AH11BAL-PCB

AH11 Product Features • 150 – 3000 MHz • +44 dBm OIP3 (balanced configuration) The Communications Edge TM Product Information High Dynamic Range Dual Amplifier Product Description The AH11 is a high linearity amplifier for use in digital communication systems. It combines low noise figure and high intercept point into a low-cost SMT solution. This device extends the linear efficiency advantages of WJ’s AH1 to higher power levels by combining two internally matched die. This dual-amplifier configuration allows for the optimal design of balanced or push-pull operation. The amplifier can also be used for single-ended operation in each branch of a diversity receive system. A mature and reliable GaAs MESFET technology is employed to maximize linearity while achieving low noise figure. The package is a thermally enhanced lead-free/ green/RoHS-compliant SOIC-8 package thus allowing the device to achieve an MTTF greater than 100 years at a case temperature of 85 °C. All devices are 100% RF and DC tested. Functional Diagram 1 2 3 4 8 7 6 5 • +48 dBm OIP3 (dual push-pull configuration) • Single-ended performance: 13.5 dB Gain 2.7 dB Noise Figure +21 dBm P1dB • Single +5 Volt Supply • Lead-free/Green SOIC8 Pkg. Function Input (Amp 1) Ground Input (Amp 2) Output (Amp 1) Output (Amp 2) Applications • Mobile Infrastructure • Defense / Homeland Security • Fixed Wireless Pin No. 1 2, 3, 6, 7, Bottom Slug 4 5 8 Specifications (1) (Single-ended Performance) Parameter Test Frequency Gain Input Return Loss (2) Output Return Loss Output IP3 (3) Output P1dB Noise Figure Operating Current Range Supply Voltage Typical Performance (Balanced Configuration) Parameter Frequency S21 S11 S22 Output IP3 Noise Figure Supply Bias Units MHz dB dB dB dBm dBm dB mA V Min 12.4 Typ 800 13.5 8 15 +41 +21 2.7 150 +5 Max Units MHz dB dB dB dBm dB 900 12.2 -10 -18 +46 4.1 Typical 1900 11.2 -14 -10 +44 4.2 +5 V @ 300 mA 2100 10.6 -10 -10 +45 5.6 +37 120 180 Test conditions: T = 25 ºC, in a tuned application circuit (shown on page 2) Typical Performance (Dual P-P Configuration) 1. Test conditions unless otherwise noted: T = 25 ºC, Supply Voltage = +5 V, Frequency = 800 MHz, 50 Ω System, tested on each single-ended amplifier (there are two amplifiers in an AH11 package) 2. S21 and S11 can be improved in the band of interest with some slight input tuning. 3. 3OIP measured with two tones at an output power of +5 dBm/tone separated by 10 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. Slight OIP3 degradation of about 2 dB is expected to occur at lower temperatures (from 25 ºC to –40 ºC). Parameter Frequency S21 S11 S22 Output IP3 Noise Figure Supply bias Units MHz dB dB dB dBm dB Typical 900 1900 13.4 11.9 -19 -19 -12 -10 +48 +48 3.4 3.7 +5 V @ 600 mA Test conditions: T = 25 ºC, in a tuned application circuit (shown on pages 3 and 4) Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature Supply Voltage RF Input Power (continuous) Junction Temperature -40 to +85 °C -55 to +125 °C +6 V 4 dB above Input P1dB +220 °C Ordering Information Part No. AH11-G AH11BAL-PCB AH11PP900-PCB AH11PP1900-PCB Rating Description High Dynamic Range CATV Amplifier (lead-free/green/RoHS-compliant SOIC-8 Package) 0.6-2.1GHz Eval Board, Balanced Configuration 0.9GHz Eval Board, Dual Push-Pull Configuration 1.9GHz Eval Board, Dual Push-Pull Configuration Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 1 of 6 May 2006 AH11 The Communications Edge TM Product Information High Dynamic Range Dual Amplifier Balanced Circuit: 600 – 2100 MHz Performance Charts Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 2 of 6 May 2006 AH11 The Communications Edge TM Product Information High Dynamic Range Dual Amplifier Dual Push-Pull Circuit: 900 MHz Performance Charts Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 3 of 6 May 2006 AH11 The Communications Edge TM Product Information High Dynamic Range Dual Amplifier Dual Push-Pull Circuit: 1900 MHz Performance Charts Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 4 of 6 May 2006 AH11 The Communications Edge TM Product Information High Dynamic Range Dual Amplifier AH11-G Mechanical Information This package is lead-free/Green/RoHS-compliant. The plating material on the leads is NiPdAu. It is compatible with both lead-free (maximum 260 °C reflow temperature) and lead (maximum 245 °C reflow temperature) soldering processes. Outline Drawing Product Marking The component will be marked with an “AH11-G” designator with an alphanumeric lot code on the top surface of the package. The obsolete tin-lead package is marked with an “AH11” designator followed by an alphanumeric lot code. Tape and reel specifications for this part are located on the website in the “Application Notes” section. ESD / MSL Information ESD Rating: Value: Test: Standard: ESD Rating: Value Test: Standard: Class 1B Passes from 500 to 1000 V Human Body Model (HBM) JEDEC Standard JESD22-A114 Class IV Passes greater than 1000 V Charge Device Model (CDM) JEDEC Standard JESD22-C101 MSL Rating: Level 2 at +260 °C convection reflow Standard: JEDEC Standard J-STD-020A Functional Pin Layout Land Pattern Pin 1 2 3 4 5 6 7 8 Function RF input (Amp1 input) Ground Ground RF input (Amp2 input) RF output (Amp2 output) Ground Ground RF output (Amp1 output) The backside paddle is the Source and should be grounded for thermal and electrical purposes. Mounting Config. Notes Thermal Specifications Parameter Operating Case Temperature Thermal Resistance, Rth (1) Junction Temperature, Tj (2) 1. Rating -40 to +85 °C 28 °C/W 127 °C MTTF vs. GND Tab Temperature 1000 2. 3. 4. 100 5. Notes: 1. The thermal resistance is referenced from the hottest part of the junction to ground tab underneath the device. 2. This corresponds to the typical biasing condition of +5V, 300 mA at an 85 °C case temperature. A minimum MTTF of 1 million hours is achieved for junction temperatures below 160 °C. 10 6. 7. 8. 1 60 70 80 90 100 Tab Temperature (°C) 110 9. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80/.0135”) diameter drill and have a final plated through diameter of .25mm (.010”) Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. To ensure reliable operation, device ground paddle-toground pad solder joint is critical. Add mounting screws near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. For optimal thermal performance, expose soldermask on backside where it contacts the heatsink. RF trace width depends upon the PC board material and construction. Use 1 oz. Copper minimum. If the PCB design rules allow, ground vias should be placed under the land pattern for better RF and thermal performance. Otherwise ground vias should be placed as close to the land pattern as possible. All dimensions are in mm. Angles are in degrees. MTTF (million hrs) Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 5 of 6 May 2006 AH11 Freq (MHz) The Communications Edge TM Product Information High Dynamic Range Dual Amplifier Typical Device Data S-Parameters, single unmatched device (2 per package): VDS = +5 V, 100% IDSS, T = 25 °C, 50 Ω system, calibrated to device leads S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000 -2.65 -7.97 -8.57 -8.47 -8.24 -7.79 -7.18 -6.55 -6.03 -5.69 -5.55 -5.68 -5.86 -29.52 -44.15 -60.61 -80.72 -100.99 -120.81 -138.15 -152.70 -164.30 -173.54 176.22 166.67 153.06 17.80 15.28 14.91 14.60 14.22 13.80 13.27 12.69 12.11 11.57 11.12 10.76 10.40 164.25 158.50 147.54 134.66 121.38 108.59 96.13 84.26 73.25 62.88 52.70 42.57 31.81 -24.29 -21.31 -21.11 -21.11 -21.21 -21.21 -21.41 -21.62 -21.83 -21.99 -22.10 -22.16 -22.27 45.18 6.75 -3.83 -10.90 -17.00 -23.01 -28.54 -33.67 -38.35 -42.48 -46.41 -50.57 -55.21 -8.25 -19.01 -25.15 -29.26 -30.76 -29.83 -29.30 -29.12 -28.24 -26.58 -25.60 -26.12 -29.48 -39.80 -65.37 -69.25 -84.69 -115.12 -88.78 -94.19 -136.07 -112.00 -97.44 -90.19 -87.80 -82.67 Device S-parameters are available for download off of the website at: http://www.wj.com Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 6 of 6 May 2006