875075761007

Dimensions: [mm] Recommended Land Pattern: [mm] Electrical Properties: + 0,35 -0,05 1,9 - 0,9 ±0,2 Properties 4,5 ±0,2 4,3 Test conditions Capacitance C Rated Voltage VR Surge Voltage VS 0.25 V/ 120 Hz/ +20 °C Value Unit Tol. 68 µF ±20% 50 V (DC) max. 1000 cycles @ 20 °C 57.5 V (DC) max. Leakage Current ILeak 2 min./ +20 °C 680 µA max. Dissipation Factor DF 0.25 V/ 120 Hz/ +20 °C 12 % max. 2000 mA max. 35 mΩ max. Ripple Current IRIPPLE 100 kHz @ 105 °C ESR RESR 0.25 V/ 100 kHz/ +20 °C 4,4 12,4 ±0,3 0,3 max. O 10,0 ±0,5 Schematic: General Information: q 10,3 ±0,2 Aluminum Polymer Capacitors Operating Temperature -55 up to +105 °C Storage Conditions (in original packaging) 5 °C up to + 35 °C; 10 % up to 75 % RH Endurance 2000 h Moisture Sensitivity Level (MSL) 1 Test conditions of electrical properties: +20 °C, 35 % RH if not specified differently FIT according to separate documentation Surge Voltage: charging time 30 s, discharging time 330 s for a cycle Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE FPu 002.000 2022-09-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PSLC Aluminum Polymer Capacitors PSEF124680M050DVCTFB000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 10.0 x 12.4 eiCap Valid 1/9 ORDER CODE 875075761007 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Component Marking: 1st Line Capacitance Value: 68 µF ( Coding: 680 ) 2nd Line WCAP-PSLC & datecode: YWW 3rd Line Rated Voltage:50 V(DC) Multiplier for Ripple Current vs. Frequency Frequency 120 Hz ≤ freq. < 1 kHz 1 kHz ≤ freq. < 10 kHz 10 kHz ≤ freq. < 100 kHz 100 kHz ≤ freq. < 300 kHz Muliplier 0.05 0.3 0.7 1.0 Lifetime Performance: Test Conditions Endurance Moisture Resistance Lifetime 2000 h @ 105 °C 1000 h, stored @ 60 °C , RH 90~95 % Voltage UR applied None Current None None ∆C ≤ ±20 % of initial measured value ≤ ±20 % of initial measured value ESR ≤ 150 % of the initial specified value ≤ 150 % of the initial specified value DF ≤ 150 % of the initial specified value ≤ 150 % of the initial specified value Leakage Current ≤ the initial specified value ≤ the initial specified value Certification: RoHS Approval Compliant [2011/65/EU&2015/863] REACh Approval Conform or declared [(EC)1907/2006] Halogen Free Conform [JEDEC JS709B] Halogen Free Conform [IEC 61249-2-21] Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE FPu 002.000 2022-09-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PSLC Aluminum Polymer Capacitors PSEF124680M050DVCTFB000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 10.0 x 12.4 eiCap Valid 2/9 ORDER CODE 875075761007 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Tape: [mm] Packaging Specification - Reel: [mm] P0 P2 W3 T E1 D0 A N W B D B0 E2 F W1 close to center C Top Cover Tape A0 P1 K0 T1 W2 T2 End Start Feeding direction Carrier Tape detail B Cover Tape Cover Tape Chip Cavity B No Component min. 160mm Components No Component min. 100mm Sprocket Hole Embossment Cover Tape min. 400mm Tape Type Tolerance Value 2a A0 (mm) ±0,2 10,70 B0 (mm) ±0,2 10,70 W (mm) ±0,3 24,00 T (mm) ±0,05 0,40 T1 (mm) max. 0,10 T2 (mm) ±0,2 12,90 K0 (mm) typ. 12,74 P0 (mm) ±0,1 4,00 P1 (mm) ±0,1 16,00 P2 (mm) ±0,05 2,00 D0 (mm) ±0,1 1,50 E1 (mm) ±0,1 1,75 E2 (mm) min. 22,25 F (mm) ±0,1 11,50 Material Polystyrene Qty. (pcs.) 400 165° - 180° Pull-off force Tape width 24 mm 0,1 N - 1,3 N Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com Tolerance Value A (mm) ± 2,0 380 B (mm) ± 0,5 2 C (mm) ± 0,5 15 D (mm) ± 0,8 21 N (mm) min. 80 W1 (mm) ± 1,0 26 CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE FPu 002.000 2022-09-14 DIN ISO 2768-1m W2 (mm) ± 1,0 32 W3 (mm) ± 1,0 26 Material Paper PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PSLC Aluminum Polymer Capacitors PSEF124680M050DVCTFB000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 10.0 x 12.4 eiCap Valid 3/9 ORDER CODE 875075761007 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Inner Carton: [mm] Packaging Specification - Outer Carton: [mm] W H C H IC IC L IC W L C Tolerance Value LIC (mm) typ. 400,00 WIC (mm) typ. 390,00 HIC (mm) typ. 106,00 No. of Reel (pcs.) 3 Qty. (pcs.) 1200 Material Paper Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com Tolerance Value LC (mm) typ. 425,00 WC (mm) typ. 