. The module consists of sixteen 32Mx8 components as eight 64Mx8 stacked DDR SDRAMs in 66 pin TSOP packages mounted on a 200 pin FR4 substrate. Synchronous design allows precise cycle control with the use of system clock. Data I/O transactions are possible on both edges and Burst Lengths allow the same device to be useful for a variety of high bandwidth, high performance memory system applications. OPERATING FREQUENCIES DDR333 @CL=2.5 Clock Speed CL-tRCD-tRP 166MHz 2.5-3-3 DDR266 @CL=2 133MHz 2-2-2 DDR266 @CL=2.5 133MHz 2.5-3-3 DDR200 @CL=2 100MHz 2-2-2 White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 1 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs PIN CONFIGURATION Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Symbol VREF VREF VSS VSS DQ0 DQ4 DQ1 DQ5 VCC VCC DQS0 DQM0 DQ2 DQ6 VSS VSS DQ3 DQ7 DQ8 DQ12 VCC VCC DQ9 DQ13 DQS1 DQM1 VSS VSS DQ10 DQ14 DQ11 DQ15 VCC VCC CK0 VCC CK0# VSS VSS VSS DQ16 DQ20 DQ17 DQ21 VCC VCC DQS2 DQM2 DQ18 DQ22 Pin 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Symbol VSS VSS DQ19 DQ23 DQ24 DQ28 VCC VCC DQ25 DQ29 DQS3 DQM3 VSS VSS DQ26 DQ30 DQ27 DQ31 VCC VCC NC NC NC NC VSS VSS DQS8 DQM8 NC NC VCC VCC NC NC NC NC VSS VSS NC VSS NC VCC VCC VCC CKE1 CKE0 NC NC A12 A11 Pin 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 Symbol A9 A8 VSS VSS A7 A6 A5 A4 A3 A2 A1 A0 VCC VCC A10/AP BA1 BA0 RAS# WE# CAS# CS0# CS1# NC NC VSS VSS DQ32 DQ36 DQ33 DQ37 VCC VCC DQS4 DQM4 DQ34 DQ38 VSS VSS DQ35 DQ39 DQ40 DQ44 VCC VCC DQ41 DQ45 DQS5 DQM5 VSS VSS Pin 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 Symbol DQ42 DQ46 DQ43 DQ47 VCC VCC VCC NC VSS NC VSS VSS DQ48 DQ52 DQ49 DQ53 VCC VCC DQS6 DQM6 DQ50 DQ54 VSS VSS DQ51 DQ55 DQ56 DQ60 VCC VCC DQ57 DQ61 DQS7 DQM7 VSS VSS DQ58 DQ62 DQ59 DQ63 VCC VCC SDA SA0 SCL SA1 VCCSPD SA2 VCCID NC W3EG6466S-AD4 -BD4 PRELIMINARY PIN NAMES A0 – A12 BA0-BA1 DQ0-DQ63 DQS0-DQS7 CK0 CK0# CKE0-CKE1 CS0#-CS1# RAS# CAS# WE# DQM0-DQM7 VCC VSS VREF VCCSPD SDA SCL SA0-SA2 VCCID NC * Not Used ACCress input (Multiplexed) Bank Select ACCress Data Input/Output Data Strobe Input/Output Clock Input Clock input Clock Enable input Chip select Input Row ACCress Strobe Column ACCress Strobe Write Enable Data-In Mask Power Supply Ground Power Supply for Reference Serial EEPROM Power Supply Serial data I/O Serial clock ACCress in EEPROM VCC Identification Flag No Connect White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 2 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs FUNCTIONAL BLOCK DIAGRAM CS1# CS0# DQS0 DQM0 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQS1 DQM1 DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# DQS DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DQS6 DQM6 DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# DQS DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQS5 DQM5 DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# W3EG6466S-AD4 -BD4 PRELIMINARY CS# DQS4 DQM4 DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# DQS CS# CS# CS# DQS DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQS2 DQM2 CS# DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# DQS CS# DQS DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQS3 DQM3 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQS7 DQM7 CS# DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# DQS CS# DM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 CS# DQS DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQ56 DQ57 DQ58 DQ60 DQ61 DQ62 DQ63 DQ64 RAS# CAS# BA0-BA1 WE# A0-A12 CKE0 CKE1 RAS: DDR SDRAMs CAS: DDR SDRAMs BA0-BA1: DDR SDRAMs WE: DDR SDRAMs A0-A12: DDR SDRAMs CKE0: DDR