W83195AR-25

W83195AR-25 200MHZ 3-DIMM CLOCK FOR SOLANO CHIPSET 1.0 GENERAL DESCRIPTION The W83195AR-25 is a Clock Synthesizer for Intel 815 Solano chipset. W83195AR-25 provides all clocks required for high-speed RISC or CISC microprocessor and also provides 64 different frequencies of CPU, SDRAM, PCI, 3V66, IOAPIC clocks frequency setting. All clocks are externally selectable with smooth transitions. The W83195AR-25 provides I2C serial bus interface to program the registers to enable or disable each clock outputs and provides 0.25% and 0.5% center type spread spectrum to reduce EMI. The W83195AR-25 accepts a 14.318 MHz reference crystal as its input and runs on a 3.3V supply. High drive PCI and SDRAM CLOCK outputs typically provide greater than 1 V /ns slew rate into 30 pF loads. CPU CLOCK outputs typically provide better than 1 V /ns slew rate into 20 pF loads as maintaining 50± 5% duty cycle. The fixed frequency outputs as REF, 24MHz, and 48 MHz provide better than 0.5V /ns slew rate. 2.0 PRODUCT FEATURES • • • • • • • • • • • • • 2 CPU clocks (2.5V) 3 3V-66 clocks (3.3V) 12 SDRAM clocks for 3 DIMMs(3.3V) 8 PCI synchronous clocks. Optional single or mixed supply: (VDDR = VDDP=VDDS = VDD48 = VDD3 = 3.3V, VDDA=VDDC=2.5V) Skew form CPU to PCI clock -1 to 4 ns, center 2.6 ns Smooth frequency switch with selections from 66.8 to 200MHz I2C 2-Wire serial interface and I2C read back 0.25% center and 0.5% center type spread spectrum Programmable registers to enable/stop each output and select modes (mode as Tri-state or Normal ) 48 MHz for USB 24 MHz for super I/O Packaged in 56-pin SSOP -1- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 3.0 PIN CONFIGURATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 REF0/ *FS4^ VddA IOAPIC VDDC CPUCLK0 CPUCLK1 VSS VSS SDRAM 0 SDRAM 1 SDRAM 2 VDDS SDRAM 3 SDRAM 4 SDRAM 5 VSS SDRAM 6 SDRAM 7 SDRAM_F VDDS VSS 24_48MHz/ *FS2 48MHz/ *FS3 ^ VDD48 VDDS SDRAM 8 SDRAM 9 VSS VDDR Xin Xout VSS VSS 3V66-0 3V66-1 3V66-2 VDD3 VDDP PCICLK0/ *FS0 PCICLK1/ *FS1 PCICLK2/SEL24_48* VSS PCICLK3^ PCICLK4^ PCICLK5^ VDDP PCICLK6 PCICLK7 VSS PD# *SDCLK *SDATA VDDS SDRAM 11 SDRAM 10 VSS 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 Note: * Internal pull-up ^ 1.5~2 strength -2- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 4.0 PIN DESCRIPTION IN - Input OUT - Output I/O - Bi-directional Pin # - Active Low * - Internal 250kΩ pull-up 4.1 Crystal I/O SYMBOL Xin Xout PIN 2 3 I/O IN OUT FUNCTION Crystal input with internal loading capacitors(36pF) and feedback resistors. Crystal output at 14.318MHz nominally with internal loading capacitors(36pF). 4.2 CPU, SDRAM, PCI, IOAPIC Clock Outputs SYMBOL CPUCLK [0:1] PD# IOAPIC SDRAM_F, SDRAM[0:11] PIN 52,51 22 54 38, 48,47,46, 44,43,42,40, 39,31, 30,27, 26 11 I/O OUT IN OUT OUT FUNCTION Low skew (< 250ps) clock outputs for host frequencies such as CPU and Chipset. Power Down mode when driven low. Clock outputs synchronous with PCI clock and powered by VddA. SDRAM clock outputs. PCICLK0/ *FS0 I/O PCICLK1/ FS1# 12 I/O PCICLK2/ *SEL24_48 12 I/O 3.3V 33MHz PCI clock during normal operation. Latched input for FS0 at initial power up for H/W selecting the output frequency of CPU, SDRAM and PCI clocks(Default=1). Low skew (< 250ps) PCI clock outputs. Latched input for FS1 at initial power up for H/W selecting the output frequency of CPU, SDRAM and PCI clocks(Default=0). Low skew (< 250ps) PCI clock outputs. Latched input for SEL24_48 at initial power up for the output frequency of 24MHz(HIGH) and 48MHz(LOW) clocks. Low skew (< 250ps) PCI clock outputs. 