0211360000

SAK-series 124 SAK-series Weidmüller terminal - SAK-series- are proved in millions of applications for more than 50 years. TS 32 TS 35 Thermosetting plastic or Thermoplastic Terminal of thermosetting plastic are normally used in applications where high continuous service temperature and high flammability level are necessary. The Weidmüller thermosetting plastic KRG is very resistant against infection through mould and micro-organisms. The thermoplastic material Polyamide 66 has very good electrical and mechanical properties upto 100 °C. PA66 is flexible and unsusceptible to fracture, even with low temperatures. Polyamid 66 has improved fire resistance and is self-extinguishing with flammability level V2 according to UL 94. Cross-connection systems SAK portfolio 40% of all terminals are cross-connected for potential branching. • • • • • Weidmüller distinguishes between the following cross-connection units for SAKseries: • type Q pre-assembled cross-connections • type QL permanent cross-connections • type VL removeable cross-connection straps • type QS removeable cross-connection plugs An extensive assortment of accessories is available for Weidmüller SAK terminals: The following approvals apply to SAK terminals: Thermosetting plastic Accessories Cross-connection systems from the SAK and AKZ series, type Q, QL or VL or other freely accessible live components, must be protected with appropriate covers ADP 1 or 4 or TSK 31.5 as long as they are to be inserted safe from contact. Approvals Thermoplastic Feed-through terminals Protective conductor terminals Fuse terminals Disconnect-test terminals Feed-through terminals with tab, solder, WireWrap and Termi Point connections • Initiator terminals, Actuator terminals • Stud terminals a r # q i LR u DNV UL-USA CSA-Canada GOST-Russia SEV-Switzerland KEMA-Netherlands Lloyds Register of Shipping Germanischer Lloyd Det Norske Veritas • • • • • • • • Partitions Cover plates Small partitions Test plugs Test adapters Marking material Cross-connections and Covers Positioning of end plates or partitions between cross-connections Operating voltage Terminal width (in mm) 36 38 10 125 V ~ AP – – 250 V ~ AP – – 380 V ~ AP AP – 440 V ~ TW AP AP 500 V ~ TW TW AP 660 V ~ TW TW TW 750 V ~ TW TW TW In PA terminals small partitions (TSch) have to be used up to 380 V. 12 18 22 – – – AP AP TW TW – – – AP AP TW TW – – – – – AP AP 125 SAK-series Available for the two rail systems TS32 and TS35, the SAK terminals are useable for every application and for all cross-sections. SAK terminals fulfill the requirements of EN 60 947-7-1. Feed-through terminals SAKD 2.5 N SAKD 2.5/10/35 SAK 2.5/35 SAK 2.5/10/35 Y SAK 2.5 SAK 2.5/10 SAK 4/35 SAK 4/10/35 Y W W W Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version KrG Blue KrG KrS PA Blue PA Orange PA Terminal block with marking PA Terminal block without marking PA End plate (thickness mm) a r # LR u 5/32.5/43.5 5/44/38 10/M 2.5/3.5 x 0.6 6/45/40 10/M 2.5/3.5 x 0.6 10/M 2.5/3.5 x 0.6 ari# 6.5/40/51.5 6.5/45/44 12/M 3/3.5 x 0.6 500 V/24 A/2.5 mm2 6 kV/3 800 V/24 A/2.5 mm2 8 kV/3 800 V/24 A/2.5 mm2 3) 8 kV/3 800 V/32 A/4 mm2 8 kV/3 0.4…0.6 1 0.4…0.6 1 0.4…0.6 1 0.5…1.0 2 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A2 30 A/4 mm2 0.5…6 0.5…2.5 0.5…4 0.5…2.5/43) A3 32 A/4 mm2 0.5…6 0.5…2.5 0.5…4 0.5…2.5/43) A3 32 A/4 mm2 0.5…6 0.5…4 0.5…4 0.5…4 A4 41 A/6 mm2 24 24 32 32 36 300 V/20 A/28…12 AWG 300 V/20 A/22…12 AWG Y Qty. W Qty. 600 V/20 A/22…12 AWG 600 V/25 A/26…10 AWG W Cat. No. Qty. 0380420000 100 0380470000 100 600 V/20 A/22…12 AWG 600 V/36 A/26…10 AWG W Cat. No. Qty. 0443620000 100 0443670000 100 0215560000100 0268860000 100 03804600001)100 03804800001)100 600 V/20 A/22…12 AWG 600 V/25 A/26…10 AWG Y Cat. No. Qty. 0279620000 100 0279670000 100 0279630000 100 02796600001)2)100 02796800001)2)100 13263600001)2)100 03225600001)2) 10 03228600001)2) 10 Type Cat. No. Qty. AP (1.5) 0279520000 20 AP (1.5) 0279570000 20 AP (1.5) 0279530000 20 0215580000100 0268880000100 0401060000 10 0523160000 10 0401160000 10 Type KrG Blue KrG KrS PA Blue PA PA Blue PA Partition (thickness mm) TW WTW KrG Blue KrG KrS PA Blue PA HP a r i # LR u AP (1.5) AP (1.5) Cat. No. 0150960000 0150980000 Qty. 20 20 TW (1.5) TW (1.5) TW (1.5) 0191860000 0191880000 0307500000 20 20 20 TSch 3 0366860000 100 Q Q Q Q 0367800000 0367900000 0368000000 0368100000 50 50 50 20 Small partition TSch 1 Cross-connection Q4 2-pole 3-pole 4-pole 10-pole 2 3 4 10 Type AP (1.5) AP (1.5) AP (1.5) AP (1.5) AP (1.5) TW TW TW TW TW TW (2.5) (2.5) (2.5) (1.5) (1.5) (1.0) a r i # LR u DNV 6/36.5/46.5 04994600001) 10 04995600001) 10 Cat. No. Qty. 0279520000 20 0279570000 20 0279530000 20 0460560000 20 0460580000 20 0302820000 0302870000 0302830000 0302860000 0302880000 0297100000 20 20 20 20 20 20 AP (1.5) AP (1.5) 0279560000 0279580000 20 20 TW TW TW TW TW TW 0302820000 0302870000 0302830000 0302860000 0302880000 0297100000 20 20 20 20 20 20 (2.5) (2.5) (2.5) (1.5) (1.5) (1.0) TSch 1 0319160000 100 TSch 1 0319160000 100 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 50 50 50 20 AD 4 0303400000 BSKM3x22 0128900000 50 100 2 3 4 10 50 50 50 20 2 3 4 10 Type AP (1.5) AP (1.5) AP (1.5) AP (1.5) AP (1.5) 04436600001) 04436800001) 13236600001) 05304600001) 05303600001) Cat. No. 0117920000 0117970000 0117930000 0117960000 0117980000 TW TW TW TW TW TW 0130120000 0103170000 0130130000 0130160000 0130180000 0197100000 20 20 20 20 20 20 TSch 1 0319160000 100 Q Q Q Q 0336700000 0336800000 0336900000 0368800000 50 50 50 20 (2.5) (2.5) (2.5) (1.5) (1.5) (1.0) 2 3 4 10 100 100 100 10 10 Qty. 20 20 20 20 20 Cover plates AD 4 0303400000 50 BSKM3x22 0128900000 100 Switchable cross-connection link VL 2 BS VH Marking tags DEK Print Standard DEK 5 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” AD 4 0285300000 50 BSK M3x22 0128900000 100 VL 2 VH BS 0197000000 0285100000 0292500000 100 50 100 DEK6.5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 1) 2) 126 Contact-proof with ADP 4 cover profile (see section “Accessories”) Not suitable for SST 3 safety pin 3) Cat. No. 0279660000, 0279680000, 0380460000 and 0380480000, 41 A for 6 mm2 Feed-through terminals DK 4 Q* DKB4 Q*/10* Y Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 With/without plastic insulating collar mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Technical data Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version KrG Blue KrG KrS PA Blue PA Orange PA Terminal block with marking PA Terminal block without marking PA End plate (thickness mm) KrG Blue KrG KrS PA Blue PA PA Blue PA Partition (thickness mm) TW WTW KrG Blue KrG KrS PA Blue PA HP Small partition TSch 6 Switchable cross-connection link VL 2 BS 2-pole 3-pole 4-pole 10-pole 2-pole 3-pole 4-pole VH Marking tags DEK Print Standard Y Y W W a r i # LR u DNV 6.5/40/51.5 ar# 6/54/60 6/54/60.5 9/M 3/3.5 x 0.6 ar# 6/54/60 6/54/60.5 9/M 3/3.5 x 0.6 800 V/32 A/4 mm2 8 kV/3 500 V/2 x 32 A/4 mm2 6 kV/3 500 V/2 x 32 A/4 mm2 6 kV/3 0.5…1.0 2 0.5…1.0 2 0.5…1.0 2 0.5…6 0.5…4 0.5…4 0.5…4 0.5…4 0.5…4 0.5…4 0.5…4 0.5…4 0.5…4 A4 41 A/6 mm2 0.5…4 A3 32 A/4 mm2 0.5…4 A3 32 A/4 mm2 36 32 32 32 32 600 V/20 A/22…12 AWG 600 V/36 A/26…10 AWG Y Cat. No. Qty. 0128320000 100 0128370000 100 0128330000 100 01283600001)2)100 01283800001)2)100 01050600001)2)100 03226600001)2) 10 03088600001)2) 10 Type Cat. No. Qty. AP (1.5) 0117920000 20 AP (1.5) 0117970000 20 AP (1.5) 0117930000 20 AP (1.5) 0117960000 20 AP (1.5) 0117980000 20 300 V/27 A/22…12 AWG 300 V/10 A/26…12 AWG Y Qty. W Qty. 300 V/27 A/22…12 AWG 300 V/10 A/26…12 AWG Y Qty. W Qty. 0590060000*1)100 05901600001) 100 0355460000100 0527660000100 0590080000*1)100 05901800001)100 0355480000100 0527680000100 TW TW TW TW TW TW (2.5) (2.5) (2.5) (1.5) (1.5) (1.0) TSch 1 Cross-connection Q4 QB 4 DK 4 DK4/35 Q Q Q Q 0130120000 0103170000 0130130000 0130160000 0130180000 0197100000 20 20 20 20 20 20 0319160000 100 SAK-series SAK 4 SAK 4/10 1323860000*1) 10 Type AP (1.5) AP (1.5) Cat. No. Qty. Type Cat. No. Qty. 1397160000 1397180000 20 20 AP (1.5) AP (1.5) 1397160000 1397180000 20 20 WTW (Ex) 1058800000 20 WTW (Ex) 1058800000 20 TSch 6 0190260000 100 TSch 6 0190260000 100 2 3 4 10 0336700000 0336800000 0336900000 0368800000 50 50 50 20 Q2 Q3 Q4 Q 10 QB 2 QB 3 QB 4 0336400000 50 0336500000 50 0336600000 50 0368600000 20 0482700000**100 0482800000** 50 0482900000** 50 Q2 Q3 Q4 Q 10 QB 2 QB 3 QB 4 0336400000 50 0336500000 50 0336600000 50 0368600000 20 0482700000**100 0482800000** 50 0482900000** 50 VL 2 VH BS 0197000000 0285100000 0292500000 100 50 100 VL 2 VH BS 0446700000 50 1056500000 100 0343100000 100 VL 2 VH BS 0446700000 50 1056500000 100 0343100000 100 DEK 6.5 see “Accessories” DEK6 see “Accessories” DEK6 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” * Accepts LS 2.8 shield lugs Cat. No. 1056400000 ** 2.5 mm2 conductor connection when using QB 1) 2) Contact-proof cross-connec. with ADP 4 over profile (see “Accessories”) Not suitable for fuse pin SST 3 127 Feed-through terminals DK4 QV* DK4 QV/35* Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 With/without plastic insulating collar mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version KrG Blue KrG KrS PA Blue PA Orange PA Terminal block with marking Terminal block without marking End plate (thickness mm) AP Partition (thickness mm) TW WTW Small partition KrG Blue KrG KrS PA Blue PA TSch 6 Cross-connection Q4 QB 4 2-pole 3-pole 4-pole 10-pole SAK 10 SAK 10/10/35 Y Y Y W W W SAK 16 SAK 16/35 Y W ar# 6/54/60 6/54/60.5 9 mm/M 3/3.5 x 0.6 a r i # LR u DNV 8/40/51.5 8/45/44 12 mm/M 3.5/4.0 x 0.8 a r i # LR u DNV 10/40/51.5 10/45/44 12 mm/M 4/5.5 x 1.0 a r i # LR u DNV 12/50/57.5 12/50/50 15 mm/M 4/5.5 x 1.0 500 V/32 A/4 mm2 6 kV/3 800 V/41 A/6 mm2 8 kV/3 800 V/57 A/10 mm2 8 kV/3 1000 V/76 A/16 mm2 8 kV/3 0.5…1.0 2 0.8…1.6 3 1.2...2.03) 4 1.2…2.4 4 0.5…4 0.5…4 0.5…4 0.5…10 0.5…6 0.5…10 1.5…10 2.5…16 1.5…10 2.5…10 4…162) 4…16 0.5…4 A3 32 A/4 mm2 0.5…6 A5 1.5…10 B6 76 A/16 mm2 4…16 B6 32 32 41 57 300 V/27 A/22…12 AWG 300 V/10 A/26…12 AWG Y Qty. W Qty. 600 V/40 A/22…8 AWG 600 V/47 A/20…8 AWG Y Qty. W Qty. 600 V/60 A/14…6 AWG3) 600 V/65 A/14…6 AWG3) Y Qty. W Qty. 600 V/80 A/12…4 AWG 600 V/87 A/10…4 AWG Y Qty. W Qty. 0193220000100 0380520000100 0110020000 100 0443720000 100 0271020000 50 0380620000 50 0380570000100 0110070000 100 0443770000 100 76 0193230000100 0110030000 100 0271030000 50 0590260000*1)1000363660000*1)100 01932600001)10003805600001)100 01100600001)100 04437600001) 100 02710600001)50 03806600001)50 0590280000*1)1000363680000*1)100 01932800001)10003805800001)100 01100800001)100 04437800001) 100 02710800001)50 03806800001)50 03227600001) 10 05538600001) 10 03089600001) 10 Type KrG Blue KrG KrS PA Blue PA SAK 6 N SAK 6/10/35 AP (1.5) AP (1.5) Cat. No. Qty. 1397160000 1397180000 WTW (Ex) 1058800000 20 20 20 TW (2.0) TSch 6 0607000000 0190260000 20 100 Q2 Q3 Q4 Q 10 QB 2 QB 3 QB 4 0336400000 0336500000 0336600000 0368600000 0482700000** 0482800000** 0482900000** 50 50 50 20 100 50 50 03531600001) 10 Type AP (1.5) AP (1.5) AP (1.5) AP (1.5) AP (1.5) Cat. No. 0117920000 0117970000 0117930000 0117960000 0117980000 Qty. 20 20 20 20 20 Type AP (1.5) AP (1.5) AP (1.5) AP (1.5) AP (1.5) Cat. No. 0117920000 0117970000 0117930000 0117960000 0117980000 Qty. 20 20 20 20 20 Type AP (3.0) Cat No. 0271120000 Qty. 20 AP (3.0) AP (1.5) AP (1.5) 0271130000 0271160000 0271180000 20 20 20 TW (1.5) 0130120000 20 20 20 20 20 20 100 20 20 20 20 20 20 100 0281120000 0130130000 0130160000 0130180000 0197100000 0319160000 0130120000 0130170000 0130130000 0130160000 0130180000 0197100000 0319160000 TW (3.0) TW (1.5) TW (1.5) TW (1.5) TW (1.5) TSch 1 TW (1.5) TW (1.5) TW (1.5) TW (1.5) TW (1.5) TW (1.5) TSch 1 TW (3.0) TW (1.5) TW (1.5) TW (2.0) TSch 1 0281130000 0303660000 0303680000 0607000000 0319160000 20 10 10 20 100 Q Q Q Q 0456700000 0456800000 0456900000 0457000000 50 50 50 20 Q Q Q Q 0457100000 0457200000 0457300000 0457400000 50 50 50 20 Q Q Q Q 2 3 4 10 0457500000 0457600000 0457700000 0457800000 50 50 50 20 0518200000 50 2 3 4 10 2 3 4 10 Cover AD 4 0303400000 BSK M 2.5 x18 0303300000 Switchable cross-connection link VL 2 BS VH Marking tags DEK Print Standard 50 AD 4 0196600000 50 BSKM3x22 0128900000 100 AD 4 0178600000 50 BSKM3x22 0128900000 100 AD 4 VL 2 VH BS 0135900000 0285100000 0292500000 VL 2 VH BS 0135800000 0285100000 0292500000 DEK 5 see “Accessories” DEK 5 see “Accessories” BSKM3x22 0128900000 100 100 VL 2 VH BS 04467000000 50 10565000000 100 03431000000 100 VL 2 VH BS 0194700000 0285100000 0292500000 50 50 100 DEK 6 see “Accessories” DEK 8 see “Accessories” 50 50 100 50 50 100 Mounting rails, end brackets, further marking material see “Accessories” * Accepts LS 2.8 shield lugs Cat. No.1056400000 ** 2.5 mm2 conductor connection when using QB 128 1) Contact-proof with ADP 4 cover profile (see section “Accessories”) 2) Tightening torque for 16 mm2 stranded: 2 Nm 3) Tightening torque for 16 mm2 and AWG6: 2 Nm Feed-through terminals Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version KrG Hexagon socket KrG Hexagon socket Blue KrG KrS Hexagon socket KrS PA Hexagon socket PA Blue PA End plate (thickness mm) KrG Blue KrG KrS PA Blue PA Orange PA SAK 35 SAK 35/35 SAK 70 SAK 70/35 SAK 95 SAK 95/35 Y Y Y Y W W W W a r # u DNV 16/58/67.5 16/63/60 18 mm/M 6/6.5 x 1.2 a r i # LR u DNV 18/58/67.5 18/58/60 20 mm/M 6/6.5 x 1.2 a r # LR u DNV 22/75/79.5 22/75/87 24 mm/M 8/S 6 D911 a r # DNV 28/83.5/100.5 28/83.5/96.5 30 mm/M 10/S 8 D6911 1000 V/125 A/35 mm2 8 kV/3 800 V/125 A/35 mm2 8 kV/3 1000 V/192 A/70 mm2 8 kV/3 1000 V/232 A/95 mm2 8 kV/3 4.0…5.0/4.0…6.0*** 4.0…5.0/4.0…6.0*** 6.0…12.0 10.0…20.0 2.5…16 2.5…50 2.5…35 2.5…35 B8 125 A/35 mm2 65 65 6…16 16…50 10…35 10…35 B9 125 A/35 mm2 99 99 Strips 16 3x9x0.8 16…70 1) 6x9x0.8 16…70 1) 6x13x0.5 16…35 B 11 192 A/70 mm2 180 10…16 10…120 2) 10…95 2) 10…35 B 12 232 A/95 mm2 180 600 V/100 A/12…2 AWG 600 V/120 A/12…2 AWG Y Qty. W Qty. 600 V/100 A/6…2 AWG 600 V/145 A/6…2 AWG Y Qty. W Qty. 0303520000 20 0476520000 20 600 V/145 A/4…2/0 AWG 600 V/150 A/4…2/0 AWG Y VPEW Qty. 600 V/190 A/6…3/0 AWG 600 V/260 A/6…3/0 AWG Y Qty. W Qty. 0340820000 10 0340870000 10 0550520000 10 0662220000 10 0550620000 20 0608220000 20 0555720000 20 0608320000 20 0608370000 20 0550630000 20 Strips 3x9x0.8 6x9x0.8 6x13x0.5 6x16x0.8 0303530000 20 0340830000 10 0555730000 20 0550660000 20 0608260000 20 0303560000 20 0380760000 20 0555760000 20 0608360000 20 0476560000 20 0582460000 20 013916000010 0303580000 20 0380780000 20 Type AP (3.0) AP (3.0) AP (3.0) AP (1.5) AP (3.0) Cat. No. Qty. 0303620000 10 0303670000 10 0303630000 10 0303660000 10 0303680000 10 Type AP (3.0) AP (3.0) AP (3.0) AP (1.5) AP (3.0) Cat. No. Qty. 0303620000 10 0303670000 10 0303630000 10 0303660000 10 0303680000 10 TW (3.0) 0304320000 10 TW (3.0) 0304320000 10 TW (3.0) TW (1.5) 0304330000 10 0304360000 10 TW (3.0) TW (1.5) 0304330000 10 0304360000 10 QL 2 QL 3 QL 4 QL 10 VH 17 BS M 4x30 SS M 4 0564900000 50 0565000000 50 0565100000 50 0565200000 20 0267000000 50 0267100000 50 0136400000100 QL 2 QL 3 QL 4 QL 10 VH 17 BS M 4x30 SS M 4 0123600000 20 0123700000 20 0123800000 20 0338600000 20 0267000000 50 0267100000 50 0136400000100 VL 2 VH 24.5 BS M 4x35 0124000000 50 0298700000 50 0298900000 50 Type AP (4.0) Cat. No. Qty. 0340920000 10 Type AP (3.0) AP (3.0) Cat. No. Qty. 0550920000 10 0550970000 10 AP (4.0) AP (2.0) 0340930000 10 0340960000 10 QL 2 QL 3 0345300000 20 0167000000 20 QL 2 QL 3 QL 4 0551200000 10 0407600000 10 0407700000 10 VH 30.5 BS M 5x45 SS M 5 0345500000 20 0345600000 20 0346100000100 VH 35 BS M 5x50 0551100000 10 0630200000 20 Partition (thickness mm) KrG Blue KrG KrS PA Blue PA Cross-connection QL 3 VH BS SS Switchable cross-connection