SDRAMs CKE1: DDR SDRAMs SCL CK0# CK0 VCC 120Ω CK0A CLK0/CLK0# CLK1/CLK1# PLL CK0A# CLK2/CLK2# CLK3/CLK3# FEEDBACK SERIAL PD SDA A0 SA0 A1 SA1 A2 SA2 VCC DDR SDRAM DDR SDRAM NOTE: All datalines are terminated through a 22 ohm series resistor. GND White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 3 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to VSS Voltage on VCC supply relative to VSS Storage Temperature Power Dissipation Short Circuit Current Note: Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. W3EG6466S-AD4 -BD4 PRELIMINARY Symbol VIN, VOUT VCC, VCCQ TSTG PD IOS Value -0.5 to 3.6 -1.0 to 3.6 -55 to +150 16 50 Units V V °C W mA DC CHARACTERISTICS 0°C ≤ TA ≤ 70°C, VCC = 2.5V ± 0.2V Symbol VCC VCCQ VREF VTT VIH VIL VOH VOL Parameter Supply Voltage Supply Voltage Reference Voltage Termination Voltage Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage Min 2.3 2.3 VCCQ/2 - 50mV VREF - 0.04 VREF + 0.15 -0.3 VTT + 0.76 — Max 2.7 2.7 VCCQ/2 + 50mV VREF + 0.04 VCCQ + 0.3 VREF - 0.15 — VTT - 0.76 Unit V V V V V V V V CAPACITANCE TA = 25°C, f = 1MHz, VCC = 3.3V, VREF =1.4V ± 200mV Parameter Input Capacitance (A0-A12) Input Capacitance (RAS#, CAS#, WE#) Input Capacitance (CKE0, CKE1) Input Capacitance (CK0,CK0#) Input Capacitance (CS0#, CS1#) Input Capacitance (DQM0-DQM8) Input Capacitance (BA0-BA1) Data input/output capacitance (DQ0-DQ63)(DQS) Symbol CIN1 CIN2 CIN3 CIN4 CIN5 CIN6 CIN7 COUT Max 50 50 26 5.5 26 13 50 13 Unit pF pF pF pF pF pF pF pF White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 4 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs IDD SPECIFICATIONS AND TEST CONDITIONS 0°C ≤ TA ≤ 70°C, VCCQ = 2.5V ±0.2V, VCC = 2.5V ±0.2V W3EG6466S-AD4 -BD4 PRELIMINARY DDR333@CL=2.5 DDR266@CL=2, 2.5 Parameter Symbol Conditions One device bank; Active - Precharge; tRC=tRC(MIN); tCK=tCK(MIN); DQ,DM and DQS inputs changing once per clock cycle; Address and control inputs changing once every two cycles. One device bank; Active-Read-Precharge; Burst = 2; tRC=tRC(MIN);tCK=tCK(MIN); Iout = 0mA; Address and control inputs changing once per clock cycle. All device banks idle; Power- down mode; tCK=tCK(MIN); CKE=(low) CS# = High; All device banks idle; tCK=tCK(MIN); CKE = high; Address and other control inputs changing once per clock cycle. Vin = Vref for DQ, DQS and DM. One device bank active; Power-down mode; tCK(MIN); CKE=(low) CS# = High; CKE = High; One device bank; Active-Precharge; tRC=tRAS(MAX); tCK=tCK(MIN); DQ, DM and DQS inputs changing twice per clock cycle; Address and other control inputs changing once per clock cycle. Burst = 2; Reads; Continous burst; One device bank active;Address and control inputs changing once per clock cycle; tCK=tCK(MIN); Iout = 0mA. Burst = 2; Writes; Continous burst; One device bank active; Address and control inputs changing once per clock cycle; tCK=tCK(MIN); DQ,DM and DQS inputs changing twice per clock cycle. tRC=tRC(MIN) CKE ≤ 0.2V Four bank interleaving Reads (BL=4) with auto precharge with tRC=tRC (MIN); tCK=tCK(MIN); Address and control inputs change only during Active Read or Write commands. Max 1600 Max 1440 DDR200@CL=2 Max 1360 Units mA Operating Current IDD0 1800 1640 1560 mA Operating Current IDD1 Precharge Power-Down Standby Current IDD2P 48 400 48 320 48 320 mA mA Idle Standby Current IDD2F Active Power-Down Standby Current IDD3P 560 880 480 720 480 720 mA mA Active Standby Current IDD3N 2160 1840 1840 mA Operating Current IDD4R 2160 1800 1800 mA Operating Current IDD4W Auto Refresh Current Self Refresh Current IDD5 IDD6 2240 48 3120 2000 48 2960 2000 48 2720 mA mA mA Operating Current IDD7A * For DDR333 consult factory White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 5 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs DETAILED TEST CONDITIONS FOR DDR SDRAM IDD1 & IDD7A IDD1 : OPERATING CURRENT : ONE BANK 1. 