WMF128K8-70CQ5

White Electronic Designs WMF128K8-XXX5 128Kx8 MONOLITHIC FLASH, SMD 5962-96690 FEATURES Access Times of 50*, 60, 70, 90, 120, 150ns Packaging • 32 lead, Hermetic Ceramic, 0.400" SOJ (Package 101) • 32 pin, Hermetic Ceramic, 0.600" DIP (Package 300) • 32 lead, Flatpack (Package 220) • 32 lead, Formed Flatpack (Package 221) • 32 pin, Rectangular Ceramic Leadless Chip Carrier (Package 601) 100,000 Erase/Program Cycles Minimum Sector Erase Architecture • 8 equal size sectors of 16KBytes each • Any combination of sectors can be concurrently erased. Also supports full chip erase Organized as 128Kx8 Commercial, Industrial and Military Temperature Ranges 5 Volt Programming. 5V ± 10% Supply. Low Power CMOS Embedded Erase and Program Algorithms TTL Compatible Inputs and CMOS Outputs Page Program Operation and Internal Program Control Time. This product is subject to change without notice. Note: For programming information refer to Flash Programming 1M5 Application Note. * The access time of 50ns is available in Industrial and Commercial temperature ranges only. Pin Configuration For WMF128K8-XXX5 32 DIP 32 CSOJ 32 Flatpack Pin Configuration For WMF128K8-XCLX5 32 CLCC Top View A12 NC A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS Top View WE# A15 A16 VCC NC VCC WE# NC A14 A13 A8 A9 A11 OE# A10 CS# I/O7 I/O6 I/O5 I/O4 I/O3 I/O1 I/O2 I/O3 I/O4 I/O5 Pin Description A0-16 I/O0-7 CS# OE# WE# VCC VSS Address Inputs Data Input/Output Chip Select Output Enable Write Enable +5.0V Power Ground White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 1 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com I/O6 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 4 3 2 1 32 31 30 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 5 29 6 28 7 27 8 26 25 9 10 24 11 23 12 22 13 21 14 15 16 17 18 19 20 A14 A13 A8 A9 A11 OE# A10 CS# I/O7 NC White Electronic Designs ABSOLUTE MAXIMUM RATINGS (1) Parameter Operating Temperature Supply Voltage (VCC) Signal Voltage Range (any pin except A9) (2) Storage Temperature Range Lead Temperature (soldering, 10 seconds) Data Retention Mil Temp Endurance (write/erase cycles) (Mil Temp) A9 Voltage for sector protect (VID) (3) -55 to +125 -2.0 to +7.0 -2.0 to +7.0 -65 to +150 +300 10 10,000 min -2.0 to +14.0 Unit °C V V °C °C years cycles V Parameter Supply Voltage Input High Voltage Input Low Voltage Operating Temp. (Mil.) Operating Temp. (Ind.) A9 Voltage for Sector Protect WMF128K8-XXX5 RECOMMENDED OPERATING CONDITIONS Symbol VCC VIH VIL TA TA VID Min 4.5 2.0 -0.5 -55 -40 11.5 Max 5.5 VCC + 0.5 +0.8 +125 +85 12.5 Unit V V V °C °C V NOTES: 1. Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs may overshoot VSS to -2.0 V for periods of up to 20ns. Maximum DC voltage on output and I/O pins is VCC + 0.5V. During voltage transitions, outputs may overshoot to Vcc + 2.0 V for periods of up to 20ns. 3. Minimum DC input voltage on A9 pin is -0.5V. During voltage transitions, A9 may overshoot Vss to -2V for periods of up to 20ns. Maximum DC input voltage on A9 is +13.5V which may overshoot to 14.0 V for periods up to 20ns. CAPACITANCE TA = +25°C Parameter Address Input capacitance Output Enable capacitance Write Enable capacitance Chip Select capacitance Data I/O capacitance Symbol CAD COE CWE CCS CI/O Conditions Max Unit VI/O = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VI/O = 0 V, f = 1.0 MHz 15 pF This parameter is guaranteed by design but not tested. DC CHARACTERISTICS — CMOS COMPATIBLE VCC = 5.0V, VSS = 0V, -55°C ≤ TA ≤ +125°C Parameter Input Leakage Current Output Leakage Current VCC Active Current for Read (1) VCC Active Current for Program or