744290283

Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: Properties 6 5 17,6 1,6 10,16 10 5 14,5 max. Tol. mH ±30% 0.3 A max. 2.8 Ω max. 220000 nH typ. 500 V (AC) max. 80 V Inductance L 10 kHz/ 50 mV 28 IR ΔT = 40 K DC Resistance RDC @ 20 °C Leakage Inductance LS 1 MHz/ 1 mA Insulation Test Voltage VT 50 Hz Rated Voltage VR RoHS Approval Compliant [2011/65/EU&2015/863] REACh Approval Conform or declared [(EC)1907/2006] 7,8 - 0,1 Scale - 1,5:1 Schematic: 0~ 5° 9,5 max. Unit 2 Certification: 6 2,54 17,6 max. 1 10,16 u 0,1 2,54 u 0,05 10 Value N Rated Current 2,8 1 Test conditions Number of windings 12,5 u 0,1 General Properties: 1 1 10 2 5 6 It is recommended that the temperature of the component does not exceed +125 °C under worst case conditions Ambient Temperature (referring to IR) -40 up to +85 °C Operating Temperature -40 up to +125 °C Storage Conditions (in original packaging) < 40 °C ; < 75 % RH Moisture Sensitivity Level (MSL) 1 Test conditions of Electrical Properties: +20 °C, 33 % RH if not specified differently Scale - 1,5:1 CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE ACG 003.000 2021-02-10 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com WE-UCF SMT Common Mode Line Filter ORDER CODE 744290283 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1712 eiSos Valid 1/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Typical Impedance Characteristics: Test Setup: 1000000 100000 According to CISPR 17 Impedance [Ω] 10000 1´ (GND) 2´ (GND) Port 1 1 1000 1 2 Port 2 2 4 4 DUT 3 3 Port 3 100 Port 4 3´ (GND) 4´ (GND) GND 10 Network Analyzer: Keysight N5242B or equivalent 1 0.001 0.01 0.1 1 10 Frequency [MHz] Z (comm) Z (diff) CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE ACG 003.000 2021-02-10 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com WE-UCF SMT Common Mode Line Filter ORDER CODE 744290283 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1712 eiSos Valid 2/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Tape: [mm] Packaging Specification - Reel: [mm] P0 K0 P2 T E A W3 W1 close to center A N D B W S B0 F D0 d C A0 A Top Cover Tape P1 T1 T2 End Feeding direction Start Carrier Tape detail B Cover Tape Cover Tape B No Component min. 160mm Components No Component min. 100mm Chip Cavity Sprocket Hole Embossment Cover Tape min. 400mm packaging is reffered to the international standard IEC 60286-3:2013 Tape Type Tolerance Value 3 A0 (mm) typ. 13,20 B0 (mm) typ. 17,50 W (mm) ±0,3 32,00 T (mm) ref. 0,50 T1 (mm) ref. 0,10 T2 (mm) typ. 10,50 K0 (mm) typ. 10,30 P0 (mm) ±0,1 4,00 P1 (mm) ±0,1 20,00 P2 (mm) ±0,1 2,00 D0 (mm) +0,1/ -0,0 1,50 D0 / 2 (mm) +0,05/ -0,0 0,75 D1 (mm) min. 2,00 d (mm) ±0,05 0,20 E (mm) ±0,1 1,75 S (mm) ±0,1 28,40 F (mm) Material ±0,1 14,20 Polystyrene Qty. (pcs.) B (mm) min. 1,50 C (mm) min. 12,80 D (mm) min. 20,20 N (mm) min. 80,00 W1 (mm) + 2,0 32,40 W2 (mm) max. 38,40 W3 (mm) min. 31,90 W3 (mm) max. 35,40 Material Polystyrene 250 165° - 180° CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE ACG 003.000 2021-02-10 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION Pull-of force Tape width Tolerance Value A (mm) ± 2,0 330,00 32 mm 0,1 N - 1,3 N Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com WE-UCF SMT Common Mode Line Filter ORDER CODE 744290283 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1712 eiSos Valid 3/6 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max Ts min Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) Liquidous Temperature tL Preheat Area TC –5°C Value Preheat Temperature Min 60 - 120 seconds 3 °C/ second max. TL 217 °C Time tL maintained above TL tL 60 - 150 seconds Peak package body temperature Tp Tp ≤ Tc, see Table below Time within 5°C of actual peak temperature tp 20 - 30 seconds Ramp-down Rate (TP to TL) 6 °C/ second max. Time 25°C to peak temperature 8 minutes max. refer to IPC/ JEDEC J-STD-020E tS Package Classification Reflow Temperature (Tc): Volume mm³ 350-2000 Volume mm³ >2000 PB-Free Assembly | Package Thickness 260 °C < 1.6 mm 260 °C 260 °C PB-Free Assembly | Package Thickness 260 °C 1.6 mm - 2.5 mm 250 °C 245 °C PB-Free Assembly | Package Thickness 250 °C > 2.5 mm 245 °C 245 °C Properties 25 Time 25°C to Peak Time Volume mm³