W78LE516-24

Preliminary W78LE516 8-BIT MICROCONTROLLER GENERAL DESCRIPTION The W78LE516 is an 8-bit microcontroller which has an in-system programmable MTP-ROM for firmware updating. The instruction set of the W78LE516 is fully compatible with the standard 8052. The W78LE516 contains a 64K bytes of main MTP-ROM and a 4K bytes of auxiliary MTP-ROM which allows the contents of the 64KB main MTP-ROM to be updated by the loader program located at the 4KB auxiliary MTP-ROM; 512 bytes of on-chip RAM; four 8-bit bi-directional and bitaddressable I/O ports; an additional 4-bit port P4; three 16-bit timer/counters; a serial port. These peripherals are supported by a eight sources two-level interrupt capability. To facilitate programming and verification, the MTP-ROM inside the W78LE516 allows the program memory to be programmed and read electronically. Once the code is confirmed, the user can protect the code for security. The W78LE516 microcontroller has two power reduction modes, idle mode and power-down mode, both of which are software selectable. The idle mode turns off the processor clock but allows for continued peripheral operation. The power-down mode stops the crystal oscillator for minimum power consumption. The external clock can be stopped at any time and in any state without affecting the processor. FEATURES • Fully static design 8-bit CMOS microcontroller • 64K bytes of in-system programmable MTP-ROM for Application Program (APROM) • 4K bytes of auxiliary MTP-ROM for Loader Program (LDROM) • 512 bytes of on-chip RAM. (including 256 bytes of AUX-RAM, software selectable) • 64K bytes program memory address space and 64K bytes data memory address space • Four 8-bit bi-directional ports • One 4-bit multipurpose programmable port • Three 16-bit timer/counters • One full duplex serial port • Eight-sources, two-level interrupt capability • Built-in power management • Code protection • Packaged in − DIP 40: W78LE516-24 − PLCC 44: W78LE516P-24 − QFP 44: W78LE516F-24 -1- Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 PIN CONFIGURATIONS 40-Pin DIP (W78LE516) T2, P1.0 T2EX, P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 RST RXD, P3.0 TXD, P3.1 INT0, P3.2 INT1, P3.3 T0, P3.4 T1, P3.5 WR, P3.6 RD, P3.7 XTAL2 XTAL1 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 VDD P0.0, AD0 P0.1, AD1 P0.2, AD2 P0.3, AD3 P0.4, AD4 P0.5, AD5 P0.6, AD6 P0.7, AD7 EA ALE PSEN P2.7, A15 P2.6, A14 P2.5, A13 P2.4, A12 P2.3, A11 P2.2, A10 P2.1, A9 P2.0, A8 44-Pin PLCC (W78LE516P) T 2 E X , PP 11 .. 21 4 3 / I N T 3 , P 4V .D 2D 44-Pin QFP (W78LE516F) T 2 E X , PP 11 .. 21 / I N T 3 , P 4V .D 2D A D 0 , P 0 . 0 A D 1 , P 0 . 1 A D 2 , P 0 . 2 A D 3 , P 0 . 3 P 1 . 4 6 7 8 9 10 11 12 13 14 P 1 . 3 5 T 2 , P 1 . 0 2 A D 0 , P 0 . 0 A D 1 , P 0 . 1 A D 2 , P 0 . 2 A D 3 , P 0 . 3 1 2 P 1 . 4 P 1 . 3 T 2 , P 1 . 0 P1.5 P1.6 P1.7 RST RXD, P3.0 INT2, P4.3 TXD, P3.1 INT0, P3.2 INT1, P3.3 T0, P3.4 T1, P3.5 1 44 43 42 41 40 39 38 37 36 35 34 33 32 P0.4, AD4 P0.5, AD5 P0.6, AD6 P0.7, AD7 EA P4.1 ALE PSEN P2.7, A15 P2.6, A14 P2.5, A13 P1.5 P1.6 P1.7 RST RXD, P3.0 INT2, P4.3 TXD, P3.1 INT0, P3.2 INT1, P3.3 T0, P3.4 T1, P3.5 44 43 42 41 40 39 38 37 36 35 34 33 32 31 3 30 4 29 5 28 6 27 7 26 8 9 25 10 24 23 11 12 13 14 15 16 17 18 19 20 21 22 P 3 . 6 , / W R P 3 . 7 , / R D X T A L 2 XV TS AS L 1 P 4 . 0 P 2 . 0 , A 8 P 2 . 1 , A 9 P 2 . 2 , A 1 0 P 2 . 3 , A 1 1 P 2 . 4 , A 1 2 P0.4, AD4 P0.5, AD5 P0.6, AD6 P0.7, AD7 EA P4.1 ALE PSEN P2.7, A15 P2.6, A14 P2.5, A13 31 15 30 16 29 17 18 19 20 21 22 23 24 25 26 27 28 P 3 . 6 , / W R P 3 . 7 , / R D X T A L 2 X T A L 1 VPP S42 S. . 00 , A 8 P 2 . 1 , A 9 P 2 . 2 , A 1 0 P 2 . 3 , A 1 1 P 2 . 4 , A 1 2 -2- Preliminary W78LE516 PIN DESCRIPTION SYMBOL EA TYPE I DESCRIPTIONS EXTERNAL ACCESS ENABLE: This pin forces the processor to execute the external ROM. The ROM address and data will not be presented on the bus if the EA pin is high. PROGRAM STORE ENABLE: PSEN enables the external ROM data in the Port 0 address/data bus. When internal ROM access is performed, no PSEN strobe signal outputs originate from this pin. ADDRESS LATCH ENABLE: ALE is used to enable the address latch that separates the address from the data on Port 0. ALE runs at 1/6th of the oscillator frequency. RESET: A high on this pin for two machine cycles while the oscillator is running resets the device. CRYSTAL 1: This is the crystal oscillator input. This pin may be driven by an external clock. CRYSTAL 2: This is the crystal oscillator output. It is the inversion of XTAL1. GROUND: ground potential. POWER SUPPLY: Supply voltage for operation. PSEN OH ALE OH RST XTAL1 XTAL2 VSS VDD P0.0−P0.7 P1.0−P1.7 P2.0−P2.7 P3.0−P3.7 P4.0−P4.3 IL I O I I I/O D PORT 0: Function is the same as that of standard 8052. I/O H PORT 1: Function is the same as that of standard 8052. I/O H PORT 2: Port 2 is a bi-directional I/O port with internal pull-ups. This port also provides the upper address bits for accesses to external memory. I/O H PORT 3: Function is the same as that of the standard 8052. I/O H PORT 4: A bi-directional I/O. See details below. * Note: TYPE I: input, O: output, I/O: bi-directional, H: pull-high, L: pull-low, D: open drain PORT4 Another bit-addressable port P4 is also available and only 4 bits (P4) can be used. This port address is located at 0D8H with the same function as that of port P1, Example: P4 MOV MOV SETB CLR REG 0D8H P4, #0AH A, P4 P4.0 P4.1 ; Output data "A" through P4.0−P4.3. ; Read P4 status to Accumulator. ; Set bit P4.0 ; Clear bit P4.1 -3- Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 BLOCK DIAGRAM P1.0 Port 1 Port 1 Latch ACC Interrupt T1 Timer 2 Timer 0 Timer 1 UART PSW ALU Stack Pointer T2 P1.7 B Port 0 Latch Port 0 P0.0 P0.7 DPTR Temp Reg. PC Incrementor Addr. Reg. P3.0 Port 3 Port 3 Latch Instruction Decoder & Sequencer SFR RAM Address 64KB MTP-ROM 4KB MTP-ROM P3.7 512 bytes RAM & SFR P2.0 Port 2 Latch Port 2 Bus & Clock Controller P2.7 P4.0 P4.3 Port 4 Port 4 Latch Oscillator Reset Block Power control XTAL1 XTAL2 ALE PSEN RST VCC Vss FUNCTIONAL DESCRIPTION The W78LE516 architecture consists of a core controller surrounded by