750316016

Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: Properties Test conditions Value Unit Tol. 60 µH min. Inductance L N1+N2/ 10 kHz/ 10 mV Turns Ratio n N1+N2 : N3+N4+N5+N6 1:2.57 n N1+N2 : N4+N5 1:1.14 Turns Ratio DC Resistance 1 RDC 1 N1+N2/ 20 °C 0.13 Ω max. DC Resistance 2 RDC 2 N4+N5/ 20 °C 0.128 Ω max. DC Resistance 3 RDC 3 N3+N4+N5+N6/ 20 °C 0.286 Ω max. Voltage-Time ∫Udt N1/ bipolar waveform 8.9 Vµs Leakage Inductance LS N1+N2/ 100 kHz/ 10 mV 160 nH Insulation Test Voltage VT N1,2 => N3,4,5,6 2500 V (AC) typ. Certification: RoHS Approval Compliant [2011/65/EU&2015/863] REACh Approval Conform or declared [(EC)1907/2006] Schematic: 10 N3 9 2 General Information: Operating Temperature N1 N4 -40 up to +125 °C Storage Conditions (in original packaging) < 40 °C ; < 75 % RH Storage Conditions (for single parts) -20 up to +60 °C 8 3 N2 N5 7 4 Moisture Sensitivity Level (MSL) 1 Electrical Specifications @ 25°C unless otherwise noted Patent Protected by US10,575,419 N6 6 Patent Protected by US10,575,419 Product Marking: Pin 1 Marking • 750316016 Lot and date code CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 005.001 2023-03-14 ISO 2768-1m PROJECTION METHOD DESCRIPTION WE-PPTI Push-Pull Transformer Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750316016 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1212 Midcom Valid 1/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Typical Application: Properties Value Unit Vin 5 V (DC) Output Voltage 1 VOut1 12.85 V Output Current 1 IOut1 100 mA Output Voltage 2 VOut2 5.7 V Output Current 2 IOut2 200 mA Output Voltage 3 VOut3 -5.7 V Output Current 3 IOut3 200 mA Output Voltage 4 VOut4 -12.85 V Output Current 4 IOut4 100 mA Switching Frequency fswitch 400 kHz Input Voltage Input: N1 / N2 Output 1: N3 / N4 Output 2: N4 Output 3: N5 Output 4: N5 / N6 Table shows a typical application. Values may vary by application. Designed to Comply With: Standard IEC60950-1, EN60950-1, UL60950-1/CSA60950-1, AS/NZS60950.1 Condition Functional insulation for a primary circuit at a working voltage of 265Vrms, 400Vpeak, Overvoltage Category II. CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 005.001 2023-03-14 ISO 2768-1m PROJECTION METHOD DESCRIPTION WE-PPTI Push-Pull Transformer Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750316016 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1212 Midcom Valid 2/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Tape: [mm] Packaging Specification - Reel: [mm] W3 A B N D W1 close to center C W2 detail B Cover Tape B Chip Cavity Sprocket Hole Embossment Tape Type Tolerance Value 2a A0 (mm) typ. 12.4 B0 (mm) typ. 11.7 W (mm) ±0.3 24 T (mm) ±0.05 0.4 T1 (mm) ±0.0025 0.051 T2 (mm) typ. 4.441 K0 (mm) typ. 4 P0 (mm) ±0.10 4 P1 (mm) ±0.10 16 P2 (mm) ±0.10 2 D0 (mm) ±0.05 1.55 D0 / 2 (mm) typ. 0.775 D1 (mm) +0.25 1.5 E (mm) ±0.10 1.75 F (mm) 11.5 Material Black Conductive PS Qty. (pcs.) 950 165° - 180° Tolerance Value A (mm) max 330 B (mm) min. 1,50 C (mm) min. 12,80 D (mm) min. 20,20 N (mm) typ. 101.6 W1 (mm) 2 24.4 CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 005.001 2023-03-14 ISO 2768-1m W2 (mm) max 30.4 W3 (mm) min. 23.9 W3 (mm) max 27.4 Material PS PROJECTION METHOD DESCRIPTION WE-PPTI Push-Pull Transformer Pull-off force Tape width 24 mm 0,1 N - 1,3 N Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750316016 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1212 Midcom Valid 3/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Carton: [mm] H C H IC Packaging Specification - Inner Carton: [mm] L IC W IC L Tolerance Value LIC (mm) typ. 339,00 WIC (mm) typ. 362,00 HIC (mm) typ. 54,00 Qty. (pcs.) 950 Material Tolerance Value Paper LC (mm) typ. 365,12 C WC (mm) typ. 342,90 W HC (mm) typ. 215,90 C No. of Inner Carton (pcs.) Qty. (pcs.) Material 4 3800 Paper CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 005.001 2023-03-14 ISO 2768-1m PROJECTION METHOD DESCRIPTION WE-PPTI Push-Pull Transformer Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750316016 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1212 Midcom Valid 4/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max tL Preheat Area Ts min TC –5°C Value Preheat Temperature Min Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) 60 - 120 seconds 3 °C/ second max. Liquidous Temperature TL 217 °C Time tL maintained above TL tL 60 - 150 seconds Peak package body temperature Tp Tp ≤ Tc, see Table below Time within 5°C of actual peak temperature tp 20 - 30 seconds Ramp-down Rate (TP to TL) 6 °C/ second max. Time 25°C to peak temperature 8 minutes max. refer to IPC/ JEDEC J-STD-020E tS Package Classification Reflow Temperature (Tc): Volume mm³ 350-2000 Volume mm³ >2000 PB-Free Assembly | Package Thickness 260 °C < 1.6 mm 260 °C 260 °C PB-Free Assembly | Package Thickness 260 °C 1.6 mm - 2.5 mm 250 °C 245 °C PB-Free Assembly | Package Thickness 250 °C > 2.5 mm 245 °C 245 °C Properties 25 Time 25°C to Peak Time Volume mm³