link VL 2 BS 2-pole 3-pole 4-pole 10-pole VH Cover / test plug PS 4 Marking tags DEK Print Standard AD 4 0576700000 50 BSK M 4x32 0129100000 50 PS 4 0299600000 20 AD 4 0178700000 20 BSK M 4x32 0129100000 50 PS 4 0299600000 20 AD 3 0344300000 10 BSKM 5x45 0344400000 50 PS 4 0299600000 20 ADP 3 0485400000 20 PS 4 0299600000 20 DEK 5 DEK 5 DEK 5 DEK 5 see “Accessories” see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” *** For hexagon socket 1) 2) see “Accessories” see “Accessories” 12 Nm for 70 mm2 20 Nm for 95 mm2 and 120 mm2 129 SAK-series SAK 35 N SAK 35 N/35 Feed-through terminals (spring-loaded) RSF 3 RSF 3/35 RSF 1 Disconnect test terminal Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Version PA KrG End plate/partition/small partition AP TW TSch 1 VH r 8/50/60 8/50/53 12 mm ar 11/50/60 11/77/72.5 12 mm 12 mm 630 V/32 A 4 6 kV / 3 500 V/57 A 10 6 kV / 3 500 / 41 A 6 6 kV / 3 0.5…10 0.5…10 0.75...16 0.75...10 0.5…1.0 2 0.5…4 0.5…4 UL CSA Ordering data Cross-connection QL Y Y Y Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/-current Rated cross-section mm2 Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 RSF 2 SS PA KrG PA HP HP PA 2-pole 3-pole 4-pole 10-pole BS M 3 x ... Switchable cross-connection link VH 21 Y Qty. W Qty. 0497560000 50 9501160000 50 0497520000 50 Y Qty. W Qty. 0270320000 50 Type Cat. No. Y Qty. Y Qty. 0623320000*200623120000**20 Type AP (3) Cat. No. Qty. 0270460000 10 Qty. AP (3) 0270420000 10 TW (1.5) TW (2) TW (0.5) TSch 1 3877960000 10 3833500000 20 0474700000 20 0319160000100 TW (2) TW (0.5) 3833500000 20 0474700000 20 QL 2 QL 3 QL 4 QL 10 VH 13.5 0194300000 50 0194400000 50 0194500000 50 0338300000 10 0248500000100 QL 2 QL 3 QL 4 QL 10 VH 17.5 0194300000 0194400000 0194500000 0338300000 0285200000 BS M 3x20 0303000000 100 BS M 3x25 SS QS 4 0292500000 100 0164400000 50 0369760000 10 VH 2 VH 21 BS M 3x20 SS 0194700000 50 0309600000100 0296200000 50 0164400000 50 VH 2 VH 27 BS M 3x25 SS 0528400000 0309400000 0309800000 0164400000 50 50 50 10 50 Type AP (3.0) QL QL QL QL 2 3 4 10 Cat. No. Qty. 0301420000 0267400000 0267500000 0267600000 0341700000 10 50 50 50 20 BS M 4x6 SB 14 0149700000 100 0135300000100 BST 1 3878060000 20 PS 4 StB 17 0299600000 20 0147100000 50 50 50 50 50 Dummy plug made from plastic, to keep the place of an extracted plug Test plug/socket PS StB Cover plate Marking tags PS 2.3 StB 14 0180400000 50 0168600000 50 PS 2.4 StB 18 0299600000 20 0286500000 20 ADP 2 0485300000 1 ADP 2 0485300000 1 DEK see “Accessories” DEK see “Accessories” Plug-testsocket (QL cannot be used) Print Standard * with disconnector (73 mm height) ** Disconnector with handle (86 mm height) 130 Feed-through terminals for thermocouples Busbars made from thermocouple materials according to DIN IEC 584 SAK 2.5 TC DK 4 Q/TC Y Weidmüller’s thermocouple-treminals are specially designed for transmitting the smallest voltages in temperature measuring circuits. Special busbars ensure that no false signals occur in the terminal when temperature differences exist in the positive and negative path. This high measuring precision is necessary for, e.g. test beds, air craft engines, for complicated chemical processes, controls, etc. W Y Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Technical data/VDE Rated voltage/current/cross-section Tightening torque range Nm 6/36.5/49.5 10 mm/M 2.5/3.5 x 0.6 6/54/59.5 6/54/60.5 9 mm/M 3/3.5 x 0.6 –/–/2.5 mm2 –/–/4 mm2 0.4…0.6 0.5…1 1 Thermocouple (sensor) 4 Reference point 2 Thermocouple terminals 5 Supply conductors (to and from) SAK-series I. Configuration of a temperature measuring circuit Ordering data 3 Compensation conductor 6 Measuring device The thermocouple terminals displayed in this measurement circuit are used to thermoelectrically transmit thermal e.m.f. of the thermocouple to the reference point and indicating device via the thermocouple. Version NiCr Ni CuNi Fe Cu NiCr/Ni Cu/CuNi Fe/CuNi Type a) Type J Fe (positive leg) CuNi (negative leg) b) Type T Cu (positive leg) CuNi (negative leg) c) Type K NiCr (positive leg) Ni (negative leg) W Y Qty. 1284160000 1338260000 100 1285660000 1338160000 100 1284060000 1338060000 100 Type KrG Blue KrG KrS PA Blue PA Orange PA Terminal Cat. No. Qty. 0107260000100 0107160000100 0189860000100 0190060000100 0189960000100 K T J End plate (thickness mm) II. Symbols Thermocouples according to IEC 584 DIN 43710 Y Cat. No. Qty. AP (1.5) 0279560000 20 TW (1.5) 0302860000 20 Type AP (1.5) Cat. No. Qty. 1397160000 20 Partition (thickness mm) KrG Blue KrG KrS PA WEM for TS 32 HP Busbar material trade name WTW (Ex)e 1058800000 20 TW HP (2.0) 0607000000 20 Iron Constantan Copper Constantan Chromel Alumel Marking tags DEK Print Standard DEK 6 see “Accessories” DEK 6 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 131 Feed-through terminals Terminals/Accessories SAKG 28 I SAKG 28 II Y The Weidmüller SAKG range offers the following connection variants: • clamping yoke/flat lug as a combination, Version I. • flat lug, Version II. Two types of threading are provided here. a) screw set with lock nut b) with thread in busbar • clamping yoke connection, Version III. The stripped conductor can be connected without further preparation. Versions Version I Version II without thread Version II G with thread Version III Cables with cable lugs are connected to SAKG terminals of Version I and to SS stud terminals. Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data End plate, hard paper 0205100000 0205200000 tropic-proof ar#u 28/70/63.5 a r # u DNV 28/70/53 15 mm/M 6/– –/M 6/– 1000 V*/125 A/35 mm2 8 kV/3 1000 V*/125 A/35 mm2 8 kV/3 3…6 3…6 6…35 6…35 10…35 6…35 B9 125 A/35 mm2 (QL 2) 125 125 A/35 mm2 (QL 2) 125 600 V/95 A/2 AWG 600 V/110 A/6…1 AWG Y Cat. No. Qty. 0170020000 10 600 V/115 A/2 AWG 600 V/110 A/6…1 AWG Y Cat. No. Qty. 0170320000 10 Y EP 1 (2) EP 1 (2) W Fitting instructions for SAKG terminals When tightening the clamping screw, it is recommended that the conductor be held against the direction of tightening to prevent deformation of the mounting rail and so as not to place the terminal foot under undue torsional forces. UL CSA Type KrG Y Cat. No. Qty. 0205100000 10 0205200000 10 Cat. No. Qty. Y EP 1 (2) EP 1 (2) W Cat. No. Qty. 0205100000 10 0205200000 10 Cat. No. Qty. 0180700000, 0205300000 0180800000, 0205400000 tropic-proof Partition, hard paper (thickness in mm) 0151400000 0164600000 tropic-proof 0177100000 B/L/H (incl. TS 32) mm 0179900000 B/L/H (incl. TS 35) mm TW 1 (2) TW 1 (2) Y Qty. 0151400000 10 0164600000 10 2/120/75.5 TW 1 (2) TW 1 (2) Y Qty. 0151400000 10 0164600000 10 2/120/75.5 Cross-connection 2-pole 3-pole 4-pole QL 2 QL 3 QL 4 0193900000 5 0407600000 5 0407700000 5 QL 2 QL 3 QL 4 0193900000 0407600000 0407700000 5 5 5 AH 28 0326660000 5 AH 28 0326660000 5 DEK 5 see “Accessories” DEK 5 see “Accessories” Cover Cover To ensure shock protection following connections of conductors, AH covers can be clipped onto the terminal. Marking tags DEK Print Standard Mounting rails, end brackets, further marking material see “Accessories” During conductor connection, observe clearance and creepage distances. Insert partitions if necessary. 132 Feed-through terminals SAKG 28 III SAKG 32 I SAKG 32/35 I Y Y SAKG 32 II SAKG 32/35 II SAKG 32 II G SAKG 32/35 II G Y W Y W Y W SAKG 32 III SAKG 32/35 III Y W 15 mm/M 6/- ar#u 32/87/84 32/87/84.5 26 mm/M 8/- ar#u 32/80/53 32/80/51 -/M 8/- r # u DNV 32/80/53 32/80/53 -/M 8/- ar#u 32/94/84 32/94/84.5 26 mm/M 8/- 1000 V*/125 A/35 mm2 8 kV/3 1000 V*/125 A/35 mm2 8 kV/3 1000 V*/150 A/50 mm2 8 kV/3 1000 V*/150 A/50 mm2 8 kV/3 1000 V*/150 A/50 mm2 8 kV/3 1000 V*/150 A/50 mm2 8 kV/3 3…6 3…6 6…12 6…12 6…12 6…12 6…35 6…35 10…35 6…35 B9 10…70 10…70 10…70 10…35 B 11 150 A/50 mm2 (QL 2) 150 150 A/50 mm2 (QL 2) 150 150 A/50 mm2 (QL 2) 150 600 V/165 A/3 AWG 600 V/170 A/1…2/0 AWG Y Qty. W Qty. 0286620000 0637120000 10 600 V/200 A/3 AWG 600 V/170 A/1…2/0 AWG Y Qty. W Qty. 0170420000 10 063732000010 600 V/170 A/1…2/0 AWG Y Qty. W Qty. 0185120000 10 0637420000 10 r#u 28/70/53 ar#u 28/70/63.5 -/M 6/- 125 A/35 mm2 (QL 2) 125 600 V/110 A/6…1 AWG Y Cat. No. Qty. 0185020000 10 Y EP 1 (2) EP 1 (2) W TW 1 (2) TW 1 (2) Cat. No. Qty. 0205100000 10 0205200000 10 Cat. No. Qty. Y Qty. 0151400000 10 0164600000 10 2/120/75.5 600 V/95 A/2 AWG 600 V/135 A/8…2 AWG Y Cat. No. Qty. 0170820000 10 Y EP 1 (2) EP 1 (2) W TW 1 (2) TW 1 (2) 0193900000 0407600000 0407700000 5 5 5 AH 28 0326660000 5 DEK 5 see “Accessories” 600 V/165 A/3 AWG 600 V/185 A/1…2/0 AWG Y Qty. W Qty. 0286720000 10 0637220000 10 Cat. No. Qty. 0205100000 10 0205200000 10 Y EP 1 (2) EP 1 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 1 (2) EP 1 (2) Cat. No. Qty. 0205100000 10 0205200000 10 Y EP 1 (2) EP 1 (2) Cat. No. Qty. 0205100000 10 0205200000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Cat. No. W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W EP 1/35 (2) EP 1/35 (2) Cat. No. Qty. 0180700000 10 0180600000 10 W EP 1/35 (2) EP 1/35 (2) Cat. No. Qty. 0180700000 10 0180600000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 TW 1 (2) TW 1 (2) Y + W Qty. 0151400000 10 0164600000 10 TW 1 (2) TW 1 (2) Y + W Qty. 0151400000 10 0164600000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 Qty. Y Qty. 0151400000 10 0164600000 10 2/120/75.5 QL 2 QL 3 QL 4 10…70 10…70 10…70 10…35 B 11 150 A/50 mm2 2/160/90.5 2/160/90.5 AH 28 0326660000 DEK 5 see “Accessories” 5 2/120**/75.5 2/120**/75.5 2/160/90.5 2/160/90.5 2/120**/75.5 2/120**/75.5 QL 2 QL 3 QL 4 0194000000 0441500000 0441600000 5 5 5 QL 2 QL 3 QL 4 0194000000 0441500000 0441600000 5 5 5 QL 2 QL 3 QL 4 0194000000 0441500000 0441600000 5 5 5 AH 32 0326760000 5 AH 32 0326760000 5 AH 32 0326760000 5 DEK 5 see “Accessories” DEK 5 see “Accessories” DEK 5 see “Accessories” AH 32 DEK 5 0326760000 5 see “Accessories” * During conductor connection, observe clearance and creepage distances. Insert partitions if nececssary ** For Cat. No. 0180600000 and 0180700000: length = 160 mm. 133 SAK-series SAKG 28 II G Feed-through terminals SAKG 70 II G SAKG 70/35 II G SAKG 40 I SAKG 40/35 I Y W Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version KrG End plate, hard paper (thickness mm) 0205100000, 0180500000 0205200000, 0180600000 tropic-proof 0180700000, 0205300000 0180800000, 0205400000tropic-proof Partition, hard paper (thickness mm) 0151400000 0164600000 tropic-proof 0177100000 B/L/H (incl. TS 32) mm 0179900000 B/L/H (incl. TS 35) mm SAKG 40 II SAKG 40/35 II SAKG 40 II G SAKG 40/35 II G Y W W Y W r # u DNV 32/84/54 32/84/53 –/M 8/– ar#u 40/95/84 46/95/85.5 27 mm/M 10/– a r # u DNV 40/90/53 46/90/53 –/M 10/– r#u 40/90/55 46/90/55 –/M 10/– 1000 V*/192 A/70 mm2 8 kV/3 1000 V*/232 A/95 mm2 8 kV/3 1000 V*/232 A/95 mm2 8 kV/3 1000 V*/232 A/95 mm2 8 kV/3 6…12 10...20 10…20 10…20 192 A/90 mm2 (QL 2) 192 10…95 10…95 10…95 10…35 B 12 232 A/95 mm2 (QL 2) 232 232 A/95 mm2 (QL 2) 232 232 A/95 mm2 (QL 2) 232 600 V/200 A/2/0…4/0 AWG Y Qty. W Qty. 0150420000 10 0636620000 10 600 V/195 A/4/0 AWG 600 V/250 A/2/0…4/0AWG Y Qty. W Qty. 028682000010 0637520000 5 600 V/230 A/4/0 AWG 600 V/250 A/2/0…4/0 AWG Y Qty. W Qty. 017052000010 0637720000 5 600 V/230 A/4/0 AWG 600 V/250 A/2/0…4/0 AWG Y Qty. W Qty. 0185220000 10 0637820000 5 Y EP 1 (2) EP 1 (2) Cat. No. Qty. 0205100000 10 0205200000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 W EP 1/35 (2) EP 1/35 (2) Cat. No. Qty. 0180500000 10 0180600000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 TW 1 (2) TW 1 (2) Y + W Qty. 0151400000 10 0164600000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 2/120/75.5 2/120/75.5 Cross-connection 2/160/90.5 2/160/90.5 Y + W Qty. 0194000000 10 0441500000 10 0441600000 10 2-pole, QL 2 3-pole, QL 3 4-pole, QL 4 Y Q t y. W 2/160/90.5 2/160/90.5 Qty. Y 2/160/90.5 2/160/90.5 Qty. W Qty. Y Qty. W Qty. 0194100000 10 0211400000 10 0194100000 10 0211400000 10 0194100000 10 0211400000 10 0263500000 10 0444900000 10 0263500000 10 044490000010 0263500000 10 0444900000 10 0409800000 10 0445000000 10 0409800000 10 044500000010 0409800000 10 0445000000 10 AH 40 0326860000 5 AH 40 0326860000 5 DEK 5 see “Accessories” DEK 5 see “Accessories” Cover Marking tags DEK Print Standard AH 32 0326760000 5 AH 40 0326860000 5 DEK 5 see “Accessories” DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” *During conductor connection, observe clearance and creepage distances. Insert partitions if necessary. 134 Feed-through terminals SAKG 40 III SAKG 40/35 III SAKG 46 II SAKG 46/35 II Y W SAKG 46 II G SAKG 46/35 II G SAKG 54 II SAKG 54/35 II Y W Y W SAKG 54 II G SAKG 54/35 II G SAKG 46/I AL SAKG 46/II AL Y W Y W Y ar#u 40/100/84 46/100/85.5 27 mm/M 10/– ar#u 46/106/55 46/106/54.5 –/M 12/– r # u DNV 46/106/57.5 46/106/57 –/M 12/– ar#u 54/122/57 54/122/57 –/M 16/– a r # u DNV 54/122/60 54/122/60 –/M 16/– 1000 V*/232 A/95 mm2 8 kV/3 1000 V*/309 A/150 mm2 8 kV/3 1000 V*/309 A/150 mm2 8 kV/3 1000 V*/415 A/240 mm2 8 kV/3 1000 V*/415 A/240 mm2 8 kV/3 1000 V*/309 A/150 mm2 8 kV/3 10…20 14…31 14…31 25…60 25…60 14…31/25…40 46/112/74 23 mm/M 12/M 14/- 50…240 35…185 309 A/150 mm2 309 A/150 mm2 (QL 2) 309 415 A/240 mm2 (QL 2) 415 415 A/240 mm2 (QL 2) 415 600 V/195 A/4/0 AWG 600 V/230 A/2/0…4/0 AWG Y Qty. W Qty. 0286920000 10 0637620000 5 600 V/285 A/4/0 AWG 600 V/365 A/300 MCM Y Qty. W Qty. 0170620000 10 0637920000 5 600 V/285 A/4/0 AWG 600 V/365 A/300 MCM Y Qty. W Qty. 0185320000 10 0638020000 5 600 V/380 A/500 MCM 600 V/600 A/300…500 MCM Y Qty. W Qty. 0170720000 10 0638120000 5 600 V/380 A/500 MCM 600 V/600 A/300…500 MCM Y Qty. W Qty. 0185420000 10 0638220000 5 SAK-series 10…95 10…95 10…95 10…35 B 12 232 A/95 mm2 Y Qty. W 1287920000** 5 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 2 (2) EP 2 (2) Cat. No. Qty. 0205300000 10 0205400000 10 Y EP 2 (2) EP 2 (2) W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W EP 2/35 (2) EP 2/35 (2) Cat. No. Qty. 0180700000 10 0180800000 10 W TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 TW 2 (2) TW 2 (2) Y + W Qty. 0177100000 10 0179900000 10 2/160/90.5 2/160/90.5 2/160/90.5 2/160/90.5 AH 40 0326860000 DEK 5 see “Accessories” 5 2/160/90.5 2/160/90.5 2/160/90.5 2/160/90.5 QL 2 QL 3 QL 4 0247000000 0444400000 0444500000 5 5 5 QL 2 QL 3 QL 4 0247000000 0444400000 0444500000 5 5 5 AH 46 0326960000 5 AH 46 0326960000 5 DEK 5 see “Accessories” DEK 5 see “Accessories” QL 2 QL 3 QL 4 DEK 5 * During conductor connection, observe clearance and creepage distances. Insert partitions if necessary. ** Suitable for connection of 1 aluminium conductor of max 185 mm2 2/160/90.5 2/160/90.5 0264400000 0408000000 0247400000 see “Accessories” 5 5 5 QL 2 QL 3 QL 4 DEK 5 Qty. Cat. No. Qty. 0205300000 10 0205400000 10 Cat. No. Qty. Y Qty. 0177100000 10 0179900000 10 TW 2 (2) TW 2 (2) 2/160/90.5 2/160/90.5 0264400000 0408000000 0247400000 see “Accessories” 5 5 5 QL 2 QL 3 QL 4 0194000000 0441500000 0441600000 5 5 5 AH 46 0326960000 5 DEK 5 see “Accessories” *** Suitable for connection of 2 aluminium conductors of max. 185 mm2 135 Stud terminals KST 5 KST 5/35 KST 6 KST 6/35 KST 8 KST 8/35 21 18 Y W Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version KrG for TS 35 x 7.5 for TS 35 x 15/2.3 PA Hard paper HM HM Width/length/height (incl. TS 32) mm Width/length/height (incl. TS 35) mm W W W 18/40/62 18/49.5/54.5 –/M 6/– ar# 24/60/55 24/62.5/49.5 –/M 5/– ar# 24/60/62 24/62.5/54.5 –/M 6/– ar# 24/60/72 24/62.5/64.5 –/M 8/– 1000 V1)/76 A/16 mm2 6 kV/3 1000 V1)/57 A/10 mm2 8 kV/3 1000 V1)/76 A/16 mm2 8 kV/3 1000 V1)/125 A/35 mm2 8 kV/3 3…6 2…4 3…6 6…12 82 A/16 mm2 65 A/10 mm2 82 A/16 mm2 200 135 A/35 mm2 200 600 V/85 A/12…4 AWG 600 V/65 A/6 AWG Y Qty. W Qty. 0498220000 25 0649820000 25 600 V/50 A/12…6 AWG 600 V/65 A/12…6 AWG 600 V/115 A/12…2 AWG PA PPO KrG PA PA