various registers, four general purpose I/O ports, one special purpose programmable 4-bits I/O port, 512 bytes of RAM, three timer/counters, a serial port. The processor supports 111 different opcodes and references both a 64K program address space and a 64K data storage space. RAM The internal data RAM in the W78LE516 is 512 bytes. It is divided into two banks: 256 bytes of scratchpad RAM and 256 bytes of AUX-RAM. These RAMs are addressed by different ways. • RAM 0H−7FH can be addressed directly and indirectly as the same as in 8051. Address pointers are R0 and R1 of the selected register bank. -4- Preliminary W78LE516 • RAM 80H−FFH can only be addressed indirectly as the same as in 8051. Address pointers are R0, R1 of the selected registers bank. • AUX-RAM 0H−FFH is addressed indirectly as the same way to access external data memory with the MOVX instruction. Address pointer are R0 and R1 of the selected register bank and DPTR register. An access to external data memory locations higher than FFH will be performed with the MOVX instruction in the same way as in the 8051. The AUX-RAM is disable after a reset. Setting the bit 4 in CHPCON register will enable the access to AUX-RAM. When AUX-RAM is enabled the instructions of "MOVX @Ri" will always access to on-chip AUX-RAM. When executing from internal program memory, an access to AUX-RAM will not affect the Ports P0, P2, WR and RD . Example, CHPENR CHPCON MOV MOV ORL MOV MOV MOV MOVX REG F6H REG BFH CHPENR,#87H CHPENR,#59H CHPCON,#00010000B ; enable AUX-RAM CHPENR,#00H R0,#12H A,#34H @R0,A ; Write 34h data to 12h address. Timers 0, 1, and 2 Timers 0, 1, and 2 each consist of two 8-bit data registers. These are called TL0 and TH0 for Timer 0, TL1 and TH1 for Timer 1, and TL2 and TH2 for Timer 2. The TCON and TMOD registers provide control functions for timers 0, 1. The T2CON register provides control functions for Timer 2. RCAP2H and RCAP2L are used as reload/capture registers for Timer 2. The operations of Timer 0 and Timer 1 are the same as in the W78C51. Timer 2 is a 16-bit timer/counter that is configured and controlled by the T2CON register. Like Timers 0 and 1, Timer 2 can operate as either an external event counter or as an internal timer, depending on the setting of bit C/T2 in T2CON. Timer 2 has three operating modes: capture, auto-reload, and baud rate generator. The clock speed at capture or auto-reload mode is the same as that of Timers 0 and 1. Clock The W78LE516 is designed with either a crystal oscillator or an external clock. Internally, the clock is divided by two before it is used by default. This makes the W78LE516 relatively insensitive to duty cycle variations in the clock. Crystal Oscillator The W78LE516 incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must be connected across pins XTAL1 and XTAL2. In addition, a load capacitor must be connected from each pin to ground. External Clock An external clock should be connected to pin XTAL1. Pin XTAL2 should be left unconnected. The XTAL1 input is a CMOS-type input, as required by the crystal oscillator. Publication Release Date: June 2000 Revision A1 -5- Preliminary W78LE516 Power Management Idle Mode Setting the IDL bit in the PCON register enters the idle mode. In the idle mode, the internal clock to the processor is stopped. The peripherals and the interrupt logic continue to be clocked. The processor will exit idle mode when either an interrupt or a reset occurs. Power-down Mode When the PD bit in the PCON register is set, the processor enters the power-down mode. In this mode all of the clocks are stopped, including the oscillator. To exit from power-down mode is by a hardware reset or external interrupts INT0 to INT1 when enabled and set to level triggered. Reduce EMI Emission The W78LE516 allows user to diminish the gain of on-chip oscillator amplifier by using programmer to clear the B7 bit of security register. Once B7 is set to 0, a half of gain will be decreased. Care must be taken if user attempts to diminish the gain of oscillator amplifier, reducing a half of gain may affect the external crystal operating improperly at high frequency. The value of C1 ana C2 may need some adjustment while running at lower gain. Reset The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to deglitch the reset line when the W78LE516 is used with an external RC network. The reset logic also has a special glitch removal circuit that ignores glitches on the reset line. During reset, the ports are initialized to FFH, the stack pointer to 07H, PCON (with the exception of bit 4) to 00H, and all of the other SFR registers except SBUF to 00H. SBUF is not reset. W78LE516 Special Function Registers (SFRs) and Reset Values F8 F0 E8 E0 D8 D0 C8 C0 B8 +ACC 00000000 +P4 xxxx1111 +PSW 00000000 +T2CON 00000000 XICON 00000000 +IP 00000000 RCAP2L 00000000 P4CONA 00000000 RCAP2H 00000000 P4CONB 00000000 TL2 00000000 SFRAL 00000000 TH2 00000000 SFRAH 00000000 SFRFD 00000000 SFRCN 00000000 CHPCON 0xx00000 +B 00000000 CHPENR 00000000 FF F7 EF E7 DF D7 CF C7 BF -6- Preliminary W78LE516 Continued B0 A8 A0 98 90 88 80 +P3 00000000 +IE 00000000 +P2 11111111 +SCON 00000000 +P1 11111111 +TCON 00000000 +P0 11111111 TMOD 00000000 SP 00000111 TL0 00000000 DPL 00000000 TL1 00000000 DPH 00000000 P43AL 00000000 P42AL 00000000 P43AH 00000000 P42AH 00000000 P2ECON 0000xx00 B7 AF A7 SBUF xxxxxxxx P41AL 00000000 TH0 00000000 P40AL 00000000 P41AH 00000000 TH1 00000000 P40AH 00000000 PCON 00110000 9F 97 8F 87 Notes: 1.The SFRs marked with a plus sign(+) are both byte- and bit-addressable. 