750319948

Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: Properties 4 5,5 max. 0,51 6 1 9,45 ref. 1,22 1,82 Turns Ratio L N1+N2/ 10 kHz/ 100 mV n N1+N2 : N3+N4 Value Unit Tol. 600 µH min. 1:1.36 DC Resistance 1 RDC 1 N1+N2/ 20 °C 0.28 Ω max. RDC 2 N3+N4/ 20 °C 0.43 Ω max. 1 6 DC Resistance 2 Voltage-µSecond ∫Udt N1/ bipolar waveform 46 Vµs 3 4 Interwinding Capacitance CWW N1+N2 => N3+N4/ 100kHz/ 10mVAC/ Cs 25 pF typ. typ. 2,54 3 Test conditions Inductance 11,45 Leakage Inductance LS N1+N2/1 MHz/ 100 mV 330 nH Insulation Test Voltage VT N1,2 => N3,4 2500 V (AC) 0,3 Certification: 13,12 max. Schematic: 1 6 8,5 max. N1 5 N2 3 Compliant [2011/65/EU&2015/863] REACh Approval Conform or declared [(EC)1907/2006] Halogen Free Conform [JEDEC JS709B] Halogen Free Conform [IEC 61249-2-21] General Information: Operating Temperature N3 2 RoHS Approval N4 4 -40 up to +125 °C Storage Conditions (in original packaging) < 40 °C ; < 75 % RH Storage Conditions (for single parts) -20 up to +60 °C Moisture Sensitivity Level (MSL) 1 Electrical Specifications @ 25°C unless otherwise noted Product Marking: Pin 1 Marking • 750319948 Lot and date code CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 002.000 2023-12-12 ISO 2768-1m PROJECTION METHOD DESCRIPTION WE-PPTI Push-Pull Transformer Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750319948 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1308 Midcom Valid 1/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Typical Application: Typical Temperature Rise vs. Current Characteristics: Properties Value Unit Vin 24 V (DC) Output Voltage 1 VOut1 30 V (DC) Output Current 1 IOut1 200 mA Switching Frequency fswitch 400 - 600 kHz Input Voltage 100 90 Input: N1 / N2 Output 1: N3 / N4 Table shows a typical application. Values may vary by application. Temperature Rise [K] 80 70 60 50 40 30 0 0.2 0.4 0.6 Push-Pull Output Current [A] CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 002.000 2023-12-12 ISO 2768-1m 0.8 1 PROJECTION METHOD DESCRIPTION WE-PPTI Push-Pull Transformer Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750319948 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1308 Midcom Valid 2/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Tape: [mm] Packaging Specification - Reel: [mm] D0 A K0 P2 E1 P0 W3 T W1 close to center D A N B0 E2 W F B C Top Cover Tape A A0 P1 D1 End T2 Carrier Tape Cover Tape Start Feeding direction W2 T1 detail B B Cover Tape Chip Cavity Sprocket Hole No Component min. 160mm Components No Components min. 100mm Embossment Cover Tape min. 400mm Tape Type Tolerance Value 2a A0 (mm) typ. 8,65 B0 (mm) typ. 13,10 W (mm) +0,3/ -0,1 24,00 T (mm) ref. 0,50 T1 (mm) ref. 0,10 T2 (mm) typ. 6,00 K0 (mm) typ. 5,50 P0 (mm) ±0,1 4,00 P1 (mm) ±0,1 16,00 P2 (mm) ±0,1 2,00 D0 (mm) +0,1/ -0,0 1,50 D1 (mm) min. 1,50 E1 (mm) ±0,1 1,75 E2 (mm) min. 22,25 F (mm) ±0,1 11,50 Material Polystyrene Qty. (pcs.) 750 165° - 180° Tolerance Value A (mm) max 330,00 B (mm) min. 1,50 C (mm) min. 12,80 D (mm) min. 20,20 N (mm) typ. 101,60 W1 (mm) +2,0 24,40 CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 002.000 2023-12-12 ISO 2768-1m W2 (mm) max 30,40 W3 (mm) min. 23,90 W3 (mm) max 27,40 Material PS PROJECTION METHOD DESCRIPTION WE-PPTI Push-Pull Transformer Pull-off force Tape width 24 mm 0,1 N - 1,3 N Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750319948 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1308 Midcom Valid 3/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Outer Carton: [mm] H C H IC Packaging Specification - Inner Carton: [mm] W Tolerance Value LIC (mm) typ. 339,725 mm IC WIC (mm) typ. 361,95 mm L HIC (mm) typ. 53,975 mm No. of Plastic Box (pcs.) 1 L IC Qty. (pcs.) 750 Material Paper Tolerance Value LC (mm) typ. 365,12 mm W C WC (mm) typ. 342,90 mm HC (mm) typ. 215,90 mm C No. of Inner Carton (pcs.) Qty. (pcs.) Material 4 3000 Paper PROJECTION METHOD CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE IKK 002.000 2023-12-12 ISO 2768-1m DESCRIPTION WE-PPTI Push-Pull Transformer Wurth Electronics Midcom Inc. Headquarters 121 Airport Drive 57201 Watertown, SD United States Phone: +1 (605) 886-4385 www.we-online.com/midcom midcom@we-online.com ORDER CODE 750319948 SIZE/TYPE BUSINESS UNIT STATUS PAGE 1308 Midcom Valid 4/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max tL Preheat Area Ts min TC –5°C Value Preheat Temperature Min Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) 60 - 120 seconds 3 °C/ second max. Liquidous Temperature TL 217 °C Time tL maintained above TL tL 60 - 150 seconds Peak package body temperature Tp Tp ≤ Tc, see Table below Time within 5°C of actual peak temperature tp 20 - 30 seconds Ramp-down Rate (TP to TL) 6 °C/ second max. Time 25°C to peak temperature 8 minutes max. refer to IPC/ JEDEC J-STD-020E tS Package Classification Reflow Temperature (Tc): Volume mm³ 350-2000 Volume mm³ >2000 PB-Free Assembly | Package Thickness 260 °C < 1.6 mm 260 °C 260 °C PB-Free Assembly | Package Thickness 260 °C 1.6 mm - 2.5 mm 250 °C 245 °C PB-Free Assembly | Package Thickness 250 °C > 2.5 mm 245 °C 245 °C Properties 25 Time 25°C to Peak Time Volume mm³