850617030001

Dimensions: [mm] Recommended Hole Pattern: [mm] Electrical Properties: Of Properties P Unit Tol. C Test conditions 10 mA/ F 3 F +30%/-10% Rated Voltage VR @ 65 °C 2.7 V (DC) max. Rated Voltage VR @ 85 °C 2.3 V (DC) max. Surge Voltage VS @ 65 °C 2.85 V (DC) max. 70 mΩ max. ESR RESR DC 10 ms ESR RESR AC 5 mV @ 1 kHz 60 mΩ max. Rated Discharge Current IRated 0.7 A typ. Max. Discharge Current IMax 3.3 A typ. Leakage Current ILeak 0.008 mA typ. Power Density P 18.08 kW/ kg typ. Energy Density E 2.1 Wh/ kg typ. 15,0 min. 4,0 min. L p Value Capacitance 72 hrs. @ VR Schematic: - General Information: + OF Vent Storage Conditions (in original packaging) 15 °C up to + 35 °C; 10 % up to 75 % RH Operating Temperature -40 up to +65 °C Moisture Sensitivity Level (MSL) 1 OD Life Cycle Weight m 500000 Cycles 1.4 g Test conditions of Electrical Properties: +20 °C, 35 % RH if not specified differently Component conform to REACh and RoHS requirements and standards Dimensions: Properties Value Unit Tol. ØD 8 mm ±1.5 Length L 20 mm ±1.5 Pitch P 3.5 mm ±0.5 ØF 0.6 mm ±0.02 Pitch p 3.5 mm Hole Diameter Øf 0.9 mm ±0.02 Diameter Pin Diameter ±0.5 Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE ReKa 002.002 2022-04-11 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-STSC Supercapacitors (EDLC‘s) STP0820305Q2R7DSPB15000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 8.0 x 20.0 eiCap Valid 1/10 ORDER CODE 850617030001 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Component Marking: 2nd Additional Information: Horizontal Line Supercapacitor 3rd Horizontal Line EDLC Energy Capacity: 0.003 Wh 3rd Line 5th Properties Description Formula Max. Discharge Current Imax – [A] Current to discharge from V R to V R/2 within 1 sec. Rated Discharge Current IRated – [A] Current to discharge from V R to V R/2 within 5 sec. Leakage Current ILeak – [mA] is measured at 25°C (after holding 72 h at V R) Power Density P – [W/kg] impedance matched with m (kg) as net weight for Capacitor 𝑃𝑚𝑎𝑥 = Energy Density E – [Wh/kg] with m(kg) as net weight for Capacitor 𝐸= ESR RESR – [mΩ] RESR AC: measured by contact resistance meter, conditions: Amplitude: 5 mV Frequency 1 kHz RESR DC: Measured by constant current discharge method (i.a.w. IEC62391), deltaV: Voltage drop during