2. The text of SFR with bold type characters are extension function registers. Port 4 Port 4, address D8H, is a 4-bit multipurpose programmable I/O port. Each bit can be configured individually by software. The Port 4 has four different operation modes. Mode 0: P4.0−P4.3 is a bi-directional I/O port which is same as port 1. P4.2 and P4.3 also serve as external interrupt CLR and INT2 if enabled. Mode 1: P4.0−P4.3 are read strobe signals that are synchronized with RD signal at specified addresses. These signals can be used as chip-select signals for external peripherals. Mode 2: P4.0−P4.3 are write strobe signals that are synchronized with WR signal at specified addresses. These signals can be used as chip-select signals for external peripherals. Mode 3: P4.0−P4.3 are read/write strobe signals that are synchronized with RD or WR signal at specified addresses. These signals can be used as chip-select signals for external peripherals. When Port 4 is configured with the feature of chip-select signals, the chip-select signal address range depends on the contents of the SFR P4xAH, P4xAL, P4CONA and P4CONB. The registers P4xAH and P4xAL contain the 16-bit base address of P4.x. The registers P4CONA and P4CONB contain the control bits to configure the Port 4 operation mode. INT2 / INT3 Two additional external interrupts, INT2 and INT3 , whose functions are similar to those of external interrupt 0 and 1 in the standard 80C52. The functions/status of these interrupts are determined/shown by the bits in the XICON (External Interrupt Control) register. The XICON register is bit-addressable but is not a standard register in the standard 80C52. Its address is at 0C0H. To set/clear bits in the XICON register, one can use the "SETB ( CLR ) bit" instruction. For example, "SETB 0C2H" sets the EX2 bit of XICON. -7- Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 XICON - external interrupt control (C0H) PX3 EX3 IE3 IT3 PX2 EX2 IE2 IT2 PX3:External interrupt 3 priority high if set EX3:External interrupt 3 enable if set IE3:If IT3 = 1, IE3 is set/cleared automatically by hardware when interrupt is detected/serviced IT3:External interrupt 3 is falling-edge/low-level triggered when this bit is set/cleared by software PX2:External interrupt 2 priority high if set EX2:External interrupt 2 enable if set IE2:If IT2 = 1, IE2 is set/cleared automatically by hardware when interrupt is detected/serviced IT2:External interrupt 2 is falling-edge/low-level triggered when this bit is set/cleared by software Eight-source interrupt information: INTERRUPT SOURCE External Interrupt 0 Timer/Counter 0 External Interrupt 1 Timer/Counter 1 Serial Port Timer/Counter 2 External Interrupt 2 External Interrupt 3 VECTOR ADDRESS 03H 0BH 13H 1BH 23H 2BH 33H 3BH POLLING SEQUENCE WITHIN PRIORITY LEVEL 0 (highest) 1 2 3 4 5 6 7 (lowest) ENABLE REQUIRED SETTINGS IE.0 IE.1 IE.2 IE.3 IE.4 IE.5 XICON.2 XICON.6 INTERRUPT TYPE EDGE/LEVEL TCON.0 TCON.2 XICON.0 XICON.3 P4CONB (C3H) BIT 7, 6 NAME FUNCTION P43FUN1 00: Mode 0. P4.3 is a general purpose I/O port which is the same as Port1. P43FUN0 01: Mode 1. P4.3 is a Read Strobe signal for chip select purpose. The address range depends on the SFR P43AH, P43AL, P43CMP1 and P43CMP0. 10: Mode 2. P4.3 is a Write Strobe signal for chip select purpose. The address range depends on the SFR P43AH, P43AL, P43CMP1 and P43CMP0. 11: Mode 3. P4.3 is a Read/Write Strobe signal for chip select purpose. The address range depends on the SFR P43AH, P43AL, P43CMP1, and P43CMP0. -8- Preliminary W78LE516 P4CONB (C3H), continued BIT 5, 4 NAME FUNCTION P43CMP1 Chip-select signals address comparison: P43CMP0 00: Compare the full address (16 bits length) with the base address register P43AH, P43AL. 01: Compare the 15 high bits (A15−A1) of address bus with the base address register P43AH, P43AL. 10: Compare the 14 high bits (A15−A2) of address bus with the base address register P43AH, P43AL. 11: Compare the 8 high bits (A15−A8) of address bus with the base address register P43AH, P43AL. P42FUN1 P42FUN0 P42CMP1 P42CMP0 The P4.2 function control bits which are the similar definition as P43FUN1, P43FUN0. The P4.2 address comparator length control bits which are the similar definition as P43CMP1, P43CMP0. 3, 2 1, 0 P4CONA (C2H) BIT 7, 6 5, 4 3, 2 1, 0 NAME P41FUN1 P41FUN0 P41CMP1 P41CMP0 P40FUN1 P40FUN0 P40CMP1 P40CMP0 FUNCTION The P4.1 function control bits which are the similar definition as P43FUN1, P43FUN0. The P4.1 address comparator length control bits which are the similar definition as P43CMP1, P43CMP0. The P4.0 function control bits which are the similar definition as P43FUN1, P43FUN0. The P4.0 address comparator length control bits which are the similar definition as P43CMP1, P43CMP0. P2ECON (AEH) BIT 7 NAME FUNCTION P43CSINV The active polarity of P4.3 when pin P4.3 is defined as read and/or write strobe signal. = 1 : P4.3 is active high when pin P4.3 is defined as read and/or write strobe signal. = 0 : P4.3 is active low when pin P4.3 is defined as read and/or write strobe signal. P42CSINV The similarity definition as P43SINV. P41CSINV The similarity definition as P43SINV. 6 5 -9- Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 P2ECON (AEH), continued BIT 5 4 3 2 1 0 NAME FUNCTION P41CSINV The similarity definition as P43SINV. P40CSINV The similarity definition as P43SINV. Reserve Reserve 0 0 Port 4 Base Address Registers P40AH, P40AL: The Base address register for comparator of P4.0. P40AH contains the high-order byte of address, P40AL contains the low-order byte of address. P41AH, P41AL: The Base address register for comparator of P4.1. P41AH contains the high-order byte of address, P41AL contains the low-order byte of address. P42AH, P42AL: The Base address register for comparator of P4.2. P42AH contains the high-order byte of address, P42AL contains the low-order byte of address. P43AH, P43AL: The Base address register for comparator of P4.3. P43AH contains the high-order byte of address, P43AL contains the low-order byte of address. P4 (D8H) BIT 7 6 5 4 3 2 1 0 NAME P43 P42 P41 P40 FUNCTION Reserve Reserve Reserve Reserve Port 4 Data bit which outputs to pin P4.3 at mode 0. Port 4 Data bit. which outputs to pin P4.2 at mode 0. Port 4 Data bit. which outputs to pin P4.1at mode 0. Port 4 Data bit which outputs to pin P4.0 at mode 0. - 10 - Preliminary W78LE516 Here is an example to program the P4.0 as a write strobe signal at the I/O port address 1234H−1237H and positive polarity, and P4.1−P4.3 are used as general I/O ports. MOV P40AH,#12H MOV P40AL,#34H MOV P4CONA,#00001010B MOV P4CONB,#00H MOV P2ECON,#10H MOV CHPENR,#00H ; Base I/O address 1234H for P4.0 ; P4.0 a write strobe signal and address line A0 and A1 are masked. ; P4.1−P4.3 