890493422002CS

Dimensions: [mm] Recommended Hole Pattern: [mm] Electrical Properties: Properties Test conditions Capacitance 1 V/ 1 kHz ± 0.2 kHz Of OF Rated Voltage P Tol. nF ±10% UR 1000 V (DC) 1 min @ 500 V (DC) RISO 9000 MΩ min. Dissipation Factor @ 1 kHz DF 1 % max. Dissipation Factor @ 10 kHz DF 1.4 % max. Dissipation Factor @ 100 kHz DF 2.2 % max. dV/dt 160 V/µs max. Dielectric Strength Pin to Pin 1 min 1500 V (DC) Dielectric Strength Pin to Case 5 sec. 2000 V (DC) H L Unit 10 Insulation Resistance Rate of Voltage Rise p Value C G Schematic: General Information: W General Purpose; wound type; boxed; MKT-Metallized polyester Storage Conditions 5-35 °C, < 75% RH Operating Temperature -40 °C up to +85 °C Maxium Selfheating (Rated) 10 °C Test conditions of Electrical Properties: +20°C, 35% RH if not specified differently FIT according to separate documentation Component conform to REACh and RoHS requirements and standards Properties Value Unit Tol. Pitch P 7.5 mm ±0.5 Length L 10.5 mm ±1.5 Height H 12 mm ±1 Width W 6 mm ±1 Pin Diameter ØF 0.6 Pin length G 4 mm ±0.5 Pitch p 7.5 mm ±0.5 Pin Hole Diameter Øf 0.9 mm ±0.05 mm ±0.05 Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 CREATED CHECKED GENERAL TOLERANCE KaS PSL DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-FTBE Film Capacitors MPSP075103KA00DCPP45004 ORDER CODE www.we-online.com eiSos@we-online.com 890493422002CS SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE Pitch 7.5 002.000 Valid 2017-12-20 eiCap 1/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Product Marking: 1st Capacitance Change vs. Temperature: Line right 5.0% Matchcode: FTBE 2nd Line right Rated Voltage: 1000 V 2nd Line left Capacitance & Tolerance Code: 103 K (Basis pF) Top Cover Marking P < 15 Date Code: YWW Top Cover Marking P ≥ 15 Date Code & Capacitance & Tolerance Code 3.0% Properties Test Conditions Termination Robustness IEC 600668 - 2 - 21 Pull Test File Bend Test Lead Diameter [mm] Force [N] condition 0.5 to ≤ 0.8 10 min. 10 sec. 0.9 to ≤ 1.25 20 min. 10 sec. 0.5 to ≤ 0.8 5 min. 2 cycles 0.9 to ≤ 1.25 10 min. 2 cycles Environmental Tests: Properties Standard Vibration IEC 60068 - 2 - 6 all 3 directions, 2 hours each @ 15 - 55 - 15 Hz, amplitude 0.75 mm or 10 g Damp Heat IEC 60068 - 2 - 78 40°C, 95% RH, 56 days Temperature Cycles IEC 60068 - 2 - 14 5 cycles, upper and lower temperature 30 min. each, 30 sec. transfer time Capacitance Change [%] Mechanical Properties 1.0% -1.0% -3.0% -5.0% -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 105 Temperature [°C] Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 CREATED CHECKED GENERAL TOLERANCE KaS PSL DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-FTBE Film Capacitors MPSP075103KA00DCPP45004 ORDER CODE www.we-online.com eiSos@we-online.com 890493422002CS SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE Pitch 7.5 002.000 Valid 2017-12-20 eiCap 2/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Rated Voltage vs. Temperature: 1.2% 120.0% 1.0% 100.0% 0.8% 80.0% Rated Voltage / Max Voltage [%] Dissipation Factor [%] Dissipation Factor vs. Temperature: 0.6% 0.4% 0.2% 60.0% 40.0% 20.0% 0.0% 0.0% -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 105 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 85 90 95 100 105 Temperature [°C] Temperature [°C] Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 CREATED CHECKED GENERAL TOLERANCE KaS PSL DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-FTBE Film Capacitors MPSP075103KA00DCPP45004 ORDER CODE www.we-online.com eiSos@we-online.com 890493422002CS SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE Pitch 7.5 002.000 Valid 2017-12-20 eiCap 3/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Packaging Specification - Carton: [mm] L H H C IC Paperboard IC L W W C C IC LIC (mm) WIC (mm) HIC (mm) typ. 275,00 typ. 160,00 typ. 95,00 No. of Paperboard pcs. 5 No. of Layer pcs. 4 Packaging Unit pcs. 2580 Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 Material LC (mm) WC (mm) HC (mm) typ. 500,00 typ. 290,00 typ. 240,00 No. of inner Carton pcs. 6 Packaging Unit pcs. 15480 Material Paper Paper CREATED CHECKED GENERAL TOLERANCE KaS PSL DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-FTBE Film Capacitors MPSP075103KA00DCPP45004 ORDER CODE www.we-online.com eiSos@we-online.com 890493422002CS SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE Pitch 7.5 002.000 Valid 2017-12-20 eiCap 4/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Classification Wave Soldering Profile: Classification Wave Soldering Profile: Profile Feature tp Tp Preheat Temperature Min Preheat Temperature Typical First Wave Second Wave Preheat Temperature Max Sn-Pb Assembly 100 °C 100 °C Ts typical 120 °C 120 °C Ts max 130 °C 130 °C ts 70 seconds 70 seconds Ramp-up Rate ΔT 150 °C max. 150 °C max. Peak temperature Tp 250 °C - 260 °C 235 °C - 260 °C Time of actual peak temperature tp max. 10 seconds max. 5 seconds each wave max. 10 seconds max. 5 seconds each wave Preheat Time ts from Ts min to Ts max Temperature Pb-Free Assembly Ts min Ts max Ts typical Ramp-down Rate, Min ~ 2 K/ second ~ 2 K/ second Ramp-down Rate, Typical ~ 3.5 K/ second ~ 