WMF512K8-70DEC5A

White Electronic Designs WMF512K8-XXX5 512Kx8 MONOLITHIC FLASH, SMD 5962-96692 FEATURES Access Times of 60, 70, 90, 120, 150ns Packaging • 32 pin, Hermetic Ceramic, 0.600" DIP (Package 300) • 32 lead, Hermetic Ceramic, 0.400" SOJ (Package 101) • 32 pin, Rectangular Ceramic Leadless Chip Carrier (Package 601) • 32 lead Flatpack (Package 220) 1,000,000 Erase/Program Cycles Minimum Sector Erase Architecture • 8 equal size sectors of 64K bytes each • Any combination of sectors can be concurrently erased. Also supports full chip erase Organized as 512Kx8 Commercial, Industrial and Military Temperature Ranges 5 Volt Programming. 5V ± 10% Supply. Low Power CMOS Embedded Erase and Program Algorithms TTL Compatible Inputs and CMOS Outputs Page Program Operation and Internal Program Control Time. Note: For programming information refer to Flash Programming 4M5 Application Note. This product is subject to change without notice. Pin Configuration For WMF512K8-XXX5 32 DIP 32 CSOJ 32 Flatpack Pin Configuration For WMF512K8-XCLX5 32 CLCC Top View A12 A18 A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS Top View WE# A15 A16 A18 VCC WE# A17 A14 A13 A8 A9 A11 OE# A10 CS# I/O7 I/O6 I/O5 I/O4 I/O3 I/O1 I/O2 I/O3 I/O4 I/O5 Pin Description A0-18 I/O0-7 CS# OE# WE# VCC VSS Address Inputs Data Input/Output Chip Select Output Enable Write Enable +5.0V Power Ground White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 1 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com I/O6 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 4 3 2 1 32 31 30 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 5 29 6 28 7 27 8 26 25 9 10 24 11 23 12 22 13 21 14 15 16 17 18 19 20 A14 A13 A8 A9 A11 OE# A10 CS# I/O7 A17 VCC White Electronic Designs ABSOLUTE MAXIMUM RATINGS (1) Parameter Operating Temperature Supply Voltage (VCC) (1) Signal Voltage Range(any pin except A9) (2) Storage Temperature Range Lead Temperature (soldering, 10 seconds) Data Retention Mil Temp Endurance - erase/program cycles (Mil Temp) A9 Voltage for sector protect (VID) (3) -55 to +125 -2.0 to +7.0 -2.0 to +7.0 -65 to +150 +300 20 100,000 min -2.0 to +14.0 Unit °C V V °C °C years cycles V Parameter Supply Voltage Input High Voltage Input Low Voltage Operating Temp. (Mil.) Operating Temp. (Ind.) A9 Voltage for Sector Protect WMF512K8-XXX5 RECOMMENDED OPERATING CONDITIONS Symbol VCC VIH VIL TA TA VID Min 4.5 2.0 -0.5 -55 -40 11.5 Max 5.5 VCC + 0.5 +0.8 +125 +85 12.5 Unit V V V °C °C V NOTES: 1. Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs may overshoot VSS to -2.0 V for periods of up to 20ns. Maximum DC voltage on output and I/O pins is VCC + 0.5V. During voltage transitions, outputs may overshoot to Vcc + 2.0 V for periods of up to 20ns. 3. Minimum DC input voltage on A9 pin is -0.5V. During voltage transitions, A9 may overshoot Vss to -2V for periods of up to 20ns. Maximum DC input voltage on A9 is +13.5V which may overshoot to 14.0 V for periods up to 20ns. CAPACITANCE TA = +25°C Parameter Address Input capacitance Output Enable capacitance Write Enable capacitance Chip Select capacitance Data I/O capacitance Symbol CAD COE CWE CCS CI/O Conditions Max Unit VI/O = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VIN = 0 V, f = 1.0 MHz 15 pF VI/O = 0 V, f = 1.0 MHz 15 pF This parameter is guaranteed by design but not tested. DC CHARACTERISTICS — CMOS COMPATIBLE VCC = 5.0V, VSS = 0V, -55°C ≤ TA ≤ +125°C Parameter Input Leakage Current Output Leakage Current VCC Active Current for Read (1) VCC Active Current for Program or Erase (2) VCC Standby Current Output Low Voltage Output High Voltage Low VCC Lock-Out Voltage Symbol ILI ILOx32 ICC1 ICC2 ICC4 VOL VOH1 VLKO Conditions VCC = 5.5, VIN = GND to VCC VCC = 5.5, VIN = GND to VCC CS# = VIL, OE# = VIH, f = 5MHz CS# = VIL, OE# = VIH VCC = 5.5, CS# = VIH, f = 5MHz IOL = 8.0 mA, VCC = 4.5 IOH = -2.5 mA, VCC = 4.5 Min Max 10 10 50 60 1.6 0.45 4.2 Unit µA µA mA mA mA V V V 0.85 x VCC 3.2 NOTES: 1. The ICC current listed includes both the DC operating current and the frequency dependent component (at 5 MHz). The frequency component typically is less than 2 mA/MHz, with OE# at VIH. 2. ICC active while Embedded Algorithm (program or erase) is in progress. 3. DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 2 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs VCC = 5.0V, VSS = 0V, -55°C ≤ TA ≤ +125°C Parameter Write Cycle Time Write Enable Setup Time Chip Select Pulse Width Address Setup Time Data Setup Time Data Hold Time Address Hold Time Chip Select Pulse Width High Duration of Byte Programming Operation (1) Sector Erase Time (2) Read Recovery Time Chip Programming Time WMF512K8-XXX5 AC CHARACTERISTICS – WRITE/ERASE/PROGRAM OPERATIONS,CS# CONTROLLED Symbol tAVAV tWLEL tELEH tAVEL tDVEH tEHDX tELAX tEHEL tWHWH1 tWHWH2 tGHEL 0 11 tWC tWS tCP tAS tDS tDH tAH tCPH -60 Min 60 0 40 0 40 0 40 20 300 15 0 -70 Max Min 70 0 45 0 45 0 45 20 300 15 0 11 -90 Max Min 90 0 45 0 45 0 45 20 300 15 0 11 -120 Max Min 120 0 50 0 50 0 50 20 300 15 0 11 -150 Min 150 0 50 0 50 0 50 20 300 15 11 Max Max Unit ns ns ns ns ns ns ns ns µs sec ns sec Chip Erase Time (3) NOTES: 1. Typical value for tWHWH1 is 7µs. 2. Typical value for tWHWH2 is 1sec. 3. Typical value for Chip Erase time is 8sec. 64 64 64 64 64 sec AC TEST CIRCUIT I OL Current Source AC Test Conditions Parameter Input Pulse Levels Input Rise and Fall Input and Output Reference Level Output Timing Reference Level VZ 1.5V (Bipolar Supply) Typ VIL = 0, VIH = 3.0 5 1.5 1.5 Unit V ns V V D.U.T. C eff = 50 pf I OH Current Source Notes: VZ is programmable from -2V to +7V. IOL & IOH programmable from 0 to 16mA. Tester Impedance Z0 = 75 Ω. VZ is typically the midpoint of VOH and VOL. IOL & IOH are adjusted to simulate a typical resistive load circuit. ATE tester includes jig capacitance. White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 3 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs VCC = 5.0V, -55°C ≤ TA ≤ +125°C Parameter Write Cycle Time Chip Select Setup Time Write Enable Pulse Width Address Setup Time Data Setup Time Data Hold Time Address Hold Time Write Enable Pulse Width High Duration of Byte Programming Operation (1) Sector Erase Time (2) Read Recovery Time before Write VCC Set-up Time Chip Programming Time Output Enable Setup Time Output Enable Hold Time (4) Chip Erase Time (3) NOTES: 1. Typical value for tWHWH1 is 7µs. 2. Typical value for tWHWH2 is 1sec. 3. Typical value for Chip Erase time is 8sec. 4. For Toggle and Data# Polling. WMF512K8-XXX5 AC CHARACTERISTICS – WRITE/ERASE/PROGRAM OPERATIONS, WE# CONTROLLED Symbol tAVAV tELWL tWLWH tAVWH tDVWH tWHDX tWHAX tWHWL tWHWH1 tWHWH2 tGHWL tWC tCS tWP tAS tDS tDH tAH tWPH -60 Min 60 0 40 0 40 0 40 20 Max Min 70 0 45 0 45 0 45 20 -70 Max Min 90 0 45 0 45 0 45 20 -90 Max -120 Min 120 0 50 0 50 0 50 20 Max -150 Min 150 0 50 0 50 0 50 20 Max Unit ns ns ns ns ns ns ns ns µs sec ms µs sec ns ns sec 300 15 tVCS tOES tOEH 0 50 11 0 10 64 0 10 0 50 300 15 0 50 11 0 10 64 300 15 0 50 11 0 10 64 300 15 0 50 11 0 10 64 300 15 11 64 AC CHARACTERISTICS – READ ONLY OPERATIONS VCC = 5.0V, -55°C ≤ TA ≤ +125°C -60 Parameter Read Cycle Time Address Access Time Chip Select Access Time Output Enable to Output Valid Chip Select to Output High Z (1) Output Enable High to Output High Z (1) Output Hold from Address, CS# or OE# Change, whichever is First NOTES: 1. Guaranteed by design, but not tested -70 Max Min 70 60 60 35 20 20 70 70 35 20 20 0 Max -90 Min 90 90 90 35 20 20 0 Max -120 Min 120 120 120 50 30 30 0 Max -150 Min 150 150 150 55 35 35 0 Max Unit Symbol Min tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX tRC tACC tCE tOE tDF tDF tOH 0 60 ns ns ns ns ns ns ns White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 4 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs AC WAVEFORMS FOR READ OPERATIONS tRC Addresses tACC CS# Addresses Stable WMF512K8-XXX5 tDF OE# tOE WE# tCE tOH High Z Outputs High Z Output Valid WRITE/ERASE/PROGRAM OPERATION, WE# CONTROLLED Data# Polling Addresses 5555H tWC CS# tGHWL OE# tWP WE# tCS tWPH tDH Data tDS tOH A0H PD tOE tDF tWHWH1 tAS PA tAH PA tRC I/O7# I/OOUT 5.0 V tCE NOTES: 1. PA is the address of the memory location to be programmed. 2. PD is the data to be programmed at byte address. 3. I/O7# is the output of the complement of the data written to the device. 4. I/OOUT is the output of the data written to the device. 5. Figure indicates last two bus cycles of four bus cycle sequence. White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 5 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs WMF512K8-XXX5 AC WAVEFORMS CHIP/SECTOR ERASE OPERATIONS tAH Addresses 5555H tAS CS# tGHWL OE# tWP WE# tWPH tCS Data tDS tDH 2AAAH 5555H 5555H 2AAAH SA AAH 55H 80H AAH 55H 10H/30H VCC tVCS NOTES: 1. SA is the Sector Address for Sector Erase. AC WAVEFORMS FOR DATA# POLLING DURING EMBEDDED ALGORITHM OPERATIONS t CH t DF t OE OE# tOEH WE# CS# tCE t OH High Z I/O7 Data I/O0-6 tWHWH 1 or 2 I/O7# I/O7 = Valid Data I/O0-6 = Invalid t OE I/O0-7 Valid Data White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 6 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs WMF512K8-XXX5 ALTERNATE CS# CONTROLLED PROGRAMMING OPERATION TIMINGS Data# Polling Addresses 5555H tWC WE# tGHEL OE# tCP CS# tWS tWHWH1 tAS PA tAH PA tCPH tDH Data tDS A0H PD I/O7# I/OOUT 5.0 V Notes: 1. PA represents the address of the memory location to be programmed. 2. PD represents the data to be programmed at byte address. 3. I/O7# is the output of the complement of the data written to the device. 4. I/OOUT is the output of the data written to the device. 5. Figure indicates the last two bus cycles of a four bus cycle sequence. White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 7 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs PACKAGE 101: 32 LEAD, CERAMIC SOJ WMF512K8-XXX5 21.1 (0.830) ± 0.25 (0.010) 0.2 (0.008) ± 0.05 (0.002) 3.96 (0.156) MAX 0.89 (0.035) Radius TYP 11.3 (0.442) ± 0.30 (0.012) 9.55 (0.376) ± 0.25 (0.010) 1.27 (0.050) ± 0.25 (0.010) PIN 1 IDENTIFIER 1.27 (0.050) TYP 19.1 (0.750) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES PACKAGE 220: 32 LEAD, CERAMIC FLATPACK 20.83 (0.820) ± 0.25 (0.010) 2.60 (0.102) MAX PIN 1 IDENTIFIER 10.41 (0.410) ± 0.13 (0.005) 10.16 (0.400) ± 0.51 (0.020) 0.43 (0.017) ± 0.05 (0.002) 0.127 (0.005) + 0.05 (0.002) – 0.025 (0.001) 1.27 (0.050) TYP 19.05 (0.750) TYP ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 8 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs WMF512K8-XXX5 PACKAGE 300: 32 PIN, CERAMIC DIP, SINGLE CAVITY SIDE BRAZED 42.4 (1.670) ± 0.4 (0.016) 15.04 (0.592) ± 0.3 (0.012) 4.34 (0.171) ± 0.79 (0.031) PIN 1 IDENTIFIER 3.2 (0.125) MIN 0.84 (0.033) ± 0.4 (0.014) 2.5 (0.100) TYP 1.27 (0.050) ± 0.1 (0.005) 0.46 (0.018) ± 0.05 (0.002) 0.25 (0.010) ± 0.05 (0.002) 15.25 (0.600) ± 0.25 (0.010) ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 9 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs WMF512K8-XXX5 PACKAGE 601: 32 PIN, RECTANGULAR CERAMIC LEADLESS CHIP CARRIER 7.62 (0.300) TYP 3.81 (0.150) TYP 5.08 (0.200) TYP 0.56 (0.022) 0.71 (0.028) 10.16 (0.400) TYP PIN 1 0.38 (0.015) x 45° PIN 1 IDENTIFIER 11.25 (0.443) 14.15 (0.557) 1.63 (0.064) 2.54 (0.100) 13.79 (0.543) 14.15 (0.557) 1.02 (0.040) x 45° 3 PLACES ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 10 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs ORDERING INFORMATION WMF512K8-XXX5 W M F 512K 8 - XXX X X 5 X WHITE ELECTRONIC DESIGNS CORP. MONOLITHIC Flash ORGANIZATION, 512K x 8 ACCESS TIME (ns) PACKAGE TYPE: C = 32 Pin Ceramic DIP (Package 300) CL = 32 Pin Rectangular Ceramic Leadless Chip Carrier (Package 601) DE = 32 Lead Ceramic SOJ (Package 101) FE = 32 Lead Flatpack (Package 220) DEVICE GRADE: M = Military Screened I = Industrial C = Commercial -55°C to +125°C -40°C to +85°C 0°C to +70°C VPP PROGRAMMING VOLTAGE 5 = 5V LEAD FINISH: Blank = Gold plated leads A = Solder dip leads White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 11 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs DEVICE TYPE SECTOR SIZE 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 64KByte 64KByte 64KByte 64KByte WMF512K8-XXX5 SPEED 150ns 120ns 90ns 70ns PACKAGE 32 pin DIP (C) 32 pin DIP (C) 32 pin DIP (C) 32 pin DIP (C) SMD NO. 5962-96692 01HXX 5962-96692 02HXX 5962-96692 03HXX 5962-96692 04HXX 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 64KByte 64KByte 64KByte 64KByte 150ns 120ns 90ns 70ns 32 lead SOJ (DE) 32 lead SOJ (DE) 32 lead SOJ (DE) 32 lead SOJ (DE) 5962-96692 01HYX 5962-96692 02HYX 5962-96692 03HYX 5962-96692 04HYX 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 64KByte 64KByte 64KByte 64KByte 150ns 120ns 90ns 70ns 32 lead Flatpack (FE) 32 lead Flatpack (FE) 32 lead Flatpack (FE) 32 lead Flatpack (FE) 5962-96692 01HUX 5962-96692 02HUX 5962-96692 03HUX 5962-96692 04HUX 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 512K x 8 Flash Monolithic 64KByte 64KByte 64KByte 64KByte 150ns 120ns 90ns 70ns 32 lead Flatpack (FF) 32 lead Flatpack (FF) 32 lead Flatpack (FF) 32 lead Flatpack (FF) 5962-96692 01HTX 5962-96692 02HTX 5962-96692 03HTX 5962-96692 04HTX White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 12 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs Document Title 512K x 8 Flash Monolithic WMF512K8-XXX5 Revision History Rev # Rev 1 History Initial Release Changes (Pg. 1) 1.1 Change status to Final Changes (Pg. 1) 1.1 Correct typo of Ceramic Changes (Pg. 10) 1.1 Remove pedestal from Flatpack package drawing Changes (Pg. 1) 1.1 Change name from ‘FP’ to Flatpack Changes (Pg. 1, 2, 3, 4, 13) 2.1 Change number of max program/erases to 1,000,000 2.2 Change temperature of max program/erases to 25C 2.3 Absolute Maximum Ratings Table: 2.3.1 Change Data Retention to 20years 2.3.2 Change Endurance to 100,000 cycles minimum 2.4 Write/Erase/Program Operations Tables: 2.4.1 Change tWHWH1 to 300µs 2.4.2 Add Note (1) Typical tWHWH1 = 7µs 2.4.3 Change tWHWH2 to 15sec 2.4.4 Add Note (2) Typical tWHWH2 = 1 sec 2.4.5 Change Chip Programming Time to 11 sec 2.4.6 Change Chip Erase Time too 64 sec 2.4.7 Add Note (3) Chip Erase Time = 8 sec 2.5 Ordering Information 2.5.1 Change Company Name to White EDC 2.6 Change Title Style to new WEDC look Changes (Pg. 1, 2, 10, 12, 13) 3.1 Change package 206 to package 220 3.2 Remove temperature range notice for Endurance 3.3 Change width spec to 0.457" minimum for package 601 Changes (Pg. 1, 3, 4) 4.1 Add 60ns speed grade option Changes (Pg. 1, 11, 13) 5.1 Add 'T' case outline for 'FF' package Changes (Pg. 1, 13) 6.1 Change revision history Rev 2.4.1 to 300 µs 6.2 Change revision history Rev 2.4.2 to 7µs Release Date September 1996 May 1997 February 1998 April 1998 February 1999 Status Preliminary Final Final Final Final Rev 2 May 1999 Final Rev 3 May 1999 Final Rev 4 January 2003 Final Rev 5 Rev 6 April 2005 November 2005 Final Final White Electronic Designs Corp. reserves the right to change products or specifications without notice. November 2005 Rev. 6 13 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com