as general I/O port which are the same as PORT1 ; Write the P40SINV = 1 to inverse the P4.0 write strobe polarity ; default is negative. ; Disable CHPCON write attribute. Then any instruction MOVX @DPTR,A (with DPTR = 1234H−1237H) will generate the positive polarity write strobe signal at pin P4.0. And the instruction MOV P4,#XX will output the bit3 to bit1 of data #XX to pin P4.3−P4.1. P4xCSINV P4 REGISTER P4.x DATA I/O RD_CS MUX 4->1 WR_CS READ WRITE RD/WR_CS PIN P4.x ADDRESS BUS EQUAL REGISTER P4xAL P4xAH P4xFUN0 P4xFUN1 Bit Length Selectable comparator REGISTER P4xCMP0 P4xCMP1 P4.x INPUT DATA BUS In-System Programming (ISP) Mode The W78LE516 equips one 64K byte of main MTP-ROM bank for application program (called APROM) and one 4K byte of auxiliary MTP-ROM bank for loader program (called LDROM). In the normal operation, the microcontroller executes the code in the APROM. If the content of APROM needs to be modified, the W78LE516 allows user to activate the In-System Programming (ISP) mode by setting the CHPCON register. The CHPCON is read-only by default, software must write two specific values 87H, then 59H sequentially to the CHPENR register to enable the CHPCON write attribute. Writing CHPENR register with the values except 87H and 59H will close CHPCON register write attribute. The W78LE516 achieves all in-system programming operations including enter/exit ISP Mode, program, erase, read ... etc, during device in the idle mode. Setting the Publication Release Date: June 2000 Revision A1 - 11 - Preliminary W78LE516 bit CHPCON.0 the device will enter in-system programming mode after a wake-up from idle mode. Because device needs proper time to complete the ISP operations before awaken from idle mode, software may use timer interrupt to control the duration for device wake-up from idle mode. To perform ISP operation for revising contents of APROM, software located at APROM setting the CHPCON register then enter idle mode, after awaken from idle mode the device executes the corresponding interrupt service routine in LDROM. Because the device will clear the program counter while switching from APROM to LDROM, the first execution of RETI instruction in interrupt service routine will jump to 00H at LDROM area. The device offers a software reset for switching back to APROM while the content of APROM has been updated completely. Setting CHPCON register bit 0, 1 and 7 to logic-1 will result a software reset to reset the CPU. The software reset serves as a external reset. This in-system programming feature makes the job easy and efficient in which the application needs to update firmware frequently. In some applications, the in-system programming feature make it possible to easily update the system firmware without opening the chassis. Note: The ISP Mode operates by supply voltage from 3.3V to 5.5V. SFRAH, SFRAL: The objective address of on-chip MTP-ROM in the in-system programming mode. SFRAH contains the high-order byte of address, SFRAL contains the low-order byte of address. SFRFD: The programming data for on-chip MTP-ROM in programming mode. SFRCN: The control byte of on-chip MTP-ROM programming mode. SFRCN (C7) BIT 7 6 NAME Reserve. = 0: 64K bytes MTP-ROM bank is selected as destination for reprogramming. = 1: 4K bytes MTP-ROM bank is selected as destination for re-programming. 5 4 OEN CEN MTP-ROM output enable. MTP-ROM chip enable. FUNCTION WFWIN On-chip MTP-ROM bank select for in-system programming. 3, 2, 1, 0 CTRL[3:0] The flash control signals MODE Erase 64KB APROM Program 64KB APROM Read 64KB APROM Erase 4KB LDROM Program 4KB LDROM Read 4KB LDROM WFWIN 0 0 0 1 1 1 CTRL 0010 0001 0000 0010 0001 0000 OEN 1 1 0 1 1 0 CEN 0 0 0 0 0 0 SFRAH, SFRAL X Address in Address in X Address in Address in SFRFD X Data in Data out X Data in Data out - 12 - Preliminary W78LE516 In-System Programming Control Register (CHPCON) CHPCON (BFH) BIT 7 NAME FUNCTION SWRESET When this bit is set to 1, and both FBOOTSL and FPROGEN are set to 1. It (F04KMODE) will enforce microcontroller reset to initial condition just like power on reset. This action will re-boot the microcontroller and start to normal operation. To read this bit in logic-1 can determine that the F04KBOOT mode is running. Reserve. Reserve. 0: Disable the on-chip AUX-RAM 6 5 4 3 2 1 ENAUXRAM 1: Enable on-chip AUX-RAM. 0 0 Must set to 0. Must set to 0. 0: The Loader Program locates at the 64 KB APROM. 4KB LDROM is destination for re-programming. 1: The Loader Program locates at the 4 KB memory bank. 64KB APROM is destination for re-programming. FBOOTSL The Program Location Select. 0 FPROGEN MTP-ROM Programming Enable. = 1: enable. The microcontroller enter the in-system programming mode after entering the idle mode and wake-up from interrupt. During in-system programming mode, the operation of erase, program and read are achieve when device enters idle mode. = 0: disable. The on-chip flash memory is read-only. In-system programmability is disabled. - 13 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 F04KBOOT Mode (Boot From LDROM) By default, the W78LE516 boots from APROM program after a power on reset. On some occasions, user can force the W78LE516 to boot from the LDROM program via following settings. The possible situation that you need to enter F04KBOOT mode when the APROM program can not run properly and device can not jump back to LDROM to execute in-system programming function. Then you can use this F04KBOOT mode to force the W78LE516 jumps to LDROM and executes in-system programming procedure. When you design your system, you may reserve the pins P2.6, P2.7 to switches or jumpers. For example in a CD-ROM system, you can connect the P2.6 and P2.7 to PLAY and EJECT buttons on the panel. When the APROM program fails to execute the normal application program. User can press both two buttons at the same time and then turn on the power of the personal computer to force the W78LE516 to enter the F04KBOOT mode. After power on of personal computer, you can release both buttons and finish the in-system programming procedure to update the APROM code. In application system design, user must