Partition, (thickness mm) 30 25 SS 6 SS 6/35 Y Qty. W Qty. Y Qty. W Qty. 9503370000 25 Cat. No. Qty. TW SS6 (TS32)0455860000 10 Y Qty. W Qty. 9501320000 25 9508230000 25 9528300000 25 9506940000 25 9528310000 25 9506950000 25 9528320000 25 Y+ W Y+ W Y+ W TWHGW (2)(TS 35)0607100000 20 TW right TW left 2) 2/129/93 2/70/62.5 1718530000 10 1752800000 10 2/160/83.5 2/160/78.5 TW right TW left 1718530000 10 1752800000 10 2/160/83.5 2/160/78.5 TW right TW left 1718530000 10 1752800000 10 2/160/83.5 2/160/78.5 Cross-connection 2-pole 3-pole Marking tags DEK Print Standard QL 2 QL 3 0284300000 20 0279000000 20 QL 2 9503390000 DEK 5 see “Accessories” DEK 5 see “Accessories” 1 QL 2 9501350000 DEK 5 see “Accessories” 5 QL 2 9501360000 DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” * Depends on cable lug 136 1) with partition 2) Left AP is required only once at beginning of terminal strip 1 Stud terminals KST 12 KST 12/35 39 37 KST 10 KST 10/35 ar# 34/60/82 34/62.5/74.5 –/M 12/– 1000 V1)/192 A/70 mm2 8 kV/3 1000 V1)/232 A/95 mm2 8 kV/3 10…20 14…31 207 A/70 mm2 200 250 A/95 mm2 200 600 V/175 A/12…2/0 600 V/200 A/12…3/0 Y Qty. W Qty. Y Qty. W SAK-series W W ar# 34/60/82 34/62.5/74.5 –/M 10/– Qty. 9501330000 20 TW right TW left 9506960000 20 9528330000 20 9506970000 20 9528340000 20 Y+ W Y+ W 1718530000 10 1752800000 10 2/160/83.5 2/160/78.5 TW right TW left 1718530000 10 1752800000 10 2/160/83.5 2/160/78.5 QL 2 9501370000 DEK 5 see “Accessories” 1 QL 2 9501380000 DEK 5 see “Accessories” 1 137 PE terminals EK 2.5 N EK 2.5/35 Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-2 Rated voltage/current with PEN/cross-section Rated voltage/rated impulse voltage acc. to VDE 0110/1.89/ pollution severity Further technical data Tightening torque range Nm Clampable conductor Solid H07V-U Stranded H07V-R Flexible H07V-K Fexible H07V-K and ferrule DIN 46 228/1 Cable AWG Plug gauge according to 60 947-7-1 Ordering data mm2 mm2 mm2 mm2 Nr. Size Version Green/yellow PA Blank Two clamping yokes blank Hexagon socket blank Support block EK 4 EK 4/35 Y Y W W EK 6/35 EK 10 EK 10/35 Y W W ar# 6/36.5/49.5 6/56/40 10 mm/M 2.5/3.5 x 0.6 ar#i 8/40/51.5 6.5/56/44 12 mm/M 3/3.5 x 0.6 8/56/44 12 mm/M 3.5/4.0/0.8 ar# 10/40/51.5 10/56/44 12 mm/M 4/5.5 x 1.0 –/–/2.5 mm2 –/–/4 mm2 –/–/6 mm2 –/–/10 mm2 0.4…0.8/0.5…1.0* 0.5…1.0/0.5…1.0* 1.2…1.6/0.5…1.0* 1.2…2.4/0.5…1.0* 0.5…4 0.5…2.5 0.5…4 0.5…2.5 22…14 A3 0.5…6 0.5…4 0.5…4 0.5…4 22…10 A4 0.5…10 1.5…6 0.5…10 0.5…6 20…8 A5 0.5…10 1.5…6 0.5…10 0.5…10 20….8 B6 Y Qty. W Qty. Y Qty. W ar# Qty. 0474360000100 0661060000100 0354560000100 0661160000100 Type SH 2 Cat. No. Qty. 0494920000 10 Type SH 2 Cat. No. 0494920000 DEK 6 see “Accessories” DEK 6.5 see “Accessories” Qty. 10 W Qty. 0661260000100 0354660000 80 0661360000100 Type SH 2 Cat No. Qty. 0494920000 10 Type SH 2 Cat. No. 0494920000 DEK 8 see “Accessories” DEK 5 see “Accessories” Y Qty. W Qty. Qty. 10 For insulation of mounting rails in insulated-earth installations SK - key, 8mm Marking tags DEK Print Standard Mounting rails, end brackets, further marking material see “Accessories” * For centre screw 138 PE terminals EK 35** EK 35/35 Y Y W W EK 2 SAKE 35 SAKE 70 Y Y Y EK 95/35 W ar# 12/50/57.5 12/56/50 16 mm/M 4/5.5 x 1.0 ar# 18/58/67.5 16/58/60 20 mm/M 6/6.5 x 1.2 r# 10/52/38 r# 14/46/39 r# 18/94/59.5 14 mm/M 4/– 16 mm/M 6/– 25 mm/M 8/– 25/76/100/92 25/76/100/92 27 mm/M 10/– –/–/16 mm2 –/–/35 mm2 –/–/10 –/–/35 mm2 –/–/70 mm2 –/–/95 mm2 1.2…2.4/0.8…1.0* 2.5…5.0/ ** 1.2…2.4/2.0…4.0* 2.5…5.0/2.0…4.0* 6.0…12/2.0…4.0* 10.0…20.0/1.2…2.4* 2.5…16 2.5…16 2.5…16 4…16 12…6 B6 6…16 16…50 10…35 10…35 10…2 B9 1.5…10 1.5…10 1.5…10 1.5…10 16…8 B6 6…35 6…35 6…16 10…35 8…2 B8 10…70 10…70 10…70 10…70 6…0 B 10 10…120 10…95 10…95 10…95 6…4/0 B 12 Y Qty. W Qty. 0374660000 50 0190160000 50 Type SH 2 Cat. No. Qty. 0494920000 10 Y Qty. W Qty. 0354760000 20 0661460000 20 Type SH 2 Cat. No. Qty. 0494920000 10 Qty. 20 Y 0323100000 Type Cat. No. Qty. Y Qty. Qty. Y Qty. W Qty. 0144400000 20 0213200000 20 1338300000 10 Type SH 2 Type SH 2 Cat. No. Qty. 0494920000 10 Y W Qty. 0535300000 10 0535400000 10 Cat. No. Qty. 0494920000 10 0235000000 DEK 5 see “Accessories” DEK 5 see “Accessories” ** ADm f. EK 35/35 = 1.2 - 2.4 Nm ADm f. EK 35 = 0.8 - 1.6 Nm 139 SAK-series EK 16 EK 16/35 Fuse terminals ASK 11) ASK 1/351) KDKS 11) KDKS 1/351) W Y Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data/feed through-terminal base Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version PA KrG Beige Wemid End plate/partition (thickness mm) Y W SAKS 1/G25 SAKS 1/35/G25 Y W Y W ar# 8/58/45.5 8/58/44 9 mm/M 3/3.5 x 0.6 a 8/73.5/59,8 8/73.5/55,7 9 mm/M 3/3.5 x 0.6 a r i # DNV 13/54/61 13/54/54 12 mm/M 4/5.5 x 1.0 r i # u DNV 13/54/61 13/54/54 12 mm/M 4/5.5 x 1.0 500 V/6.3 A2)/4 mm2 6 kV/3 500 V/6.3 A/4 mm2 6 kV/3 500 V/6.3 A3)/10 mm2 6 kV/3 500 V/6.3 A3)/10 mm2 6 kV/3 0.5…1.0 2 0.5…1.0 2 1.2…2.4 4 1.2…2.4 4 0.5…4 1.5…4 0.5…4 0.5…4 A3 (QB 2…4) 10 0.5…4 0.5…16 1.5…10 0.5…10 0.5…10 B6 (QL 2…5) 47 (QL 6…10) 36 0.5…16 1.5…10 0.5…10 0.5…10 B6 (QL 2…5) 47 (QL 6…10) 36 300 V/6.3 A/12 max. AWG 300 V/6.3 A/26…12 AWG Y+W Cat.No. Qty. 0474560000 100 300 V/15 A/12 max. AWG 300 V/6.3 A/22…10 AWG 600 V/10 A/26…10 AWG Y Qty. W Qty. 600 V/10 A/26…10 AW Y Qty. W Qty. Type AP (1.5) G-fuse inserts Acc. to IEC 60127-2 (VDE 0820 T.2 Bl 1) rated current (A): Rated voltage 250 V Fast switching capacity 1500 A (at 250 V, 50 Hz, cos ϕ = 0.7) SAKS 1 SAKS 1/35 0.5…4 0.5…4 A4 (QB 2…4) 10 Cat. No. Qty. 0380360000 20 Qty. 9503300000 50 9503310000 50 10 10 10 10 10 10 10 10 0553300000 100 0553300000 100 0430300000 0430400000 0430500000 0430600000 0430700000 0430800000 0430900000 0431000000 Contact sleeve Qty. W Type Cat. No. Qty. AP 1 KDKS 9503330000 25 Wemid 9532470000 25 for Y TW (2.0) 0607000000 20 5 x 20 mm 0430300000 10 0430400000 10 0430500000 10 0430600000 10 0430700000 10 0430800000 10 0430900000 10 0431000000 10 5 x 20 mm 0.10 fast 0.20 fast 0.25 fast 0.50 fast 1.0 fast 1.6 fast 2.0 fast 2.5 fast 3.15 fast 4.0 fast 5.0 fast 6.3 fast Y 0191220000 20 0501620000 20 0191120000 20 050152000020 0501500000 20 Type Cat. No. Qty. AP (2.5) 0191320000 20 Wemid beige 0191300000 20 for Y TW (2.0) 0607000000 20 5 x 20 mm 0430300000 10 0430400000 10 0430500000 10 0430600000 10 0430700000 10 0430800000 10 0430900000 10 0431000000 10 Type Cat. No. Qty. AP (2.5) 0191320000 20 Wemid-beige 0191300000 for Y TW (2.0) 0607000000 20 5 x 25 mm 0.25 (m) 0546900000 10 0.5 (m) 0510300000 10 0.8 (m) 0646400000 10 1 (m) 0265800000 10 10 (m) 0193100000 10 2 (f) 0192700000 10 4 (f) 0192800000 10 6.3 (f) 0192900000 10 Screw cap/disconnector lever (spare) Marking tags DEK Red pull lever Print Standard TH SIHA 0377060000 100 1593020000 100 TH SIHA 0377060000 100 1593020000 100 SK (5 x 20) 0282100000 20 SK (5 x 25) 0282000000 20 DEK 8 see “Accessories” DEK 8 see “Accessories” DEK 5 see “Accessories” DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 1) 140 Multipole interruptable with group marking carrier Sch2 2-pole Cat. No. 1359500000, 1000 mm Cat. No. 0337400000 Fuse terminals KSKM 2 KSKM 2/35 Y KSKM 3 KSKM 3/35 Y Y 13/69/62 13/69/63 12 mm/–/– 13/69/62 13/69/63 12 mm/–/– 13/69/62 13/69/63 12 mm/–/– 250 V/6.3 A1)/10 mm2 250 V/13 A2)/10 mm2 440 V/10 A/10 mm2 0.5…16 0.5…16 0.5…16 0.5…10 0.5…10 0.5…10 B6 B6 B6 600 V/10 A/22…8 AWG 600 V/15 A/22…8 AWG 600 V/15 A/22…8 AWG Y Qty. W Qty. Y Qty. W Qty. 9509570000 20 9509600000 20 9509580000 20 9509610000 20 Type AP (3) Cat. No. Qty. 9509630000 20 Type AP (3) 5 x 20 mm 0.10 (f) 0.20 (f) 0.25 (f) 0.50 (f) 1.00 (f) 1.60 (f) 2.00 (f) 2.50 (f) 3.15 fast 4.0 fast 5.0 fast 6.3 fast 0430300000 0430400000 0430500000 0430600000 0430700000 0430800000 0430900000 0431000000 0431100000 0431200000 0431300000 0431400000 5 x 20 SBL 0446100000 40 DEK 5 1) 2) Cat. No. Qty. 9509630000 20 1 x 1/4” see “Accessories” Y Qty. W SAK-series KSKM 1 KSKM 1/35 Qty. 9509620000 20 Type AP (3) Cat. No. Qty. 9509630000 20 1 1/4 x 1/4” 10 10 10 10 10 10 10 10 10 10 10 10 E E E E E 2A 3A 5A 7A 10 A 0294500000 0295700000 0294600000 0295800000 0293900000 10 10 10 10 10 1 x 1/4" SBL 0446200000 40 1 1/4 x1/4"SBL 0446300000 40 DEK 5 DEK 5 see “Accessories” see “Accessories” Max. fuse rating according to DIN 41 660, IEC 127 CEE4 Type 1 Fuse according to BS 1362 141 Fuse terminals SAKS 3 SAKS 3/35 SAKS 4 SAKS 4/35 Y W Y W SAKS 2 SAKS 2/35 Y W Y W a r # LR u 13/54/61 13/54/55 12 mm/M 4/5.5 x 1 r # LR u 24/75/73 24/75/66 14 mm/M 4/5.5 x 1 r # LR u 28/80/80.5 28/80/66 13 mm/M 4/5.5 x 1 ri#u 28/80/81.5 28/80/75 12 mm/M 4/5.5 x 1 500 V/10 A/10 mm2 6 kV/3 400 V**/16 A/10 mm2 6 kV/3 400 V/63 A***/16 mm2 6 kV/3 500 V/10 (25) A***/10 mm2 6 kV/3 1.2…2.4 4 1.2…2.4 4 1.2…2.4 4 1.2…2.4 4 0.5…16 1.5…10 0.5…10 0.5…10 B6 (QL 2…5) 47 (QL 6…10) 36 0.5…16 1.5…10 0.5…10 0.5…10 B6 (QL 2…5) 47 (QL 6…10) 36 1.5…16 1.5…16 1.5…16 1.5…16 B7 (QL 2…5) 47 (QL 6…10) 36 0.5…16 0.5…10 0.5…10 0.5…10 B6 (QL 2…5) 47 (QL 6…10) 36 UL CSA Version 300 V/10 A/22…10 AWG 600 V/10 A/22…10 AWG Y Qty. W Qty. 600 V/30 A/22…8 AWG Y Qty. W Qty. 600 V/63 A/14…6 AWG Y Qty. W Qty. 600 V/25 A/22…8 AWG Y Qty. W Qty. KrG KrG 02489200003) 20 06675200003)20 0321320000 20 0501820000 20 0359420000 20 0502120000 20 0206820000 20 1368720000 20 Neozed D 01 Type Cat. No. Qty. TW HP (2.0) 0607000000* 20 Neozed D 02 Type Cat. No. Qty. TW HP (2.0) 0607000000*20 Diazed E 16 Type Cat. No. Qty. TW HP (2.0) 0607000000*20 QL QL QL QL QL QL QL QL QL QL QL QL Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data/feed through-terminal base Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data SAKS 5 SAKS 5/35 End plate/partition (thickness mm) PA HP 02975200004) 20 03289200004)20 Type AP (2.5) for Y TW (2.0) Cat. No. Qty. 0191320000 0607000000 Cross-connection QL 0328000000 0328100000 0328200000 0339000000 20 20 20 20 2 3 4 10 0207800000 0207900000 0208000000 0338900000 20 20 20 20 2 3 4 10 0207800000 0207900000 0208000000 0338900000 20 20 20 20 SS Fixing screws for cross-connections Fuse inserts 1 1/4" x 1/4" 2 3 4 10 SS M 4 0136400000100 BS M 4x9 0103300000100 Gauge ring Amp.Colour Cat. No. Qty. P 14/2 pink 0138000000 50 P 14/4brrown 0138100000 50 P 14/6green 0328600000 50 P14/10 red 0328700000 50 SS M 4 0136400000 100 BS M 4x9 0103300000 100 Gauge ring Amp. Colour Cat. No. Qty. P 18/20 Blue 0361800000 P 18/25 yellow0361900000 P 18/35 black 0362000000 P 18/50 white 0362100000 50 50 50 50 Rated voltage 400 V E 14/2 0137400000 E 14/4 0137500000 E 14/6 0328300000 E 14/10 0328400000 E 14/16 0328500000 10 10 10 10 10 Rated voltage 400 V E 18/20 0361300000 E 18/25 0361400000 E 18/35 0361500000 E 18/50 0361600000 E 18/63 0361700000 10 10 10 10 10 SK (5 x 30) 0282000000 20 SK (1/4”x 11/4 ) 0428900000 20 SK 0339410000 20 SK 0359310000 20 SK 0284110000 20 DEK 5 DEK 5 see “Accessories” DEK 5 see “Accessories” DEK 5 see “Accessories” Fuse insert Nominal current (A): 0.5 1.0 2.0 3.0 5.0 7.0 10.0 fast fast fast fast fast fast fast E E E E E E E 0.5 A 1A 2A 3A 5A 7A 10 A 0533800000 0525500000 0294500000 0295700000 0294600000 0295800000 0293900000 G fuse inserts 5 x 30 mm (500 V~/0.032…6.3 A). Available from Wickmann-Werke GmbH, Annastr. 113, 58453 Witten, Germany, Phone ++492302/6620 D fuse inserts SS M 4 0136400000 100 BS M 4x9 0103300000 100 Gauge ring Amp. Colour Cat. No. Qty. P 16/10 red 0208900000 100 P 16/16 grey 0209000000 100 P 16/20 Blue 0209100000 100 Rated voltage 500 V E 10 A 0208500000 E 16 A 0208600000 E 20 A 0208700000 E 25 A 0208800000 25 25 25 25 Screw cap (spare) Marking tags DEK red black Print Standard see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” *only for TS 32 142 ** Also for 440 V~ with neozed marina fuse *** Current for overload up to 10 A, for short circuit up to 25 A 3) 4) For fuse inserts 1 1/4 x 1/4” DEF 63 For fuse inserts 5 x 30 Fuse terminals SAKS 4 USA Fuse terminals with fault indicator ASK 1 LD KDKS 1 Fuse insert 5 x 20 AC model Y W ar 24/75/73 24/75/66 14 mm/M 4/5.5 x 1 mm2 Dimensions/approvals Terminal width (+ 0.2 assembly tolerance) mm Insulation stripping length mm Connection data Screw connection, solid Screw connection, flexible/ferrule with/without plastic collar Conductor cross-section 1.2…2.4 4 0.5…16 1.5…10 0.5…10 0.5…10 B6 (QL 2…5) 47 (QL 6…10) 36 600 V/30 A/20…8 AWG 600 V/30 A/22…8 AWG Y Qty. W Qty. 0162220000 20 0178220000 20 VDE rated data Current Voltage LED-current (24…60 V) LED-current (115…230 V) LED-current (24…230 V) Incandescent lamp-current Neon lamp-current Cross-section Ordering data 10.3 x 38,1 Type Cat. No. Qty. TW HP (2.0) 0607000000*20 QL QL QL QL 2 3 4 10 0328000000 0328100000 0328200000 0339000000 20 20 20 20 ar 8 9 8 9 0.5…4 mm2 0.5…4 mm2 AWG 22…12 0.5…4 mm2 0.5…4 mm2 AWG 22…12 6.3 A 24…230 V (depending on terminal) ≤ 2 mA ≤ 2 mA 6.3 A 24…230 V (depending on terminal) ≤ 2 mA 24 24 48 60 115 230 V– V– V– V– V– V– 4 mm2 Type ASK 1 LD ASK 1 LD ASK 1 LD ASK 1 LD ASK 1 LD ASK 1 LD 24 48 60 115 230 V~ V~ V~ V~ V~ ASK ASK ASK ASK ASK SS M 4 0136400000 100 BS M 4 x 9 0103300000 100 Accessories Mounting rail End brackets (thickness mm) Warning: In the event of a faulty fuse, the connection system is live! for TS 32 Y for TS 35 W End plate/End plate (thickness mm) Cross-connections Type ‘QL’ Cross-connection Type ‘QB’ 1 1 1 1 1 LD LD LD LD LD Cat. No. Qty. 8050810000 25 0222760000 25 0225260000 25 0226460000 25 0225460000 25 0225660000 25 0222860000 0225360000 0226360000 0225560000 0225760000 25 25 25 25 25 4 mm2 Type Cat. No. KDKS 1 8146450000 25 KDKS 1 KDKS 1 8148930000 25 8148920000 25 KDKS 1 KDKS 1 8142840000 25 8148910000 25 Qty. Mountable on TS 32 and TS 35 Mountable on TS 32 and TS 35 TS 32 TS 35x7.5 TS 35x15 EWK 1 EW 35 AP PA (1.5) 0122800000 0383400000 0498000000 0206160000 50 0383560000 50 0380360000 20 TS 32 TS 35x7.5 TS 35x15 0122800000 0383400000 0498000000 EW 35 0383560000 50 QB 21) QB 31) QB 41) 0461100000100 0461200000 50 0461300000 50 QB QB QB QB QB 0461100000 100 0461200000 50 0461300000 50 0545400000 0545300000 TH (spare) 0377060000 100 straight angled 21) 31) 41) 581) 581) Fixing screw (fits QL) Disconnect lever (spare) SK (w. spring) 0161730000 20 DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 1)When using QB, the rated cross-current reduces to max. 2.5 mm2 143 SAK-series 400 V/30 A/10 6 kV/3 DC model Warning: In the event of a faulty fuse, the connection system is live! Fuse terminals with fault indicator SAKS 1 SAKS 4 SAKS 6 SAKS 7 Fuse insert 5 x 20/5 x 25 Fuse insert E14/D 01 Fuse insert 11/4“ x 1/4“ Fuse insert 5 x 20/5 x 25 (e.g. Neozed D 01) acc. to DEF 63 Warning: In the event of a faulty fuse, the connection system is live! Warning: In the event of a faulty fuse, the connection system is live! Warning: In the event of a faulty fuse, the connection system is live! Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Terminal width (+ 0.2 assembly tolerance) mm Insulation stripping length/clamping screw/screwdriver blade Connection data Screw connection, solid Screw connection, flexible Conductor cross-section Further technical data Tightening torque range Torque setting with electric screwdriver type DMS 2 VDE rated data Voltage/current LED-current (24…60 V) LED-current (115…230 V) Incandescent lamp-current Neon lamp-current Cross-section Ordering data Fuse insert 5 x 20 LED Acc. to IEC 60127-2 (VDE 0820 T.2 Bl 1) without indicator Nm ar 24 V– 24 V~ 48 V– 48 V~ 13 12 24 14 12 12 12 12 0.5…16 mm2 0.5…10 mm2 AWG 20…8 0.5…16 mm2 0.5…10 mm2 AWG 20…7 0.5…16 mm2 0.5…10 mm2 AWG 20…8 0.5…16 mm2 0.5…10 mm2 AWG 20…8 1.2…2.4 4 1.2…2.4 4 1.2…2.4 4 1.2…2.4 4 –/10 A ≤ 5 mA –/16 A 500 V~/10 A 10 A ≤ 1 mA 500 V~/10 A 10 A ≤ 1 mA ≤ 1 mA 10 mm2 ≤ 1 mA 10 mm2 ≤ 1 mA 10 mm2 Type Cat. No. Qty. SAKS 6 KrG 0531820000 40 for 11/4“ x 1/4“ acc. to DEF 63 exchangable neon lamps (please order separately) Type Cat. No. Qty. SAKS 7 KrG for 5 x 25 0576120000 40 SAKS 7 KrG for 5 x 20 0573120000 40 exchangable neon lamps (please order separately) Type TS 32 Type TS 32 Y Qty. W Qty. SAKS 1 LD 0371420000 10 0225820000 10 1111220000 10 1111320000 10 0371420000 10 0214020000 10 Type SAKS 4 TS 32 Neon Voltage 115 V0 480 V0 Cat. No. Qty. lamp 0101820000 10 0102120000 10 SAKS 1 GL Incandescent lamp 24 V0 48 V0 ar ar ≤ 50 mA ≤ 0.5 mA 10 mm2 Voltage Warning: In the event of a faulty fuse, the connection system is live! 0173220000 10 0378920000 10 SAKS 1 GL Neon lamp Fuse insert 5 x 25 Acc. to DIN 41576 without indicator 115 V0 230 V0 LED 24 V– Incandescent lamp 48 V0 0385320000 10 8068330000 10 0306120000 10 0199920000 10 SAK 1 LD on demand SAKS GL on demand SAKS 1 GL Neon lamp 115 V0 230 V0 Accessories Mounting rail End brackets (thickness mm) End plate (thickness mm) Cross-connection Type ‘QL’ Cross-connection Type ‘QB’ Fixing screw (fits QL) Screw cap (spare) Neon lamp 144 for TS 32 Y for TS 35 W 0309320000 10 0198620000 10 Type TS 32 TS 35x7.5 TS 35x15 EWK 1 (8.5) EW 35 (8.5) AP KrG (3) Cat. No. Qty. 0122800000 0383400000 0498000000 0206160000 50 0383560000 50 0191320000 20 SK (5 x 20) SK (5 x 25) 0282100000 20 0282000000 100 Type TS 32 Cat. No. Qty. 0122800000 EWK 1 (8.5) 0206160000 50 Cat. No. Qty. 0122800000 Cat. No. Qty. 0122800000 EWK 1 (8.5) 0206160000 50 EWK 1 (8.5) 0206160000 50 AP KrG 0146720000 20 QL 2 0191400000 50 QL 3 0191500000 50 QL 4 0191600000 20 QL 10 0338800000 20 BSM 3x6 m.SS 0346200000 100 AP KrG (3) 0146720000 20 QL 2 0207800000 20 QL 3 0207900000 20 QL 4 0208000000 20 QL 10 0338900000 20 BSM 4x9 m.SS 0133300000 100 Neon lamp 230 V~ 0550300000 Neon lamp 115 V~ 0550200000 Neon lamp 230 V~ 0550300000 Neon lamp 115 V~ 0550200000 Fuse inserts and gauge rings for Weidmüller fuse terminals Fuse inserts for terminal type SAKS 1 SAKS 7 ASK 1 WSI 6 Rated voltage (V) Rated current (A) Size (mm) Type G fuse inserts 5 x 20 without indicator acc. to IEC 60127-2 (VDE 0820 T.2 Bl 1) Cat. No. Qty. 10 10 10 10 10 10 10 10 10 10 10 10 10 0.1 0.2 0.25 0.5 0.63 (F) (F) (F) (F) (F) G G G G G 20/0.10A/F 20/0.20A/F 20/0.25A/F 20/0.50A/F 20/0.63A/F 1.0 1.6 2.0 2.5 3.15 4.0 5.0 6.3 (F) (F) (F) (F) (F) (F) (F) (F) G G G G G G G G 20/1.00A/F 20/1.60A/F 20/2.00A/F 20/2.50A/F 20/3.15A/F 20/4.00A/F 20/5.00A/F 20/6.30A/F 0430300000 0430400000 0430500000 0430600000 0439000000 0430700000 0430800000 0430900000 0431000000 0431100000 0431200000 0431300000 0431400000 5 x 25 m. K.1) Breaking capacity 80 A (at 250 V, 50 Hz, cos : = 1) 0.25 (M) 0.5 (M) 0.8 (M) 250 1 (M) 10 (M)5) 2 (F) 4 (F) 6.3 (F) Fuse inserts 11/4“ x 1/4“ without indicator acc. to BS 88 (M) = mittelträge (F) = fast 33 kA Breaking capacity 33 kA fast G G G G G G G G 25/0.25A/M 25/0.50A/M 25/0.80A/M 25/1.00A/M 25/10.0A/M 25/2.00A/F 25/4.00A/F 25/6.30A/F 0546900000 0510300000 0646400000 0265800000 0193100000 0192700000 0192800000 0192900000 10 10 10 10 10 10 10 10 E 0.5 A 0.5 E 1 A 1 440 E 2 A 2 E 3 A 3 E 5 A 5 E 7 A 7 E 10 A 10 D fuse inserts E 16 with indicator acc. to DIN 49360 (diazed) GZ GZ GZ GZ GZ GZ GZ 0533800000 0525500000 0294500000 0295700000 0294600000 0295800000 0293900000 10 10 10 10 10 10 10 5 x 20 Breaking capacity 1500 A (at 250 V, 50 Hz, cos : 0.7) 250 SAKS 32) SAKS 6 0.5A/F 1.0A/F 2.0A 3.0A 5.0A 7.0A 10.0A SAKS 2 E 10 A 10 E 16/10A RT 500 E 16 A 16 E 16/16A GR E 20 A 20 E 16/20A BL E 25 A 25 E 16/25A GE D fuse inserts E 14 Size D 01 and E 18 size D 02 with indicator acc. to DIN 49522 (neozed)3) 0208500000 0208600000 0208700000 0208800000 25 25 25 25 SAKS 44) E E E E E E E E E E 0137400000 0137500000 0328300000 0328400000 0328500000 0361300000 0361400000 0361500000 0361600000 0361700000 10 10 10 10 10 10 10 10 10 10 SAKS 5 14/2 14/4 14/6 14/10 14/16 18/20 18/25 18/35 18/50 18/63 Note: 400 400 2 E 14/2A RS 4 E 14/4A BR 6 E 14/6A GN 10 E 14/10A RT 16 E 14/16A GR 20 E 18/20A BL 25 E 18/25A GE 35 E 18/35A SW 50 E 18/50A WS 63 E 18/63A KU (F) = fast (M) = miedium-delayed action SAK-series G fuse inserts 5 x 25 with indicator acc. to DIN 415761) SAKS 1 SAKS 7 WSI 6 1) The SIBA company also supplies 5 x 25 G fuse inserts with indicators in a shipbuilding model for 450 V AC. 5 x 30 (500 V AC) fuse inserts for SAKS 3 are available from the WICKMANN company 3) The LINDNER company also supplies neozed fuse cartridges in an additional shipbuilding mode for 440 V AC. 4) Fuse cartridges with the dimensions 1"x 1/4" c 25.4x6.35 mm and 13/32"x11/2" c 10.3x38.1 mm ar not included in product line. 5) Only for SAKS 1 and SAKS 7. 2) Gauge rings For terminal type SAKS 4 and 4/35 Gauge ring type P 14/2 P 14/4 P 14/6 P 14/1 Amp. 2 4 6 10 Colour Pink Brown Green Red Type P 14/2D01 RS P 14/4D01 BR P 14/6D01 GN P 14/10D01 RT Cat. No. 0138000000 0138100000 0328600000 0328700000 Qty. 50 50 50 50 SAKS 5 and 5/35 P P P P 18/20 18/25 18/35 18/50 20 25 35 50 Blue Yellow Black White P P P P 0361800000 0361900000 0362000000 0362100000 50 50 50 50 SAKS 2 and 2/35 P 16/10 P 16/16 P 16/20 10 16 20 Red Grey Blue P 16/10 RT P 16/16 GR P 16/20 BL 0208900000 0209000000 0209100000 100 100 100 18/20D02 18/25D02 18/35D02 18/50D02 BL GE SW WS 145 Disconnect test terminals SAKR SAKR/35 SAKR-D DKT 4 DKT 4/35 SAKR-D/35 DKT 4 V DKT 4 V/35 DLS 2 Y W Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 With/without plastic insulating collar mm2 Plug gauge according to 60 947-7-1 Size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data With 2 StB5) With 2 StB5) With 2 StB5) With 2 StB5) End plate (thickness mm) UL CSA Type KrG PA Without diode PA With diode PA Blue PA Orange PA KrG PA without diode PA Blue KrG PA Blue PA Y W Y W Y W ar# 6.5/42/40.5/54.5 (opened) 6.5/46/38/52 8 mm/M 3/3.5 x 0.6 6.5/42/40.5/57 (with DLS 2) 6.5/46/38/54.5 8 mm/M 3/3.5 x 0.6 ar# 6/65/56.5/70 (opened) 6/65/56.5/70 9 mm/M 3/3.5 x 0.6 6/65/56.5/70 (opened) 6/65/56.5/70 9 mm/M 3/3.5 x 0.6 400 V6)/10 A/4 mm2 6 kV/3 400 V/10 A/4 mm2 6 kV/3 400V/10 A/4 mm2 6 kV/3 400 V/10 A/4 mm2 6 kV/3 0.5…1.0/0.5 StB 2/1 0.5…1.0/0.5 StB 2/1 0.5…1.0/0.5 StB 2/1 0.5…1.0/0.5 StB 2/1 0.5…4 1.5…4 0.5…4 0.5…4 1.5…4 0.5…4 0.5…4 1.5…4 0.5…4 0.5…4 1.5…4 0.5…4 0.5…4 A3 (QB 2…25) 10 0.5…4 A3 (QB 2…25) 10 0.5…4 A3 (QB 2…4) 10 0.5…4 A3 (QB 2…4) 10 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG Y Qty. W Qty. 300 V/10 A/26…12 AWG 300 V/10 A/22…12 AWG Y Qty. W Qty. 300 V/10 A/22…12 AWG 300 V/10 A/26…12 AWG Y Qty. W Qty. 300 V/10 A/22…12 AWG 300 V/10 A/26…12 AWG Y Qty. W Qty. 04129600001)100 02999600001)50 0687360000 50 0687460000 50 0412120000100 0412160000100 0172160000100 04130600002)50 01857600002)50 02636600003)50 02995600003)50 0412180000100 0172180000100 1461960000100 0412220000100 0412260000100 0183360000100 05464600001) 100 0327860000 50 0327960000 50 1304860000 50 1304960000 50 04131600002) 50 0412280000100 0183380000100 Type AP (1.5) AP (1.5) AP (1.5) Cat. No. Qty. 0211320000 20 0211360000 20 0211380000 20 Type Cat. No. AP (1.5) Qty. 0211360000 20 Type AP (1.5) Cat. No. Qty. 0687560000 20 Type AP (1.5) Cat. No. Qty. 0687560000 20 Partition (thickness mm) Cross-connection QB 4 2-pole 3-pole 4-pole 25-pole TW HP (1.0) 0297100000 20 TW HP (1.0) 0297100000 20 TW HP (2.0) 0607000000 20 TW HP (2.0) 0607000000 20 QB 24) 0482700000 100 QB 34) 0482800000 50 QB 44) 0482900000 50 QB 25 blank4) 0134000000 20 QB 24) QB 34) QB 44) QB 25blank4) 0482700000100 0482800000 50 0482900000 50 0134000000 20 QB 24) QB 34) QB 44) 0482700000 100 0482800000 50 0482900000 50 QB 24) QB 34) QB 44) 0482700000 100 0482800000 50 0482900000 50 PS 2.3 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 DEK 6 see “Accessories” DEK 6 see “Accessories” Contact sleeve (spare) Test plug Diode plug (spare) without diode with diode 1N4007 with diode 1N4007 with jumper Marking tags 0180400000 20 DLS DLS DLS DLS DEK Print Standard DEK 6.5 see “Accessories” 2 0321060000 50 2 ) 0630160000 50 2 ( 0547760000 50 2 0547660000 25 DEK 6.5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 1) 2) without DLS with DLS empty 146 3) with DLS 1N4007 4) When using QB the rated cross-current reduces to max. 2.5 mm2 5) 6) With DKT 4 only on upper terminal level As disconnect test terminal rated voltage 250 V Disconnect test terminals ASK 1 ASK 1/35 Y W ar# 8/58/49 8/58/44 9 mm/M 3/3.5 x 0.6 500 V/19 A/4 mm2 6 kV/3 0.5…1.0 2 SAK-series 0.5…4 1.5…4 0.5…4 0.5…4 A3 (QB 2…4) 10 300 V/15 A/12 max. AWG 300 V/6.3 A/26…12 AWG Y + W Qty. 0456360000 100 0105260000 100 Type AP (1.5) Cat. No. Qty. 0380360000 20 TW HP (2.0) 0607000000 20 QB 24) 0461100000 100 QB 34) 0461200000 50 QB 44) 0461300000 50 multipole interruptable with group marking carrier SchS 2; 2-pole (Cat. No. 1359500000) 1000 mm (Cat. No. 0337400000) K sleeve 0553300000 100 DEK 5 FW see “Accessories” 147 Feed-through terminals with tab connection AST 1 AST1/35 AST 3 AST 3/35 AST 4 AST 4/35 AST 5 AST 5/35 6.3 2.8 6.3 2.8 6.3 2.8 6.3 2.8 Y W Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/-current Rated cross-section for clamping yokes Rated cross-section tab 6.3/2.8 mm Rated Voltage VDE 0110/1.89/pollution severty Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version Slotted KrG Slotted blue KrG Slotted PA Unslotted KrG Unslotted blue KrG Unslotted PA End plate/partition/small partition (thickness mm) AP TW TSCH 1 KrG Blue KrG PA PA HP HP Only for PA Cross-connection Q4 2-pole 3-pole 4-pole 10-pole 25-pole Y W Y W Y W a r # u DNV 6.5/58/53.5 6.5/58/46 a r # DNV 6.5/40/47.5 6.5/44/40 ar# 6.5/40/47.5 6.5/44/40 9 mm/M 2.5/3.5 x 0.6 a r # DNV 6.5/58/53.5 6.5/58/46 12 mm/M 3/3.5 x 0.6 500 V1)/2.5/1.0 mm2 6 kV/3 500 V1)/2.5/1.0 mm2 6 kV/3 500 V1)/2.5 mm2 2.5/1.0 mm2 6 kV/3 500 V1)/4 mm2 2.5/1.0 mm2 6 kV/3 0.4…0.7 1 0.5…1.0 2 0.5…4 1.5…2.5 0.5…2.5 0.5…2.5 A3 0.5…6 1.5…4 0.5…4 0.5…4 A4 (QL 2…10) 20 (QL 2…10) 20 (QL 2…10) 20 (QL 2…10) 20 300 V/13 A/– 300 V/16 A/– Y Qty. W 0478220000 50 300 V/13 A/– 300 V/16 A/– Y Qty. W 0442420000 100 0442470000 100 300 V/13 A/22…12 AWG 300 V/16 A/24…12 AWG Y Qty. W Qty. 0439120000 100 300 V/13 A/22…12 AWG 300 V/16 A/24…12 AWG Y Qty. W Qty. 0479220000 50 0460460000 100 0479260000 50 0664960000 50 Qty. 04782600002)50 06996600002)50 Qty. 04603600002) 100 0266320000 50 0298020000 100 02663600002)50 06648600002)50 02367600002)100 04793600002)10 Type AP (3.0) Cat. No. Qty. 0266420000 20 Type AP (3.0) Cat. No. Qty. 0298120000 20 Type AP (3.0) Cat. No. Qty. 0298120000 20 Type AP (3.0) Cat. No. Qty. 0266420000 20 AP (1.5) 0266460000 20 AP (1.5) TW (1.5) TW (1.0) 0460560000 20 0130160000 20 0297100000 20 0266460000 20 0474700000 20 0607000000 20 0319160000 100 0460560000 20 0130160000 20 0297100000 20 AP (1.5) TW (0.5) TW (2.0) TSch 1 AP (1.5) TW (1.5) TW (1.0) TSch 1 0319160000 100 TSch 1 0319160000 100 TW (1.0) TW (2.0) TSch 1 0474700000 20 0607000000 20 0319160000 100 Q Q Q Q 0336700000 0336800000 0336900000 0368800000 Q Q Q Q 0336700000 0336800000 0336900000 0368800000 Q Q Q Q 0336700000 0336800000 0336900000 0368800000 Q Q Q Q 0336700000 0336800000 0336900000 0368800000 2 3 4 10 50 50 50 20 2 3 4 10 0321220000 100 0321270000 100 50 50 50 20 0334520000 50 0479460000 100 2 3 4 10 50 50 50 20 0334560000 50 0699760000 50 2 3 4 10 50 50 50 20 Plug adapter Clips into PA version of AST 3 and AST 4 only 2-pole 3-pole 4-pole 5-pole 8-pole STA STA STA STA STA 2.5/2 2.5/3 2.5/4 2.5/5 2.5/8 0165860000 100 0165960000 50 0190360000 50 0166060000 50 0166160000 50 STA STA STA STA STA 2.5/2 2.5/3 2.5/4 2.5/5 2.5/8 0165860000 100 0165960000 50 0190360000 50 0166060000 50 0166160000 50 Test plug/socket Plug-test socket without using QL for TS 32 PS StB StB 14 0168600000 50 StB 14 0168600000 50 StB 14 0168600000 50 StB 14 0168600000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 IH 2.8 IH 6.3 0386060000 100 0386260000 100 IH 2.8 IH 6.3 0386060000 100 0386260000 100 IH 2.8 IH 6.3 0386060000 100 0386260000 100 IH 2.8 IH 6.3 0386060000 100 0386260000 100 DEK 6.5 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6.5 see “Accessories” Insulation sleeve Marking tags DEK Print Standard Mounting rails, end brackets, further marking material see “Accessories” 1) 2) 148 with insulation sleeve shock proof with ADP 4 cover profiles ADP4 (see section “Accessories”) Feed-through terminals with tab connection SAK 4 S SAK 4 S/35 SAK 4 SS SAK 4 SS/35 SAKR F SAKR F/35 6.3 2.8 6.3 2.8 2.8 Y W Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version Slotted KrG Slotted blue KrG Slotted PA Unslotted KrG End plate/partition/small partition (thickness mm) AP TW TSch 1 KrG Blue KrG PA PA HP T Cross-connection QL BS M 3 x 4.5 QB 4 2-pole 3-pole 4-pole 10-pole 25-pole BS M 3 x 24 ar#u 6.5/40/51.5 6.5/40/49.5 12 mm/M 3/3.5 x 0.6 ar#u 6.5/40/51.5 6.5/40/49.5 ar# 6.5/42/40.5/54.5 (opened) 6.5/42/40.5/32.5 8 mm/M 3/3.5 x 0.6 500 V1)/16 A 4 mm2 2.5/1.0 mm2 6 kV/3 500 V1)/16 A 250 V1)/10 A 4 mm2 -/1.0 mm2 6 kV/3 - 2.5/1.0 mm2 6 kV/3 0.5…1.0 2 0.5…1.0 1 0.33…6 1.5…4 0.5…4 0.5…4 A4 0.5…4 1.5…4 0.5…4 0.5…2.5 A3 SAK-series Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/-current Rated cross-section for clamping yokes Rated cross-section tab 6.3/2.8 mm Rated Voltage VDE 0110/1.89/pollution severty Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2 pole A Continuous current rating of cross-connection multipole A Y W Y W (QL 2…10) 36 A at 6 mm2 (QL 2…10) 36 A at 6 mm2 (QB 2…25) 10 300 V/13 A/26…12 AWG 300 V/13 A/26…12 AWG Y Qty. W Qty. 0401220000 100 300 V/13 A/18…14 AWG 300 V/13 A/18…14 AWG Y Qty. W Qty. 0479620000 10 300 V/10 A/22…12 AWG 300 V/10 A/26…12 AWG Y Qty. W Qty. 0401260000100 0630360000100 0479660000100 0630460000100 06636600001006382870000100 0352920000 10 with 1 StB 6 Type AP (1.5) Cat. No. Qty. 0117920000 20 AP (1.5) AP (1.5) TW (1.0) QL QL QL QL 2 3 4 10 0117960000 20 0130160000 20 0297100000 20 Type AP (1.5) AP (1.5) AP (1.5) TW (1.5) TW (1.0) Cat. No. Qty. 0117920000 20 0117970000 20 0117960000 20 0130160000 20 0297100000 20 0130600000 100 0130700000 100 0130800000 50 0338200000 20 QL QL QL QL 0130600000 100 0130700000 100 0130800000 50 0338200000 20 2 3 4 10 Type Cat. No. Qty. AP (1.5) 0211360000 20 TW (1.0) 0297100000 20 QB 2* QB 3* QB 4* 0482700000 100 0482800000 50 0482900000 50 QB 25 blank* 0134000000 20 BS M 3x4.5 1593210000 100 BS M 3x4.5 1593210000 100 Test plug/socket PS PS 2.3 0180400000 20 Insulation sleeve Marking tags DEK Print Standard IH 2.8 IH 6.3 0386060000 100 0386260000 100 IH 2.8 IH 6.3 0386060000 100 0386260000 100 IH 2.8 0386060000 200 DEK 6.5 see “Accessories” DEK 6.5 see “Accessories” DEK 6.5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 1) With insulation sleeve *The conductor cross-section for the screw connection is reduced to 2.5 mm2 when QB is used 149 Feed-through terminals with tab connection DK 4 SS/35 Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/-current Rated cross-section for clamping yokes Rated cross-section tab 6.3/2.8 mm Rated Voltage VDE 0110/1.89/pollution severty Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 With/without plastic insulation collar Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2 pole A Continuous current rating of cross-connection multipole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Version PA End plate (thickness mm) PA DK 4 SS/35 a r # LR u only 2.8 a r # LR u 6/54/60.5 6/54/60.5 400 V1)/2 x 16 A 400 V1)/2x10 - - 2.5/1.0 mm2 8 kV/3 1.0 mm2 4 kV/3 DK 4 S DK 4 S/35 DK 4 S only 2.8 DK 4 S/35 only 2.8 Y Y ar#u 6/54/59.5 6/54/60.5 9 mm/M 3/3.5 x 0.6 ar# 6/54/59.5 6/54/60.5 9 mm/M 3/3.5 x 0.6 400 V1)/2 x 10 4 mm2 1.0 mm2 6 kV/3 400 V1)/2 x 10 4 mm2 1.0 mm2 6 kV/3 0.5…1.0 2 0.5…1.0 2 0.5…4 1.5…4 0.5…4 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 A3 A3 (QL 2…10) 20 (QL 2…10) 20 (QL 2…10) 20 (QL 2…10) 20 300 V/10 A/22…12 AWG 300 V/10 A/22…12 AWG W Cat. No. Qty. 0217160000 100 300 V/10 A/22…12 AWG 300 V/10 