Erase (2) VCC Standby Current Output Low Voltage Output High Voltage Output High Voltage Low VCC Lock-Out Voltage Symbol ILI ILO ICC1 ICC2 ICC3 VOL VOH1 VOH2 VLKO Conditions VCC = 5.5, VIN = GND to VCC VCC = 5.5, VIN = GND to VCC CS# = VIL, OE# = VIH CS# = VIL, OE# = VIH VCC = 5.5, CS# = VIH, f = 5MHz IOL = 8.0 mA, VCC = 4.5 IOH = -2.5 mA, VCC = 4.5 IOH = -100 µA, VCC = 4.5 Min Max 10 10 35 50 1.6 0.45 Unit µA µA mA mA mA V V V V 0.85 x VCC VCC - 0.4 3.2 NOTES: 1. The ICC current listed includes both the DC operating current and the frequency dependent component (at 5 MHz). The frequency component typically is less than 2 mA/MHz, with OE# at VIH. 2. ICC active while Embedded Algorithm (program or erase) is in progress. 3. DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V AC TEST CIRCUIT I OL Current Source AC TEST CONDITIONS Parameter Input Pulse Levels Input Rise and Fall Input and Output Reference Level Output Timing Reference Level Typ VIL = 0, VIH = 3.0 5 1.5 1.5 Unit V ns V V D.U.T. C eff = 50 pf VZ 1.5V (Bipolar Supply) I OH Current Source Notes: VZ is programmable from -2V to +7V. IOL & IOH programmable from 0 to 16mA. Tester Impedance Z0 = 75 Ω. VZ is typically the midpoint of VOH and VOL. IOL & IOH are adjusted to simulate a typical resistive load circuit. ATE tester includes jig capacitance. White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 2 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs VCC = 5.0V, VSS = 0V, -55°C ≤ TA ≤ +125°C Parameter Write Cycle Time Chip Select Setup Time Write Enable Pulse Width Address Setup Time Data Setup Time Data Hold Time Address Hold Time Chip Select Hold Time Write Enable Pulse Width High Duration of Byte Programming Operation (min) Sector Erase Time Read Recovery Time before Write VCC Set-up Time Chip Programming Time Output Enable Setup Time Output Enable Hold Time (1) NOTES: 1. For Toggle and Data# Polling. WMF128K8-XXX5 AC CHARACTERISTICS – WRITE/ERASE/PROGRAM OPERATIONS, WE# CONTROLLED Symbol tAVAV tWC tELWL tCS tWLWH tWP tAVWH tAS tDVWH tDS tWHDX tDH tWHAX tAH tWHEH tCH tWHWL tWPH tWHWH1 tWHWH2 tGHWL tVCS tOES tOEH -50 Min 50 0 25 0 25 0 40 0 20 14 2.2 0 50 0 10 Max Min 60 0 30 0 30 0 45 0 20 14 2.2 0 50 0 10 -60 Max Min 70 0 35 0 30 0 45 0 20 14 2.2 0 50 0 10 -70 Max Min 90 0 45 0 45 0 45 0 20 14 2.2 0 50 0 10 -90 Max -120 Min 120 0 50 0 50 0 50 0 20 14 2.2 0 50 0 10 Max -150 Min 150 0 50 0 50 0 50 0 20 14 2.2 0 50 0 10 Max Unit 60 60 60 60 60 12.5 12.5 12.5 12.5 12.5 ns ns ns ns ns ns ns ns ns µs 60 sec ms µs 12.5 sec ns ns AC CHARACTERISTICS – READ ONLY OPERATIONS VCC = 5.0V, VSS = 0V, -55°C ≤ TA ≤ +125°C Parameter Read Cycle Time Address Access Time Chip Select Access Time OE# to Output Valid Chip Select to Output High Z (1) OE# High to Output High Z (1) Output Hold from Address, CS# or OE# Change, whichever is First NOTES: 1. Guaranteed by design, but not tested Symbol tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX tRC tACC tCE tOE tDF tDF tOH -50 Min 50 Max 50 50 25 20 20 0 -60 Min 60 Max 60 60 30 20 20 0 -70 Min 70 Max 70 70 35 20 20 0 -90 Min 90 Max 90 90 40 25 25 0 -120 Min 120 Max 120 120 50 30 30 0 -150 Min 150 Max 150 150 55 35 35 0 Unit ns ns ns ns ns ns ns White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 3 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs VCC = 5.0V, VSS = 0V, -55°C ≤ TA ≤ +125°C Parameter Write Cycle Time WE# Setup Time CS# Pulse Width Address Setup Time Data Setup Time Data Hold Time Address Hold Time WE# Hold from WE# High CS# Pulse Width High Duration of Programming Operation Duration of Erase Operation Read Recovery before Write Chip Programming Time WMF128K8-XXX5 