take care of the P2, P3, ALE, EA and PSEN pin value at reset to prevent from accidentally activating the programming mode or F04KBOOT mode. F04KBOOT MODE P4.3 X L P2.7 L X P2.6 L X MODE FO4KBOOT FO4KBOOT The Reset Timing For Entering F04KBOOT Mode P2.7 Hi-Z P2.6 Hi-Z RST 30 mS 10 mS - 14 - Preliminary W78LE516 The Algorithm of In-System Programming Part 1:64KB APROM START procedure of entering In-System Programming Mode Enter In-System Programming Mode ? (conditions depend on user's application) Yes No Setting control registers MOV CHPENR,#87H MOV CHPENR,#59H MOV CHPCON,#03H Execute the normal application program Setting Timer (about 1.5 us) and enable timer interrupt END Start Timer and enter idle Mode. (CPU will be wakened from idle mode by timer interrupt, then enter In-System Programming mode) CPU will be wakened by interrupt and re-boot from 4KB LDROM to execute the loader program. Go - 15 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 Part 2: 4KB LDROM Go Procedure of Updating the 64KB APROM Timer Interrupt Service Routine: Stop Timer & disable interrupt PGM Yes Is F04KBOOT Mode? (CHPCON.7=1) No Reset the CHPCON Register: MOV CHPENR,#87H MOV CHPENR,#59H MOV CHPCON,#03H Setting Timer and enable Timer interrupt for wake-up . (50us for program operation) End of Programming ? Yes No Is currently in the F04KBOOT Mode ? No Software reset CPU and re-boot from the 64KB APROM. MOV CHPENR,#87H MOV CHPENR,#59H MOV CHPCON,#83H Yes Get the parameters of new code Setting Timer and enable Timer interrupt for wake-up . (15 ms for erasing operation) (Address and data bytes) through I/O ports, UART or other interfaces. Setting erase operation mode: MOV SFRCN,#22H (Erase 64KB APROM) Setting control registers for programming: MOV SFRAH,#ADDRESS_H MOV SFRAL,#ADDRESS_L MOV SFRFD,#DATA MOV SFRCN,#21H Start Timer and enter IDLE Mode. (Erasing...) Hardware Reset to re-boot from new 64 KB APROM. (S/W reset is invalid in F04KBOOT Mode) End of erase operation. CPU will be wakened by Timer interrupt. END Executing new code from address 00H in the 64KB APROM. PGM - 16 - Preliminary W78LE516 SECURITY During the on-chip MTP-ROM programming mode, the MTP-ROM can be programmed and verified repeatedly. Until the code inside the MTP-ROM is confirmed OK, the code can be protected. The protection of MTP-ROM and those operations on it are described below. The W78LE516 has several Special Setting Registers, including the Security Register and Company/Device ID Registers, which can not be accessed in programming mode. Those bits of the Security Registers can not be changed once they have been programmed from high to low. They can only be reset through erase-all operation. The contents of the Company ID and Device ID registers have been set in factory. The Security Register is located at the 0FFFFH of the LDROM space. D7 D6 D5 D4 D3 D2 D1 D0 11011010 01100010 B7 Reserved B2 B1 B0 Company ID (#DAH) Device ID (#62H) Security Bits 0000h 4KB MTP ROM Program Memory LDROM 0FFFh 64KB MTP ROM Program Memory APROM B0: Lock bit, logic 0: active B1: MOVC inhibit, logic 0: the MOVC instruction in external memory cannot access the code in internal memory. logic 1: no restriction. B2: Encryption logic 0: the encryption logic enable logic 1: the encryption logic disable B07: Osillator Control logic 0: 1/2 gain logic 1: Full gain Default 1 for all security bits. Reserved bits must be kept in logic 1. Reserved Reserved Security Register FFFFh Special Setting Registers Lock bit This bit is used to protect the customer's program code in the W78LE516. It may be set after the programmer finishes the programming and verifies sequence. Once this bit is set to logic 0, both the MTP ROM data and Special Setting Registers can? be accessed again. MOVC Inhibit This bit is used to restrict the accessible region of the MOVC instruction. It can prevent the MOVC instruction in external program memory from reading the internal program code. When this bit is set to logic 0, a MOVC instruction in external program memory space will be able to access code only in the external memory, not in the internal memory. A MOVC instruction in internal program memory space will always be able to access the ROM data in both internal and external memory. If this bit is logic 1, there are no restrictions on the MOVC instruction. Encryption This bit is used to enable/disable the encryption logic for code protection. Once encryption feature is enabled, the data presented on port 0 will be encoded via encryption logic. Only whole chip erase will reset this bit. Publication Release Date: June 2000 Revision A1 - 17 - Preliminary W78LE516 Oscillator Control W78LE516/E516 allow user to diminish the gain of on-chip oscillator amplifier by using programmer to set the bit B7 of security register. Once B7 is set to 0, a half of gain will be decreased. Care must be taken if user attempts to diminish the gain of oscillator amplifier, reducing a half of gain may improperly affect the external crystal operation at high frequency. The value of C1 and C2 may need some adjustment while running at lower gain. ABSOLUTE MAXIMUM RATINGS PARAMETER DC Power Supply Input Voltage Operating Temperature Storage Temperature SYMBOL VDD−VSS VIN TA TST MIN. -0.3 VSS -0.3 0 -55 MAX. +6.0 VDD +0.3 60 +150 UNIT V V °C °C Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. DC CHARACTERISTICS VSS = 0V, TA = 25° C, unless otherwise specified. PARAMETER Operating Voltage Operating Current Idle Current Power Down Current Input Current P1, P2, P3, P4 Input Current RST Input Leakage Current P0, EA Logic 1 to 0 Transition Current P1, P2, P3, P4 Input Low Voltage P0, P1, P2, P3, P4, EA Input Low Voltage RST[*1] SYM. VDD IDD IIDLE IPWDN IIN1 IIN2 ILK ITL [*4] SPECIFICATION MIN. MAX. 2.4 5.5 3.3 5.5 20 3 6 1.5 50 20 -50 +10 -10 -10 -500 +300 +10 - UNIT V V mA mA mA mA µA µA µA µA µA µA TEST CONDITIONS Without I.S.P. With I.S.P. No load VDD = 5.5V No load VDD = 2.4V VDD = 5.5V, Fosc = 20 MHz VDD = 2.4V, Fosc = 12 MHz VDD = 5.5V, Fosc = 20 MHz VDD = 2.4V, Fosc = 12 MHz VDD = 5.5V VIN = 0V or VDD VDD = 5.5V 0 < VIN < VDD VDD = 5.5V 0V < VIN < VDD VDD = 5.5V VIN = 2.0V VDD = 4.5V VDD = 2.4V VDD = 4.5V VDD = 2.4V VIL1 VIL2 0 0 0 0 0.8 0.5 0.8 0.3 V V V V - 18 - Preliminary W78LE516 DC Characteristics, continued PARAMETER SYM. SPECIFICATION MIN. MAX. 0.8 0.4 VDD +0.2 VDD +0.2 VDD +0.2 VDD +0.2 VDD +0.2 VDD +0.2 0.45 0.25 0.45 0.25 12 5.4 16 9 -250 -50 -14 -3.8 UNIT TEST CONDITIONS Input Low Voltage XTAL1 [*3] Input High Voltage P0, P1, P2, P3, P4, EA Input High Voltage RST[*1] Input High Voltage XTAL1 [*3] Output Low Voltage P1, P2, P3, P4 Output Low Voltage P0, ALE, PSEN [*2] Sink Current P1, P2, P3, P4 Sink Current P0, ALE, PSEN Output High Voltage P1, P2, P3, P4 Output High Voltage P0, ALE, PSEN [*2] Source Current P1, P2, P3, P4 Source Current P0, ALE, PSEN Notes: *1. RST pin is a Schmitt trigger input. VIL3 VIH1 0 0 2.4 1.4 V V V V V V V V V V V V mA mA mA mA V V V V µA µA mA mA VDD = 4.5V VDD = 2.4V VDD = 5.5V VDD = 2.4V VDD = 5.5V VDD = 2.4V VDD = 5.5V VDD = 2.4V VDD = 4.5V, IOL = +2 mA VDD = 2.4V, IOL = +1 mA VDD = 4.5V, IOL = +4 mA VDD = 2.4V, IOL = +2 mA VDD = 4.5V, Vin = 0.45V VDD = 2.4V, Vin = 0.45V VDD = 4.5V, Vin = 0.45V VDD = 2.4V, Vin = 0.4V VDD = 4.5V, IOH = -100 µA VDD = 2.4V, IOH = -8 µA VDD = 4.5V, IOH = -400 µA VDD = 2.4V, IOH = -200 µA VDD = 4.5V, Vin = 2.4V VDD = 2.4V, Vin = 1.4V VDD = 4.5V, Vin = 2.4V VDD = 2.4V, Vin = 1.4V VIH2 3.5 1.7 VIH3 VOL1 VOL2 3.5 2.4 - ISK1 ISK2 4 1.8 8 4.5 VOH1 2.4 1.4 VOH2 2.4 1.4 ISR1 -100 -20 ISR2 -8 -1.9 *2. P0, ALE and PSEN are tested in the external access mode. *3. XTAL1 is a CMOS input. *4. Pins of P1, P2, P3, P4 can source a transition current when they are being externally driven from 1 to 0. - 19 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 AC CHARACTERISTICS The AC specifications are a function of the particular process used to manufacture the part, the ratings of the I/O buffers, the capacitive load, and the internal routing capacitance. Most of the specifications can be expressed in terms of multiple input clock periods (TCP), and actual parts will usually experience less than a ±20 nS variation. The numbers below represent the performance expected from a 0.6 micron CMOS process when using 2 and 4 mA output buffers. Clock Input Waveform XTAL1 T CH F OP, TCP T CL PARAMETER Operating Speed Clock Period Clock High Clock Low SYMBOL FOP TCP TCH TCL MIN. 0 25 10 10 TYP. - MAX. 24 - UNIT MHz nS nS nS NOTES 1 2 3 3 Notes: 1. The clock may be stopped indefinitely in either state. 2. The TCP specification is used as a reference in other specifications. 3. There are no duty cycle requirements on the XTAL1 input. Program Fetch Cycle PARAMETER Address Valid to ALE Low Address Hold from ALE Low ALE Low to PSEN Low SYMBOL TAAS TAAH TAPL TPDA TPDH TPDZ TALW TPSW MIN. 1 TCP-∆ 1 TCP-∆ 1 TCP-∆ 0 0 2 TCP-∆ 3 TCP-∆ TYP. 2 TCP 3 TCP MAX. 2 TCP 1 TCP 1 TCP UNIT nS nS nS nS nS nS nS nS 4 4 NOTES 4 1, 4 4 2 3 PSEN Low to Data Valid Data Hold after PSEN High Data Float after PSEN High ALE Pulse Width PSEN Pulse Width Notes: 1. P0.0−P0.7, P2.0−P2.7 remain stable throughout entire memory cycle. 2. Memory access time is 3 TCP. 3. Data have been latched internally prior to PSEN going high. 4. "∆" (due to buffer driving delay and wire loading) is 20 nS. - 20 - Preliminary W78LE516 Data Read Cycle PARAMETER ALE Low to RD Low RD Low to Data Valid Data Hold from RD High Data Float from RD High RD Pulse Width SYMBOL TDAR TDDA TDDH TDDZ TDRD MIN. 3 TCP-∆ 0 0 6 TCP-∆ TYP. 6 TCP MAX. 3 TCP+∆ 4 TCP 2 TCP 2 TCP UNIT nS nS nS nS nS 2 NOTES 1, 2 1 Notes: 1. Data memory access time is 8 TCP. 2. "∆" (due to buffer driving delay and wire loading) is 20 nS. Data Write Cycle PARAMETER ALE Low to WR Low Data Valid to WR Low Data Hold from WR High WR Pulse Width SYMBOL TDAW TDAD TDWD TDWR MIN. 3 TCP-∆ 1 TCP-∆ 1 TCP-∆ 6 TCP-∆ TYP. 6 TCP MAX. 3 TCP+∆ - UNIT nS nS nS nS Note: "∆" (due to buffer driving delay and wire loading) is 20 nS. Port Access Cycle PARAMETER Port Input Setup to ALE Low Port Input Hold from ALE Low Port Output to ALE SYMBOL TPDS TPDH TPDA MIN. 1 TCP 0 1 TCP TYP. MAX. UNIT nS nS nS Note: Ports are read during S5P2, and output data becomes available at the end of S6P2. The timing data are referenced to ALE, since it provides a convenient reference. - 21 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 TIMING WAVEFORMS Program Fetch Cycle S1 XTAL1 S2 S3 S4 S5 S6 S1 S2 S3 S4 S5 S6 TALW ALE TAPL PSEN TPSW TAAS PORT 2 TAAH PORT 0 Code A0-A7 Data A0-A7 Code A0-A7 Data A0-A7 TPDA TPDH, TPDZ Data Read Cycle S4 XTAL1 ALE PSEN PORT 2 S5 S6 S1 S2 S3 S4 S5 S6 S1 S2 S3 A8-A15 A0-A7 DATA T DAR T DDA PORT 0 T DDH, T DDZ RD TDRD - 22 - Preliminary W78LE516 Timing Waveforms, continued Data Write Cycle S4 XTAL1 ALE PSEN PORT 2 PORT 0 WR S5 S6 S1 S2 S3 S4 S5 S6 S1 S2 S3 A8-A15 A0-A7 DATA OUT TDAD T DWD TDAW T DWR Port Access Cycle S5 XTAL1 S6 S1 ALE TPDS PORT INPUT SAMPLE TPDH T PDA DATA OUT - 23 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 TYPICAL APPLICATION CIRCUIT Expanded External Program Memory and Crystal V DD 31 19 10 u R CRYSTAL EA XTAL1 XTAL2 RST INT0 INT1 T0 T1 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 W78LE516 18 9 8.2 K C1 C2 P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 RD WR PSEN ALE TXD RXD 39 AD0 38 AD1 37 AD2 36 AD3 35 AD4 34 AD5 33 AD6 32 AD7 21 22 23 24 25 26 27 28 17 16 29 30 11 10 A8 A9 A10 A11 A12 A13 A14 A15 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND 3 4 7 8 13 14 17 18 1 11 D0 D1 D2 D3 D4 D5 D6 D7 OC G Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 2 5 6 9 12 15 16 19 A0 A1 A2 A3 A4 A5 A6 A7 12 13 14 15 1 2 3 4 5 6 7 8 74LS373 A0 10 A1 9 A2 8 A3 7 A4 6 A5 5 A6 4 A7 3 A8 25 A9 24 A10 21 A11 23 A12 2 A13 26 A14 27 A15 1 GND 20 22 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 CE OE 27512 O0 O1 O2 O3 O4 O5 O6 O7 11 12 13 15 16 17 18 19 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 Figure A CRYSTAL 6 MHz 16 MHz 24 MHz C1 47P 30P 15P C2 47P 30P 10P R - Above table shows the reference values for crystal applications. Notes: 1. C1, C2, R components refer to Figure A 2. Crystal layout must get close to XTAL1 and XTAL2 pins on user's application board. - 24 - Preliminary W78LE516 Tipical