A/22…12 AWG W Cat. No. Qty. 0297060000 100 300 V/10 A/22…12 AWG 300 V/10 A/22…12 AWG Y Qty. W Qty. 300 V/10 A/22…12 AWG 300 V/10 A/22…12 AWG Y Qty. W Qty. 0631260000100 0686660000100 0631160000 100 0686560000 100 Type AP (1.5) Type AP (1.5) Type AP (1.5) Type AP (1.5) Cat. No. Qty. 0631360000 20 Cat. No. Qty. 0631360000 20 Cat. No. 0631360000 Qty. 20 Cat. No. Qty. 0631360000 20 Partition for TS 32 HP TW HP (2.0) 0607000000 20 TW HP (2.0) 0607000000 20 Small partition TSch 6 Cross-connection Q3 2-pole 3-pole 4-pole 10-pole TSch 6 0190260000 100 TSch 6 0190260000 100 TSch 6 0190260000 100 TSch 6 0190260000 100 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 Test plug/socket Plug test socket without using QL Plug test socket for use with QL StB PS StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 IH 2.8 IH 6.3 0386060000 100 0386260000 100 IH 2.8 0386060000 100 IH 2.8 IH 6.3 0386060000 100 0386260000100 PS 2.3 IH 2.8 0180400000 20 0386060000 100 DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” Insulation sleeve Marking tags DEK Print Standard Mounting rails, end brackets, further marking material see “Accessories” 1) With insulation sleeve 150 Feed-through terminals for wrap termination SAK 2.5 T SAK 2.5 T SAK 2.5 T Pin 1 x 1 Pin 0.8 x 1.6 Pin 0.8 x 2.4 Y Dimensions/approvals Width/length/height (mm) with TS 32 Y Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to IEC 60 947-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2-pole A Continuous current rating of cross-connection multipole A Rated data according to UL/CSA Voltage/current/conductor size UL Voltage/current/conductor size CSA Ordering data Pin Version Right KrG Horizontal assembly Vertical assembly Horizontal right Vertical left Vertical right 2x vertical Right r 6/36.5/47.5/67 12 mm/M 2.5/3.5 x 0.6 r 6/36.5/47.5/62 12 mm/M 2.5/3.5 x 0.6 r 6/36.5/47.5/69 12 mm/M 2.5/3.5 x 0.6 250 V/8 A/2.5 mm2 4 kV/3 250 V/10 A/2.5 mm2 4 kV/3 250 V/10 A/2.5 mm2 4 kV/3 0.4…0.7 1 0.4…0.7 1 0.4…0.7 1 0.5…6 0.5…2.5 0.5…4 0.5…2.5 A3 0.5…6 0.5…2.5 0.5…4 0.5…2.5 A3 0.5…6 0.5…2.5 0.5…4 0.5…2.5 A3 (Q 2…10) 24 (Q 2…10) 24 (Q 2…10) 24 300 V/10 A/22…12 AWG Y Cat. No. Qty. 0108520000 100 300 V/10 A/22…12 AWG Y Cat. No. Qty. 300 V/10 A/22…12 AWG Y Cat. No. Qty. 0485920000 100 0478820000 100 0371020000 100 KrG KrG KrG KrG 0485020000 100 PA End plate (thickness mm) KrG PA Y Y SAK-series DIN 41 611, Part 2 and for spring-clip termination DIN 41 611, Part 4 01085600001)100 Type AP (1.5) Cat. No. Qty. 0279520000 20 Type AP (1.5) Cat. No. Qty. 0279520000 20 Type AP (1.5) Cat. No. Qty. 0279520000 20 AP (1.5) 0279560000 20 AP (1.5) 0279560000 20 AP (1.5) 0279560000 20 TW (2.5) 0302820000 20 TW (2.5) 0302820000 20 TW (2.5) 0302820000 20 TW (1.5) TW (0.5) TW (2.0) 0302860000 20 0197100000 20 0607000000 20 TW (1.5) TW (0.5) TW (2.0) 0302860000 20 0197100000 20 0607000000 20 TW (1.5) TW (0.5) TW (2.0) 0302860000 20 0197100000 20 0607000000 20 TSch 1 0319160000 100 TSch 1 0319160000 100 TSch 1 0319160000 100 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 Partition (thickness mm) KrG PA HP HP Small partition Cross-connection 2-pole 3-pole 4-pole 10-pole 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 2** 3** 4** 10** 50 50 50 20 Test plug/socket Plug-test socket without using QL PS StB Marking tags DEK Print Standard StB8.5(ø2.3) 0280600000 50 StB 8.5 (ø 2.3) 0280600000 50 StB8.5(ø2.3) 0280600000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 1) Shock-proof with ADP4 cover profile (see section “Accessories”) ** Not for Type 2 x vertical“ 151 Feed-through terminals Disconnect terminals for wrap connection acc. to DIN 41 611, Part 2 and for spring-clip connection acc. to DIN 41 611, Part 4 DK 4 T DK 4 T DK 4 T SAKRT Pin 1 x 1 Pin 0.8 x 1.6 Pin 0.8 x 2.4 Pin 1 x 1/0.8 x 2.4 and 0.8 x 1.6 Y Y Dimensions Width/length/height (mm) with TS 32 Y Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U Stranded H07V-R Flexible H07V-K Flexible H07V-K and ferrule according to DIN 46 228/1 With/without plastic insulating collar Plug gauge according to IEC 60 947-1 Continuous current of terminal block for conductor size Continuous current rating of cross-connection 2-pole Continuous current rating of cross-connection multipole Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data Pin Right Links Horizontal right Horizontal assembly Vertical assembly Vertical right Vertical right Vertical Vertical left Y Y 6/50/58.5/75.5 9 mm/M 3/3.5 x 0.6 6/50/60.5/77.5 9 mm/M 3/3.5 x 0.6 6/50/67.5/84.5 9 mm/M 3/3.5 x 0.6 6/42/40.5/54.5 8 mm/M 3/3.5 x 0.6 250 V/8 A/4 mm2 4 kV/3 250 V/10 A/4 mm2 4 kV/3 250 V/10 A/4 mm2 4 kV/3 250 V/6/8 A/4 mm2 4 kV/3 0.5…1.0 1 0.5…1.0 1 0.5…1.0 1 0.5…1.0 2 mm2 mm2 mm2 0.5…4 1.5…4 0.5…4 0.5…4 1.5…4 0.5…4 0.5…4 1.5…4 0.5…4 0.5…4 1.5…4 0.5…4 mm2 Size 0.5…4 A3 0.5…4 A3 0.5…4 A3 0.5…4 A3 (Q 2…10) 32 (Q 2…10) 32 (Q 2…10) 32 (QB 2…10) 10 – – Y – – Y – – Y – – Y Cat. No. 1x1 0587460000 100 0.8 x 2.4 0545060000 100 0.8 x 1.6 0469360000 100 Nm A A UL CSA Type PA PA PA Cat. No. Qty. 0536560000 50 Cat. No. Qty. Cat. No. Qty. 03704600001) 50 03703600001) PA Blue PA PA PA 05277600001) 50 13984600001) 50 DK 4 QT bridgeable on both levels Right PA End plate/partition (thickness mm) PA Blue PA Small partition TSch 4 Cross-connection/covers Q3 QB 4 2-pole 3-pole 4-pole 10-pole Type Cat. No. Qty. AP (1.5) 0359260000 20 AP (DK4 QT) 1397160000 20 Type AP (1.5) Cat. No. Qty. 0359260000 20 Type AP (1.5) Cat. No. Qty. 0359260000 20 Type AP (1.5) Cat. No. Qty. 0211360000 20 AP (1.5) TW (2.0) 0359280000 20 0607000000 20 AP (1.5) TW (2.0) 0359280000 20 0607000000 20 TW (2.0) 0607000000 20 TW (2.0) 0607000000 20 TSch 4 0363360000 100 TSch 4 0363360000100 TSch 4 0363360000 100 Q2 Q3 Q4 Q 10 QB 2* QB 3* QB 4* 0336400000 50 0336500000 50 0336600000 50 0368600000 20 0482700000 100 0482800000 50 0482900000 50 Q2 Q3 Q4 Q 10 QB 2* QB 3* QB 4* 0336400000 50 0336500000 50 0336600000 50 0368600000 20 0482700000 100 0482800000 50 0482900000 50 Q2 Q3 Q4 Q 10 QB 2* QB 3* QB 4* 0336400000 50 0336500000 50 0336600000 50 0368600000 20 0482700000 100 0482800000 50 0482900000 50 25-pole QB 2* 0482700000 100 QB 3* 0482800000 50 QB 4* 0482900000 50 QB 25 blank* 0134000000 20 Test plug/socket Plug-test socket without using QL StB 8.5 (ø 2.3) 0215700000 50 StB8.5 (ø2.3) 0215700000 50 StB8.5(ø2.3) 0215700000 50 PS 2.3 PS 2.3 0180400000 20 PS 2.3 0180400000 20 dekafix 6 see “Accessories” dekafix 6 see “Accessories” StB PS FW/FS 0180400000 20 dekafix 6 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” * The conductor cross-section for the screw connection is reduced to 2.5 mm2 when QB is used. ** Only to be used with PA-version 152 Qty. 1) Shock-proof with ADP4 cover profile (see section “Accessories”) Feed-through terminals and disconnect test terminals with solder connection SAK 2.5/M.LS SAK 2.5 L SAK 2.5 L/35 With screen lug SAK 2.5 LL SAK 2.5 LL/35 SAKR L SAKR L/35 Disconnect terminal Y Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Type KrG Blue KrG KrS PA Blue PA KrG r# 6/60/46.5 KrG Blue KrG PA Blue PA PA HP HP Y r# 6/55/46.5 6/55/40 12 mm/M 2.5/3.5 x 0.6 r# 6/44.5/46.5 6/44.5/40 12 mm/M 2.5/3.5 x 0.6 ar# 6.5/50/40.5/54.5 (opened) 6.5/50/38/52 8 mm/M 3/3.5 x 0.6 250 V/20 A/2.5/1.5 mm2 4 kV/3 250 V/20 A/2.5/1.5 mm2 4 kV/3 250 V/20 A/1.5 mm2 4 kV/3 250 V/10 A/4/1.5 mm2 4 kV/3 0.4…0.7 1 0.4…0.7 1 0.5…1.0 2/1 0.5…6 0.5…2.5 0.5…4 0.5…2.5 A3 0.5…6 0.5…2.5 0.5…4 0.5…2.5 A3 0.5…4 0.5…4 0.5…4 0.5…4 A3 (Q 2…10) 24 (Q 2…10) 24 (Q 2…10) 24 300 V/10 A/22…12 AWG Y Cat. No. Qty. 0309120000 100 300 V/10 A/22…12 AWG Y Qty. W Qty. 0351420000 100 0351470000 100 300 V/10 A/26…12 AWG Y Qty. W Qty. 0323620000 100 0323670000 100 03514600002)100 04950600002)100 03236600002)10005672600002)100 (QB 2…25) 10 300 V/10 A/22…12 AWG 300 V/10 A/22…12 AWG Y Qty. 0412360000 100 0412380000 100 0544120000* 100 PA Blue PA End plate/partition (thickness mm) AP TW Y W SAK-series Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal block for conductor size Continuous current rating of cross-connection 2-pole A Continuous current rating of cross-connection multipole A Y W 0544160000*2)100 Type AP (1.5) AP (1.5) Cat. No. Qty. 0309220000 20 0309270000 20 0412460000* 100 0412480000* 100 Type AP (1.5) AP (1.5) AP (1.5) Cat. No. Qty. 0309220000 20 0309270000 20 0279560000 20 Type AP (1.5) AP (1.5) AP (1.5) Cat. No. Qty. 0309220000 20 0309270000 20 0279560000 20 TW (1.5) TW (1.0) TW (2.0) 0302860000 20 0297100000 20 0607000000 20 TW (1.5) TW (1.0) TW (2.0) 0302860000 20 0297100000 20 0607000000 20 TW (1.5) TW (1.0) TW (2.0) 0302860000 20 0297100000 20 0607020000 20 TSch 1 0319160000 100 TSch 1 0319160000 100 TSch 1 0319160000 100 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 Q Q Q Q 0337000000 0337100000 0337200000 0368700000 Type Cat. No. Qty. AP (1.5) AP (1.5) 02113600001)20 0211380000 20 TW (2.0) 0607000000 20 QB 2** QB 3** QB 4** 0482700000 100 0482800000 50 0482900000 50 Small partition Cross-connection Q3 Q4 2-pole 3-pole 4-pole 10-pole 25-pole 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 QB 25 blank** 0134000000 20 Test plug/socket Plug-test socket without using QL Plug-test-socket for use with QL StB StB8.5(ø2.3) StB 29.5(ø4) PS 2.3 PS 4 PS 0280600000 0133400000 0180400000 0299600000 50 50 20 20 StB8.5(ø2.3) StB 29.5(ø4) PS 2.3 PS 4 0280600000 0133400000 0180400000 0299600000 50 50 20 20 PS 2.3 0180400000 20 Cover Marking tags DEK Print Standard AD 4 0303400000 50 BSK M3 x 22 0128900000 100 AD 4 0303400000 50 BSK M 3x 22 0128900000 100 AD 4 0303400000 50 BSK M 3x 22 0128900000 100 DEK 6 DEK 6 DEK 6 see “Accessories” see “Accessories” see “Accessories” DEK 6.5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” * Soldering lug on left-hand side ** The conductor cross-section for the screw connection is reduced to 2.5 mm2 when QB is used. 1) 2) For TS 32 and TS 35 Contact-proof cross-connection with ADP 4 cover profile (see “Accessories”) 153 Disconnect test terminals with solder connections SAKR L SAKR LL With 2 StB 6 With 2 StB 6 Y Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Type KrG Blue KrG KrS PA Blue PA KrG KrS PA Blue PA End plate/partition (thickness mm) AP TW W 6.5/50/40.5/54.5 (opened) r# 6.5/58/40.5/54.5 (opened) 8 mm/M 3/3.5 x 0.6 6.5/58/40.5/54.5 (opened) –/–/3.5 x 0.6 250 V/10 A/1.5 mm2 4 kV/3 250 V/10 A/4/1.5 mm2 4 kV/3 250 V/10 A/1.5 mm2 4 kV/3 0.5…1.0 1 0.5…4 1.5…4 0.5…4 0.5…4 A3 (QB 2…25) 10 Y Qty. W Qty. 0518160000*100 0183560000 100 300 V/10 A/22…12 AWG Y Qty. Y 0464460000 100 Qty. W Qty. 0294260000 100 0572660000 100 Qty. Type AP (1.5) Cat. No. Qty. 0211320000 20 Type AP (1.5) Cat. No. Qty. 0211320000 20 AP (1.5) AP (1.5) 0211360000 20 0211380000 20 AP (1.5) AP (1.5) 0211360000 20 0211380000 20 AP (1.5) AP (1.5) 0211360000 20 0211380000 20 TW (0.5) TW (2.0) 0474700000 20 0607000000 20 TW (0.5) TW (2.0) 0474700000 20 0607000000 20 TW (0.5) TW (2.0) 0474700000 20 0607000000 20 QB 2** QB 3** QB 4** 0482700000 100 0482800000 50 0482900000 50 PS 2.3 0180400000 20 DEK 6.5 see “Accessories” Type KrG Blue KrG PA Blue PA PA HP HP Y Y W Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46228/1 With/without plastic insulating collar mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal block for conductor size Continuous current rating of cross-connection 2 pole A Continuous current rating of cross-connection multipole A SAKR LL Cat. No. Small partition Cross-connection QB 3 QB 4 2-pole 3-pole 4-pole 10-pole 25-pole QB 25 blank** 0134000000 20 Test plug/socket PS Marking tags DEK Print Standard PS 2.3 0180400000 20 DEK 6.5 see “Accessories” DEK 6.5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” * Soldering lug on left-hand side ** The conductor cross-section for the screw connection is reduced to 2.5 mm2 when QB is used. 154 Disconnect test terminals with solder connections TAL TAL SAKK 4 2 solder connections 4 solder connections Ceramic feed-through terminals for use in high temperature ranges up to max. 210°C Dimensions/approvals Width/length/height (mm) with TS 32 Y Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46 228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal block for conductor size Continuous current rating of cross-connection 2 pole A Continuous current rating of cross-connection multipole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Type KrG Blue KrG KrS PA Blue PA KrG KrS PA Blue PA Ceramic End plate/partition (thickness mm) AP TW 4/48/36/50 (opened) 4/54/36/50 (opened) 63 V/10 A/1.5 mm2 1.5 kV/3 Y Cat. No. 63 V/10 A/1.5 mm2 1.5 kV/3 Qty. Y 0212060000 100 Type KrG Blue KrG PA Blue PA PA Y AP (1.5) Cat. No. Qty. 0212260000 20 Cat. No. Qty. 8/40/53 11.5/40/53 12 mm/M3/3.5 x 0.6 IEC 60 947-7-1 800 V/32 A/4 mm2 12 mm/M 4/5.5 x 1.0 IEC 60 947-7-1 800 V/57 A/10 mm2 0.5…1 1.2…2 0.5...6 mm2 0.5...4 mm2 2.5...16 mm2 2.5...10 mm2 A4 35 A/6 mm2 36 36 B6 63 A/16 mm2 47 36 Y Cat. No. Qty. Y SAK-series Y SAKK 10 Cat. No. Qty. 0304960000 100 Type AP (1.5) Cat. No. Qty. SAKK 4 1598080000 50 Type Cat. No. Qty. AP/SAKK4/10 9502630000 10 SAKK 10 1598090000 50 Type Cat. No. Qty. AP/SAKK4/10 9502630000 10 Type QL 2 QL 3 QL 4 QL 10 VH 13.5 BS (M 3 X 20) Cat. No. Qty. 9509420000 100 9509430000 100 9509440000 50 9509450000 20 0248500000 100 0303000000 100 Type QL 2 QL 3 QL 4 QL 10 VH 12.5 BS (M3 X 20) Cat. No. Qty. 9509470000 100 9509480000 50 9509490000 50 9509500000 20 9509510000 50 0303000000 100 SST MEW 1/32 EK 2 0152700000 0445600000 0323100000 SST MEW 1/32 EK 2 0152700000 0445600000 0323100000 0212260000 20 Small partition Cross-connection Q3 QB 4 2-pole 3-pole 4-pole 10-pole 25-pole Additional accessories Marking tags DEK Print Standard On demand On demand Mounting rails, end brackets, further marking material see “Accessories” 155 Feed-through terminals for initiators and actuators DLI 2.5 Dimensions/approvals Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule according to DIN 46228/1 mm2 Plug gauge according to 60 947-7-1 Size Continuous current of terminal for conductor size Continuous current rating of cross-connection 2…5-pole A Continuous current rating of cross-connection 6…10-pole A Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA Standard with diode 1N4007 with LED red (5…30 V) with LED green (5…30 V) with LED and diode 1N4007 with LED and diode 1N4007 Block of 101) Block of 101) Fuse inserts End plate/Small partition AP-DLI AP-DLD Part-AP TSch 1 DLI 2.5 LD DLI 2.5 LD PNP DLD 2.5 NPN W W W ar# 6/65/49 7 mm/M 2.5/3.5 x 0.6 ar# 6/65/49 7 mm/M 2.5/3.5 x 0.6 ar# 6/65/49 7 mm/M 2.5/3.5 x 0.6 ar# 6/82/49 7 mm/M 2.5/3.5 x 0.6 250 V/20 A/2.5 mm2 4 kV/3 5–30 V-/20 A/2.5 mm2 0.8 kV/3 5–30 V-/20 A/2.5 mm2 0.8 kV/3 250 V/24 A/2.5 mm2 4 kV/3 0.4…0.6 1 0.4…0.6 1 0.4…0.6 1 0.4…0.6 1 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…10) 20 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…10) 20 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…10) 20 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG W Cat. No. Qty. 1313360000 100 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG W Cat. No. Qty. 1317060000 50 W Cat. No. Qty. W 1578510000 100 1578520000 100 Best.