Dimensions: [mm]
Recommended Hole Pattern: [mm]
Electrical Properties:
Properties
Test conditions
Capacitance
1 V/ 1 kHz ± 0.2 kHz
Rated Voltage
Of
OF
Rated Voltage
P
p
Unit
Tol.
39
nF
±10%
UR
275
V (AC)
max.
max.
UR
630
V (DC)
Insulation Resistance
1 min @ 100 V (DC)
RISO
30000
MΩ
min.
Dissipation Factor
@ 1 kHz
DF
0.1
%
max.
Dissipation Factor
@ 10 kHz
DF
0.1
%
max.
Dissipation Factor
@ 100 kHz
DF
0.5
%
max.
dV/dt
300
V/µs
max.
Rate of Voltage Rise
H
L
Value
C
Dielectric Strength Pin to
Pin
1 min./ +20 °C
1333
V (DC)
Dielectric Strength Pin to
Case
1 min./ +20 °C
2000
V (AC)
G
Schematic:
General Information:
X2-Safety Class Capacitor; MKP - Metallized Polypropylene
Storage Conditions
5-35 °C, < 75% RH
Operating Temperature
-40 °C up to +105 °C
Maxium Selfheating (Rated)
7
°C
W
Climate Category: 40/ 105/ 56/ B
Test conditions of Electrical Properties: +20 °C, 35 % RH if not specified differently
FIT according to separate documentation
Component conform to REACh and RoHS requirements and standards
Only designed to be used in parallel to the mains, not approved for series applications.
Properties
Value
Unit
Tol.
Pitch
P
15
mm
±0.5
Length
L
18
mm
±0.5
Width
W
5
mm
±0.5
Height
H
11
mm
±0.5
Pin length
G
4
mm
±0.5
ØF
0.8
mm ±0.05
Pitch
p
15
mm
Hole Diameter
Øf
1.1
mm
Pin Diameter
±0.5
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
1/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Product Marking:
1st
Line right
Matchcode: FTX2
2nd Line right
Rated Voltage: 275 V~
3rd Line right
Climate Category: 40/ 105/ 56/ B
2nd
Line left
Capacitance & Tolerance Code: 393K (Basis pF)
Bottom Line
Certificates: ENEC, cULUS, CQC & Internal Marking
Top Cover Marking P < 15
Date Code: YWW
Top Cover Marking P ≥ 15
Date Code & Capacitance & Tolerance Code
Damp Heat
IEC 60068 - 2 - 78
40°C, 95% RH, 56 days
Temperature
Cycles
IEC 60068 - 2 - 14
5 cycles, upper and lower temperature 30 min. each, 30 sec. transfer
time
Charge/
Discharge Test
IEC 60384 - 14
√2 x UR @ 100 V/μs
Surge Test
IEC 60384 - 14
2.5 kV Surge impulses
Certification:
Properties
Standard
File
ENEC10 by VDE
IEC 60384-14
40038405
cULus
UL 60384-14 / CAN/CSA - E60384-14
E345659
CQC
IEC 60384-14
13001104051
Mechanical Properties:
Properties
Test Conditions
Lead Diameter [mm] Force [N]
condition
Termination Robustness
IEC 600668 - 2 - 21 Pull Test
0.5 to ≤ 0.8
10
min. 10 sec.
0.9 to ≤ 1.25
20
min. 10 sec.
0.5 to ≤ 0.8
5
min. 2 cycles
0.9 to ≤ 1.25
10
min. 2 cycles
Bend Test
Environmental Tests:
Properties
Standard
Active
Flammability
IEC 60384-14
max. 24 surge pulses @ 2.5 kV (one pulse every 5 seconds)
Passive
Flammability
IEC 60384-14
in combination with IEC 60381 - 1 & IEC 60695 - 11 - 5
Vibration
IEC 60068 - 2 - 6
all 3 directions, 2 hours each @ 10 - 55 - 10 Hz, amplitude 0.75 mm or
10 g
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
2/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Capacitance Change vs. Frequency:
Dissipation Factor vs. Frequency:
0.50
1.000
0.30
Dissipation Factor [%]
Capacitance Change [%]
0.10
-0.10
-0.30
-0.50
0.100
-0.70
-0.90
-1.10
0.010
1.0
10.0
100.0
1.0
10.0
Frequency [kHz]
100.0
1000.0
Frequency [kHz]
Test Equipment: E4991A or equivalent
Test Equipment: E4991A or equivalent
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
3/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Dissipation Factor vs. Temperature:
6.0
1.20
4.0
1.00
2.0
0.80
Dissipation Factor [%]
Capacitance Change [%]
Capacitance Change vs. Temperature:
0.0
0.60
-2.0
0.40
-4.0
0.20
-6.0
0.00
-50 -40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110
-50 -40 -30 -20 -10 0
10 20 30 40 50 60 70 80 90 100 110 120
Temperature [°C]
Temperature [°C]
Test Equipment: E4991A or equivalent
Test Equipment: E4991A or equivalent
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
4/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Packaging Specification - Carton: [mm]
L
H
H
C
IC
Paperboard
IC
L
W
W
C
C
IC
LIC (mm)
WIC (mm)
HIC (mm)
typ.
275,00
typ.
160,00
typ.
95,00
No. of
Paperboard
pcs.
5
No. of
Layer
pcs.
4
Packaging
Unit
pcs.
1696
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
Material
LC (mm)
WC (mm)
HC (mm)
typ.
500,00
typ.
290,00
typ.
