VG112-PCB

VG112 Product Features • • • • • • The Communications Edge TM Product Information PCS/UMTS-band Variable Gain Amplifier Product Description The VG112 is a PCS / UMTS-band high dynamic range variable gain amplifier (VGA) housed in a low profile Pb-free / green / RoHS-compliant surface-mount leadless QFN package that measures 6 x 6 mm square. The +30 dBm output compression point and +46 dBm output intercept point of the amplifier are maintained over the entire attenuation range, making the VG112 ideal for use in transmitter and receiver AGC circuits. The high gain of the dual-stage amplifier allows for more integration in a transceiver board while requiring minimal printed circuit board space. Superior thermal design allows the product to have a minimum MTTF rating of 100 years at a mounting temperature of +85 ºC. All devices are 100% RF & DC tested and packaged on tape and reel for automated surfacemount assembly. Functional Diagram Gain Ctrl 7 GND 8 GND 9 GND 10 RF IN 11 GND 12 GND 13 GND 14 15 GND 16 GND 17 GND 18 GND 19 Vbias2 20 GND 21 GND 6 GND GND 2 5 4 3 Vbias1 1 28 GND 27 Vcc1 26 GND 25 RF OUT / Vcc2 24 GND 23 RF OUT / Vcc2 22 GND GND GND GND 1800 – 2200 MHz bandwidth 25 dB Gain at 1.9 GHz 28 dB Attenuation Range +46 dBm Output IP3 +30 dBm P1dB Constant IP3 & P1dB over attenuation range • +5V Single voltage supply • Pb-free / green / RoHS-compliant 6x6 mm QFN package • MTTF > 100 years Amp Variable Attenuator Applications • Xmit & Rcv AGC circuitry for mobile infrastructure Specifications (1) Parameter Operational Bandwidth Test Frequency Gain at min. attenuation Input Return Loss Output Return Loss Output P1dB Output IP3 Noise Figure at min. attenuation Gain Variation Range Gain Variation Control Voltage, VCTRL Supply Voltage, VCC Operating Amplifier Current Range Gain Control Pin Current Units MHz MHz dB dB dB dBm dBm dB dB V V mA mA Min 1800 20.5 Typ 2140 23 18 8.2 +30 +46 8 28 Max 2200 Conditions See note 1 +43 23.5 0 350 4.5 +5 415 475 20 See note 2 VCTRL = 0 V See note 3 See note 1 Pin 25 VCTRL = 4.5 V. See note 1. 1. Test conditions unless otherwise noted: 25 ºC, Vcc = +5 V in a tuned application circuit. Vctrl is the control voltage through a 220 Ω dropping resistor as shown in the same application circuit. 2. 3OIP measured with two tones at an output power of +15 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. The gain variation range is measured as the difference in gain with Vctrl = 0V and Vctrl = 4.5V at 2.14 GHz. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature Pin 5 (Gain Control) Current Junction Temperature -40 to +85 °C -55 to +125 °C 30 mA +250 °C Rating Ordering Information Part No. VG112-G VG112-PCB Description PCS/UMTS-band Variable Gain Amplifier (lead-free/green/RoHS-compliant QFN package) 2140 MHz Fully Assembled Application Board Specifications and information are subject to change without notice Operation of this device above any of these parameters may cause permanent damage. WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 1 of 4 May 2006 VG112 The Communications Edge TM Product Information PCS/UMTS-band Variable Gain Amplifier 2140 MHz Application Circuit Performance Performance using the circuitry on the VG112-PCB Evaluation Board Circuit Board Material: .014” FR-4, 4 layers, .062” total thickness • The center of C5 should be placed 5mm (.197”) away from the edge of the VG112. • The input trace is a high impedance line and is needed to get a good input match into the VGA. • The board is optimized for performance at 2140 MHz. Performance at 1960 MHz can be optimized by replacing C5 with 2.7 pF at location A on the WJ VG112 evaluation board. Ref. Des. C1, C7, C10 C2, C3, C4, C8, C9 C5 C6 L1, L2 R1 R3 R2, R4 U1 Bill of Materials Description 47 pF Chip Capacitor 1000 pF Chip Capacitor 2.4 pF Chip Capacitor 3.3 μF Chip Capacitor 18 nH Chip Inductor 220 Ω Chip Resistor 75 Ω Chip Resistor 0 Ω