-Nr . W (Q 2…10) 20 Qty. 1578550000 100 1578560000 100 (with dekafix) 1579070000 1411360000 10 10 (LED red) 1578530000 (LED green) 1578540000 Type AP Cat. No. Qty. 1313260000 20 Type AP Cat. No. Qty. 1313260000 20 Type AP Cat. No. Qty. 1313260000 20 TSch 1 0319160000 100 TSch 1 0319160000 100 TSch 1 0319160000 100 (w/o) 10 10 Type Cat. No. Qty. AP 1317660000 20 AP (Part-AP)1381860000 20 TSch 1 0319160000 100 (thickness 1.5 mm) Test plug/plug socket StB 8.5 PS Cross-connection Q3 VQB Snap fit, external cross-connection VQB 1.5. For cross-connections for more than 20 terminals, replace VH with VH 4.2 (134580) without internal thread Group marking WT 4 Cover HP 4 Marking tags DEK Print Standard StB8.5*(ø2.3) 0215700000 50 PS 2.3 0180400000 20 Q Q Q Q Q 1312500000 1312600000 1312700000 1313100000 1399800000 50 50 50 20 20 2 3 4 10 20 Q Q Q Q Q 2 3 4 10 20 1312500000 1312600000 1312700000 1313100000 1399800000 50 50 50 20 20 Q Q Q Q Q 2 3 4 10 20 1312500000 1312600000 1312700000 1313100000 1399800000 50 20 Q Q Q Q Q 50 50 50 20 20 2 3 4 10 20 1312500000 1312600000 1312700000 1313100000 1399800000 QL 2 0297200000 100 VH 4.2 1345800000 100 VQB1.5/50BL 1633280000 5 VQB1.5/50RT 1633290000 5 VQB1.5/50SW1635120000 5 QL 2 VH 4.2 0297200000 100 1345800000 100 VQB1.5/50 BL1633280000 5 VQB1.5/50RT 1633290000 5 VQB1.5/50 SW 1635120000 5 QL 2 VH 4.2 0297200000 100 1345800000 100 VQB1.5/50 BL1633280000 5 VQB1.5/50RT 1633290000 5 VQB1.5/50 SW 1635120000 5 QL 2 VH 4.2 WT 4 SF 10 SG 10 1341060000 100 03324000001000 03325000001000 WT 4 SF 10 SG 10 1341060000 100 03324000001000 03325000001000 WT 4 SF 10 SG 10 1341060000 100 03324000001000 03325000001000 WT 4 SF 10 SG 10 1341060000 100 03324000001000 0332500000 1000 ADP HP 4 0485400000 0485860000 ADP HP 4 0485400000 0485860000 ADP HP 4 0485400000 0485860000 ADP HP 4 0485400000 0485860000 DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” 20 20 20 20 Mounting rails, end brackets, further marking material see “Accessories” 1) 156 50 50 50 20 20 StB8.5*(ø23 . ) 0215700000 PS 2.3 0180400000 DLI 2.5/35/10 = Block of 10 with built-in cross-connections * only in upper busbar 20 20 0297200000 100 1345800000 100 VQB1.5/50 BL1633280000 5 VQB1.5/50RT 1633290000 5 VQB1.5/50 SW 1635120000 5 20 20 Feed-through terminals for initiators and actuators DLA 2.5 DLA 2.5/D DLA 2.5/LD W W W DLA 2.5/LD/D DLD 2.5/PE W KDKS1 / PE W W A4 A4 A4 A4 A3 arq# 6/65/49 7 mm/M 2.5/3.5 x 0.6 arq# 6/65/49 7 mm/M 2.5/3.5 x 0.6 arq# 6/65/49 7 mm/M 2.5/3.5 x 0.6 arq# 6/65/49 7 mm/M 2.5/3.5 x 0.6 ar# 6/74.5/49 7 mm/M 2.5/3.5 x 0.6 a# 8/91/65 8 mm/M 32)/M 2.53)/3.5 x 0.6 250 V**/17.5 A/2.5 mm2 4 kV/3 250 V**/17.5 A/2.5 mm2 4 kV/3 5–30 V/17.5 A/2.5 mm2 0.8 kV/3 5–30 V/17.5 A/2.5 mm2 0.8 kV/3 250 V**/17.5 A/2.5 mm2 4 kV/3 500 V / 6 . 3 A / 4 mm2 6 kV/3 0.4…0.6 1 0.4…0.6 1 0.4…0.6 1 0.4…0.6 1 0.4…0.6 1 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…20) 20 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…20) 20 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…20) 20 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…20) 20 0.5…4 0.5…2.5 0.5…4 0.5…2.5 A3 20 A/2.5 mm2 (Q 2…20) 20 0.5…4 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG W Cat. No. Qty. 1565970000 100 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG W Cat. No. Qty. 300 V/10 A/26…12 AWG 5–30 V/10 A/26…12 AWG W Cat. No. Qty. 300 V/10 A/26…12 AWG 5–30 V/10 A/26…12 AWG W Cat. No. Qty. 300 V/10 A/26…12 AWG 300 V/10 A/26...12 AWG W Cat. No. Qty. 1595950000 100 -/-/22...12 AWG 0.5…1 2)/ 0 . 4…0.73) 2/1*** 1578400000 100 1578430000 100 1578440000 100 (w. dekafix) 1578380000 (w/o dekafix) 1578390000 (LED (LED (LED (LED 10 10 red) green) red) green) Cat. No. Qty. 1313260000 20 Type AP Cat. No. Qty. 1313260000 20 Type AP Cat. No. Qty. 1313260000 20 Type AP Cat. No. Qty. 1313260000 20 TSch 1 0319160000 100 TSch 1 0319160000 100 TSch 1 0319160000 100 TSch 1 0319160000 100 50 20 Q Q Q Q Q 50 50 50 20 20 2 3 4 10 20 1312500000 1312600000 1312700000 1313100000 1399800000 QL 2 VH 4.2 0297200000 100 1345800000 100 VQB1.5/50BL 1633280000 5 VQB1.5/50RT 1633290000 5 VQB1.5/50SW 1635120000 5 Q Q Q Q Q 2 3 4 10 20 1312500000 1312600000 1312700000 1313100000 1399800000 50 50 50 20 20 QL 2 VH 4.2 Q Q Q Q Q 2 3 4 10 20 1312500000 1312600000 1312700000 1313100000 1399800000 50 50 50 20 20 Q Q Q Q Q 2 3 4 10 20 1312500000 1312600000 1312700000 1313100000 1399800000 50 50 50 20 20 Type Cat. No. Qty. AP 1595960000 20 AP (Part-AP) 1595970000 TSch 1 0319160000 100 StB8.5*(ø2.3) 0215700000 PS 2.3 0180400000 50 20 Q Q Q Q Q 50 50 50 20 20 2 3 4 10 20 0297200000 100 1345800000 100 VQB1.5/50 BL 1633280000 5 VQB1.5/50 RT 1633290000 5 VQB1.5/50 SW 1635120000 5 QL 2 VH 4.2 0297200000 100 1345800000 100 VQB1.5/50 BL 1633280000 5 VQB1.5/50 RT 1633290000 5 VQB1.5/50 SW 1635120000 5 QL 2 VH 4.2 0297200000 100 1345800000 100 VQB1.5/50 BL 1633280000 5 VQB1.5/50 RT 1633290000 5 VQB1.5/50 SW 1635120000 5 QL 2 VH 4.2 1312500000 1312600000 1312700000 1313100000 1399800000 1341060000 100 0332400000 1000 0332500000 1000 WT 4 SF 10 SG 10 1341060000 100 0332400000 1000 0332500000 1000 WT 4 SF 10 SG 10 1341060000 100 0332400000 1000 0332500000 1000 WT 4 SF 10 SG 10 1341060000 100 0332400000 1000 0332500000 1000 WT 4 SF 10 SG 10 1341060000 100 0332400000 1000 0332500000 1000 ADP HP 4 0485400000 0485860000 ADP HP 4 0485400000 0485860000 ADP HP 4 0485400000 0485860000 ADP HP 4 0485400000 0485860000 ADP HP 4 0485400000 0485860000 DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” 20 20 20 20 20 20 5 x 20 without core indicator Type Cat. No. Qty. AP 9503330000 50 AP Wemid 9532470000 50 QB 2 QB 3 QB 4 0461100000 0461200000 0461300000 50 50 50 DEK 8 see “Accessories” 0297200000 100 1345800000 100 VQB1.5/50 BL 1633280000 5 VQB1.5/50 RT 1633290000 5 VQB1.5/50 SW 1635120000 5 WT 4 SF 10 SG 10 20 20 Cat. No. Qty. 9528110000 50 not combine with DLI / DLA Wemid 9532450000 50 W 1578470000 100 1578480000 100 1578490000 10 1578500000 10 Type AP StB8.5*(ø2.3) 0215700000 PS 2.3 0180400000 SAK-series 0.5…4 0.5…4 A 4 2)/ A 33) 20 20 ** If the cross-connection runs via the PE connection of the DLA, or if a pole is generally skipped, the rated voltage is reduced to 30 V~ 2) A4 clamping position = max 4 mm2 ... 3) A3 clamping position = max 2.5 mm2 ... ferrule with/without plastic insulating collar 157 Feed-through terminals for initiators and motors VLI 1.5 VLI 1.5PE W MAK 2.5 W W Dimensions/approvals Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade aq# 6/79/64 8 mm/M 2.5/3.5 x 0.6 aq# 6/69/63 8 mm/M 2.5/3.5 x 0.6 ar# 6/88/64 8 mm/M 2.5/3.5 x 0.6 Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section 250 V/17.5 A/1.5 mm2 250 V/17.5 A/1.5 mm2 4 kV/3 4 kV/3 500 V (L-L) / 250 V (L-PE) 24 A/2.5 mm2 6 kV/3 0.4…0.6** 1 0.4…0.6 1 0.4…0.6 1 0.5…4.0 0.5…2.5 0.5…4 0.5…2.5 0.5…2.5 A3 0.5…4.0 0.5…2.5 0.5…4 0.5…2.5 0.5…2.5 A3 0.5…4.0 0.5…2.5 1.5…4 0.5…2.5 0.5…2.5 A3 24 A/2.5 mm2 24 24 A/2.5 mm2 24 24 A/4 mm2 24 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG W Cat. No. Qty. 1633250000 50 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG W Cat. No. Qty. 1633310000 50 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG W Cat. No. Qty. 1615270000 50 1631650000 50 Type AP VLI1.5 Type Cat. No. Qty. APVLI1.5/PE 1633320000 20 Type Cat. No. Qty. AP MAK2.5 1615280000 20 TEAP2 MAK2.51633330000 20 Rated impulse voltage/pollution severity Further technical data Tightening torque range Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U Stranded H07V-R Flexible H07V-K Flexible H07V-K and ferrule DIN 46 228/1 Flexible H07V-K and ferrule with plastic insul. collar Plug gauge according to 60 947-7-1 Continuous current of terminal for conductor size Continuous current rating of cross-connection, multipole Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data Nm mm2 mm2 mm2 mm2 mm2 Size A UL CSA Version PA End plate/partition End plate Partial end plate for VLI1.5 – MAK2.5 combination Partial end plate for VLI1.5 – VLI1.5PE combination Partial end plate for VLI1.5PE – MAK2.5 combination Cross-connection VQB 50-pole, snap-fit, external cross-connection Cat. No. Qty. 1633260000 20 TEAP 2 MAK2.5 1633330000 20 TEAP VLI1.5 1633270000 20 VQB1.5/50BL* 1633280000 VQB1.5/50RT* 1633290000 VQB1.5/50SW*1635120000 5 5 5 TEAP VLI1.5 1633270000 20 TEAP1MAK2.5 1633340000 20 TEAP1 MAK2.51633340000 20 VQB1.5/50BL* 1633280000 5 VQB1.5/50RT* 1633290000 5 VQB1.5/50SW*1635120000 5 VQB1.5/50BL* 1633280000 VQB1.5/50RT* 1633290000 VQB1.5/50SW*1635120000 QB 25 SW* 0520000000 QB 25 RT* 0520060000 QB 25 BL* 0520080000 QB 25-pole external cross-connection 5 5 5 20 20 20 Group marking Tag carrier for S 10 tags Marking tags DEK Print Standard T5 SF 10 SG 10 0348500000 100 03324000001000 03325000001000 T5 SF 10 SG 10 0348500000 100 03324000001000 03325000001000 T5 SF 10 SG 10 0348500000 100 03324000001000 03325000001000 DEK 5 see “Accessories” DEK 5 see “Accessories” DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” * When using cross-connection bridges, the connected cross-section is reduced by one level ** 0.4…0.45 for lower connection level 158 Disconnect test terminal against induced high voltage PPT/35 SAKH 6 Y Dimensions/approvals Width/length/height (mm) with TS 35 x 7.5 W Insulation stripping length/clamping screw/screwdriver blade • Insulation between installation and control cable by pulling disconnect plugs. Rated data according to IEC 60 947-7-1 Rated voltage/current Rated impulse voltage/pollution severity • Grounding of control cable is possible on an appropriate location of the workplace. • Easy connection of electric isolation of counting, control and communication circuits. Clampable conductor Solid H07V-U Stranded H07V-R mm2 mm2 Ordering data Version EP EP 0.5...10 0.5...10* 0.5... 6 0.5... 6 W Cat. No. Qty. PPT/35 3835020000 10 incl. disconnect plug and displacement tool (if min. 10 items are ordered) W SAKH 6 Cat. No. Qty. 0126600000 50 AP/PPT (3) 3835120000 10 TST/PPT 10 AP 0131700000 20 Disconnect plug Displacement tool • Separation of control cables from local control circuits. Test plug/socket • Grounding of control cables and / or auxiliary control circuits. 1 kV ac / 1.5 kV dc / 47 A >15 kV (from terminal to terminal) End plate • Insulation of the control cables located in front of ground or installation lines with increased potential, which is required to prevent unintentional contact of service staff with live parts. • Application also includes test connections for auxiliary control circuits and / or local control circuits. 12 mm 15 kV ac (ESI 12-4)**/30 A Electricity Supply Industry Standard ESI 12-4 1973 The Electricity Supply Industry Standard ESI 12-4 1973 defines a detailed specification of control and protection equipment. The main functions of thiese installations are as follows: 15/138/79 12 mm PA 3835360000 PH/PPT 3835260000 10 The disconnect plug may only be removed with the displacement tool. PS (4) StB 17 0299600000 0147100000 20 50 TSK 35 0514300000 1 Insulated mounting rail PVC 35 x 1.5 mm Marking tags DEK • Bundled disconnection of all auxiliary control circuits from potential earth. Print Standard DEK 5 see “Accessories” DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” • A test voltage can be applied using the screening connection of the control cable, which is normally routed on the enclosure, with the help of an appropriate separation. This permits to check whether the screening line is correctly functioning. For this test, an insulated feed-through plate is required. ESI 12-4: "Terminating Equipment for Pilot Cables subject to Induced Transient Voltages exceeding 650 V rms". * Also two push-on tabs are possible ** mounted on an insulated mounting rail 159 SAK-series Measures to minimize risks of electric voltage peaks in control systems of power plants and transforming stations: Rail mounting TS 15 Feed-through terminals Protective conductor terminals Fuse terminals Disconnect test terminals AKZ 1.5 AKZ 1.5/10 AKZ 2.5 Max. technical data Dimensions/approvals Width/length/height (mm) 21.5 A / 2.5 mm2 ar# 5/25/25 26 A / 4 mm2 ar# 5/25.5/28 38.5 A / 6 mm2 ar# 6/27/30 38.5 A / 6 mm2 Insulation stripping length/clamping screw/screwdriver blade Rated data VDE 0611 Part 1/8.92/IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage / pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size 7 mm/M 2.5/3.0 x 0.5 7 mm/M 2.5/3.0 x 0.5 8 mm/M 3/3.5 x 0.6 9 mm/M 3/3.5 x 0.6 250 V/17.5 A/1.5 mm2 4 kV/3 250 V/24 A/2.5 mm2 4 kV/3 400 V/32 A/4 mm2 6 kV/3 500 V/32 A/4 mm2 6 kV/3 0.4…0.6 1 0.4…0.6 1 0.5…1.0 2 0.5…1.0 2 0.5…2.5 1.5 0.5…1.5 0.5…1.5 0.5…1.5 0.2…2.5 / A 1 0.5…4 1.5…2.5 0.5…4 0.5…2.5 0.5…2.5 0.13…4.0 / A 3 0.5…6 1.5…4 0.5…4 0.5…4 0.5…4 0.2…6.0 / A 3 0.5…6 1.5…4 0.5…4 0.5…4 0.5…4 0.2…6.0 / A 3 Continuous current rating of cross-connection 2-pole Continuous current rating of cross-connection multipole Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data 24 24 24 24 32 32 32 32 150 V/15 A/22…14 AWG 300 V/10 A/24…16 AWG U TS 15 Cat. No. Qty. 300 V/10 A/26…12 AWG 300 V/10 A/26…12 AWG U TS 15 Cat. No. Qty. 300V/27 A/22…12 AWG 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 0340460000 100 0340480000 100 (10pol./no mk.) 0358060000 10 (10pol./w.mk.) 0358160000 10 (with pin) (with pin) (without pin) AKZ 2.5 w. AP 300 V/27A/22…12 AWG 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 0294320000 100 0294360000 100 0294380000 100 (10pol./no mk.) 0359560000 10 (10pol./w.mk.) 0359660000 10 AKZ4Wemid 9537110000 100 U U with TS 15 U A A UL CSA Type KrG PA Blue PA PA PA End plate (thickness mm) Type KrG Wemid PA Blue PA AP (1.5) Cat. No. AKZ 4 AKZ 4/10 AKZ 4 Wemid Qty. 0340560000 50 Type AP (2.5) AP (2.5) U 0697160000 100 0697180000 100 0175960000 100 0385860000 50 Cat. No. AKZ 4 for test adapter AKZ 4/10 for test adapter Qty. 0697360000 50 0697380000 50 Type AP (1.5) AP (1.5) AP (1.5) AP (1.5) Cat. No. Qty. 0294420000 20 9537910000 20 0294460000 20 0294480000 20 TW (2.0) 0118900000 20 TW (0.5) ar# 60/27/30 for test adapter1538260000 100 w.mk./f.test ad.1489360000 10 ATA1,10-pole 1633240000 5 Type Cat. No. Qty. AP (1.5) 0294460000 20 0348260000 50 TW (0.5) 0348260000 50 TSch 4 0363360000 100 TSch 4 0363360000 100 Q2 Q3 Q4 0336400000 50 0336500000 50 0336600000 50 Q2 Q3 Q4 0336400000 50 0336500000 50 0336600000 50 Q 10 0368600000 20 Q 10 0368600000 20 Partition (thickness mm) KrG PA Blue PA TW (1.5) TW (1.5) 0318560000 20 0318580000 20 Small partition PA Cross-connection Q Q Q Q Q Q2 QB 4 Switchable cross-connection link 2 3 4 5 10 0368200000 0368300000 0368400000 0660300000 0368500000 50 50 50 20 20 Q Q Q Q Q 2 3 4 5 10 0368200000 0368300000 0368400000 0660300000 0368500000 50 50 50 20 20 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 Marking tags can be snapped on via cross-connection AD 4 0303400000 50 BSK M2.5x18 0303300000 100 ADP 41) 1378160000 10 AD 4 0303400000 50 BSK M 2.5x18 0303300000 100 ADP 41) 1378160000 10 VL BS VH Cover/Profiled material for covers for finger-safety* Test plug/socket StB PS Plug test socket can be used without QL K sleeve Marking tags DEK Print Standard StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 DEK 5 see “Accessories” DEK 5 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” * not for terminals made from PA 160 1) Length: 300 mm Rail mounting TS 15 AKE 2.5 AKE 4 U 38.5 A / 6 mm2 ar 60/32/34 AKE 4 MS SAKR Isolating blade terminal with 2 sockets or with 2 clamping screws U U ar 5/28/27 ASK 1 Fuse terminal U U ar 7/32/34 r 7/27.5/30 ar 8/58/34 6.5/42/45 9 mm/M 3/3.5 x 0.6 IEC 60 947-7-2 –/–/4 mm2 8 kV/3 9 mm/M 3/3.5 x 0.6 9 mm/M 3/3.5 x 0.6 8 mm/M 3/3.5 x 0.6 690 V/32 A/4 mm2 8 kV/3 7 mm/M 2.5/3.0 x 0.5 IEC 60 947-7-2 –/–/2.5 mm2 4 kV/3 –/–/4 mm2 500 V/6.3 A*/4 mm2 6 kV/3 400 V2)/10 A/4 mm2 6 kV/3 0.5…1.0 2 0.4…0.6 1 0.5…1.0 2 0.8…1.6 3 0.5…1.0 2 0.5…1.0 2 0.5…6 1.5…4 0.5…4 0.5…4 0.5…4 0.2…6.0 / A 3 0.5…4 1.5…2.5 0.5…4 0.5…2.5 0.5…2.5 0.13…4.0 / A 3 0.5…6 1.5…4 0.5…4 0.5…2.5 0.5…2.5 0.13…4.0 / A 3 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.5…4.0 / A 3 0.5…4 1.5…4 0.5…4 0.5…2.5 0.5…2.5 0.13…4.0 / A 3 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.13…4.0 / A 3 (QB 2…4) 10 (QB 2…4) 10 9 mm/M 3/3.5 x 0.6 20 20 U TS 15 Cat. No. Qty. –/–/26…12 AWG –/–/26…12 AWG U TS 15 Cat. No. 0489560000 100 Qty. –/–/22…12 AWG –/–/26…12 AWG U TS 15 Cat. No. 1303360000 100 (green/yellow) Qty. –/–/22…14 AWG U TS 15 Cat. No. 0380260000 100 (green/yellow) Qty. 0211200000 50 300 V/10 A/22…12 AWG 300 V/6.3 A/26…12 AWG U TS 15 Cat. No. Qty. 0376860000 100 5 x 20 without indicator (10pol./no mk.) 0366560000 10 U TS 15 with 2 StB Cat. No. SAK-series AK 4 AK 4/10 Qty. 0412860000 100 w. clamp.screw 0412760000 100 (10pol./w.mk.) 0469560000 10 Type Cat. No. Qty. Type Cat. No. Qty. Type Cat. No. Qty. Type BB 3 (8.0) 0366660000 50 combined AP + end brackets Cat. No. Qty. Type AP (1.5) Cat. No. Qty. 0380360000 20 Type AP (1.5) Cat. No. Qty. 0211360000 20 TW/AP (1.5) 1331760000 20 TSch 4 0363360000 100 Q2 Q3 Q4 0369000000 50 0369100000 50 0369200000 50 QB 21) insul. 