2. 3. Typical Case : VCC=2.5V, T=25°C Worst Case : VCC=2.7V, T=10°C Only one bank is accessed with tRC (min), Burst Mode, Address and Control inputs on NOP edge are changing once per clock cycle. IOUT = 0mA Timing Patterns : • DDR200 (100 MHz, CL=2) : tCK=10ns, CL2, BL=4, tRCD=2*tCK, tRAS=5*tCK Read : A0 N R0 N N P0 N A0 N - repeat the same timing with random address changing; 50% of data changing at every burst DDR266 (133MHz, CL=2.5) : tCK=7.5ns, CL=2.5, BL=4, tRCD=3*tCK, tRC=9*tCK, tRAS=5*tCK Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing; 50% of data changing at every burst DDR266 (133MHz, CL=2) : tCK=7.5ns, CL=2, BL=4, tRCD=3*tCK, tRC=9*tCK, tRAS=5*tCK Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing; 50% of data changing at every burst DDR333 (166MHz, CL=2.5) : tCK=6ns, BL=4, tRCD=10*tCK, tRAS=7*tCK Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing; 50% of data changing at every burst • W3EG6466S-AD4 -BD4 PRELIMINARY IDD7A : OPERATING CURRENT : FOUR BANKS 1. 2. 3. Typical Case : VCC=2.5V, T=25°C Worst Case : VCC=2.7V, T=10°C Four banks are being interleaved with tRC (min), Burst Mode, Address and Control inputs on NOP edge are not changing. Iout=0mA Timing Patterns : • DDR200 (100 MHz, CL=2) : tCK=10ns, CL2, BL=4, tRRD=2*tCK, tRCD=3*tCK, Read with Autoprecharge Read : A0 N A1 R0 A2 R1 A3 R2 A0 R3 A1 R0 - repeat the same timing with random address changing; 100% of data changing at every burst DDR266 (133MHz, CL=2.5) : tCK=7.5ns, CL=2.5, BL=4, tRRD=3*tCK, tRCD=3*tCK Read with Autoprecharge Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing; 100% of data changing at every burst DDR266 (133MHz, CL=2) : tCK=7.5ns, CL2=2, BL=4, tRRD=2*tCK, tRCD=2*tCK Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing; 100% of data changing at every burst DDR333 (166MHz, CL=2.5) : tCK=6ns, BL=4, tRRD=3*tCK, tRCD=3*tCK, Read with Autoprecharge Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing; 100% of data changing at every burst 4. 4. • • • • • Legend : A = Activate, R = Read, W = Write, P = Precharge, N = NOP A (0-3) = Activate Bank 0-3 R (0-3) = Read Bank 0-3 White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 6 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3EG6466S-AD4 -BD4 PRELIMINARY DDR SDRAM COMPONENT ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS AC CHARACTERISTICS PARAMETER Access window of DQs from CK/CK# CK high-level width CK low-level width Clock cycle time CL = 2.5 CL = 2 DQ and DM input hold time relative to DQS DQ and DM input setup time relative to DQS DQ and DM input pulse width (for each input) Access window of DQS from CK/CK# DQS input high pulse width DQS input low pulse width DQS-DQ skew, DQS to last DQ valid, per group, per access Write command to first DQS latching transition DQS falling edge to CK rising - setup time DQS falling edge from CK rising - hold time Half clock period Data-out high-impedance window from CK/CK# Data-out low-impedance window from CK/CK# Address and control input hold time (fast slew rate) Address and control input setup time (fast slew rate) Address and control input hold time (slow slew rate) Address and control input setup time (slow slew rate) Address and Control input pulse width (for each input) LOAD MODE REGISTER command cycle time SYMBOL tAC tCH tCL tCK (2.5) tCK (2) tDH tDS tDIPW tDQSCK tDQSH tDQSL tDQSQ tDQSS tDSS tDSH tHP tHZ tLZ tIHF tISF