Chip Resistor VG112-G VGA Size 0603 0603 0603 0805 0603 0603 0603 0603 QFN 6x6 S21 vs. Frequency Vctrl=0V (Maximum Gain Setting) S11 vs. Frequency Vctrl=0V (Maximum Gain Setting) S22 vs. Frequency Vctrl=0V (Maximum Gain Setting) 28 26 S 2 1 (d B ) S 1 1 (d B ) 0 0 -40 °C +25 °C +85 °C -5 -5 S 2 2 (d B ) -10 -15 -20 -40 °C +25 °C +85 °C 24 22 20 -40 °C +25 °C +85 °C -10 -15 -20 -25 1800 18 1800 1900 2000 Frequency (MHz) 2100 2200 1900 2000 Frequency (MHz) 2100 2200 -25 1800 1900 2000 Frequency (MHz) 2100 2200 S21 vs. Frequency vs. Control Voltage S11 vs. Frequency vs. Control Voltage S22 vs. Frequency vs. Control Voltage 30 20 S 1 1 (d B ) S 2 1 (d B ) 10 0 Vctrl=0.00V Vctrl=1.52V Vctrl=0.73V Vctrl=2.20V Vctrl=1.06V Vctrl=4.50V 0 -5 -10 -15 -20 -25 1800 Vctrl=0.00V Vctrl=1.52V Vctrl=0.73V Vctrl=2.20V Vctrl=1.06V Vctrl=4.50V 0 -5 S 2 2 (d B ) -10 -15 -20 -25 1800 Vctrl=0.00V Vctrl=1.52V Vctrl=0.73V Vctrl=2.20V Vctrl=1.06V Vctrl=4.50V -10 1800 1900 2000 Frequency (MHz) 2100 2200 1900 2000 Frequency (MHz) 2100 2200 1900 2000 Frequency (MHz) 2100 2200 Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 2 of 4 May 2006 VG112 The Communications Edge TM Product Information PCS/UMTS-band Variable Gain Amplifier 2140 MHz Application Circuit Performance Performance using the circuitry on the VG112-PCB Evaluation Board OIP3 vs. Output Power vs. Temperature 48 46 O IP 3 ( d B m ) O IP 3 ( d B m ) 44 42 40 +25 °C 38 10 12 14 16 18 Output Power per tone (dBm) 20 -40 °C +85 °C 38 10 12 14 16 18 Output Power per tone (dBm) 20 frequency = 2140, 2141 MHz, 0dB Atten. OIP3 vs. Output Power vs. Temperature 48 46 44 42 40 +25 °C -40 °C +85 °C 38 10 O IP 3 ( d B m ) frequency = 2140, 2141 MHz, 5dB Atten. OIP3 vs. Output Power vs. Temperature 48 46 44 42 40 +25 °C -40 °C +85 °C 20 frequency = 2140, 2141 MHz, 10dB Atten. 12 14 16 18 Output Power per tone (dBm) OIP3 vs. Output Power vs. Temperature 48 46 O IP 3 ( d B m ) 44 42 40 +25 °C 38 10 12 14 16 18 Output Power per tone (dBm) 20 -40 °C +85 °C 38 10 frequency = 2140, 2141 MHz, 15dB Atten. OIP3 vs. Pout vs. Attenuation Setting 48 46 44 42 40 0 dB Atten 5 dB Atten 10 dB Atten 15 dB Atten 12 14 16 18 Output Power per tone (dBm) 20 ACLR vs. Channel Power 3GPP W-CDMA, Test Model 1+64 DPCH, ±5 MHz offset, 2140 MHz frequency = 2140, 2141 MHz, +25 °C IMD products vs. Output Power -40 IM D p ro d u c ts ( d B c ) -50 -60 -70 -80 10 12 14 16 18 Output Power per tone (dBm) Gain vs. Vctrl 2140 MHz fundamental frequency = 2140, 2141 MHz; +25 °C, 0dB Atten P1dB vs. Temperature 32 30 P 1 d B (d B m ) 28 26 24 A C L R (d B c ) frequency = 2140 MHz, 0dB Atten. O IP 3 ( d B m ) IMD_Low IMD_High -40 -45 -50 -55 -40 C 22 20 -40 -15 10 35 Temperature (°C) 2140 MHz +25 C 21 +85 C 22 -60 60 85 18 19 20 Output Channel Power (dBm) Normalized Gain vs. Vctrl 0 N o rm a liz e d G a in ( d B ) Noise Figure vs. Frequency vs. Temperature Vctrl=0V (Maximum Gain Setting) 30 25 °C G a in ( d B ) 20 10 0 -10 0 1 2 Vctrl (V) 3 4 5 -40 °C 85 °C 10 25 °C -40 °C 85 °C -40 °C +25 °C +85 °C -5 9 N F (d B ) 8 7 6 5 1800 -10 -15 -20 -25 -30 0 1 2 Vctrl (V) 3 4 5 1900 2000 Frequency (MHz) 2100 2200 Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 3 of 4 May 2006 VG112 The Communications Edge TM Product Information PCS/UMTS-band Variable Gain Amplifier VG112-G Mechanical Information This package is lead-free/green/RoHS-compliant. The plating material on the pins is annealed matte tin over copper. It is compatible with both lead-free (maximum 260 °C reflow temperature) and leaded (maximum 245 °C reflow temperature) soldering processes. Outline Drawing Product Marking The component will be lasermarked with a “VG112-G” designator with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part will be located on the website in the “Application Notes” section. ESD / MSL Information ESD Rating: Value: Test: Standard: ESD Rating: Value: Test: Standard: Class 1B Passes 500V to