Application Circuit, continued Expanded External Data Memory and Oscillator VDD V DD 31 19 10 u OSCILLATOR 18 8.2 K 9 12 13 14 15 1 2 3 4 5 6 7 8 EA XTAL1 XTAL2 RST INT0 INT1 T0 T1 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 W78LE516 P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 RD WR PSEN ALE TXD RXD 39 38 37 36 35 34 33 32 21 22 23 24 25 26 27 28 17 16 29 30 11 10 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 A8 A9 A10 A11 A12 A13 A14 AD0 3 AD1 4 AD2 7 AD3 8 AD4 13 AD5 14 AD6 17 AD7 18 GND 1 11 D0 D1 D2 D3 D4 D5 D6 D7 OC G 74LS373 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 2 5 6 9 12 15 16 19 A0 A1 A2 A3 A4 A5 A6 A7 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 GND 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1 20 22 27 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 CE OE WR 20256 D0 D1 D2 D3 D4 D5 D6 D7 11 12 13 15 16 17 18 19 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 Figure B PACKAGE DIMENSIONS 40-pin DIP Dimension in inch Dimension in mm Min. Nom. Max. Min. Nom. Max. 0.210 0.010 0.150 0.016 0.048 0.008 0.155 0.018 0.050 0.010 2.055 0.590 0.540 0.090 0.120 0 0.630 0.650 0.600 0.545 0.100 0.130 0.160 0.022 0.054 0.014 2.070 0.610 14.986 0.550 0.110 0.140 15 0.670 0.090 13.72 2.286 3.048 0 16.00 16.51 0.254 3.81 0.406 1.219 0.203 3.937 0.457 1.27 0.254 52.20 15.24 13.84 2.54 3.302 4.064 0.559 1.372 0.356 52.58 15.494 13.97 2.794 3.556 15 17.01 2.286 5.334 Symbol D 40 21 E1 A A1 A2 B B1 c D E E1 e1 L a 1 S 20 E c eA S Notes: A A2 A1 Base Plane Seating Plane L B B1 e1 a eA 1. Dimension D Max. & S include mold flash or tie bar burrs. 2. Dimension E1 does not include interlead flash. 3. Dimension D & E1 include mold mismatch and . are determined at the mold parting line. 4. Dimension B1 does not include dambar protrusion/intrusion. 5. Controlling dimension: Inches. 6. General appearance spec. should be based on final visual inspection spec. - 25 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 Package Dimensions, continued 44-pin PLCC HD D 6 1 44 40 Symbol 7 39 Dimension in inch Dimension in mm Min. Nom. Max. Min. Nom. Max. 0.185 0.020 0.145 0.026 0.016 0.008 0.648 0.648 0.150 0.028 0.018 0.010 0.653 0.653 0.155 0.032 0.022 0.014 0.658 0.658 0.508 3.683 0.66 0.406 0.203 16.46 16.46 3.81 0.711 0.457 0.254 16.59 16.59 3.937 0.813 0.559 0.356 16.71 16.71 4.699 E HE GE 17 29 18 28 c A A1 A2 b1 b c D E e GD GE HD HE L y Notes: 0.050 0.590 0.590 0.680 0.680 0.090 BSC 0.630 0.630 0.700 0.700 0.110 0.004 1.27 14.99 14.99 17.27 17.27 2.296 BSC 16.00 16.00 17.78 17.78 2.794 0.10 0.610 0.610 0.690 0.690 0.100 15.49 15.49 17.53 17.53 2.54 L A2 A θ e Seating Plane GD b b1 A1 y 1. Dimension D & E do not include interlead flash. 2. Dimension b1 does not include dambar protrusion/intrusion. 3. Controlling dimension: Inches 4. General appearance spec. should be based on final visual inspection spec. 44-pin PQFP HD D Dimension in inch Dimension in mm Symbol 44 34 Min. Nom. --0.002 0.075 0.01 0.004 0.390 0.390 0.025 0.510 0.510 0.025 0.051 --0.01 0.081 0.014 0.006 0.394 0.394 0.031 0.520 0.520 0.031 0.063 Max. --0.02 0.087 0.018 0.010 0.398 0.398 0.036 0.530 0.530 0.037 0.075 0.003 Min. Nom. --0.05 1.90 0.25 0.101 9.9 9.9 0.635 12.95 12.95 0.65 1.295 --0.25 2.05 0.35 0.152 10.00 10.00 0.80 13.2 13.2 0.8 1.6 Max. --0.5 2.20 0.45 0.254 10.1 10.1 0.952 13.45 13.45 0.95 1.905 0.08 1 33 E HE 11 12 e b 22 A A1 A2 b c D E e HD HE L L1 y θ Notes: c 0 7 0 7 A2 A1 A θ L L 1 Seating Plane See Detail F y 1. Dimension D & E do not include interlead flash. 2. Dimension b does not include dambar protrusion/intrusion. 3. Controlling dimension: Millimeter 4. General appearance spec. should be based on final visual inspection spec. Detail F - 26 - Preliminary W78LE516 Application Note: In-system Programming Software Examples This application note illustrates the in-system programmability of the Winbond W78LE516 MTP-ROM microcontroller. In this example, microcontroller will boot from 64 KB APROM bank and waiting for a key to enter in-system programming mode for re-programming the contents of 64 KB APROM. While entering in-system programming mode, microcontroller executes the loader program in 4KB LDROM bank. The loader program erases the 64 KB APROM then reads the new code data from external SRAM buffer (or through other interfaces) to update the 64KB APROM. EXAMPLE 1: ;******************************************************************************************************************* ;* Example of 64K APROM program: Program will scan the P1.0. if P1.0 = 0, enters in-system ;* programming mode for updating the content of APROM code else executes the current ROM code. ;* XTAL = 16 MHz ;******************************************************************************************************************* .chip 8052 .RAMCHK OFF .symbols CHPCON CHPENR SFRAL SFRAH SFRFD SFRCN EQU EQU EQU EQU EQU EQU BFH F6H C4H C5H C6H C7H ORG 0H LJMP 100H ; JUMP TO MAIN PROGRAM ;************************************************************************ ;* TIMER0 SERVICE VECTOR ORG = 000BH ;************************************************************************ ORG 00BH CLR TR0 ; TR0 = 0, STOP TIMER0 MOV TL0,R6 MOV TH0,R7 RETI ;************************************************************************ ;* 64K APROM MAIN PROGRAM ;************************************************************************ ORG 100H MAIN_64K: MOV A,P1 ; SCAN P1.0 ANL A,#01H CJNE A,#01H,PROGRAM_64K ; IF P1.0 = 0, ENTER IN-SYSTEM PROGRAMMING MODE JMP NORMAL_MODE PROGRAM_64K: MOV CHPENR,#87H MOV CHPENR,#59H MOV CHPCON,#03H MOV TCON,#00H MOV IP,#00H ; CHPENR = 87H, CHPCON REGISTER WRTE ENABLE ; CHPENR = 59H, CHPCON REGISTER WRITE ENABLE ; CHPCON = 03H, ENTER IN-SYSTEM PROGRAMMING MODE ; TR = 0 TIMER0 STOP ; IP = 00H - 27 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 MOV IE,#82H MOV R6,#FEH MOV R7,#FFH MOV TL0,R6 MOV TH0,R7 MOV TMOD,#01H MOV TCON,#10H MOV PCON,#01H ; TIMER0 INTERRUPT ENABLE FOR WAKE-UP FROM IDLE MODE ; TL0 = FEH ; TH0 = FFH ; TMOD = 01H, SET TIMER0 A 16-BIT TIMER ; TCON = 10H, TR0 = 1,GO ; ENTER IDLE MODE FOR LAUNCHING THE IN-SYSTEM ; PROGRAMMING ;******************************************************************************** ;* Normal mode 64KB APROM program: depending user's application ;******************************************************************************** NORMAL_MODE: . . . . ; User's application program EXAMPLE 2: ;***************************************************************************************************************************** ;* Example of 4 KB LDROM program: This loader program will erase the 64KB APROM first, then reads the new ;* code from external SRAM and program them into 64 KB APROM bank. XTAL = 16 MHz ;***************************************************************************************************************************** .chip 8052 .RAMCHK OFF .symbols CHPCON CHPENR SFRAL SFRAH SFRFD SFRCN EQU EQU EQU EQU EQU EQU BFH F6H C4H C5H C6H C7H ORG 000H LJMP 100H ; JUMP TO MAIN PROGRAM ;************************************************************************ ;* 1. TIMER0 SERVICE VECTOR ORG = 0BH ;************************************************************************ ORG 000BH CLR TR0 ; TR0 = 0, STOP TIMER0 MOV TL0,R6 MOV TH0,R7 RETI ;************************************************************************ ;* 4KB LDROM MAIN PROGRAM ;************************************************************************ ORG 100H - 28 - Preliminary W78LE516 MAIN_4K: MOV CHPENR,#87H ; CHPENR = 87H, CHPCON WRITE ENABLE. MOV CHPENR,#59H ; CHPENR = 59H, CHPCON WRITE ENABLE. MOV A,CHPCON ANL A,#80H CJNE A,#80H,UPDATE_64K ; CHECK F04KBOOT MODE ? MOV CHPCON,#03H MOV CHPENR,#00H MOV TCON,#00H MOV TMOD,#01H MOV IP,#00H MOV IE,#82H MOV R6,#FEH MOV R7,#FFH MOV TL0,R6 MOV TH0,R7 MOV TCON,#10H MOV PCON,#01H UPDATE_64K: MOV CHPENR,#00H MOV TCON,#00H MOV IP,#00H MOV IE,#82H MOV TMOD,#01H MOV R6,#E0H DEPENDING MOV R7,#B1H MOV TL0,R6 MOV TH0,R7 ERASE_P_4K: MOV SFRCN,#22H MOV TCON,#10H MOV PCON,#01H ; SFRCN(C7H) = 22H ERASE 64K ; TCON = 10H, TR0 = 1,GO ; ENTER IDLE MODE (FOR ERASE OPERATION) ; CHPCON = 03H, ENABLE IN-SYSTEM PROGRAMMING. ; DISABLE CHPCON WRITE ATTRIBUTE ; TCON = 00H, TR = 0 TIMER0 STOP ; TMOD = 01H, SET TIMER0 A 16BIT TIMER ; IP = 00H ; IE = 82H, TIMER0 INTERRUPT ENABLED ; TCON = 10H, TR0 = 1, GO ; ENTER IDLE MODE ; DISABLE CHPCON WRITE-ATTRIBUTE ; TCON = 00H , TR = 0 TIM0 STOP ; IP = 00H ; IE = 82H, TIMER0 INTERRUPT ENABLED ; TMOD = 01H, MODE1 ; SET WAKE-UP TIME FOR ERASE OPERATION, ABOUT 15 mS. ; ON USER'S SYSTEM CLOCK RATE. ;********************************************************************* ;* BLANK CHECK ;********************************************************************* MOV SFRCN,#0H ; READ 64KB APROM MODE MOV SFRAH,#0H ; START ADDRESS = 0H MOV SFRAL,#0H MOV R6,#FEH ; SET TIMER FOR READ OPERATION, ABOUT 1.5 µS. MOV R7,#FFH MOV TL0,R6 MOV TH0,R7 BLANK_CHECK_LOOP: SETB TR0 MOV PCON,#01H ; ENABLE TIMER 0 ; ENTER IDLE MODE - 29 - Publication Release Date: June 2000 Revision A1 Preliminary W78LE516 MOV A,SFRFD ; READ ONE BYTE CJNE A,#FFH,BLANK_CHECK_ERROR INC SFRAL ; NEXT ADDRESS MOV A,SFRAL JNZ BLANK_CHECK_LOOP INC SFRAH MOV A,SFRAH CJNE A,#0H,BLANK_CHECK_LOOP ; END ADDRESS = FFFFH JMP PROGRAM_64KROM BLANK_CHECK_ERROR: MOV P1,#F0H MOV P3,#F0H JMP $ ;******************************************************************************* ;* RE-PROGRAMMING 64KB APROM BANK ;******************************************************************************* PROGRAM_64KROM: MOV DPTR,#0H MOV R2,#00H MOV R1,#00H MOV DPTR,#0H MOV SFRAH,R1 MOV SFRCN,#21H MOV R6,#BEH MOV R7,#FFH MOV TL0,R6 MOV TH0,R7 PROG_D_64K: MOV SFRAL,R2 MOVX A,@DPTR ; SFRAL(C4H) = LOW BYTE ADDRESS ; READ DATA FROM EXTERNAL SRAM BUFFER. BY ACCORDING USER? ; CIRCUIT, USER MUST MODIFY THIS INSTRUCTION TO FETCH CODE. ; SFRFD(C6H) = DATA IN ; TCON = 10H, TR0 = 1,GO ; ENTER IDLE MODE (PRORGAMMING) ; THE ADDRESS OF NEW ROM CODE ; TARGET LOW BYTE ADDRESS ; TARGET HIGH BYTE ADDRESS ; EXTERNAL SRAM BUFFER ADDRESS ; SFRAH, TARGET HIGH ADDRESS ; SFRCN(C7H) = 21 (PROGRAM 64K) ; SET TIMER FOR PROGRAMMING, ABOUT 50 µS. MOV SFRFD,A MOV TCON,#10H MOV PCON,#01H INC DPTR INC R2 CJNE R2,#0H,PROG_D_64K INC R1 MOV SFRAH,R1 CJNE R1,#0H,PROG_D_64K ;***************************************************************************** ; * VERIFY 64KB APROM BANK ;***************************************************************************** MOV R4,#03H ; ERROR COUNTER MOV R6,#FEH ; SET TIMER FOR READ VERIFY, ABOUT 1.5 µS. MOV R7,#FFH MOV TL0,R6 MOV TH0,R7 MOV DPTR,#0H ; The start address of sample code MOV R2,#0H ; Target low byte address - 30 - Preliminary W78LE516 MOV R1,#0H MOV SFRAH,R1 MOV SFRCN,#00H READ_VERIFY_64K: MOV SFRAL,R2 ; SFRAL(C4H) = LOW ADDRESS MOV TCON,#10H ; TCON = 10H, TR0 = 1,GO MOV PCON,#01H INC R2 MOVX A,@DPTR INC DPTR CJNE A,SFRFD,ERROR_64K CJNE R2,#0H,READ_VERIFY_64K INC R1 MOV SFRAH,R1 CJNE R1,#0H,READ_VERIFY_64K ;****************************************************************************** ;* PROGRAMMING COMPLETLY, SOFTWARE RESET CPU ;****************************************************************************** MOV CHPENR,#87H ; CHPENR = 87H MOV CHPENR,#59H ; CHPENR = 59H MOV CHPCON,#83H ; CHPCON = 83H, SOFTWARE RESET. ERROR_64K: DJNZ R4,UPDATE_64K . . . . ; IF ERROR OCCURS, REPEAT 3 TIMES. ; IN-SYSTEM PROGRAMMING FAIL, USER'S PROCESS TO DEAL WITH IT. ; Target high byte address ; SFRAH, Target high address ; SFRCN = 00 (Read Flash code) Headquarters Headquarters Winbond Electronics (H.K.) Ltd. Unit 9 -15, 22F, Millennium City, No. 4, Creation Rd. III, No. 378 Kwun Tong Rd; Science -Based Industrial Park, Kowloon, Hong Kong Hsinchu, Taiwan TEL: 852 -27513100 TEL: 886 -3-5770066 FAX: 852 -27552064 FAX: 886 -3-5792766 http://www.winbond.com.tw/ Voice & Fax -on-demand: 886 -2-27197006 Winbond Electronics North America Corp. Winbond Memory Lab. Winbond Microelectronics Corp. Winbond Systems Lab. 2727 N. First Street, San Jose, CA 95134, U.S.A. TEL: 408 -9436666 FAX: 408 -5441798 Taipei Office 11F, No. 115, Sec. 3, Min -Sheng East Rd., Taipei, Taiwan TEL: 886 -2-27190505 FAX: 886 -2-27197502 Note: All data and specifications are subject to change withou t notice. - 31 - Publication Release Date: June 2000 Revision A1