AC CHARACTERISTICS – WRITE/ERASE/PROGRAM OPERATIONS,CS# CONTROLLED Symbol tAVAV tWLEL tELEH tAVEL tDVEH tEHDX tELAX tEHWH tEHEL tWHWH1 tWHWH2 tGHEL tWC tWS tCP tAS tDS tDH tAH tWH tCPH -50 Min 50 0 25 0 25 0 40 0 20 14 2.2 0 12.5 60 -60 Max Min 60 0 30 0 30 0 45 0 20 14 2.2 0 12.5 60 -70 Max Min 70 0 35 0 30 0 45 0 20 14 2.2 0 12.5 60 -90 Max Min 90 0 45 0 45 0 45 0 20 14 2.2 0 12.5 60 -120 Max Min 120 0 50 0 50 0 50 0 20 14 2.2 0 12.5 60 -150 Min 150 0 50 0 50 0 50 0 20 14 2.2 0 12.5 60 Max Max Unit ns ns ns ns ns ns ns ns ns µs sec ns sec White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 4 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs AC WAVEFORMS FOR READ OPERATIONS WMF128K8-XXX5 tDF tOH Addresses Stable tRC tOE tACC tCE CS# Addresses WE# OE# White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 5 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com Outputs High Z Output Valid High Z White Electronic Designs WMF128K8-XXX5 WRITE/ERASE/PROGRAM OPERATION, WE# CONTROLLED tOH tDF tRC tOE Data# Polling tAH tWHWH1 PA tAS tWPH tDH 5555H tGHWL tWC tWP tCS A0A0H PD D7 # PA DOUT NOTES: 1. PA is the address of the memory location to be programmed. 2. PD is the data to be programmed at byte address. 3. D7# is the output of the complement of the data written to each chip. 4. DOUT is the output of the data written to the device. 5. Figure indicates last two bus cycles of four bus cycle sequence. CS# OE# Addresses WE# tDS White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 6 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com 5.0 V Data tCE White Electronic Designs WMF128K8-XXX5 AC WAVEFORMS CHIP/SECTOR ERASE OPERATIONS SA 2AAAH 5555H 5555H 2AAAH 5555H tWP AAAAH tDS tWPH tAS tGHWL tCS tDH 5555H tAH 8080H AAAAH 5555H 1010H/3030H OE# WE# CS# NOTE: 1. SA is the sector address for Sector Erase. White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 7 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com Addresses Data VCC tVCS White Electronic Designs WMF128K8-XXX5 AC WAVEFORMS FOR DATA# POLLING DURING EMBEDDED ALGORITHM OPERATIONS t DF t OH High Z I/O7 and I/O15 Valid Data I/O0-15 Valid Data tWHWH 1 or 2 Data I/O0-6 and I/O8-14 I/O0-6 and I/O8-14 Invalid t OE t OE t CH tOEH tCE White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 8 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com WE# OE# CS# I/O7 and I/O15 I/O7 # and I/O15 # White Electronic Designs WMF128K8-XXX5 ALTERNATE CS# CONTROLLED PROGRAMMING OPERATION TIMINGS Data# Polling t AH tWHWH1 PA tAS tGHEL tCP tCPH tDH A0H 5555H tWC tWS PD WE# OE# CS# tDS Addresses D7 # PA DOUT NOTES: 1. PA represents the address of the memory location to be programmed. 2. PD represents the data to be programmed at byte address. 3. D7# is the output of the complement of the data written to each chip. 4. DOUT is the output of the data written to the device. 5. Figure indicates the last two bus cycles of a four bus cycle sequence. White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 9 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com 5.0 V Data White Electronic Designs PACKAGE 101: 32 LEAD, CERAMIC SOJ WMF128K8-XXX5 21.1 (0.830) ± 0.25 (0.010) 0.2 (0.008) ± 0.05 (0.002) 3.96 (0.156) MAX 0.89 (0.035) Radius TYP 11.3 (0.442) ± 0.30 (0.012) 9.55 (0.376) ± 0.25 (0.010) 1.27 (0.050) ± 0.25 (0.010) PIN 1 IDENTIFIER 1.27 (0.050) TYP 19.1 (0.750) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES PACKAGE 220: 32 LEAD, CERAMIC FLATPACK 20.83 (0.820) ± 0.25 (0.010) 2.60 (0.102) MAX PIN 1 IDENTIFIER 10.41 (0.410) ± 0.13 (0.005) 10.16 (0.400) ± 0.51 (0.020) 0.43 (0.017) ± 0.05 (0.002) 0.127 (0.005) + 0.05 (0.002) – 