885012208018

A Dimensions: [mm] B Recommended land pattern: [mm] D1 Electrical Properties: Properties Test conditions Capacitance 1±0.2 Vrms, 1 kHz ±10% Rated voltage Value Unit Tol. C 10000000 pF ± 10% UR 10 V (DC) max. Dissipation factor 1±0.2 Vrms, 1 kHz ±10% DF ≤ 10% Isolation Resistance Apply UR for 120 s max. RIso ≥ 0.01 typ. GΩ Precondition for Class II MLCC measurement: Apply a preheat treatment @150±10°C for 1 hour. The measurement should be applied after 24±2 hrs the part was stored under ambient conditions. There is not any precondition necessary for Class I MLCC. C Schematic: E General information: General Purpose MLCC Ceramic Type: Temperature Coeffecient: Storage Conditions: Operating Temperature: Dielectric Strength: General Test conditions: FIT according to X7R Class II ± 15% max. 35°C, 0603 10 ±1 sec; 10N all 3 directions, 2 hours each @ 10 - 55 - 10 Hz, amplitude 0.75 mm or 10 g Vibration Resistance Resistance to Solder Heat Solder Temperature 260°C ±5°C Dipping Time 10 ±1 sec Specific Refer to Soldering Profile DESCRIPTION WCAP-CSGP Ceramic Capacitors 1.0 2014-11-06 SSt PSL REV DATE BY CHECKED Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com Order.- No. 885012208018 SIZE A4 Size: 1206 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. H Soldering Specifications: H2: Classification Reflow Profiles H1: Classification Reflow Profile for SMT components: Profile Feature Pb-Free Assembly Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (ts) from (Tsmin to Tsmax) 150°C 200°C 60-120 seconds Ramp-up rate (TL to TP) 3°C/ second max. Liquidous temperature (TL) Time (tL) maintained above TL 217°C 60-150 seconds Peak package body temperature (Tp) See Table H3 Time within 5°C of actual peak temperature (tp) 20-30 seconds Ramp-down rate (TP to TL) 6°C/ second max. Time 25°C to peak temperature 8 minutes max. refer to IPC/JEDEC J-STD-020D H3: Package Classification Reflow Temperature Package Thickness Volume mm³ 2000 PB-Free Assembly < 1.6 mm 260°C 260°C 260°C PB-Free Assembly 1.6 - 2.5 mm 260°C 250°C 245°C PB-Free Assembly ≥ 2.5 mm 250°C 245°C 245°C refer to IPC/JEDEC J-STD-020D DESCRIPTION WCAP-CSGP Ceramic Capacitors 1.0 2014-11-06 SSt PSL REV DATE BY CHECKED Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 www.we-online.com eiSos@we-online.com Order.- No. 885012208018 SIZE A4 Size: 1206 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. I Cautions and Warnings: The following conditions apply to all goods within the product series of WCAP-CSGP of Würth Elektronik eiSos GmbH & Co. KG: 1. General •The capacitor is engineered, designed and manufactured to be used within the datasheet specified values. •Do not use the capacitor neither short term nor long term outside the specified values, which are given in the data sheet. •Do not apply any kind of flexural or compressive force onto soldered or unsoldered component. •Prevent the capacitor surface from any damage or scratches with sharp edges (e.g. chassis, screwdrivers, pincers) •Operating voltage across the terminals including AC and DC peaks and AC or pulse overshooting, Vp-p as well as irregular voltage because of resonance or switching must be below the rated voltage. •Due to self-heating the reliability of the capacitor may be reduced, if high frequency AC or pulse is applied. •Avoid any overload or conditions that are not specified in the capacitors datasheet. •Consider carefully possible specific changes of electrical characteristics like capacitance over temperature, voltage and time as well as the specific performance over frequency for the actual use conditions. For detailed information see datasheet. 2. Product specific The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply to customer specific products. Follow all instructions mentioned in the data sheet, especially the following items: 2.1 Storage conditions •These ceramic capacitors must be stored in stable conditions within an ambient temperature between 5°C to 40°C with a relative humidity of 150°C ΔT ≤ 190°C Room air 1210 or more 280°C max >150°C ΔT ≤ 130°C Room air •Typical time of actual peak temperature: