875036319018

Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: - 2,8 + 2,4 ±0,1 Properties 1,3 ±0,3 1,3 ±0,3 1,9 ±0,1 4,0 Test conditions Capacitance C Rated Voltage VR Surge Voltage VS 0.5 V/ 120 Hz/ +20 °C 1000 cycles @ 20 °C Leakage Current ILeak 2 min./ +20 °C Dissipation Factor DF 0.5 V/ 120 Hz/ +20 °C Ripple Current IRIPPLE 100 kHz @ 45 °C ESR RESR 100 kHz @ 20°C Value Unit Tol. 470 µF ±20% 2.5 V (DC) max. 3.1 V (DC) max. 117.5 µA max. 6 % max. 8500 mA max. 4.5 mΩ max. 2,4 8,8 Scale - 5:1 Schematic: 7,3 ±0,2 General Information: Aluminum Polymer Capacitors - + 4,3 ±0,2 Polarity Mark (Positive) Storage Conditions (in original packaging) 5 °C up to + 30 °C; 10 % up to 70 % RH Operating Temperature -55 up to +105 °C Endurance 2000 h Moisture Sensitivity Level (MSL) 3 Test conditions of Electrical Properties: +20 °C, 35 % RH if not specified differently FIT according to separate documentation Surge Voltage: Charging time 30s, discharging time 330s for a cycle Scale - 5:1 Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE PSL 003.000 2021-06-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PHLE Aluminum Polymer Capacitors PSE2917471M2R5DH1T2HT19 SIZE/TYPE BUSINESS UNIT STATUS PAGE 7.3 x 4.3 x 1.9 eiCap Valid 1/9 ORDER CODE 875036319018 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Component Marking: 1st Line left WE Marking 1st Line right Capacitance Value 470 µF (Coding 470 ) 2nd Line left Lot Number 2nd Line right Rated Voltage: 2.5 V (DC) (Coding e ) Multiplier for Ripple Current vs. Frequency Frequency Multiplier 100 Hz ≤ freq. < 1 kHz 0.05 1 kHz ≤ freq. < 10 kHz 0.3 10 kHz ≤ freq. < 20 kHz 0.6 20 kHz ≤ freq. < 50 kHz 0.7 50 kHz ≤ freq. < 100 kHz 0.8 100 kHz ≤ freq. < 200 kHz 1.0 200 kHz ≤ freq. < 500 kHz 0.8 500 kHz ≤ freq. < 1 MHz 0.7 1 MHz ≤ freq. < 10 MHz 0.4 Multiplier for Ripple Current vs. Temperature Temperature Multiplier for 2 V(DC) up to 6.3 V(DC) Multiplier for 10 V(DC) up to 35 V(DC) T ≤ 45°C 1.0 1.0 45°C < T ≤ 85 °C 0.7 0.8 85°C < T ≤ 105 °C 0.25 0.5 105°C < T ≤ 125 °C 0.25 (WCAP-PHET) Certification: RoHS Approval Compliant [2011/65/EU&2015/863] REACh Approval Conform or declared [(EC)1907/2006] Halogen Free Conform [JEDEC JS709B] Halogen Free Conform [IEC 61249-2-21] Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE PSL 003.000 2021-06-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PHLE Aluminum Polymer Capacitors PSE2917471M2R5DH1T2HT19 SIZE/TYPE BUSINESS UNIT STATUS PAGE 7.3 x 4.3 x 1.9 eiCap Valid 2/9 ORDER CODE 875036319018 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Tape: [mm] Packaging Specification - Reel: [mm] P0 A P2 W3 T E1 D0 K0 A W C D B0 E2 B N F W1 close to center Top Cover Tape A0 A W2 T1 P1 T2 End Start Feeding direction Carrier Tape detail B Cover Tape B Cover Tape Chip Cavity Sprocket Hole No Component min.160mm Components No Component min.100mm Embossment Cover Tape min. 400mm Packaging is referred to the international standard IEC 60286-3:2019 Tape Type 2a A0 (mm) typ. 4,50 B0 (mm) typ. 7,60 W (mm) +0,3/ -0,1 12,00 T (mm) typ. 0,30 T1 (mm) typ. 0,05 T2 (mm) typ. 2,55 K0 (mm) typ. 2,40 P0 (mm) ±0,1 4,00 P1 (mm) ±0,1 8,00 P2 (mm) ±0,05 2,00 D0 (mm) +0,1/ -0,0 1,50 E1 (mm) ±0,1 1,75 E2 (mm) min. 10,25 F (mm) ±0,05 5,50 Material Qty. (pcs.) Polystyrene 3500 165° - 180° Pull-of force Tape width 12 mm 0,1 N - 1,3 N Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com Tolerance Value A (mm) ± 2,0 330,00 B (mm) min. 1,50 C (mm) min. 12,80 D (mm) min. 20,20 N (mm) typ. 80,00 W1 (mm) + 2,0 12,40 W2 (mm) max. 18,40 CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE PSL 003.000 2021-06-14 DIN ISO 2768-1m W3 (mm) min. 11,90 W3 (mm) max. 15,40 Material Polystyrene PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PHLE Aluminum Polymer Capacitors PSE2917471M2R5DH1T2HT19 SIZE/TYPE BUSINESS UNIT STATUS PAGE 7.3 x 4.3 x 1.9 eiCap Valid 3/9 ORDER CODE 875036319018 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Outer Carton: [mm] H H C IC Packaging Specification - Reel in Carton: [mm] W C C L W L IC Tolerance Value LIC (mm) typ. 360,00 WIC (mm) typ. 360,00 HIC (mm) typ. 130,00 No. of reel (pcs.) 5 IC Qty. (pcs.) 17500 Material Paper Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com Tolerance Value LC (mm) typ. 370,00 WC (mm) typ. 370,00 HC (mm) typ. 140,00 No. of Inner Carton (pcs.) Qty. (pcs.) Material 1 17500 Paper CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE PSL 003.000 2021-06-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PHLE Aluminum Polymer Capacitors PSE2917471M2R5DH1T2HT19 SIZE/TYPE BUSINESS UNIT STATUS PAGE 7.3 x 4.3 x 1.9 eiCap Valid 4/9 ORDER CODE 875036319018 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max tL Preheat Area Ts min TC –5°C Value Preheat Temperature Min Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) 60 - 120 seconds 3 °C/ second max. Liquidous Temperature TL 217 °C Time tL maintained above TL tL 60 - 150 seconds Peak package body temperature Tp Tp ≤ Tc, see Table below Time within 5°C of actual peak temperature tp 20 - 30 seconds Ramp-down Rate (TP to TL) 6 °C/ second max. Time 25°C to peak temperature 8 minutes max. refer to IPC/ JEDEC J-STD-020E tS Package Classification Reflow Temperature (Tc): Volume mm³ 350-2000 Volume mm³ >2000 PB-Free Assembly | Package Thickness 260 °C < 1.6 mm 260 °C 260 °C PB-Free Assembly | Package Thickness 260 °C 1.6 mm - 2.5 mm 250 °C 245 °C PB-Free Assembly | Package Thickness 250 °C > 2.5 mm 245 °C 245 °C Properties 25 Time 25°C to Peak Time Volume mm³