0.025 (0.001) 1.27 (0.050) TYP 19.05 (0.750) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 10 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs WMF128K8-XXX5 PACKAGE 221: 32 LEAD, FORMED CERAMIC FLATPACK 3.35 (0.132) MAX 20.83 (0.820) ±0.25 (0.010) 0.15 (0.006) TYP 1.27 (0.050) TYP 10.41 (0.410) ±0.13 (0.005) + + 13.47 (0.530) ±0.13 (0.005) 0.43 (0.017) ±0.05 (0.002) 0°/ -4° 0.63 (0.025) TYP 1.27 (0.050) TYP 19.05 (0.750) TYP 1.52 (0.060) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES PACKAGE 300: 32 PIN, CERAMIC DIP, SINGLE CAVITY SIDE BRAZED 42.4 (1.670) ± 0.4 (0.016) 15.04 (0.592) ± 0.3 (0.012) 4.34 (0.171) ± 0.79 (0.031) PIN 1 IDENTIFIER 3.2 (0.125) MIN 0.84 (0.033) ± 0.4 (0.014) 2.5 (0.100) TYP 1.27 (0.050) ± 0.1 (0.005) 0.46 (0.018) ± 0.05 (0.002) 0.25 (0.010) ± 0.05 (0.002) 15.25 (0.600) ± 0.25 (0.010) ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 11 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs WMF128K8-XXX5 PACKAGE 601: 32 PIN, RECTANGULAR CERAMIC LEADLESS CHIP CARRIER 7.62 (0.300) TYP 3.81 (0.150) TYP 5.08 (0.200) TYP 0.56 (0.022) 0.71 (0.028) 10.16 (0.400) TYP PIN 1 0.38 (0.015) x 45° PIN 1 IDENTIFIER 11.25 (0.443) 11.60 (0.457) 1.63 (0.064) 2.54 (0.100) 13.79 (0.543) 14.15 (0.557) 1.02 (0.040) x 45° 3 PLACES 32PinCLCCpkgdim.eps ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 12 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs ORDERING INFORMATION WMF128K8-XXX5 W M F 128K8 - XXX X X 5 X LEAD FINISH: Blank = Gold plated leads A = Solder dip leads VPP PROGRAMMING VOLTAGE 5 = 5V DEVICE GRADE: Q = MIL-STD-883 Compliant M = Military Screened I = Industrial C = Commercial PACKAGE TYPE: DE = 32 Lead Ceramic SOJ (Package 101) C = 32 Pin Ceramic DIP (Package 300) FE = 32 Lead Ceramic Flatpack (Package 220) FF = 32 Lead Formed Ceramic Flatpack (Package 221) CL = 32 Pin rectangular Ceramic Leadless Chip Carrier (Package 601) ACCESS TIME (ns) ORGANIZATION, 128K x 8 Flash MONOLITHIC WHITE ELECTRONIC DESIGNS CORP. -55°C to +125°C -40°C to +85°C 0°C to +70°C White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 13 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs DEVICE TYPE 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic WMF128K8-XXX5 SECTOR SIZE 16KByte 16KByte 16KByte 16KByte 16KByte SPEED 150ns 120ns 90ns 70ns 60ns PACKAGE 32 pin DIP (C) 32 pin DIP (C) 32 pin DIP (C) 32 pin DIP (C) 32 pin DIP (C) SMD NO. 5962-96690 01HYX 5962-96690 02HYX 5962-96690 03HYX 5962-96690 04HYX 5962-96690 05HYX 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 16KByte 16KByte 16KByte 16KByte 16KByte 150ns 120ns 90ns 70ns 60ns 32 lead SOJ (DE) 32 lead SOJ (DE) 32 lead SOJ (DE) 32 lead SOJ (DE) 32 lead SOJ (DE) 5962-96690 01HXX 5962-96690 02HXX 5962-96690 03HXX 5962-96690 04HXX 5962-96690 05HXX 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 16KByte 16KByte 16KByte 16KByte 16KByte 150ns 120ns 90ns 70ns 60ns 32 lead Flatpack (FE) 32 lead Flatpack (FE) 32 lead Flatpack (FE) 32 lead Flatpack (FE) 32 lead Flatpack (FE) 5962-96690 01HTX 5962-96690 02HTX 5962-96690 03HTX 5962-96690 04HTX 5962-96690 05HTX 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 128K x 8 Flash Monolithic 16KByte 16KByte 16KByte 16KByte 16KByte 150ns 120ns 90ns 70ns 60ns 32 lead Formed Flatpack (FF) 32 lead Formed Flatpack (FF) 32 lead Formed Flatpack (FF) 32 lead Formed Flatpack (FF) 32 lead Formed Flatpack (FF) 5962-96690 01HUX 5962-96690 02HUX 5962-96690 03HUX 5962-96690 04HUX 5962-96690 05HUX White Electronic Designs Corp. reserves the right to change products or specifications without notice. April 2001 Rev. 5 14 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com