2609031181000

Dimensions: [mm] Recommended Land Pattern: [mm] 22,0 24,0 1,5 4,0 2,0 1,0 6,0 24,0 3,8 ±0,2 Scale - 2:1 RESERVED MODE_1 WAKE-UP RESERVED RESERVED RESERVED RX_IND /RESET RESERVED Product Specific Pinning: GND 27,0 ±0,4 4,0 2,0 1,0 22,0 TX_IND 4,0 2,2 14,0 2,0 13 1,5 23 18,0 12 1 23 13 i4 TEST TEST TEST 12 RESERVED RESERVED RESERVED RESERVED RESERVED /RTS URXD UTXD VCC GND 1 ANT TEST BOOT 17,0 ±0,4 i1 Scale - 2:1 undefined areas reserved for future use Scale - 2:1 CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE SeS 004.000 2020-06-15 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION WIRL-PRO8 Radio module 868MHz Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com ORDER CODE 2609031181000 BUSINESS UNIT STATUS PAGE eiSmart Valid 1/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. General Properties: RF-Electrical Properties: Properties Test conditions Communication Protocol/ Standard Antenna Connector Type Microcontroller Radio Chipset Value Unit Proprietary (P2P, star, mesh) ANTConn RF pad µC SoC RF-IC TI - CC1310 Properties Test conditions Value Unit Frequency min. fmin. VDD,typ,TAMB = 25 °C, RH = 60 % 869.4 MHz Frequency max. fmax. VDD,typ,TAMB = 25 °C, RH = 60 % 869.65 MHz Two-ray ground-reflection model 20000 m 6 m Line of Sight Range Line of Sight Conditions: Antenna Height Memory Size (Flash) 131072 B RF Bitrate max. latest FW revision 100 kbps Memory Size (RAM) 20480 B Supply Current Transmitting ITX VDD,typ,TAMB = 25 °C, RH = 60 % 500 mA Supply Current Receiving IRX VDD,typ,TAMB = 25 °C, RH = 60 % 12 mA 27 dBm Radio channel min. 129 Radio channel max. Interface 1 Interface 1 Bitrate Range Number of I/O Ports 132 IO1 Output Power 50 Ohm UART IO1 Bitrate latest FW revision IOPorts 115.2 latest FW revision Rb, max. kbps 11 PTx, 50 Ω TAMB = 25 °C, RH = 60 % RX sensitivity max. Rxsens, 50 Ω 50 Ω -124 dBm RX sensitivity Condition Bitrate Rxsens, kbps latest FW revision 0.625 kbps Product Specific Pinning: Electrical Properties: Pin Pad Description I/O Test conditions Value Unit ANT 1 external antenna connection -- Operating Supply Voltage Min. VDD min. TAMB = 25 °C, RH = 60 % 2.2 V GND 2 Negative supply voltage Supply Operating Supply Voltage Max. VDD max. TAMB = 25 °C, RH = 60 % 3.7 V VCC 3 Positive supply voltage Supply Recommended Supply Voltage VDD typ TAMB = 25 °C, RH = 60 % 3.6 V UTXD 4 UART transmit Output VDD,typ,TAMB = 25 °C, RH = 60 % 0.9 µA URXD 5 UART receive Input /RTS 6 Ready to send signal Output RESERVED 7 see manual for more details -- RESERVED 8 see manual for more details -- RESERVED 9 see manual for more details -- RESERVED 10 see manual for more details -- RESERVED 11 see manual for more details -- BOOT 12 see manual for more details Input RESERVED 13 see manual for more details -- WAKE_UP 14 see manual for more details Input Properties Supply Current Sleep Isleep Additional General Information: Ambient Temperature (referring to IR) -40 up to +85 °C Operating Temperature -40 up to +85 °C Storage Conditions (in original packaging) < 40 °C ; < 90 % RH CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE SeS 004.000 2020-06-15 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION WIRL-PRO8 Radio module 868MHz Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com ORDER CODE 2609031181000 BUSINESS UNIT STATUS PAGE eiSmart Valid 2/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Product Specific Pinning: Pin Pad Description I/O MODE_1 15 see manual for more details Input RESERVED 16 see manual for more details -- RESERVED 17 see manual for more details -- RESERVED 18 see manual for more details -- /RESET 19 Reset-Input Input RX_IND 20 radio activity indicator for reception Output TX_IND 21 radio activity indicator for transmission Output RESERVED 22 see manual for more details -- GND 23 Negative supply voltage Supply TEST i1…i4 Testpin, DO NOT CONNECT -- CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE SeS 004.000 2020-06-15 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION WIRL-PRO8 Radio module 868MHz Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com ORDER CODE 2609031181000 BUSINESS UNIT STATUS PAGE eiSmart Valid 3/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Tape and Reel: [mm] K0 T E P0 P2 W3 W1 close to center A W S B0 B N D F A D0 Packaging Specification - Reel: [mm] d C A D1 Cover tape P1 T1 A0 W2 T2 Feeding direction End detail B Start B Cover Tape Chip Cavity Sprocket Hole No Component min.160mm Components No Component min.100mm Cover Tape min. 400mm Embossment Packaging is refered to the international standard IEC 60286-3:2013 Tape Type 3 A0 B0 W T T1 T2 K0 P0 P1 P2 D0 (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) typ. typ. ±0,3 ref. max. typ. typ. ±0,1 ±0,1 ±0,15 +0,1/ -0,0 17,60 27,60 44,00 0,35 0,10 4,55 4,10 4,00 24,00 2,00 1,50 D0 / 2 (mm) +0,05/ -0,0 0,75 D1 d E S F (mm) (mm) (mm) (mm) (mm) Material min. ±0,05 ±0,1 ±0,1 ±0,1 2,00 0,20 1,75 40,40 20,20 Polystyrene Qty. (pcs.) A (mm) ± 2,0 330,00 B (mm) min. 1,50 C (mm) min. 12,80 D (mm) min. 20,20 N (mm) min. 80,00 W1 (mm) + 2,0 44,40 W2 (mm) max. 50,40 W3 (mm) min. 43,90 W3 (mm) max. 47,40 Material Polysytrene/ Polyurethane 400 