3.3V output clocks for the chipset. PCICLK [ 3:7 ] 3V66 [0:2] 15,16,17,19,20 6,7,8 OUT OUT -3- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 4.3 I2C Control Interface SYMBOL *SDATA *SDCLK PIN 24 23 I/O I/O IN 2 FUNCTION Serial data of I C 2-wire control interface with internal pull-up resistor. Serial clock of I2C 2-wire control interface with internal pull-up resistor. 4.4 Fixed Frequency Outputs SYMBOL REF0 / *FS4 PIN 56 I/O I/O FUNCTION 14.318MHz reference clock. This REF output is the stronger buffer for ISA bus loads. Latched input for FS4 at initial power up for H/W selecting the output frequency of CPU, SDRAM and PCI clocks (Default=1). 24_48MHz/FS2* 23 I/O 24MHz or 48MHz output clock. Default is 24MHz. Latched input for FS2 at initial power up for H/W selecting the output frequency of CPU, SDRAM and PCI clocks(Default=1). 48MHz/ FS3* 22 I/O 48MHz / Latched input for FS3 at initial power up for H/W selecting the output frequency of CPU, SDRAM and PCI clocks (Default=1). 4.5 Power Pins SYMBOL VddC Vdd48 Vdd3 VddP VddR VddS Vss PIN 53 33 9 10,18 1 45,37,32,25 FUNCTION Power supply for CPU & IOAPIC, 2.5V or 3.3V. Power supply for 48MHz output,3.3V. Power supply for 3V_66 output, 3.3V. Power supply for PCICLK, 3.3V. Power supply for REF0, 3.3V. Power supply for SDRAM_F,SDRAM[0:11], nominal 3.3V. 4,5,14,21,28,29,36, Circuit Ground. 41, 49.50 -4- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 5.0 FREQUENCY SELECTION BY HARDWARE FS4 FS3 FS2 FS1 FS0 CPU(MHz) 55.00 60.00 66.80 68.33 70.00 72.00 75.00 77.00 83.30 90.00 100.30 103.00 112.50 115.00 120.00 125.00 128.00 130.00 133.70 137.00 140.00 145.00 150.00 153.33 125.00 130.00 133.70 137.00 140.00 145.00 150.00 153.33 SDRAM(MHz) 3V66(MHz) 82.50 90.00 100.20 102.50 105.00 108.00 112.50 115.50 83.30 90.00 100.30 103.00 112.50 115.00 120.00 125.00 128.00 130.00 133.70 137.00 140.00 145.00 150.00 153.33 93.75 97.50 100.28 102.75 105.00 108.75 112.50 115.00 55.00 60.00 66.80 68.33 70.00 72.00 75.00 77.00 55.53 60.00 66.87 68.67 75.00 76.67 80.00 83.33 64.00 65.00 66.85 68.50 70.00 72.50 75.00 76.67 62.50 65.00 66.85 68.50 70.00 72.50 75.00 76.67 PCI(MHz) 27.50 30.00 33.40 34.17 35.00 36.00 37.50 38.50 27.77 30.00 33.43 34.33 37.50 38.33 40.00 41.67 32.00 32.50 33.43 34.25 35.00 36.25 37.50 38.33 31.25 32.50 33.43 34.25 35.00 36.25 37.50 38.33 IOAPIC (MHz) 13.75 15.00 16.70 17.08 17.50 18.00 18.75 19.25 13.88 15.00 16.72 17.17 18.75 19.17 20.00 20.83 16.00 16.25 16.71 17.13 17.50 18.13 18.75 19.17 15.63 16.25 16.71 17.13 17.50 18.13 18.75 19.17 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 -5- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 6. SERIAL CONTROL REGISTERS The Pin column