240,00
No. of
inner Carton
pcs.
6
Packaging
Unit
pcs.
10176
Material
Paper
Paper
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
5/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Classification Wave Soldering Profile:
Classification Wave Soldering Profile:
Profile Feature
tp
Tp
Preheat Temperature Min
Preheat Temperature Typical
First Wave
Second Wave
Preheat Temperature Max
Sn-Pb Assembly
100 °C
100 °C
Ts typical 120 °C
120 °C
Ts max
130 °C
130 °C
ts
70 seconds
70 seconds
Ramp-up Rate
ΔT
150 °C max.
150 °C max.
Peak Temperature
Tp
250 °C - 260 °C
235 °C - 260 °C
Time of actual peak temperature
tp
max. 10 seconds
max. 5 seconds each wave
max. 10 seconds
max. 5 seconds each wave
Preheat Time ts from Ts min to Ts max
Temperature
Pb-Free Assembly
Ts min
Ts max
Ts typical
Ramp-down Rate, Min
~ 2 K/ second
~ 2 K/ second
Ramp-down Rate, Typical
~ 3.5 K/ second
~ 3.5 K/ second
Ts min
Ramp-down Rate, Max
~ 5 K/ second
~ 5 K/ second
Time 25 °C to 25 °C
4 minutes
4 minutes
refer to EN61760-1:2006
Preheat area
Cool down area
Time
typical temperature procedure
min temperature procedure
max temperature procedure
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
6/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Cautions and Warnings:
5. Flammability:
The following conditions apply to all goods within the product series of WCAP-FTX2 of
Würth Elektronik eiSos GmbH & Co. KG:
Avoid any external energy or open fire (passive flammability).
1. General:
Do not exceed the vibration limits given by IEC60068-2-6.
The capacitor is engineered, designed and manufactured to be used within the datasheet specified values. Do not use the capacitor neither
short term nor long term outside the specified values, which are given in the data sheet.
7. Cleaning:
6. Vibration resistance:
2. Product specific:
Do not use any other cleaning solvents for box-typed capacitors except: ethanol, isopropanol, n-propanol - water mixtures. After cleaning a
drying process with temperatures not exceeding 65°C and not longer than 4 hours is mandatory to prevent any kind of electrical damage.
Follow all instructions mentioned in the data sheet, especially:
8. Full covered or embedded capacitors in final applications:
• The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise this will void the
warranty.
• Wave soldering is only allowed after evaluation and approval.
• Do not exceed the lower and/ or upper specified temperature!
• Do not use the capacitor with other than specified voltage!
• Prevent any kind of mechanical stress to the capacitor terminals!
• Do not use the soldered capacitor on a PCB for any movement or transportation to avoid any tensile force to the capacitor!
• Do not apply any kind of flexural or compressive force onto soldered or unsoldered component!
• Prevent the capacitor surface from any damage or scratches with sharp edges (e.g. chassis, screwdrivers, pincers).
• The capacitor must be placed on a PCB while using the recommended drill hole pattern without changing of the specific lead pitch!
• Avoid any other than specified temperature and / or time conditions during soldering!
• Avoid any overload or conditions that are not specified in the capacitors datasheet!
• Avoid any water or heavy dust on capacitors surface which may cause electrical leakage, damage, overheating or corrosion!
• FTX2 is not recommended to be used in ther series to mains application.
If final assemblies will be placed completely in any plastic resin, physical, chemical and thermal influences must be considered. If any
specific evaluation or test is necessary please contact the related Würth Elektronik Capacitor Business Division.
3. Storage conditions:
These film capacitors must be stored in stable climatic conditions, which are listed within the general information on front of data sheet.
4. Storage duration:
All products shall be used before the end of the period of 12 months based on the product date code, if not a 100% solderability can´t be
ensured.
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
7/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Important Notes
6. Product Life Cycle
The following conditions apply to all goods within the product range of Würth Elektronik
eiSos GmbH & Co. KG:
Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a
standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage
about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be
available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product
availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not
apply in the case of individual agreements deviating from the foregoing for customer-specific products.
1. General Customer Responsibility
Some goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain
application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the
areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The
responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this
fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product
characteristics described in the product specification is valid and suitable for the respective customer application or not.
2. Customer Responsibility related to Specific, in particular Safety-Relevant Applications
It has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime
cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.
In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable
design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic
component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be
downloaded at www.we-online.com.
7. Property Rights
All the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as
well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth
Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or
implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination,
application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.
8. General Terms and Conditions
Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth
Elektronik eiSos Group”, last version available at www.we-online.com.
3. Best Care and Attention
Any product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.
4. Customer Support for Product Specifications
Some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve
specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales
person in charge should be contacted who will be happy to support in this matter.
5. Product R&D
Due to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the
Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries
regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the
customer as per Section 1 and 2 remains unaffected.
Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. +49 (0) 79 42 945 - 0
CREATED
CHECKED
GENERAL TOLERANCE
KaS
PSL
DIN ISO 2768-1m
PROJECTION
METHOD
DESCRIPTION
TECHNICAL REFERENCE
WCAP-FTX2 Film Capacitors
MX2P015393K275ACPP45004
ORDER CODE
www.we-online.com
eiSos@we-online.com
890324025007CS
SIZE
REVISION
STATUS
DATE (YYYY-MM-DD)
BUSINESS UNIT
PAGE
Pitch 15
002.000
Valid
2018-03-01
eiCap
8/8
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Wurth Elektronik:
890324025007CS