tIHS tISS tIPW tMRD -0.70 0.75 0.75 0.8 0.8 2.2 12 0.75 0.20 0.20 tCH,tCL +0.70 -0.75 0.90 0.90 1 1 2.2 15 MIN -0.70 0.45 0.45 6 7.5 0.45 0.45 1.75 -0.60 0.35 0.35 0.4 1.25 0.75 0.20 0.20 tCH,tCL +0.75 -0.75 0.90 .900 1 1 2.2 15 +0.60 335 MAX +0.70 0.55 0.55 13 13 MIN -0.75 0.45 0.45 7.5 7.5 0.5 0.5 1.75 -0.75 0.35 0.35 0.5 1.25 0.75 0.20 0.20 tCH,tCL +0.75 +0.75 262 MAX +0.75 0.55 0.55 13 13 265/202 MIN -0.75 0.45 0.45 7.5 7.5/10 0.5 0.5 1.75 -0.75 0.35 0.35 0.5 1.25 +0.75 MAX +0.75 0.55 0.55 13 13 ns tCK tCK ns ns ns ns ns ns tCK tCK ns tCK tCK tCK ns ns ns ns ns ns ns ns ns 8 16, 36 16, 36 12 12 12 12 22, 23 26 26 39, 44 39, 44 23, 27 23, 27 27 UNITS NOTES White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 7 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3EG6466S-AD4 -BD4 PRELIMINARY DDR SDRAM COMPONENT ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS (Continued) AC CHARACTERISTICS PARAMETER DQ-DQS hold, DQS to first DQ to go non-valid, per access Data hold skew factor ACTIVE to PRECHARGE command ACTIVE to READ with Auto precharge command ACTIVE to ACTIVE/AUTO REFRESH command period AUTO REFRESH command period ACTIVE to READ or WRITE delay PRECHARGE command period DQS read preamble DQS read postamble ACTIVE bank a to ACTIVE bank b command DQS write preamble DQS write preamble setup time DQS write postamble Write recovery time Internal WRITE to READ command delay Data valid output window REFRESH to REFRESH command interval Average periodic refresh interval Terminating voltage delay to VDD Exit SELF REFRESH to non-READ command Exit SELF REFRESH to READ command SYMBOL tQH tQHS tRAS tRAP tRC tRFC tRCD tRP tRPRE tRPST tRRD tWPRE tWPRES tWPST tWR tWTR NA tREFC tREFI tVTD tXSNR tXSRD 0 75 200 42 15 60 72 15 15 0.9 0.4 12 0.25 0 0.4 15 1 tQH -tDQSQ 70.3 7.8 0 75 200 0.6 1.1 0.6 MIN tHP - tQHS 0.75 70,000 40 15 60 75 15 15 0.9 0.4 15 0.25 0 0.4 15 1 tQH -tDQSQ 70.3 7.8 0 75 200 0.6 1.1 0.6 335 MAX MIN tHP - tQHS 0.75 120,000 40 20 65 75 20 20 0.9 0.4 15 0.25 0 0.4 15 1 tQH -tDQSQ 70.3 7.8 0.6 1.1 0.6 262 MAX 265/202 MIN tHP - tQHS 0.75 120,000 MAX ns ns ns ns ns ns ns ns tCK tCK ns tCK ns tCK ns tCK ns µs µs ns ns tCK 22 21 21 18, 19 17 37 37 42 31, 47 22, 23 UNITS NOTES White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 8 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs Notes 1. All voltages referenced to VSS. 2. Tests for AC timing, IDD, and electrical AC and DC characteristics may be conducted at nominal reference/supply voltage levels, but the related specifications and device operation are guaranteed for the full voltage range specified. 3. Outputs measured with equivalent load: W3EG6466S-AD4 -BD4 PRELIMINARY VTT 50Ω Reference Reference Point Point 30pF Output (VOUT) 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. AC timing and IDD tests may use a VIL-to-VIH swing of up to 1.5V in the test environment, but input timing is still referenced to VREF (or to the crossing point for CK/CK#), and parameter specifications are guaranteed for the specified AC input levels under normal use conditions. The mini-mum slew rate for the input signals used to test the device is 1V/ns in the range between VIL(AC) and VIH(AC). The AC and DC input level specifications are as defined in the SSTL_2 Standard (i.e., the receiver will effectively switch as a result of the signal crossing the AC input level, and will remain in that state as long as the signal does not ring back above [below] the DC input LOW [HIGH] level). VREF is expected to equal VCCQ/2 of the transmitting device and to track variations in the DC level of the same. Peak-to-peak noise (non-common mode) on VREF may not exceed ±2 percent of the DC value. Thus, from VCCQ/2, VREF is allowed ±25mV for DC error and an additional ±25mV for AC noise. This measurement is to be taken at the nearest VREF bypass capacitor. VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF and must track variations in the DC level of VREF. IDD is dependent on output loading and cycle rates. Specified values are obtained with mini-mum cycle time at CL = 2 for 262, 263, and 202, CL = 2.5 for 335 and 265 with the outputs open. Enables on-chip refresh and address counters. IDD specifications are tested after the device is properly initialized, and is averaged at the defined cycle rate. This parameter is sampled. VCC = +2.5V ±0.2V, VCCQ = +2.5V ±0.2V, VREF = VSS, f = 100 MHz, = 25°C, VOUT(DC) = VCCQ/2, VOUT (peak to peak) TA = 0.2V. DM input is grouped with I/O pins, reflecting the fact that they are matched in loading. For slew rates less than 1 V/ns and greater than or equal to 0.5 V/ns. If slew rate is less than 0.5 V/ns, timing must be derated: tIS has an additional 50ps per each 100mV/ns reduction in slew rate from 500mV/ns, while tIH is unaffected. If slew rate exceeds 4.5 V/ns, functionality is uncertain. For 335, slew rates must be ≥ 0.5 V/ns. The CK/CK# input reference level (for timing referenced to CK/CK#) is the point at which CK and CK# cross; the input reference level for signals other than CK/CK# is VREF. Inputs are not recognized as valid until VREF stabilizes. Exception: during the period before VREF stabilizes, CKE < 0.3 x VCCQ is recognized as LOW. The output timing reference level, as measured at the timing reference point indicated in Note 3, is VTT. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referenced to a specific voltage level, but specify when the device output is no longer driving (HZ) or begins driving (LZ). 17. The intent of the Don’t Care state after completion of the postamble is the DQSdriven signal should either be high, low, or high-Z and that any signal transition within the input switching region must follow valid input requirements. That is, if DQS transitions high (above VIH DC (MIN) then it must not transition low (below VIH DC) prior to tDQSH (MIN). 18. This is not a device limit. The device will operate with a negative value, but system performance could be degraded due to bus turnaround. 19. It is recommended that DQS be valid (HIGH or LOW) on or before the WRITE command. The case shown (DQS going from High-Z to logic LOW) applies when no WRITEs were previously in progress on the bus. If a previous WRITE was in progress, DQS could be HIGH during this time, depending on tDQSS. 20. MIN (tRC or tRFC) for IDD measurements is the smallest multiple of tCK that meets the minimum absolute Value for the respective parameter. tRAS (MAX) for IDD measurements is the largest multiple of tCK that meets the maximum absolute value for tRAS. 21. The refresh period 64ms. This equates to an aver-age refresh rate of 7.8125µs. However, an AUTO REFRESH command must be asserted at least once every 70.3µs; burst refreshing or posting by the DRAM controller greater than eight refresh cycles is not allowed. 22. The valid data window is derived by achieving other specifications: tHP (tCK/2), tDQSQ, and tQH (tQH = tHP - tQHS). The data valid window derates directly porportional with the clock duty cycle and a practical data valid window can be derived. The clock is allowed a maximum duty cycle variation of 45/55, beyond which functionality is uncertain. Figure 8, Derating Data Valid Window, shows derating curves for duty cycles ranging between 50/50 and 45/55. 