0461100000 50 QB 31) insul. 0461200000 50 QB 41) insul. 0461300000 50 Q 10 0369300000 20 3-pole ganging with tag bar SchS 2, snapped onto three disconnect levers (Cat. No. 0337400000) QB 21) insul. 0482700000 QB 31) insul. 0482800000 QB 41) insul. 0482900000 QB 251) blank 0134000000 50 50 50 20 AD 4 0303400000 50 BSK M 2.5x18 0303300000 100 StB 8.5 0215700000 50 PS 2.3 0180400000 20 DEK 6 see “Accessories” DEK 5 see “Accessories” DEK 6.5 see “Accessories” 1) K sleeve 0553300000 100 PS 2.3 0180400000 20 DEK 6.5 see “Accessories” DEK 6.5 see “Accessories” The conductor cross-section is * With contact sleeve 19 A reduced to max. 2.5 mm2 when QB is used. 2) As disconnect test terminal: rated voltage 250 V 161 Feed-through terminals for TS 15 Tab connection Solder connection AKZ 4 SS AKZ 4 SS U Dimensions/approvals Width/length/height (mm) with TS 15 U Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage*/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size Continuous current rating of cross-connection 2-pole Continuous current rating of cross-connection multipole Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data A A UL CSA Type KrG PA Blue PA PA End plate (thickness mm) PA PA Blue PA HP HP BB AKZ 4 S ar 6/28.5/30.5 400 V/8 A/2.5/1 mm2 6 kV/3 U U U ar 6/28.5/30.5 AKZ 4 SF 400 V/8 A/1 mm2 6 kV/3 ar 6/27/30 r 6/27/30 9 mm/M 3/3.5 x 0.6 9 mm/M 3/3.5 x 0.6 400 V/8 A/4/1 mm2 6 kV/3 400 V/8 A/4/1 mm2 6 kV/3 0.5…1.0 2 0.5…1.0 2 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.2...4/A 3 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.2...4/A 3 Tab connec. 6.3 and 2.8 mm Tab connection 2.8 mm 20 20 20 20 20 20 20 20 150 V/10 A/22…12 AWG 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 150 V/10 A/22…12 AWG 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 150 V/20 A/22…12 AWG 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 0324560000 100 0362460000 100 0324460000 100 0158760000 100 Type AP (1.5) Cat. No. Qty. 0294460000 20 Type AP (1.5) Cat. No. Qty. 0294460000 20 Type AP (1.5) Cat. No. Qty. 0294460000 20 Type AP (1.5) Cat. No. Qty. 0294460000 20 TW (0.5) 0348260000 50 TW (0.5) 0348260000 50 TW (0.5) 0348260000 50 TW (0.5) 0348260000 50 Q Q Q Q 0369000000 0369100000 0369200000 0369300000 Q Q Q Q 0369000000 0369100000 0369200000 0369300000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Partition (thickness mm) PA HP HP Small partition Cross-connection 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 Switchable cross-connection link VL Test plug/socket StB BS VH Plug test socket ø 2.3 PS VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 IH 2.8 IH 6.3 0386060000 100 0386260000 100 IH 2.8 0386060000100 IH 2.8 0386060000 100 IH 2.8 IH 6.3 0386060000 100 0386260000 100 DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” Cover Insulation sleeves Marking tags DEK Print Standard Mounting rails, end brackets, further marking material see “Accessories” * Insulation sleeves are to be used for tab connections to maintain the rated voltage. 162 Feed-through terminals for TS 15 AKZ 1.5 L U U 6.5/32/21 400 V/16 A/1 mm2 6 kV/3 0.5…1 0.5…1 U TS 15 AKZ 4 L Cat. No. Qty. 0137320000 100 U EP (1.0) Cat. No. Qty. U r 5/34.5/25 ar 6/35.5/30 7 mm / M 2.5 / 3.0 x 0.5 9 mm / M 3 / 3.5 x 0.6 250 V/16 A/1.5 mm2 4 kV/3 250 V/16 A/4/1.5 mm2 4 kV/3 0.4…0.7 1 0.5…1.0 2 0.5…2.5 1.5 0.5…1.5 0.5…1.5 0.5…1.5 0.2…2.5 / A 1 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.2...4.0 / A 3 0.5…1.5 1.5 0.5…1.5 24 24 20 20 20 20 300 V/20 A/22…12 AWG 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 0334820000 100 0334860000 100 300 V/20 A/22…12 AWG 300 V/10 A/24…12 AWG U TS 15 Cat. No. Qty. 150 V/10 A/24…16 AWG U TS 15 Cat. No. Qty. 0340160000 100 Type AKZ 4 LL Type AP (1.5) Cat. No. Qty. 0329660000 20 ar 6/44/30 250 V/16 A/1.5 mm2 4 kV/3 SAK-series AL 1 0.2…2.5 / - Type AP (1.5) AP (1.5) AP (1.5) Cat. No. Qty. 0294420000 20 0294460000 20 0294480000 20 TW (0.5) 0346460000 100 Type Cat. No. Qty. AP (1.5) 0294460000 20 0348260000 50 TW (0.5) 0348260000 50 TSch 4 0363360000 100 TSch 4 0363360000 100 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 0164100000 100 EP(1.0 tropi. pr.) 0164500000100 TW (0.5) 0166800000 50 TW (0.5) Q Q Q Q DEK 6.5 see “Accessories” 2 3 4 10 0166800000 50 0368200000 0368300000 0368400000 0368500000 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5 x 14 0266800000 100 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 AD 4 0303400000 50 BSK M 2.5x18 0303300000 100 AD 4 0303400000 50 BSK M 2.5x18 0303300000 100 DEK 6 DEK 6 DEK 5 see “Accessories” see “Accessories” see “Accessories” 163 Feed-through terminals for TS 15 Solder connection Spring-clip connection AKZ 1.5 T AKZ 1.5 T AKZ 1.5 T AKZ 2.5 K acc. to DIN 41611 Part 4 Wrap connection acc. to DIN/IEC 352 Part 1 U U U * U Dimensions/approvals Width/length/height (mm) with TS 15 U Pin size Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size ar 5/25/45 0.8 x 1.6 7 mm/M 2.5/3.0 x 0.5 * 035786 = 45 mm a 5/25/39.5 1x1 7 mm/M 2.5/3.0 x 0.5 125 V/8 A/1.5 mm2 2.5 kV/3 125 V/8 A/1.5 mm2 2.5 kV/3 125 V/8 A/1.5 mm2 2.5 kV/3 125 V/10 A/2.5 mm2 2.5 kV/3 0.4…0.7 1 0.4…0.7 1 0.4…0.7 1 0.4…0.6 1 0.5…2.5 1.5 0.5…1.5 0.5…1.5 0.5…1.5 0.13...2.5 / A1 0.5…2.5 1.5 0.5…1.5 0.5…1.5 0.5…1.5 0.13...2.5 / A1 0.5…2.5 1.5 0.5…1.5 0.5…1.5 0.5…1.5 0.13...2.5 / A1 0.5…4 1.5…2.5 0.5…2.5 0.5…2.5 0.5…2.5 0.13...4.0 / A3 Continuous current rating of cross-connection 2-pole A Continuous current rating of cross-connection multipole A Rated data according to UL/CSA Voltage/current/conductor size UL Voltage/current/conductor size CSA Ordering data Pin versions 0.6 x 0.6 1.0 x 1.0 0.8 x 1.6 horizont. 0.8 x 1.6 vertical Mounting, Mounting, 0.8 x 2.4 horizontal horizontal vertical 0.8 x 2.4 vertical 24 24 24 24 24 24 24 24 300 V/10 A/26…14 AWG 300 V/10 A/24…16 AWG Type Cat. No. Qty. AKZ 1.5 T 0442560000 100 AKZ 1.5 T 0357960000 100 AKZ 1.5 W 0329460000 100 300 V/10 A/26…14 AWG Type AKZ 1.5 T AKZ 1.5 T Cat. No. Qty. 0483660000 100 0357860000 100 300 V/10 A/26…14 AWG 300 V/10 A/24…16 AWG Type Cat. No. Qty. AKZ 1.5 T 0400460000 100 AKZ 1.5 T 0400360000 100 300 V/10 A/26…14 AWG 300 V/10 A/26…10 AWG Type Cat. No. Qty. AKZ 2.5 K 0696260000100 AP (1.5) AP (1.5) 0340560000 50 AP (1.5) AP (2.5) 0697260000 50 TW (1.5) 0318560000 20 Q Q Q Q 0368200000 0368300000 0368400000 0368500000 ar 5/28/44 0.8 x 1.6 7 mm/M 2.5/3.0 x 0.5 ar 5/26/46.7 0.8 x 1.6 7 mm/M 2.5/3.0 x 0.5 End plate (thickness mm) PA 0340560000 50 0340560000 50 Partition (thickness mm) PA Small partition Cross-connection 2-pole 3-pole 4-pole 10-pole Q Q Q Q 2 3 4 10 0368200000 0368300000 0368400000 0368500000 50 50 50 20 Q Q Q Q 2 3 4 10 0368200000 0368300000 0368400000 0368500000 50 50 50 20 Q Q Q Q 2 3 4 10 0368200000 0368300000 0368400000 0368500000 50 50 50 20 2 3 4 10 50 50 50 20 Q3 Switchable cross-connection link VL BS Test plug/socket StB VH Plug test socket ø 2.3 PS Marking tags DEK Print Standard StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 DEK 5 see “Accessories” DEK 5 see “Accessories” DEK 5 see “Accessories” DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 164 Feed-through terminals for TS 15 AKZ 2.5 K AKZ 2.5 K AKZ 4 T U U U AKZ 4 T AKZ 4 T AKZ 4 ST U U U ar 5/47.5/27 0.8 x 1.6 7 mm/M 2.5/3.0 x 0.5 ar 6/27/48.5 1x1 9 mm/M 3/3.5 x 0.6 ar 6/27/50.5 0.8 x 1.6 9 mm/M 3/3.5 x 0.6 ar 6/27/57,8 0.8 x 2.4 9 mm/M 3/3.5 x 0.6 r 6/27/50.2 0.8 x 1.6 – 250 V/8 A/2.5 mm2 4 kV/3 250 V/8 A/2.5 mm2 4 kV/3 250 V/10 A/4 mm2 4 kV/3 250 V/10 A/4 mm2 4 kV/3 250 V/10 A/4 mm2 4 kV/3 250 V/10 A/2.5 mm2 4 kV/3 0.4…0.6 1 0.4…0.6 1 0.5…1.0 2 0.5…1.0 2 0.5…1.0 2 0.5…4 1.5…2.5 0.5…2.5 0.5…2.5 0.5…2.5 0.13...4.0 / A3 0.5…4 1.5…2.5 0.5…2.5 0.5…2.5 0.5…2.5 0.13...4.0 / A3 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.13...4.0 / A3 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.13...4.0 / A3 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.13...4.0 / A3 0.5...2.5 / - 24 24 24 24 20 20 20 20 20 20 20 20 300 V/10 A/26…14 AWG 300 V/10 A/26…10 AWG Type Cat. No. Qty. AKZ 2.5 K 0695460000 100 300 V/10 A/26…14 AWG 300 V/10 A/26…10 AWG Type Cat. No. Qty. 300 V/10 A/26…14 AWG 300 V/10 A/24…12 AWG Type Cat. No. Qty. 300 V/10 A/26…14 AWG 300 V/10 A/24…12 AWG Type Cat. No. Qty. 300 V/10 A/26…14 AWG 300 V/10 A/24…12 AWG Type Cat. No. Qty. 300 V/10 A/24…12 AWG Type Cat. No. Qty. AKZ 2.5 K AKZ 4 T AKZ 2.5 K 0695660000 100 AKZ 2.5 K 0695960000 100 0445860000 100 AKZ 4 T AKZ 4 T 0696160000 100 SAK-series ar 5/26/46.7 0.8 x 1.6 7 mm/M 2.5/3.0 x 0.5 AKZ 4 ST 0439260000 100 0344160000 100 0344060000 100 AKZ 4 T AKZ 4 T 0366460000 100 0461660000 100 AP (2.5) 0697260000 50 AP (2.5) 0697260000 50 AP (1.5) 0294460000 20 AP (1.5) 0294460000 20 AP (1.5) 0294460000 20 AP (1.5) 0294460000 20 TW (1.5) 0318560000 20 TW (1.5) 0318560000 20 TW (1.5) 0348260000 50 TW (1.5) 0348260000 50 TW (1.5) 0348260000 50 TW (1.5) 0348260000 50 TSch 4 0363360000 100 TSch 4 0363360000 100 TSch 4 0363360000 100 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 Q Q Q Q 0369000000 0369100000 0369200000 0369300000 Q Q Q Q 2 3 4 10 0368200000 0368300000 0368400000 0368500000 50 50 50 20 Q Q Q Q 2 3 4 10 0368200000 0368300000 0368400000 0368500000 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x14 0266800000 100 2 3 4 10 50 50 50 20 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 StB 8.5 0215700000 50 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 PS 2.3 0180400000 20 DEK 5 see “Accessories” DEK 5 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” 165 Feed-through terminals for TS 15 for temperature measuring circuits AKZ 4/TC U Weidmüller’s thermocouple terminals are specially designed for transmitting the smallest voltages in temperature measuring circuits. Special busbars ensure that no false signals occur in the terminal when temperature differences exist in the positive and negative path. This high measuring precision is necessary for, e.g. test beds for aircraft engines, for complicated chemical processes, control systems, etc. • Busbar material corresponds to thermal and compensating conductors • Clear thermocouple marking • 2-pole blocks per thermocouple • Row width 14 mm, incl. end plate Configuration of a temperature measuring circuit Dimensions Width/length/height (mm) with TS 15 U Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage/current/cross-section Further technical data Tightening torque range Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U Stranded H07V-R Flexible H07V-K Flexible H07V-K and ferrule DIN 46 228/1 Flexible H07V-K and ferrule with plastic insul. collar Plug gauge acc. to IEC 60 947-1 Continuous current of terminal for conductor size Continuous current rating of cross-connection 2-pole Continuous current rating of cross-connection multipole Ordering data Version for thermocouples Acc. to IEC 584 Type T (DIN 43710) Type K Type E 14/27/30 9 mm/M 3/3.5 x 0.6 –/–/4 mm2 Nm mm2 mm2 mm2 mm2 mm2 Size 0.5…1 2 0.5…4 1.5…4 0.5…4 0.5…2.5 0.5…2.5 A3 A A U TS 15 Type J Cu – CuNi NiCr – Ni NiCr – CuNi Fe – CuNi End plate 1 Thermocouple (sensor) 4 Reference point 2 Thermocouple terminals 5 Supply conductors (to and from) 3 Compensating conductor 6 Measuring device Cat. No. Qty. 1627010000 20 on demand 1677130000 20 on demand AP (thickness 1.5 mm) PA Cat. No. Qty. 0294460000 20 TW (thickness 0.5 mm) PA 0348260000 50 Partition The thermocouple terminals displayed in this measurement circuit are used to thermo-electrically transmit thermal e.m.f. of the thermocouple to the reference point and indicating device. Thermocouple terminals are required for the construction of temperature measuring circuits. Thermocouple, type J Thermocouple acc. to IEC 584 (DIN 43 710) Marking tags Busbar Constantan (CuNi) Iron (Fe) Mounting rails, end brackets, further marking material see “Accessories” 166 Print Material V0 DEK 5/6 1789590000 500 Multipole terminal blocks Screw connection MK 2/12 MK 10/14 MK 3/12 MK 4/16 103 18.5 8.5 85.5 10 Dimensions/approvals Width/length/height (mm) ar 86/15/15 ar 88.5/13.5/12 ar 110/15/16.1 ar 103/17/16 Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size 5 mm/M 2.5/3.5 x 0.6 6 mm/M 2.5/3.5 x 0.6 5 mm/M 2.5/3.5 x 0.6 5 mm/M 2.5/3.5 x 0.6 125 V/24 A/2.5 mm2 2.5 kV/3 125 V/24 A/2.5 mm2 2.5 kV/3 400 V/24 A/2.5 mm2 6 kV/3 400 V/24 A/2.5 mm2 6 kV/3 0.4…0.45 1 0.4…0.45 1 0.4…0.45 1 0.4…0.45 1 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.2…4.0 / A 2 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.2…4.0 / A 2 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.2…4.0 / A 2 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.2…4.0 / A 2 300 V/10 A/24…12 AWG 300 V/10 A/24…12 AWG Type Cat. No. Qty. 150 V/25 A/22…12 AWG 300 V/10 A/24…12 AWG Type Cat. No. Qty. 300 V/25 A/22…12 AWG 300 V/25 A/22…12 AWG Type Cat. No. Qty. MK 3/2 KrG 0273820000100 MK 3/3 KrG 0273920000 50 MK 3/4 KrG 0274020000 50 150 V/20 A/22…12 AWG 150 V/15 A/22…12 AWG Type Cat. No. Qty. Continuous current rating of cross-connection 2-pole A Continuous current rating of cross-connection multipole A Rated data according to UL/CSA Voltage/current/conductor size UL Voltage/current/conductor size CSA Ordering data Version 2-pole 3-pole 4-pole 4-pole 6-pole 6-pole 8-pole 8-pole 10-pole 12-pole 12-pole 14-pole 16-pole MK 3/6 KrG 0274220000 50 MK 3/8 KrG 0274420000 25 MK 3/10 KrG 0274620000 20 MK 3/12 KrG 0243520000 20 MK 2/12 PA 0241260000 50 MK 10/14 PA 0370160000 20 other numbers on request MK 4/16 KrG 0244220000 20 The MK 10/14 can be mounted with glue or with M 3 x 12* screws through the empty terminal point aperture *DIN EN ISO 1207 Soldering strip/expansion rivet MF 2/12 SN 0241760000 50 0200100000500 Marking strips printed 1 ... BSTb 28/12 0245700000 50 bottom BSTb 28/12 0278500000 50 top BSTb BSTb BSTb BSTb 28/12 28/8 28/6 28/4 0245900000 0290200000 0290000000 0289800000 50 50 50 50 BSTb 28/16 0262200000 50 bottom BSTb 28/16 0278700000 50 top unprinted BSTo 28/12 0245600000 50 BSTo BSTo BSTo BSTo 28/12 28/8 28/6 28/4 0245800000 0284700000 0289500000 0289300000 50 50 50 50 BSTo 28/16 0262100000 50 Printed on top on request 167 SAK-series 80 Multipole terminal blocks Screw/tab connection MK 5/2 KS 2…10 BK 2…12 MK 6/2…6/6 Dimensions/approvals Width/length/height (mm) 40/18/15.5 ar see table below ari# see table below ar see table below 5 mm/M 2.5/3.5 x 0.6 8 mm/M 3/4.0 x 0.8 8 mm/M 3/4.0 x 0.8 9 mm/M 4/4.0 x 0.8 500 V/24 A/2.5 mm2 6 kV/3 500 V/24 A/2.5 mm2 6 kV/3 400 V/32 A/4 mm2 6 kV/3 690 V/41 A/6 mm2 8 kV/3 0.4…0.45 1 0.5…0.7 2 0.5…0.7 2 1.2…2.0 4 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.2…4.0 / A 2 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.2 0.2…4.0 / A 2 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.33…4.0 / A 3 0.5…6 1.5…6 0.5…6 0.5…4 0.5…4 0.33…6.0 / A 3 Type Cat. No. Qty. MK 5/2 KrG 0243820000100 300 V/20 A/22…12 AWG 300 V/25 A/24…12 AWG Type Cat. No. Qty. KS 2 KrG2) 0134420000100 300 V/30 A/22…10 AWG 300 V/40 A/22…10 AWG Type Cat. No. Qty. MK 6/2 KrG 0620420000 50 MK 6/3 KrG 0620320000 50 MK 6/4 KrG 0620220000 20 MK 6/6 KrG 0620120000 20 Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data Cover D 2 (for MK 5/2) Cover D 4 (for KS 4) UL CSA Versions 2-pole 3-pole 4-pole 4-pole 6-pole 6-pole 8-pole 8-pole 10-pole 12-pole 12-pole Cover D2(forMK 5/2)0244060000 50 Cover KS 4 KrG2) 0140320000 50 300 V/10 A/22…12 AWG 300 V/10 A/22…12 AWG Type Cat. No. Qty. BK 2 KrG 0624720000 50 BK 3 KrG 0624920000 50 BK 4 KrG 0625120000 50 KS 6 KrG2) 0140620000 50 BK 6 KrG 0625220000 50 BK 12 KrG 0625320000 50 Dimensions Type BK 2 BK 3 BK 4 BK 6 BK 12 a 20 31 38 52 92 SN 0200100000 500 BSTb 28/2 BSTb 28/3 BSTb 28/4 BSTb 28/6 BSTb 28/12 BSTo 28/2 BSTo 28/3 BSTo 28/4 BSTo 28/6 BSTo 28/12 0203600000 0203800000 0197300000 0197500000 0198800000 0203500000 0203700000 0197200000 0197400000 0198700000 KS 10 KrG2) 0141620000 20 Cover D 2 (for KS 2) 0134500000100 D 4 (for KS 4) 0140500000 50 D 6 (for KS 6) 0140800000 50 D10 (for KS10) 0141800000 20 Marking tag cover Dimensions Type a KS 2 42 KS 4 66 KS 6 90 KS 10 138 b 32 56 80 128 b – 11 18 32 72.5 Dimens. Length/attach.dim. Type KRG MK 6/2 23.5 MK 6/3 36.5 13 MK 6/4 49.5 26 MK 6/6 75.5 52 Expansion rivet Marking strips printed 1… ELSb ELSb ELSb ELSb 2 4 6 10 0143200000 0143300000 0143400000 0143500000 50 50 50 50 unprinted ELSo ELSo ELSo ELSo 2 4 6 10 0142800000 0142900000 0143000000 0143100000 50 50 50 50 50 50 50 50 50 50 50 50 50 50 BSTb 17/6 Mounting rails, end brackets, further marking material see “Accessories” 168 1) Projecting length = 1 mm. To be considered for the last terminal in a row! Printed on top on request 2) Please order cover and marking strips separately. 