Dimensions: [mm]
Recommended Land Pattern: [mm]
Electrical Properties:
Properties
Test conditions
Capacitance
5,4
Rated Voltage
3,3
2,3
0,5 ±0,25
C
1 ±0.2 VRMS, 1 MHz ±10%
@25 °C
Value
Unit
Tol.
33
pF
±5%
VR
250
V (AC) max.
Impulse Voltage
VIMP
2500
V (DC) max.
Dissipation Factor
DF
Insulation Resistance
RISO Apply 500 V for 60 s max.
1 ±0.2 VRMS, 1 MHz ±10%
@25 °C
0.1
%
max.
100
GΩ
min.
Dielectric Strength
X-Cap: 1075 V (DC) 60s @ dV ≤ 150 V (r.m.s)/ sec.
Y-Cap: 1500 V (AC) 60s @ dV ≤ 150 V (r.m.s)/ sec.
Charge & Discharge Current < 50 mA
4,5
+0,5
-0,3
Precondition for Class II MLCC measurement: Apply a preheat treatment @150 ±10 °C for 1 hour.
The measurement should be applied after 24 ±2 hrs the part was stored under ambient conditions.
There is not any precondition necessary for Class I MLCC.
1,4 ±0,15
Schematic:
General Information:
Safety Certified MLCC
3,5 min.
Ceramic Type
NP0 Class I
2,0 ±0,25
Safety Class
X2
Temperature Coefficient
± 30 ppm/ °C max.
Operating Temperature
-55 up to +125 °C
Storage Conditions
(in original packaging)
5 °C - 35 °C; 10 % up to 75 % RH
Moisture Sensitivity Level (MSL)
1
Test conditions of Electrical Properties: +20 °C, 35 % RH if not specified differently
FIT according to separate documentation
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
AMM
001.000
2020-03-04
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-CSSA Ceramic Capacitors
NP01808330JB50IFCT1B000
ORDER CODE
8853620100091
SIZE/TYPE
BUSINESS UNIT
STATUS
PAGE
1808
eiCap
Valid
1/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Mechanical Properties:
Properties
Definition
Termination
Cu/ Ni/ Sn
Adhesice Strength of Termination all sizes
10 ±1 sec; 10 N
Vibration Resistance
all 3 directions, 2 hours each @ 10 - 55 Hz/
min., amplitude 0.75 mm or 10 g
Resistance to Solder Heat
Specific
Refer to Soldering Profile
Certification:
RoHS Approval
Compliant [ 2011/65/EU&2015/863 ]
REACh Approval
Conform or declared [ (EC)1907/2006 ]
Halogen Free
Conform [ JEDEC JS709B ]
Halogen Free
Conform [ IEC 61249-2-21 ]
TUEV Approval
R50268363
cULus Approval
E345659 [ UL-60384-14 ]
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
AMM
001.000
2020-03-04
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-CSSA Ceramic Capacitors
NP01808330JB50IFCT1B000
ORDER CODE
8853620100091
SIZE/TYPE
BUSINESS UNIT
STATUS
PAGE
1808
eiCap
Valid
2/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Packaging Specification - Tape and Reel: [mm]
P0
A
K0
P2
W3
T
W1
close to center
A
W
F
N
B
D
E1
D0
B0
E2
C
Top Cover
Tape
D1
A
P1
W2
T1
A0
T2
End
Feeding direction
Start
detail B
Carrier Tape
B
Cover Tape
Cover Tape
Chip Cavity
Sprocket Hole
No Component
min.160mm
Components
No Component
min.100mm
Embossment
Cover Tape
min. 400mm
Tape Type
2a
A0
(mm)
typ.
2,50
B0
(mm)
typ.
5,30
W
(mm)
+0,3/ -0,1
12,00
T
(mm)
ref.
0,25
T1
(mm)
ref.
0,10
T2
(mm)
typ.
2,91
K0
(mm)
typ.
2,50
P0
(mm)
±0,1
4,00
P1
(mm)
±0,1
4,00
P2
(mm)
±0,05
2,00
D0
(mm)
+0,1/ -0,0
1,50
D1
(mm)
min.
1,50
E1
(mm)
±0,1
1,75
E2
(mm)
min.
10,25
F
(mm)
±0,05
5,50
Material
Qty.
(pcs.)
Polycarbonate
2000
165° - 180°
Pull-of force
Tape width
12 mm
0,1 N - 1,3 N
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
A
(mm)
± 2,0
178,00
B
(mm)
min.
1,50
C
(mm)
min.
12,80
D
(mm)
min.
20,20
N
(mm)
min.
50,00
W1
(mm)
+ 2,0
12,40
W2
(mm)
max.
18,40
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
AMM
001.000
2020-03-04
DIN ISO 2768-1m
W3
(mm)
min.
11,90
W3
(mm)
max.
15,40
Material
Polystyrene
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-CSSA Ceramic Capacitors
NP01808330JB50IFCT1B000
ORDER CODE
8853620100091
SIZE/TYPE
BUSINESS UNIT
STATUS
PAGE
1808
eiCap
Valid
3/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
H
IC
H
C
Packaging Specification - Reel in Carton: [mm]
W
C
L
C
W
IC
L
LIC
(mm)
typ.
120,00
WIC
(mm)
typ.
180,00
HIC
(mm)
typ.
180,00
IC
No. of
Reel (pcs.)
Qty.
(pcs.)
Material
8
16000
Paper
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
www.we-online.com
eiSos@we-online.com
LC
(mm)
typ.
393,00
WC
(mm)
typ.
393,00
HC
(mm)
typ.
203,00
No. of
Inner Carton (pcs.)
Qty.
(pcs.)
Material
6
96000
Paper
CHECKED
REVISION
DATE (YYYY-MM-DD)
GENERAL TOLERANCE
AMM
001.000
2020-03-04
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-CSSA Ceramic Capacitors
NP01808330JB50IFCT1B000
ORDER CODE
8853620100091
SIZE/TYPE
BUSINESS UNIT
STATUS
PAGE
1808
eiCap
Valid
4/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Classification Reflow Profile for SMT components:
Classification Reflow Soldering Profile:
Profile Feature
Tp
tp
Max. Ramp Up Rate
Max. Ramp Down Rate
TL
Temperature
Ts max
Ts min
Ts min 150 °C
Preheat Temperature Max
Ts max 200 °C
Preheat Time ts from Ts min to Ts max
ts
Ramp-up Rate (TL to TP)
Liquidous Temperature
tL
Preheat Area
TC –5°C
Value
Preheat Temperature Min
60 - 120 seconds
3 °C/ second max.
TL
217 °C
Time tL maintained above TL
tL
60 - 150 seconds
Peak package body temperature
Tp
see table
Time within 5°C of actual peak
temperature
tp
20 - 30 seconds
Ramp-down Rate (TL to TP)
6 °C/ second max.
Time 25°C to peak temperature
8 minutes max.
refer to IPC/ JEDEC J-STD-020E
tS
Package Classification Reflow Temperature:
Volume mm³
350-2000
Volume mm³
>2000
PB-Free Assembly | Package Thickness 260 °C
< 1.6 mm
260 °C
260 °C
PB-Free Assembly | Package Thickness 260 °C
1.6 mm - 2.5 mm
250 °C
245 °C
PB-Free Assembly | Package Thickness 250 °C
≥ 2.5 mm
245 °C
245 °C
Properties
25
Time 25°C to Peak
Time
Volume mm³
