750318961

Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: Properties Test conditions Inductance Turns Ratio L N1/ 10 kHz/ 100 mV n N1 : N2 : N3 Value Unit Tol. 66 µH min. max. 4:1:2.5 DC Resistance 1 RDC 1 N1/ 20 °C 15 mΩ DC Resistance 2 RDC 2 N2/ 20 °C 4 mΩ max. DC Resistance 3 RDC 3 N3/ 20 °C 80 mΩ ±10% 0.9 µH max. 1500 V (AC) Leakage Inductance LS 100 kHz/ 100 mV Insulation Test Voltage VT N1,3 => N2 Certification: RoHS Approval Compliant [2011/65/EU&2015/863] REACh Approval Conform or declared [(EC)1907/2006] Halogen Free Conform [JEDEC JS709B] Halogen Free Conform [IEC 61249-2-21] Schematic: 1 2 12 N1 General Information: 11 6 N2 5 3 8 N3 7 Operating Temperature -40 up to +125 °C Storage Conditions (in original packaging) < 40 °C ; < 75 % RH Storage Conditions (for single parts) -20 up to +60 °C Moisture Sensitivity Level (MSL) 1 Test conditions of Electrical Properties: +20 °C, 33 % RH if not specified differently 4 N1, N2 denotes two windings connected in parallel. Terminals 1+2, 5+6, 7+8 and 11+12 must be tied as solder bridging is allowed. Product Marking: Marking Pin 1 750318961 Lot and date code • CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE WJK 002.002 2023-04-26 ISO 2768-1m PROJECTION METHOD DESCRIPTION Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com PoE++ Power over Ethernet Plus Plus Transformer ORDER CODE 750318961 SIZE/TYPE BUSINESS UNIT STATUS PAGE EFD20 Midcom Valid 1/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Typical Application: Properties Value Version Input Voltage Unit Active Clamp Forward Vin 33 - 57 V (DC) Output Voltage 1 VOut1 5 V Output Current 1 IOut1 19 A Auxiliary Voltage Vaux 12 V Switching Frequency fswitch 200 - 300 kHz Primary: N1 Output 1: N2 Auxiliary: N3 Table shows a typical application. Values may vary by application. CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE WJK 002.002 2023-04-26 ISO 2768-1m PROJECTION METHOD DESCRIPTION Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com PoE++ Power over Ethernet Plus Plus Transformer ORDER CODE 750318961 SIZE/TYPE BUSINESS UNIT STATUS PAGE EFD20 Midcom Valid 2/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Tape: [mm] Packaging Specification - Reel: [mm] W3 A B N D W1 close to center C W2 detail B Cover Tape B Chip Cavity Sprocket Hole Embossment Tolerance Value Tape Type A0 (mm) typ. 3 20,45 B0 (mm) typ. 30,50 W (mm) ±0,3 44,00 T (mm) ±0,05 0,60 T1 (mm) ±0,0025 0,05 T2 (mm) typ. 12,70 K0 (mm) typ. 12,20 P0 (mm) ±0,1 4,00 P1 (mm) ±0,1 32,00 P2 (mm) ±0,15 2,00 D0 D0/2 (mm) (mm) +0,1/ -0,0 +0,05/-0,0 1,50 0,75 D1 (mm) min. 2,00 d (mm) ±0,05 0,20 E (mm) ±0,1 1,75 S (mm) ±0,1 40,40 F (mm) Material ±0,15 20,20 Polystyrene Qty. (pcs.) 110 Tolerance Value A (mm) max 330,00 B (mm) min. 1,50 C (mm) min. 12,80 D (mm) min. 20,20 N (mm) typ. 152,40 W1 (mm) +2,0 44,40 CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE WJK 002.002 2023-04-26 ISO 2768-1m W2 (mm) max 50,40 W3 (mm) min. 43,90 W3 (mm) max 47,40 Material PS PROJECTION METHOD DESCRIPTION Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com PoE++ Power over Ethernet Plus Plus Transformer ORDER CODE 750318961 SIZE/TYPE BUSINESS UNIT STATUS PAGE EFD20 Midcom Valid 3/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Carton: [mm] H C H IC Packaging Specification - Inner Carton: [mm] W Tolerance Value LIC (mm) typ. 361,90 WIC (mm) typ. 339,70 L IC HIC (mm) typ. 73,03 No. of Reel (pcs.) 1 IC Qty. (pcs.) 110 W Material Paper Tolerance Value LC (mm) typ. 365,12 WC (mm) typ. 342,90 L C HC (mm) typ. 230,00 C No. of Inner Carton (pcs.) Qty. (pcs.) Material 3 330 Paper CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE WJK 002.002 2023-04-26 ISO 2768-1m PROJECTION METHOD DESCRIPTION Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com PoE++ Power over Ethernet Plus Plus Transformer ORDER CODE 750318961 SIZE/TYPE BUSINESS UNIT STATUS PAGE EFD20 Midcom Valid 4/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max tL Preheat Area Ts min TC –5°C Value Preheat Temperature Min Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) 60 - 120 seconds 3 °C/ second max. Liquidous Temperature TL 217 °C Time tL maintained above TL tL 60 - 150 seconds Peak package body temperature Tp Tp ≤ Tc, see Table below Time within 5°C of actual peak temperature tp 20 - 30 seconds Ramp-down Rate (TP to TL) 6 °C/ second max. Time 25°C to peak temperature 8 minutes max. refer to IPC/ JEDEC J-STD-020E tS Package Classification Reflow Temperature (Tc): Volume mm³ 350-2000 Volume mm³ >2000 PB-Free Assembly | Package Thickness 260 °C < 1.6 mm 260 °C 260 °C PB-Free Assembly | Package Thickness 260 °C 1.6 mm - 2.5 mm 250 °C 245 °C PB-Free Assembly | Package Thickness 250 °C > 2.5 mm 245 °C 245 °C Properties 25 Time 25°C to Peak Time Volume mm³