Dimensions: [mm]
Recommended Land Pattern: [mm]
Electrical Properties:
Properties
Test conditions
Inductance
Turns Ratio
Value
Unit
Tol.
L
N1/ 10 kHz/ 100 mV
30
µH
±10%
n
N1 : N2
3:1
ISAT
Saturation Current
2.6
A
typ.
DC Resistance 1
RDC 1 N1/ 20 °C
N1/ |ΔL/L| < 20 %
0.13
Ω
±10%
DC Resistance 2
RDC 2 N2/ 20 °C
0.019
Ω
±20%
max.
Leakage Inductance
LS
N1/ 100 kHz/ 10 mV
900
nH
Insulation Test Voltage
VT
N1 => N2
625
V (AC)
Certification:
RoHS Approval
Compliant [2011/65/EU&2015/863]
REACh Approval
Conform or declared [(EC)1907/2006]
Schematic:
General Information:
1
5+6
N1
N2
Operating Temperature
-40 °C up to +125 °C
Storage Conditions (in original
packaging)
< 40 °C ; < 75 % RH
Moisture Sensitivity Level (MSL)
1
Test conditions of Electrical Properties: +20 °C, 33 % RH if not specified differently
4
Application of the transformer allows for the leadwires between
terminals 5&6 and 7&8 to solder bridge
Product Marking:
Pin 1
Marking
7+8
•
750317605
Lot and date code
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
WJK
003.001
2024-07-03
ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
WE-FLYTI Flyback Transformer
Wurth Electronics Midcom Inc. Headquarters
121 Airport Drive
57201 Watertown, SD
United States
Phone: +1 (605) 886-4385
www.we-online.com/midcom
midcom@we-online.com
ORDER CODE
750317605
SIZE/TYPE
BUSINESS UNIT
STATUS
PAGE
EP7
Midcom
Valid
1/6
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic
component which is used in electrical circuits that require high safety and reliability functions or performance.
Typical Application:
Properties
Value
Version
Flyback
Unit
Vin
12 - 70
V (DC)
Switching Frequency
fswitch
350
kHz
Output Voltage 1
VOut1
5
V
Output Current 1
IOut1
1
A
Input Voltage
Input: N1
Output 1: N2
Table shows a typical application. Values may vary by application.
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
WJK
003.001
2024-07-03
ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
WE-FLYTI Flyback Transformer
Wurth Electronics Midcom Inc. Headquarters
121 Airport Drive
57201 Watertown, SD
United States
Phone: +1 (605) 886-4385
www.we-online.com/midcom
midcom@we-online.com
ORDER CODE
750317605
SIZE/TYPE
BUSINESS UNIT
STATUS
PAGE
EP7
Midcom
Valid
2/6
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic
component which is used in electrical circuits that require high safety and reliability functions or performance.
Classification Reflow Profile for SMT components:
Classification Reflow Soldering Profile:
Profile Feature
Tp
tp
Max. Ramp Up Rate
Max. Ramp Down Rate
TL
Temperature
Ts max
tL
Preheat Area
Ts min
TC –5°C
Value
Preheat Temperature Min
Ts min 150 °C
Preheat Temperature Max
Ts max 200 °C
Preheat Time ts from Ts min to Ts max
ts
60 - 120 seconds
Ramp-up Rate (TL to TP)
3 °C/ second max.
Liquidous Temperature
TL
217 °C
Time tL maintained above TL
tL
60 - 150 seconds
Peak package body temperature
Tp
Tp ≤ Tc, see Table below
Time within 5°C of actual peak
temperature
tp
20 - 30 seconds
Ramp-down Rate (TP to TL)
6 °C/ second max.
Time 25°C to peak temperature
8 minutes max.
refer to IPC/ JEDEC J-STD-020E
tS
Package Classification Reflow Temperature (Tc):
Volume mm³
350-2000
Volume mm³
>2000
PB-Free Assembly | Package Thickness 260 °C
< 1.6 mm
260 °C
260 °C
PB-Free Assembly | Package Thickness 260 °C
1.6 mm - 2.5 mm
250 °C
245 °C
PB-Free Assembly | Package Thickness 250 °C
> 2.5 mm
245 °C
245 °C
Properties
25
Time 25°C to Peak
Time
Volume mm³
很抱歉,暂时无法提供与“750317605”相匹配的价格&库存,您可以联系我们找货
免费人工找货