lists the affected pin number and the @PowerUp column gives the state at true power up. Registers are set to the values shown only on true power up. "Command Code" byte and "Byte Count" byte must be sent following the acknowledge of the Address Byte. Although the data (bits) in these two bytes are considered "don't care", they must be sent and will be acknowledge. After that, the below described sequence (Register 0, Register 1, Register 2, ....) will be valid and acknowledged. Frequency Table Setting by I2C (SEL5 ~ SEL0) SSEL5 SSEL4 SSEL3 SSEL2 SSEL1 SSEL0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 CPU (MHz) 55.00 60.00 66.80 68.33 70.00 72.00 75.00 77.00 83.30 90.00 100.30 103.00 112.50 115.00 120.00 125.00 128.00 130.00 133.70 137.00 140.00 145.00 150.00 153.33 125.00 130.00 133.70 137.00 140.00 145.00 150.00 SDRAM (MHz) 82.50 90.00 100.20 102.50 105.00 108.00 112.50 115.50 83.30 90.00 100.30 103.00 112.50 115.00 120.00 125.00 128.00 130.00 133.70 137.00 140.00 145.00 150.00 153.33 93.75 97.50 100.28 102.75 105.00 108.75 112.50 3V66 (MHz) 55.00 60.00 66.80 68.33 70.00 72.00 75.00 77.00 55.53 60.00 66.87 68.67 75.00 76.67 80.00 83.33 64.00 65.00 66.85 68.50 70.00 72.50 75.00 76.67 62.50 65.00 66.85 68.50 70.00 72.50 75.00 PCI(MHz) 27.50 30.00 33.40 34.17 35.00 36.00 37.50 38.50 27.77 30.00 33.43 34.33 37.50 38.33 40.00 41.67 32.00 32.50 33.43 34.25 35.00 36.25 37.50 38.33 31.25 32.50 33.43 34.25 35.00 36.25 37.50 IOAPIC (MHz) 13.75 15.00 16.70 17.08 17.50 18.00 18.75 19.25 13.88 15.00 16.72 17.17 18.75 19.17 20.00 20.83 16.00 16.25 16.71 17.13 17.50 18.13 18.75 19.17 15.63 16.25 16.71 17.13 17.50 18.13 18.75 -6- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 0 1 1 1 1 1 153.33 CPU (MHz) 66.8 135.00 142.00 143.00 144.00 146.00 147.00 148.00 100.20 156.00 158.00 160.00 135.00 139.00 141.00 142.00 143.00 144.00 146.00 147.00 148.00 149.00 153.00 157.00 159.00 162.00 164.00 170.00 175.00 180.00 190.00 200.40 115.00 SDRAM (MHz) 133.00 135.00 142.00 143.00 144.00 146.00 147.00 148.00 133.00 156.00 158.00 160.00 101.25 104.25 105.75 106.50 107.25 108.00 109.50 110.25 111.00 111.75 114.75 117.75 119.25 121.50 123.00 127.50 116.67 120.00 95.00 133.60 76.67 3V66 (MHz) 66.80 67.50 71.00 71.50 72.00 73.00 73.50 74.00 66.80 78.00 79.00 80.00 67.50 69.50 70.50 71.00 71.50 72.00 73.00 73.50 74.00 74.50 76.50 78.50 79.50 81.00 82.00 85.00 58.30 60.00 63.33 66.80 38.33 PCI(MHz) 33.40 33.75 35.50 35.75 36.00 36.50 36.75 37.00 33.40 39.00 39.50 40.00 33.75 34.75 35.25 35.50 35.75 36.00 36.50 36.75 37.00 37.25 38.25 39.25 39.75 40.50 41.00 42.50 29.15 30.00 31.67 33.40 19.17 IOAPIC (MHz) 16.70 16.88 17.75 17.88 18.00 18.25 18.38 18.50 16.70 19.50 19.75 20.00 16.88 17.38 17.63 17.75 17.88 18.00 18.25 18.38 18.50 18.63 19.13 19.63 19.88 20.25 20.50 21.25 14.58 15.00 15.83 16.70 SSEL5 SSEL4 SSEL3 SSEL2 SSEL1 SSEL0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 -7- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 6.1 Register 0: CPU Frequency Select Register Bit 7 6 5 4 3 2 1 0 @PowerUp 0 0 0 0 0 0 0 0 Pin Description SSEL3 (Frequency table selection by software via I2C ) SSEL2 ( Frequency table selection by software via I2C) SSEL1 ( Frequency table selection by software via I2C) SSEL0 ( Frequency table selection by software via I2C) 0 = Selection by hardware 1 = Selection by software I2C - Bit (2, 7:4) SSEL4 (Frequency table selection by software via I2C ) SSEL5 (Frequency table selection by software via I2C ) 0 = Running 1 = Tristate all outputs 6.2 Register 1 : CPU Clock Register (1 = Active, 0 = Inactive) Bit 7 6 5 4 3 2 1 0 @PowerUp X X X 1 1 1 0 1 Pin 27 26 FS3# FS0# FS2# 24MHz(Active / Inactive) 48MHz(Active / Inactive) 1 = ± 0.25% Center type Spread Spectrum Modulation 0 = ± 0.5% Center type Spread Spectrum Modulation 0 = Normal 1 = Spread Spectrum enabled Reserved escription 6.3 Register 2: SDRAM Clock Register (1 = Active, 0 = Inactive) Bit 7 6 5 4 3 2 1 0 @PowerUp 1 1 1 1 1 1 1 1 Pin 39 40 42 43 44 46 47 48 SDRAM7 (Active / Inactive) SDRAM6 (Active / Inactive) SDRAM5 (Active / Inactive) SDRAM4 (Active / Inactive) SDRAM3 (Active / Inactive) SDRAM2 (Active / Inactive) SDRAM1 (Active / Inactive) SDRAM0 (Active / Inactive) Description -8- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 6.4 Register 3: PCI Clock Register (1 = Active, 0 = Inactive) Bit 7 6 5 4 3 2 1 0 @PowerUp 1 1 1 1 1 1 1 1 Pin 20 19 17 16 15 13 12 11 PCICLK7 (Active / Inactive) PCICLK6 (Active / Inactive) PCICLK5 (Active / Inactive) PCICLK4 (Active / Inactive) PCICLK3 (Active / Inactive) PCICLK2 (Active / Inactive) PCICLK1 (Active / Inactive) PCICLK0 (Active / Inactive) Description 6.5 Register 4: Additional Register (1 = Active, 0 = Inactive) Bit 7 6 5 4 3 2 1 0 @PowerUp 1 1 1 X 1 X 1 1 Pin 7 8 46 43 44 Reserved 3V66_0(Active / Inactive) 3V66_1(Active / Inactive) FS4# IOAPIC (Active / Inactive) FS1# CPUCLK1(Active / Inactive) CPUCLK0(Active / Inactive) Description 6.6 Register 5: SDRAM Clock Register (1 = Active, 0 = Inactive) Bit 7 6 5 4 3 2 1 0 @PowerUp 1 0 0 1 1 1 1 1 Pin 38 26 27 30 31 Description SKEW2(SDRAM to CPU Skew programming bit) SKEW1(SDRAM to CPU Skew programming bit) SKEW0(SDRAM to CPU Skew programming bit) SDRAM_F (Active / Inactive) SDRAM11 (Active / Inactive) SDRAM10 (Active / Inactive) SDRAM9 (Active / Inactive) SDRAM8 (Active / Inactive) -9- Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 6.7 Register 6: Winbond Chip ID Register (Read Only) Bit 7 6 5 4 3 2 1 0 @PowerUp 1 0 0 1 1 0 0 0 Pin Winbond Chip ID Winbond Chip ID Winbond Chip ID Winbond Chip ID Winbond Chip ID Winbond Chip ID Winbond Chip ID Winbond Chip ID Description 6.8 Register 7: Winbond Chip ID Register (Read Only) Bit 7 6 5 4 3 2 1 0 @PowerUp 0 1 0 1 0 0 0 1 Pin Winbond Chip ID Winbond Chip ID Winbond Chip ID Winbond Chip ID Winbond Version ID Winbond Version ID Winbond Version ID Winbond Version ID Description - 10 - Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 7.0 SPECIFICATIONS 7.1 Absolute Maximum Ratings Stresses greater than those listed in this table may cause permanent damage to the device. Precautions should be taken to avoid application of any voltage higher than the maximum rated voltages to this circuit. Maximum conditions for extended periods may affect reliability. Unused