0304600000 50 Multipole terminal blocks MF 1/6…1/12 SLS 2/2 SLS 2/4 ar see below Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage*/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data UL CSA PA ar see below 8 mm/M 3.5/4.0 x 0.8 400 V*/16 A/2.5/1 mm2 6 kV/3 0.8…1.6 3 0.5…4 1.5…4 0.5…4 0.5…4 0.5…4 0.33...4.0 / A 3 300 V/10 A/24…12 AWG 300 V/10 A/22…10 AWG Type Cat. No. Qty. MF 1/6 KrG2) 0479720000100 MF 1/6 KrG3) 0480020000100 MF 1/8 KrG2) 0479820000 50 MF 1/8 KrG3) 0480120000 50 MF1/12 KrG2) 0479920000 50 MF1/12 KrG3) 0480220000 50 Dimensions Type a b MF 1/6 52 34 MF 1/8 68 50 MF 1/12 113+0.5 102 Expansion rivet/insulation sleeve IH 400 V*/16 A/4 mm2 6 kV/3 IH 2.8 IH 6.3 SN SAK-series Max. technical data Dimensions/approvals Width/length/height (mm) 300 V/10 A/22…10 AWG Type Cat. No. Qty. SLS 2/2 KrG 0213420000 100 SLS 2/4 KrG 0240420000 50 SLS 2/4 KrG 0480320000 50 Slotted c d 9.5 6.5 9.5 6.5 8 7.5 0386060000 100 0386260000 100 0200100000500 IH 2.8 IH 6.3 0386060000 100 0386260000 100 Cover/marking strips BSTb 10/6 0240900000 50 BSTb 10/8 0241100000 50 BSTb 10/12 0209500000 50 BSTo 10/6 0240800000 50 BSTo 10/8 0241000000 50 BSTo 10/12 0209400000 100 Mounting rails, end brackets, further marking material see “Accessories” * Insulation sleeves are to be used for tab connections to maintain the rated voltage. 2) 3) Single tab Double tab 169 Multipole terminal blocks Screw, solder, tab connection MKL 2/12 Dimensions/approvals Width/length/height (mm) Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage*/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data Horizontal Other number of poles on demand Vertical Other number of poles on demand UL CSA Versions 2-pole 4-pole 6-pole 12-pole 16-pole MF 2/12 MKL 3/12 MKL 4/16 0241860000 0243620000 0262020000 0241760000 0249920000 0244320000 ar 103/24/16.5 88/23/15 75/24/6 ar 110/23/16 5 mm/M 2.5/3.5 x 0.6 5 mm 5mm/M 2.5/3.5 x 0.6 5mm/M 2.5/3.5 x 0.6 125 V/20 A/2.5/1.5/1 mm2 2.5 kV/3 63 V/17.5 A/1.5/1 mm2 1.5 kV/3 400 V* / 20 A / 2.5/ 1.5/ 1 mm2 6 kV/3 400 V/20 A/2.5/1.5/1 mm2 6 kV/3 0.4…0.45 1 0.4…0.45 1 0.4…0.45 1 0.5…2.5 1.5…2.5 0.5…2.5 0.5…2.5 0.5…2.5 0.2...2.5 / A 2 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.33...4.0 / A 2 0.5…4 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.33...4.0 / A 2 300 V/25 A/22…12 AWG 300 V/25 A/22…12 AWG Type Cat.No. Qty. MKL3/2 KrG 0274920000**100 MKL 3/4KrG 0275120000**100 MKL 3/6 KrG 0275320000** 50 MKL 3/12KrG 0243620000** 20 300 V/25 A/22…12 AWG 150 V/15 A/22…12 AWG Type Cat. No. Qty. Type Cat. No. Qty. Type Cat. No. Qty. MKL 2/12 PA 0241360000 50 MKL 4/16 KrG 02620200001)20 2-pole 4-pole 6-pole 12-pole 16-pole MKL 3/2 KrG 0276020000* 100 MKL 3/6 KrG 0276420000* 50 MKL3/12KrG 0249920000* 20 MKL 4/16 KrG 0244320000 20 double-sided 2.8 x 0 . 8 single-sided 0.8 x 1.6/2.8 x 0 . 8 MF 2/12 PA 0241860000 50 MF 2/12 PA 0241760000 50 * For terminals directly mounted next to each other, the rated voltage is reduced to 250 V. ** Rated voltage 250 V. For terminals directly mounted next to each other, the rated voltage is reduced to 125 V. Expansion rivet/insulation sleeve SN 0200100000 500 IH IH 2.8 0386060000 100 Marking strips printed 1… BSTb 28/12 0245700000 50 bottom top 0278500000 50 BSTb 28/4 0289800000 50 BSTb 28/6 0290000000 50 BSTb 28/12 0245900000 50 BSTb 28/16 0262200000 50 bottom top unprinted BSTo 28/12 0245600000 50 BSTo 28/4 0289300000 50 BSTo 28/6 0289500000 50 BSTo 28/12 0245800000 50 BSTo 28/16 0262100000 50 Mounting rails, end brackets, further marking material see “Accessories” * Insulation sleeves are to be used for tab connections to maintain the rated voltage. 170 1) Rated voltage 250 V Screw, solder, tab connection Modular design AKB 4 AKZ 2.5 ASK 1 Max. technical data 32 A / 4 mm2 ar 6/27/23 – 9 mm/M 3/3.5 x 0.6 26 A / 2.5 mm2 ar 5/25.5/26.5 – 7 mm/M 2.5/3 x 0.5 ar 8/58/30.5 – 9 mm/M 3/3.5 x 0.6 400 V/32 A/4 mm2 6 kV/3 250 V/24 A/2.5 mm2 4 kV/3 500 V/6.3 A*/4 mm2 6 kV/3 0.5…1.0 2 0.4…0.6 1 0.5…1.0 2 0.5…6 1.5…4 0.5…4 0.5…4 0.5…4 0.33...4.0 / A3 0.5…4 1.5…2.5 0.5…2.5 0.5…2.5 0.5…2.5 0.13...4.0 / A3 0.5…4 1.5…4 0.5…4 0.5…2.5 0.5…2.5 0.13...4.0 / A3 32 32 24 24 (QB 2…4) 10 300/250 V/27 A/22…12 AWG 300 V/10 A/22…12 AWG Type Cat. No. Qty. AKB 4 PA 0321560000 100 0321580000 100 Direct mounting with BB 1 please order separately 300 V/10 A/22…12 AWG 300 V/10 A/26…10 AWG Type Cat. No. Qty. AKZ 2.5 0697160000 100 AKZ 2.5 0697180000 100 Direct mounting with BB 4 please order separately 300 V/10 A/22…12 AWG 300 V/6.3 A/26…12 AWG Type Cat. No. Qty. ASK 1 PA 0376960000 100 BB 1 (7) 0320560000 50 BS M 3 x 15 0359000000 100 BB 4 (7.5) 0697560000 50 AP (2.5) AP (2.5) 0697360000 50 0697380000 50 AP (1.5) 0380360000 20 Q Q Q Q 0368200000 0368300000 0368400000 0368500000 QB 21) QB 31) QB 41) 0461100000 50 0461200000 50 0461300000 50 Dimensions/approvals Width/length/height (mm) Insulation stripping length/clamping screw/screwdriver blade Rated data according to IEC 60 947-7-1 Rated voltage/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size Continuous current rating of cross-connection 2-pole Continuous current rating of cross-connection multipole Rated data according to UL/CSA Voltage/current/conductor size Voltage/current/conductor size Ordering data A A UL CSA PA Blue PA SAK-series Multipole terminal blocks (for G fuse inserts 5x 20 without indicator) End plate/attachment bracket (thickness mm) AP PA Blue PA Partition (thickness mm) TW PA (0.5) 0348260000 50 Small partition Cross-connection Q3 QB 4 TSch 4 0363360000 100 Q Q Q Q 0336400000 0336500000 0336600000 0368600000 2 3 4 10 50 50 50 20 2 3 4 10 50 50 50 20 Switchable cross-connection link VL BS VL 2 0446700000 50 VH 10 0446600000 50 BS M 2.5x 14 0266800000 100 VH For fixing the screws of ASK 1 please use M 3 x ... DIN EN. ISO 1207 or M 3 x ... DIN EN, ISO 1580 Test plug/socket PS StB StB 8.5 PS 2.3 0215700000 50 0180400000 20 StB 8.5 PS 2.3 0215700000 50 0180400000 20 Cover/contact sleeve Marking tags DEK K sleeve AD 4 0303400000 50 BSK M2.5x18 0303300000 100 Print Standard DEK 6 see “Accessories” DEK 5 see “Accessories” Mounting rails, end brackets, further marking material see “Accessories” 1) The conductor cross-section is reduced to max. 2.5 mm2 when QB is used. K sleeve 0553300000 100 DEK 6.5 see “Accessories” * With contact sleeve 19 A 171 Feed-through terminals Screw connection Solder connection Tab connection Spring-clip connection AKA 2.5 ADK 1 ADK 1 F ADK 3 F ADK 1 S ar 6/20/31 7,8 9 mm/M 2.5/3.5 x 0.6 ar 6/22/36.5 8,4 9 mm/M 3.5/3.5 x 0.6 ar 6/22/36.5 8.5/7.5 11 mm/M 2.5/3.5 x 0.6 ar 6/22/36.5 8,4 – 400 V/20 A/2.5/1.5 mm2 6 kV/3 400 V/16 A/4/1.5 mm2 6 kV/3 400 V/20 A/2.5/1.5 mm2 6 kV/3 400 V/16 A/2.5/1.5/1 mm2 6 kV/3 0.4 1 0.5…1.0 2 0.4…0.6 1 – – 0.5…2.5 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.13...2.5 / A2 0.5…4 1.5…4 0.5…4 0.5…2.5 0.5…2.5 0.13...2.5 / A3 0.5…2.5 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.13...2.5 / A2 0.5...2.5 / - 10 10 300 V/20 A/26…12 AWG 300 V/10 A/24…12 AWG Cat. No. 1.5 Qty. 300 V/10 A/26…12 AWG 300 V/15 A/26…12 AWG 1.5 Qty. 2.5 Qty. 300 V/20 A/26…14 AWG 300 V/15 A/22…14 AWG 1.5 Qty. 2.5 Qty. 300 V/18 A/12 AWG max. 300 V/3 A/– 1.5 Qty. 2.5 Qty. 0303860000100 0301060000100 0476060000100 0478660000100 acc. to DIN 41 611 Part 4 Wrap connection acc. to DIN/IEC 352 Part 1 Dimensions/approvals Width/length/height with Pins (mm) Length solder tag/pin (mm) Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage*/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Max. clamping range in mm2/plug gauge acc. to IEC 60 947-1 Size Continuous current rating of cross-connection 2-pole A Continuous current rating of cross-connection multipole A Rated data according to UL/CSA Voltage/current/conductor size UL Voltage/current/conductor size CSA Ordering data Version for plate thickn. mm PA KrG Pin 1.0x1.0 Pin 0.8x1.6 FS 1x6.3 slotted/0.8x2.8 0300720000 100 0476160000100 0478560000100 12-pole PA End plate (thickness mm) KrG PA EP Type AP (3) Cat. No. Qty. 0162520000 100 Type Cat. No. Qty. Type AP (3) 0476260000 50 TW (0.5) 0442300000 50 PS 2.3 0180400000 20 Cat. No. Qty. Type Cat. No. Qty. AP (3) AP (3) 0476260000 50 0360000000 20 AP (3) 0476260000 50 TW (0.5) 0442300000 50 TW (0.5) 0442300000 50 Spacer (thickness mm) KrG KrG ZP (1.5) ZP (2.5) 0240720000 50 0288520000 20 Partition (thickness mm) TW Test plug/socket StB Plug test socket ø 2.3 PS Fuse pin/insulation sleeve/expansion rivet SST 1.2 0306600000 SST 1.2 IH 2.8 0306600000 0386060000 100 SST 1.2 IH 2.8 0306600000 0386060000 100 SST 1.2 IH 2.8 IH 6.3 030660 0386060000 100 0386260000 100 DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” DEK 6 see “Accessories” IH Marking tags DEK Print Standard Mounting rails, end brackets, further marking material see “Accessories” * Insulation sleeves are to be used for tab connections to maintain the rated voltage. 172 Feed-through terminals ADK 1 T AKZ 2.5 K ADK 1 FT MK 2/12 ar 6/22/50.5 19.5…21.9 9 mm/M 3/3.5 x 0.6 ar 5/26/45.5 22.4…23.6 7 mm/M 2.5/3.0 x 0.5 r 6/22/52 24 11 mm/M 2.5/3.5 x 0.6 ar 86/15/23 8 5 400 V/8 A/4 mm2 6 kV/3 250 V/8 A/2.5 mm2 4 kV/3 250 V/10 A/2.5 mm2 4 kV/3 63 V/20 A/2.5/1.5 mm2 1.5 kV/3 0.5…1.0 2 0.4…0.6 1 0.4…0.6 1 0.4…0.45 1 0.5…4 1.5…4 0.5…4 0.5…2.5 0.5…2.5 0.13...4.0 / A3 0.5…2.5 1.5…2.5 0.5…2.5 0.5…2.5 0.5…2.5 0.13...2.5 / A2 0.5…2.5 1.5…2.5 0.5…2.5 0.5…1.5 0.5…1.5 0.33...2.5 / A2 0.5…2.5 1.5…2.5 0.5…2.5 0.5…2.5 0.5…2.5 0.2...2.5 / A2 10 10 300/250 V/10 A/26…12 AWG 300 V/15 A/26…12 AWG 1.5 Qty. 2.5 Qty. 300/250 V/10 A/22…12 AWG 300 V/10 A/26…10 AWG Cat. No. Qty. 0109160000 solder tag 100 300 V/3 A/22…14 AWG Cat. No. 1.5 Qty. 300 V/10 A/24…12 AWG 300 V/10 A/24…12 AWG Cat. No. Qty. 0372260000 100 0366360000 100 0108960000 0176960000 100 100 0241460000 Type Cat. No. Qty. Type AP (3) 0476260000 50 TW (0.5) Cat. No. Qty. Type AP (3) 0697260000 50 AP (3) 0476260000 50 0442300000 50 TW (1.5) 0318560000 20 TW (0.5) 0442300000 50 PS 2.3 0180400000 20 PS 2.3 StB 8.5 0180400000 20 0215700000 50 SST 1.2 0306600000 SST 1.2 0306600000 IH 2.8 0386060000 100 Cat. No. Qty. Type SN DEK 6 see “Accessories” DEK 5 see “Accessories” DEK 6 SAK-series 0109160000 solder tag see “Accessories” 50 Cat. No. Qty. 0200100000 500 BSTb 28/12 024570… BSTo 28/12 024560… 50 50 173 Rack-mounted interface systems Dimensions Width/length/height (mm) Hole spacing/mounting dimensions mm Insulation stripping length/clamping screw/screwdriver blade Rated data Rated voltage*/current/cross-section Rated impulse voltage VDE 0110/1.89/pollution severity Further technical data Tightening torque range Nm Torque setting with electric screwdriver type DMS 2 Clampable conductor Solid H07V-U mm2 Stranded H07V-R mm2 Flexible H07V-K mm2 Flexible H07V-K and ferrule DIN 46 228/1 mm2 Flexible H07V-K and ferrule with plastic insul. collar mm2 Plug gauge acc. to IEC 60 947-1 Size Ordering data Pin 1.0 x 1.0 Pin 0.8 x 2.8 (push-on), unprinted Pin 0.8 x 2.8 (push-on), printed, 1…32 Pin 0.8 x 2.8 (push-on), printed, 1…32, blue 6 x plug (6.3 x 0.8) 6 x plug (6.3 x 0.8), blue 6 x plug (6.3 x 0.8), bzw. 12 x 2.8 x 0.8 slotted 6 x plug (6.3 x 0.8), bzw. 12 x 2.8 x 0.8 slotted, blue 3 x plug (6.3 x 0 . 8) /1 x solder per pole 3 x plug (6.3 x 0 . 8) /1 x solder per pole, blue 3 x plug (6.3 x 0.8 bzw. 6 x 2.8 x 0.8)/1 x solder 3 x plug (6.3 x 0.8 bzw. 6 x 2.8 x 0.8)/1 x solder, blue 2 x direct connection, 1 x Pin 0.8 x 1.6 Version PA PA PA PA KrG KrG KrG KrG KrG KrG KrG KrG PA TOP 1.5 F/32 SP 10 FF2) SP 10 LF3) SP 60 FF2) SP 60 LF3) SP 90 FF2) SP 90 LF3) 40.2/110.6/29.5 101.6/20.3 10 mm/M 2.5/3.5 x 0.6 42/46.5/170/28 147 40/45.5/162.5/110 151/90 40/45.5/228.5/110 217/90 250* V/6 A/1.5/1 mm2 4 kV/3 1000* V/16 A/2.5/1.5 mm2 6 kV/3 400* V/16 A/2.5/1.5 mm2 6 kV/3 400* V/16 A/2.5/1.5 mm2 6 kV/3 0.4…0.7 1 0.5…2.5 1.5 0.5…1.5 0.5…1.5 0.5…1.5 A1 Type Cat. No. Qty. TOP 1.5 F/32 04431600001) 5 Type SP 10 FF Cat. No. Qty. 0456220000 10 Type Cat. No. SP 60 FF 4) SP 60 FF 4) SP SP SP SP 60 60 60 60 LF 4) LF 4) LF 5) LF 5) Qty. 0340320000 1 0340370000 1 0343720000 0343770000 0124520000 0124570000 1 1 1 1 Type Cat. No. Qty. SP 90 FF** 0248120000 1 SP 90 FF** 0608920000 1 SP 90 LF** 0248220000 1 printed: ** A ...F / 1...15 printed: 4) A...F / 1...10 5) 00...50 / 1...10 Insulation sleeves Marking tags dekafix Type IH 2.8 Cat. No. Qty. 0386060000 100 Print for group markers Type IH 2.8 IH 6.3 Cat. No. Qty. 0386060000 100 0386260000 100 FW 5 see “Accessories” Type IH 2.8 IH 6.3 Cat. No. Qty. 0386060000 100 0386260000 100 Type IH 2.8 IH 6.3 Cat. No. Qty. 0386060000 100 0386260000 100 Mounting rails, end brackets, further marking material see “Accessories” * Insulation sleeves are to be used for tab connections to maintain the rated voltage. 174 1) Rated voltage 125 V 2) 3) FF = Tab- Tab LF = Solder - Tab Rack-mounted interface systems RV 8/8 long RV 8/9 long RV 8/8 short Technical data acc. to VDE 125 V/–/– Pin versions (intern) 0.8 x 2.4/1 x 1 0.8 x 2.4/0.8 x 2.4 Plug adapter 1-pole RV 8/9 short 125 V/–/– Type Cat. No. Qty. 0468860000 1 0468960000 1 Type Cat. No. Qty. 0467160000 1 0467260000 1 Type DSA 1 Cat. No. Qty. 0576060000 50 Type DSA 1 Cat. No. Qty. 0576060000 50 105 V/–/– Type Cat. No. Qty. 0498960000 1 0499060000 1 with shield pins Type Cat. No. Qty. DSA 1 0576060000 50 125 V/–/– Type Cat. No. Qty. 0444060000 1 0545960000 1 with shield pins Type Cat. No. Qty. DSA 1 0576060000 50 RV 8/20 short SAK-series for connection of solid and flexible conductors from 0.75 to 1.5 mm2 directly on to the pins of the interface system. RV 8/56 short Technical data acc. to VDE 125 V~/–/– Pin versions (internal) 0.8 x 2.4/1 x 1 0.8 x 2.4/0.8 x 2.4 125 V~/–/– Cat. No. Qty. 0544460000 Cat. No. 0462260000 0533060000 1 Qty. 1 4 Additional versions on request Size A Type in mm RV 8/8 K 81 RV 8/9 K 89 RV 8/8 L 93 RV 8/9 L 100 RV 8/20 K 187,62/31.5 RV 8/56 K 460/31.5 (K = short/L = long) Cat. No. 0468860000 0468960000 0467160000 0467260000 0119360000 0544460000 0462260000 0533060000 RV 8/8 L 8/8 L 8/8 K 8/8 K 8/20 K 8/20 K 8/56 K 8/56 K Size B in mm 40.64 40.64 40.64 40.64 63 63 a 26 26 26 26 26 26 26 26 b 20 26 20 26 20 26 20 26 c 200 206 84 89 84 89 84 89 Mounting rails, end brackets, further marking material see “Accessories” 175