23. Each byte lane has a corresponding DQS. 24. This limit is actually a nominal value and does not result in a fail value. CKE is HIGH during REFRESH command period (tRFC [MIN]) else CKE is LOW (i.e., during standby). 25. To maintain a valid level, the transitioning edge of the input must: a. Sustain a constant slew rate from the current AC level through to the target AC level, VIL(AC) or VIH(AC). b. Reach at least the target AC level.After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC). 26. JEDEC specifies CK and CK# input slew rate must be ≥ 1V/ns (2V/ns differentially). 27. DQ and DM input slew rates must not deviate from DQS by more than 10 percent. If the DQ/ DM/DQS slew rate is less than 0.5V/ns, timing must be derated: 50ps must be added to tDS and tDH for each 100mv/ns reduction in slew rate. If slew rate exceeds 4V/ns, functionality is uncertain. For 335, slew rates must be ≥ 0.5 V/ns. 28. VCC must not vary more than 4 percent if CKE is not active while any bank is active. 29. The clock is allowed up to ±150ps of jitter. Each timing parameter is allowed to vary by the same amount. 30. tHP min is the lesser of tCL minimum and tCH minimum actually applied to the device CK and CK# inputs, collectively during bank active. 31. READs and WRITEs with auto precharge are not allowed to be issued until tRAS(MIN) can be satisfied prior to the internal precharge command being issued. 32. Any positive glitch must be less than 1/3 of the clock and not more than +400mV or 2.9V, whichever is less. Any negative glitch must be less than 1/3 of the clock cycle and not exceed either -300mV or 2.2V, whichever is more positive. White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 9 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs 33. The voltage levels used are derived from a mini-mum VCC level and the referenced test load. In practice, the voltage levels obtained from a properly terminated bus will provide significantly different voltage values. 34. VIH overshoot: VIH (MAX) = VCCQ + 1.5V for a pulse width ≤ 3ns and the pulse width can not be greater than 1/3 of the cycle rate. VIL undershoot: VIL (MIN) = -1.5V for a pulse width ≤ 3ns and the pulse width can not be greater than 1/3 of the cycle rate. 35. VCC and VCCQ must track each other. 36. tHZ (MAX) will prevail over tDQSCK (MAX) + tRPST (MAX) condition. tLZ (MIN) will prevail over tDQSCK (MIN) + tRPRE (MAX) condition. 37. tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). 38. During Initialization, VCCQ, VTT, and VREF must be equal to or less than VCC + 0.3V. Alternatively, VTT may be 1.35V maximum during power up, even if VCC/VCCQ are 0.0V, provided a minimum of 42 0 of series resistance is used between the VTT supply and the input pin. 39. The current part operates below the slowest JEDEC operating frequency of 83 MHz. As such, future die may not reflect this option. W3EG6466S-AD4 -BD4 PRELIMINARY 40. Random addressing changing and 50 percent of data changing at every transfer. 41. Random addressing changing and 100 percent of data changing at every transfer. 42. CKE must be active (high) during the entire time a refresh command is executed. That is, from the time the AUTO REFRESH command is registered, CKE must be active at each rising clock edge, until tREF later. 43. IDD2N specifies the DQ, DQS, and DM to be driven to a valid high or low logic level. IDD2Q is similar to IDD2F except IDD2Q specifies the address and control inputs to remain stable. Although IDD2F, IDD2N, and IDD2Q are similar, IDD2F is “worst case.” 44. Whenever the operating frequency is altered, not including jitter, the DLL is required to be reset. This is followed by 200 clock cycles. 