inputs must always be tied to an appropriate logic voltage level (Ground or Vdd). Symbol Vdd , VIN TSTG TB TA Parameter Voltage on any pin with respect to GND Storage Temperature Ambient Temperature Operating Temperature Rating - 0.5 V to + 7.0 V - 65°C to + 150°C - 55°C to + 125°C 0°C to + 70°C 7.2 Electronical Characteristics---Input/Output Vddq1=Vddq2 = Vddq3 = Vddq4 =3.3V, VddL1 =VddL2= 2.5V , TA = 0° C to +70° C Parameter Input Low Voltage Input High Voltage Input Low Current Input Low Current Input High Current Input Capacitance Symbol VIL VIH IIL IIL IIH CIN COUT CINX Operating Supply Current Power Down Supply Current Settling Time Delay Idd3 Idd2 Ts tPZH,tPZH tPLZ,tPZH 1 1 27 Min Vss-0.3 2.0 -5 -200 -5 5 5 6 45 100 600 3 10 10 Typ Max 0.8 Vdd+0.3 Units Vdc Vdc µA µA µA pF pF pF MA µA mS nS nS From first crossing to 1% target freq. Output enable delay Output enable delay Logic inputs Output capacitance Xin and Xout CPU = 66.6 MHz PCI = 33.3 Mhz with load No pull-up resistors Pull-up resistros Test Conditions - 11 - Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 7.3 Electronical Characteristics of CPU Clock Vdd=2.5V +/- 5%; CL=10-20pF Parameter Ouput Impedance Ouput Impedance Output Low Voltage Output High Voltage Output Low Current Output High Current Pull-Up Current Min Pull-Up Current Max Rise/Fall Time Min Between 0.4 V and 2.0 V Rise/Fall Time Max Between 0.4 V and 2.0 V Duty Cycle Skew Jitter Symbol RDSP RDSN VOL VOH IOL IOH IOH(min) IOH(max) TRF(min) TRF(max) Dt TSK Tsc-c 45 0.4 1.6 55 175 250 2.0 27 -27 -27 -27 30 -27 Min 13.5 13.5 Typ Max 40 40 0.4 Units Ohm Ohm V V MA MA MA MA ns ns % ps ps Vout = 1.0 V Vout = 2.0V 10pF Load 20pF Load VT=1.25V VT=1.25V VT=1.25V Test Conditions IOL=1mA IOH=-1mA 7.4 Electronical Characteristics of 3V66 Clock Vdd=3.3V +/- 5%; CL=10-30pF Parameter Ouput Impedance Ouput Impedance Output Low Voltage Output High Voltage Output Low Current Output High Current Rise/Fall Time Min Between 0.4 V and 2.0 V Rise/Fall Time Max Between 0.4 V and 2.0 V Duty Cycle Skew Jitter Symbol RDSP RDSN VOL VOH IOL IOH TRF(min) TRF(max) Dt TSK Tsc-c 45 2.4 30 -33 0.4 1.6 55 175 500 38 -33 Min 15 15 Typ Max 55 55 0.55 Units Ohm Ohm V V MA MA ns ns % ps ps 10pF Load 20pF Load VT=1.5V VT=1.5V VT=1.5V Test Conditions IOL=1mA IOH=-1mA - 12 - Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 7.5 Electronical Characteristics of SDRAM Clock Vdd=3.3V +/- 5%; CL=20-30pF Parameter Ouput Impedance Ouput Impedance Output Low Voltage Output High Voltage Output Low Current Output High Current Rise/Fall Time Min Between 0.4 V and 2.0 V Rise/Fall Time Max Between 0.4 V and 2.0 V Duty Cycle Skew Jitter Symbol RDSP RDSN VOL VOH IOL IOH TRF(min) TRF(max) Dt TSK Tsc-c 45 2.4 54 -54 0.4 1.6 55 250 250 54 -45 Min 13.5 13.5 Typ Max 40 40 0.45 Units Ohm Ohm V V MA MA ns ns % ps ps 10pF Load 20pF Load VT=1.5V VT=1.5V VT=1.5V Test Conditions IOL=1mA IOH=-1mA 7.6 Electronical Characteristics of PCI Clock Vdd=3.3V +/- 5%; CL=10-30pF Parameter Ouput Impedance Ouput Impedance Output Low Voltage Output High Voltage Output Low Current Output High Current Rise/Fall Time Min Between 0.4 