165° -180° CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE SeS 004.000 2020-06-15 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION WIRL-PRO8 Radio module 868MHz Pull-of force Tape width 44 mm 0,1 N - 1,3 N Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com ORDER CODE 2609031181000 BUSINESS UNIT STATUS PAGE eiSmart Valid 4/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Cautions and Warnings: The following conditions apply to all goods within the product series of wireless connectivity of Würth Elektronik eiSos GmbH & Co. KG: General: • This electronic component is designed and developed with the intention for use in general electronic equipment. • Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury. • Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. • The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved. • Do not drop or impact the components, the component may be damaged. • Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not guarantee any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time. • The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products. Product specific: Soldering: • The solder profile must comply with the technical product specifications. All other profiles will void the warranty. • All other soldering methods are at the customer’s own risk. • Conformal coating may affect the product performance. Storage Conditions: • A storage of Würth Electronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment. • Do not expose the components to direct sunlight. • The storage conditions in the original packaging are defined according to DIN EN 61760-2. • If there is a moisture sensitive component, the storage condition in the original packaging is defined according to IPC/JEDEC-JSTD-033. It is also recommended to return the component to the original moisture proof bag and reseal the moisture proof bag again. • ESD prevention methods need to be followed for manual handling and processing by machinery. • The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Handling: • Violation of the technical product specifications such as exceeding the nominal rated current, will void the warranty. • Violation of the technical product specifications such as but not limited to exceeding the absolute maximum ratings will void the conformance to regulatory requirements. • The edge castellation is designed and made for prototyping, i.e. hand soldering purposes only. • Non-antenna modules must be equipped with a proper antenna having specific characteristics. • The applicable country regulations and specific environmental regulations must be observed. • Do not disassemble the product. Evidence of tampering will void the warranty. These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable. However, no responsibility is assumed for inaccuracies or incompleteness. All topics are described in a more detailed manner in the manual for each product. Cleaning and Washing: • Washing agents used during the production to clean the customer application might damage or change the characteristics of the component. Washing agents may have a negative effect on the long-term functionality of the product. • Using a brush during the cleaning process could break the module. Therefore, we do not recommend using a brush during the PCB cleaning process. Potting and Coating: • If the product is potted in the customer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the component. Expansion could damage components. We recommend a manual inspection after potting to avoid these effects. CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE SeS 004.000 2020-06-15 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION WIRL-PRO8 Radio module 868MHz Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com ORDER CODE 2609031181000 BUSINESS UNIT STATUS PAGE eiSmart Valid 5/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Important Notes 6. Product Life Cycle The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG: Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 1. General Customer Responsibility Some goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not. 2. Customer Responsibility related to Specific, in particular Safety-Relevant Applications It has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications. In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at www.we-online.com. 7. Property Rights All the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used. 8. General Terms and Conditions Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at www.we-online.com. 3. Best Care and Attention Any product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty. 4. Customer Support for Product Specifications Some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter. 5. Product R&D Due to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected. CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE SeS 004.000 2020-06-15 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION WIRL-PRO8 Radio module 868MHz Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com ORDER CODE 2609031181000 BUSINESS UNIT STATUS PAGE eiSmart Valid 6/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.