3.5 K/ second Ts min Ramp-down Rate, Max ~ 5 K/ second ~ 5 K/ second Time 25°C to 25°C 4 minutes 4 minutes refer to EN61760-1:2006 Preheat area Cool down area Time typical temperature procedure min temperature procedure max temperature procedure Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 CREATED CHECKED GENERAL TOLERANCE KaS PSL DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-FTBE Film Capacitors MPSP075103KA00DCPP45004 ORDER CODE www.we-online.com eiSos@we-online.com 890493422002CS SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE Pitch 7.5 002.000 Valid 2017-12-20 eiCap 5/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Cautions and Warnings: Avoid any external energy or open fire (passive flammability). The following conditions apply to all goods within the product series of WCAP-FTBE of Würth Elektronik eiSos GmbH & Co. KG: 6. Vibration resistance: 1. General: 7. Cleaning: The capacitor is engineered, designed and manufactured to be used within the datasheet specified values. Do not use the capacitor neither short term nor long term outside the specified values, which are given in the data sheet. Do not use any other cleaning solvents for box-typed capacitors except: ethanol, isopropanol, n-propanol - water mixtures. After cleaning a drying process with temperatures not exceeding 65°C and not longer than 4 hours is mandatory to prevent any kind of electrical damage. 2. Product specific: 8. Full covered or embedded capacitors in final applications: Follow all instructions mentioned in the data sheet, especially: If final assemblies will be placed completely in any plastic resin, physical, chemical and thermal influences must be considered. If any specific evaluation or test is necessary please contact the related Würth Elektronik Capacitor Business Division. Do not exceed the vibration limits given by IEC60068-2-6. • The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise this will void the warranty. • Wave soldering is only allowed after evaluation and approval. • Do not exceed the lower and/ or upper specified temperature! • Do not use the capacitor with other than specified voltage! • Prevent any kind of mechanical stress to the capacitor terminals! • Do not use the soldered capacitor on a PCB for any movement or transportation to avoid any tensile force to the capacitor! • Do not apply any kind of flexural or compressive force onto soldered or unsoldered component! • Prevent the capacitor surface from any damage or scratches with sharp edges (e.g. chassis, screwdrivers, pincers). • The capacitor must be placed on a PCB while using the recommended drill hole pattern without changing of the specific lead pitch! • Avoid any other than specified temperature and / or time conditions during soldering! • Avoid any overload or conditions that are not specified in the capacitors datasheet! • Avoid any water or heavy dust on capacitors surface which may cause electrical leakage, damage, overheating or corrosion! 3. Storage conditions: These film capacitors must be stored in stable climatic conditions, which are listed within the general information on front of data sheet. 4. Storage duration: All products shall be used before the end of the period of 12 months based on the product date code, if not a 100% solderability can´t be ensured. 5. Flammability: Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 CREATED CHECKED GENERAL TOLERANCE KaS PSL DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-FTBE Film Capacitors MPSP075103KA00DCPP45004 ORDER CODE www.we-online.com eiSos@we-online.com 890493422002CS SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE Pitch 7.5 002.000 Valid 2017-12-20 eiCap 6/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. Important Notes 6. Product Life Cycle The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG: Due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 1. General Customer Responsibility Some goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not. 2. Customer Responsibility related to Specific, in particular Safety-Relevant Applications It has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications. In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at www.we-online.com. 7. Property Rights All the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used. 8. General Terms and Conditions Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at www.we-online.com. 3. Best Care and Attention Any product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty. 4. Customer Support for Product Specifications Some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter. 5. Product R&D Due to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected. Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 1 74638 Waldenburg Germany Tel. +49 (0) 79 42 945 - 0 CREATED CHECKED GENERAL TOLERANCE KaS PSL DIN ISO 2768-1m PROJECTION METHOD DESCRIPTION TECHNICAL REFERENCE WCAP-FTBE Film Capacitors MPSP075103KA00DCPP45004 ORDER CODE www.we-online.com eiSos@we-online.com 890493422002CS SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE Pitch 7.5 002.000 Valid 2017-12-20 eiCap 7/7 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.