412,00 HC (mm) typ. 340,00 C No. of Inner Carton (pcs.) Qty. (pcs.) Material 3 3600 Paper CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE FPu 002.000 2022-09-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PSLC Aluminum Polymer Capacitors PSEF124680M050DVCTFB000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 10.0 x 12.4 eiCap Valid 4/9 ORDER CODE 875075761007 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Classification Reflow Profile for SMT components: Classification Reflow Soldering Profile: Profile Feature Tp tp Max. Ramp Up Rate Max. Ramp Down Rate TL Temperature Ts max tL Preheat Area Ts min TC –5°C Value Preheat Temperature Min Ts min 150 °C Preheat Temperature Max Ts max 200 °C Preheat Time ts from Ts min to Ts max ts Ramp-up Rate (TL to TP) 60 - 120 seconds 3 °C/ second max. Liquidous Temperature TL 217 °C Time tL maintained above TL tL 60 - 150 seconds Peak package body temperature Tp Tp ≤ Tc, see Table below Time within 5°C of actual peak temperature tp 20 - 30 seconds Ramp-down Rate (TP to TL) 6 °C/ second max. Time 25°C to peak temperature 8 minutes max. refer to IPC/ JEDEC J-STD-020E tS Package Classification Reflow Temperature (Tc): Volume mm³ 350-2000 Volume mm³ >2000 PB-Free Assembly | Package Thickness 260 °C < 1.6 mm 260 °C 260 °C PB-Free Assembly | Package Thickness 260 °C 1.6 mm - 2.5 mm 250 °C 245 °C PB-Free Assembly | Package Thickness 250 °C > 2.5 mm 245 °C 245 °C Properties 25 Time 25°C to Peak Time Volume mm³ 360°C). Do not wash the assembled capacitors with the following cleaning agents: Operation and usage of the capacitor • Petroleum system solvents: may cause degeneration of the rubber seal material • Alkali system solvents: may cause corrosion and dissolve of the aluminum case • Halogenated solvents: may cause corrosion and failure of the capacitor • Acetone: component marking may be erased • Xylene: may cause deterioration of the rubber seal material Verify the following points when washing is applied to capacitors: • Please monitor conductivity, pH-value, specific gravity and the water content of cleaning agents. Contamination adversely affects these characteristics. • Be sure to not expose the capacitors under solvent rich conditions or keep capacitors inside a closed container. In addition, please dry the solvents on the PCB and the capacitor sufficiently with an air knife (temperature should be less than the maximum rated category temperature of the capacitor) for 10 minutes. • Capacitors can be characteristically and catastrophically damaged by halogen ions, particularly by chlorine ions. The degree of the damage mainly depends upon the characteristics of the electrolyte and rubber seal material. When halogen ions come into contact with the inside of the capacitors, the foil may corrode, when a voltage is applied. This corrosion causes an extremely high leakage current, which results in venting and an open circuit defect. All other cleaning processes and cleaning agents are not approved by Würth Elektronik. All cleaning methods need to be tested and validated by the customer. In operation and usage, take care about the following points.Do not use the capacitor within the following environmental conditions: • • • • • • Environment with high mechanical stress / shocks or vibration (please see this specific datasheet for permitted limits). Environment with high amount of damp condensation, water or types of oil. Direct sunlight, ozone, any kind of radiation or ultraviolet rays. Toxic gases (e.g. ammonium, chlorine and compounds, bromine and compounds, hydrogen sulfide, sulfuric acid). User should never touch the terminals of the capacitor directly. Avoid short circuit between terminals with any kind of conductive material (e.g. metal, fluid, acid, alkaline solution). Maintenance For industrial applications, it is recommended to perform periodic inspections. Power supplies shall be turned off before inspection to discharge the capacitor. Check the following points in case of an inspection: • Visual inspection of the capacitor to see, if the vent operated for pressure relief and if any leakage of electrolyte has taken place. • Measurement of electrical characteristics of the capacitor (according to datasheet, especially leakage current, capacitance and dissipation factor). In case of deviation or failure according to the specified characteristics, take care to start appropriate actions (e.g. replacement of capacitor). Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE FPu 002.000 2022-09-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PSLC Aluminum Polymer Capacitors PSEF124680M050DVCTFB000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 10.0 x 12.4 eiCap Valid 7/9 ORDER CODE 875075761007 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Emergency case • In case of excessive pressure within the capacitor, the vent may operate and release this pressure. In case of vent operation, gas becomes visible when the component is in operation. If so, directly turn off the application and disconnect it from the power source. If the application is not turned off, a possible short circuit of capacitor or a short circuit due to bridging of liquefied gas can possibly damage the circuit and, in worst case, the application may be dramatically damaged. Do not stay or position body or face above or in direction of the vent, because in the event of any vent operation, the releasing gas temperature may have over 100 °C. In case the electrolyte gets in contact with skin, wash the skin immediately with plenty of soap and water. If the released gas gets in contact with eyes, rinse immediately with plenty of water and seek medical advice. In case the gas was inhaled, gargle immediately with plenty of water and seek medical advice. Additional requirements for aluminum polymer capacitors Circuits and designs where the usage of aluminum polymer capacitors is prohibited are: • a) High-impedance circuits • b) Coupling circuits • c) Time constant circuits Due to thermal stress, the leakage of aluminum polymer capacitor can vary within the above stated applications. If you want to use two or more aluminum polymer capacitors in series connection for circuit designs, which are significantly affected by leakage current, please contact our technical staff before usage. Disposal • Please contact your local responsible or organization for proper disposal of capacitor. In addition, take care to be compliant with your local governmental law and restrictions. In case of incineration, it should be done with more than 800 °C. Lower temperatures of incineration can result in toxic gases (e.g. chlorine). To avoid any explosion of capacitor, punch holes into the can or crush the capacitor before incineration. These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable. However, no responsibility is assumed for inaccuracies or incompleteness. Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE FPu 002.000 2022-09-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PSLC Aluminum Polymer Capacitors PSEF124680M050DVCTFB000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 10.0 x 12.4 eiCap Valid 8/9 ORDER CODE 875075761007 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Important Notes 6. Product Life Cycle The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG: Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 1. General Customer Responsibility Some goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not. 2. Customer Responsibility related to Specific, in particular Safety-Relevant Applications It has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications. In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at www.we-online.com. 7. Property Rights All the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used. 8. General Terms and Conditions Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at www.we-online.com. 3. Best Care and Attention Any product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty. 4. Customer Support for Product Specifications Some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter. 5. Product R&D Due to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected. Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE FPu 002.000 2022-09-14 DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-PSLC Aluminum Polymer Capacitors PSEF124680M050DVCTFB000 SIZE/TYPE BUSINESS UNIT STATUS PAGE 10.0 x 12.4 eiCap Valid 9/9 ORDER CODE 875075761007 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.