V and 2.0 V Rise/Fall Time Max Between 0.4 V and 2.0 V Duty Cycle Skew Jitter Symbol RDSP RDSN VOL VOH IOL IOH TRF(min) TRF(max) Dt TSK Tsc-c 45 2.4 30 -33 0.5 2.0 55 500 500 38 -33 Min 15 15 Typ Max 55 55 0.55 Units Ohm Ohm V V MA MA ns ns % ps ps 10pF Load 20pF Load VT=1.5V VT=1.5V VT=1.5V Test Conditions IOL=1mA IOH=-1mA - 13 - Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 7.7 Electronical Characteristics of 48MHz, REF Clock Vdd=3.3V +/- 5%; CL=10-20pF Parameter Ouput Impedance Ouput Impedance Output Low Voltage Output High Voltage Output Low Current Output High Current RiseTime Fall Time Duty Cycle Skew Jitter Symbol RDSP RDSN VOL VOH IOL IOH TR TF Dt TSK Tsc-c 45 2.4 29 -29 1.8 1.7 27 -23 4 4 55 500 1000 Min 20 20 Typ Max 55 55 0.4 Units Ohm Ohm V V MA MA ns ns % ps ps 10pF Load 20pF Load VT=1.5V VT=1.5V VT=1.5V Test Conditions IOL=1mA IOH=-1mA 8.0 ORDERING INFORMATION Part Number W83195AR-25 Package Type 56 PIN SSOP Production Flow Commercial, 0°C to +70°C 9.0 HOW TO READ THE TOP MARKING W83195AR-25 28051234 814GAB 1st line: Winbond logo and the type number: W83195AR-25 2nd line: Tracking code 2 8051234 2: wafers manufactured in Winbond FAB 2 8051234: wafer production series lot number 3rd line: Tracking code 814 G A B 814: packages made in '98, week 14 G: assembly house ID; O means OSE, G means GR A: Internal use code B: IC revision - 14 - Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY All the trade marks of products and companies mentioned in this data sheet belong to their respective owners. - 15 - Publication Release Date: Jan. 2000 Revision 0.40 W83195AR-25 PRELIMINARY 10.0 PACKAGE DRAWING AND DIMENSIONS .035 .045 DIMENSION IN MM .045 .055 0.40/0.50 DIA E END VIEW DIMENSION IN INCH SYMBOL HE A A1 A2 b c D HE E e L L1 Y θ MIN. NOM MAX. MIN. NOM 2.41 0.095 0.101 2.57 2.79 0.41 0.008 0.012 0.20 0.30 0.088 0.090 2.34 2.24 2.29 0.25 0.20 0.34 0.008 0.010 0.13 0.25 0.005 0.720 0.400 18.2 18.42 18.54 9 10.16 10.31 10.41 7.42 0.51 0.61 7.52 0.64 0.81 1.40 7.59 0.76 1.02 0.08 8 MAX. 0.110 0.016 0.092 0.0135 0.010 TOP VIEW SEE DETAIL "A" c 0.725 0.730 0.406 0.410 D θ A2 Y SEATING PLANE e b SIDE VIEW A1 PARTING LINE c A 0.292 0.296 0.299 0.020 0.025 0.030 0.024 0.032 0.040 0.055 0.003 0 8 0 θ L L1 DETAIL"A" Headquarters No. 4, Creation Rd. III Science-Based Industrial Park Hsinchu, Taiwan TEL: 886-35-770066 FAX: 886-35-789467 www: http://www.winbond.com.tw/ Winbond Electronics (H.K.) Ltd. Rm. 803, World Trade Square, Tower II 123 Hoi Bun Rd., Kwun Tong Kowloon, Hong Kong TEL: 852-27516023-7 FAX: 852-27552064 Winbond Electronics (North America) Corp. 2730 Orchard Parkway San Jose, CA 95134 U.S.A. TEL: 1-408-9436666 FAX: 1-408-9436668 Taipei Office 11F, No. 115, Sec. 3, Min-Sheng East Rd. Taipei, Taiwan TEL: 886-2-7190505 FAX: 886-2-7197502 TLX: 16485 WINTPE Please note that all data and specifications are subject to change without notice. All the trade marks of products and companies mentioned in this data sheet belong to their respective owners. These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or s\\\\\\\\ - 16 - Publication Release Date: Jan. 2000 Revision 0.40