45. Leakage number reflects the worst case leakage possible through the module pin, not what each memory device contributes. 46. When an input signal is HIGH or LOW, it is defined as a steady state logic HIGH or LOW. 47. The 335 speed grade will operate with tRAS (MIN) = 40ns and tRAS (MAX) = 120,000ns at any slower frequency. White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 10 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs ORDERING INFORMATION FOR AD4 Part Number W3EG6466S335AD4 W3EG6466S262AD4 W3EG6466S265AD4 W3EG6466S202AD4 Speed 166MHz/333Mbps, CL=2.5 133MHz/266Mbps, CL=2 133MHz/266Mbps, CL=2.5 100MHz/200Mbps, CL=2 W3EG6466S-AD4 -BD4 PRELIMINARY Height* 35.5 (1.38) 35.5 (1.38) 35.5 (1.38) 35.5 (1.38) NOTES: • Consult Factory for availability of RoHS compliant products. (G = RoHS Compliant) • Vendor specific part numbers are used to provide memory components source control. The place holder for this is shown as lower case “x” in the part numbers above and is to be replaced with the respective vendors code. Consult factory for qualified sourcing options. (M = Micron, S = Samsung & consult factory for others) • Consult factory for availability of industrial temperature (-40°C to 85°C) option PACKAGE DIMENSIONS FOR AD4 67.56 (2.666) MAX. 2.0 (0.079) 6.35 (0 .250) MAX. 3.98 ± 0.1 (0.157 ± 0.004) 35.05 (1.38) MAX. 20 (0.787) P1 2.31 (0.091) REF. 4.19 (0.165) 1.80 (0.071) 11.40 (0.449) 47.40 (1.866) 3.98 (0.157) MIN. 1.0 ± 0.1 (0.039 ± 0.004) * ALL DIMENSIONS ARE IN MILIMETERS AND (INCHES) White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 11 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs ORDERING INFORMATION FOR BD4 Part Number W3EG6466S335BD4 W3EG6466S262BD4 W3EG6466S265BD4 W3EG6466S202BD4 Speed 166MHz/333Mbps, CL=2.5 133MHz/266Mbps, CL=2 133MHz/266Mbps, CL=2.5 100MHz/200Mbps, CL=2 W3EG6466S-AD4 -BD4 PRELIMINARY Height* 31.75 (1.25) 31.75 (1.25) 31.75 (1.25) 31.75 (1.25) NOTES: • Consult Factory for availability of RoHS compliant products. (G = RoHS Compliant) • Vendor specific part numbers are used to provide memory components source control. The place holder for this is shown as lower case “x” in the part numbers above and is to be replaced with the respective vendors code. Consult factory for qualified sourcing options. (M = Micron, S = Samsung & consult factory for others) • Consult factory for availability of industrial temperature (-40°C to 85°C) option PACKAGE DIMENSIONS FOR BD4 67.56 (2.666) MAX 3.98 ± 0.1 (0.157 ± 0.004) 6.35 (0.250) MAX. 31.75 (1.25) 20 (0.787) 2.31 (0.091) REF. 4.19 (0.165) 1.80 (0.071) 11.40 (0.449) 47.40 (1.866) 3.98 (0.157) MIN. 1.0 ± 0.1 (0.039 ± 0.004) * ALL DIMENSIONS ARE IN MILIMETERS AND (INCHES) White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 12 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs Document Title 512MB – 64Mx64 DDR SDRAM UNBUFFERED, w/PLL W3EG6466S-AD4 -BD4 PRELIMINARY Revision History Rev # Rev A Rev 0 History Created 0.1 Upated IDD specs. 0.2 Added AD4 and BD4 package options 0.3 Added document title page 0.4 Removed "ED" from part number 0.5 Moved from advanced to preliminary Release Date 7-21-02 8-04 Status Advanced Preliminary Rev 1 1.0 Upated IDD and CAP specs. 1.1 Added AC specs 11-04 Preliminary Rev 2 2.1 Added lead-free and RoHS notes 2.2 Added source control notes 2.3 Added industrial temperature options 1-05 Preliminary White Electronic Designs Corp. reserves the right to change products or specifications without notice. January 2005 Rev. 2 13 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com