X88257PM

X88257 8051 Microcontroller Family Compatible 256K X88257 E2 Micro-Peripheral DESCRIPTION 32,768 x 8 Bit FEATURES • Multiplexed Address/Data Bus —Direct Interface to Popular 8051 Family • High Performance CMOS —Fast Access Time, 120ns —Low Power —60mA Active Maximum —500µA Standby Maximum • Software Data Protection • Toggle Bit Polling —Early End of Write Detection • Page Mode Write —Allows up to 128 Bytes to be Written in One Write Cycle • High Reliability —Endurance: 10,000 Write Cycle —Data Retention: 100 Years • 28-Lead PDIP Package • 28-Lead SOIC Package • 32-Lead PLCC Package The X88257 is an 32K x 8 E2PROM fabricated with advanced CMOS Textured Poly Floating Gate Technology. The X88257 features a multiplexed address and data bus allowing direct interface to a variety of popular single-chip microcontrollers operating in expanded multiplexed mode without the need for additional interface circuitry. FUNCTIONAL DIAGRAM CE, CE WR RD PSEN A8–A14 CONTROL LOGIC X D E C O D E SOFTWARE DATA PROTECT ALE L A T C H E S 32K x 8 E2PROM Y DECODE I/O & ADDRESS LATCHES AND BUFFERS A/D0–A/D7 6509 ILL F02.1 © Xicor, Inc. 1994-1997 Patents Pending 6509-1.9 4/9/96 T2/C5/D8 NS 1 Characteristics subject to change without notice X88257 PIN DESCRIPTIONS Address/Data (A/D0–A/D7) Multiplexed low-order addresses and data. The addresses flow into the device while ALE is HIGH. After ALE transitions from a HIGH to LOW the addresses are latched. Once the addresses are latched these pins input data or output data depending on RD, WR, PSEN, and CE. Addresses (A8–A14) High order addresses flow into the device when ALE = VIH and are latched when ALE goes LOW. Chip Enable (CE) The Chip Enable input must be LOW to enable all read/ write operations. When CE is HIGH, ALE is LOW, and CE is LOW, the X88257 is placed in the low power standby mode. If CE is used to select the device, the CE must be tied LOW. Chip Enable (CE) Chip enable is active HIGH. When CE is used to select the device, the CE must be tied HIGH. Program Store Enable (PSEN) When the X88257 is to be used in a 8051-based system, PSEN is tied directly to the microcontroller’s PSEN output. Read (RD) When the X88257 is to be used in a 8051-based system, RD is tied directly to the microcontroller’s RD output. Write (WR) When the X88257 is to be used in a 8051-based system, WR is tied directly to the microcontroller’s WR output. Address Latch Enable (ALE) Addresses flow through the latches to address decoders when ALE is HIGH and are latched when ALE transitions from a HIGH to LOW. PIN NAMES Symbol ALE A/D0–A/D7 A8–A14 RD WR PSEN CE, CE VSS VCC NC 2 PSEN CE NC NC NC NC NC NC A/D0 5 6 7 8 9 10 11 12 X88257 A14 A12 ALE PSEN CE NC NC NC NC NC A/D0 A/D1 A/D2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PIN CONFIGURATION PDIP SOIC 28 27 26 25 24 23 X88257 22 21 20 19 18 17 16 15 VCC WR A13 A8 A9 A11 RD A10 CE A/D7 A/D6 A/D5 A/D4 A/D3 6509 FHD F01.3 PLCC ALE VCC A12 A14 NC WR A13 4 3 2 1 32 31 30 29 28 27 26 25 24 23 22 A8 A9 A11 NC RD A10 CE A/D7 A/D6 13 21 14 15 16 17 18 19 20 A/D1 A/D2 VSS A/D3 A/D4 A/D5 NC 6509 FHD F01A.5 Description Address Latch Enable Address Inputs/Data I/O Address Inputs Read Input Write Input Program Store Enable Input Chip Enable Ground Supply Voltage No Connect 6509 PGM T01.1 X88257 TYPICAL APPLICATION U? 31 19 EA/VP X1 P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 P2.7 RD WR PSEN ALE/P TXD RXD 39 38 37 36 35 34 33 32 21 22 23 24 25 26 27 28 17 16 29 30 11 10 11 12 12 15 16 17 18 19 A/D0 A/D1 A/D2 A/D3 A/D4 A/D5 A/D6 A/D7 18 9 X2 RESET 12 13 14 15 1 2 3 4 5 6 7 8 INT0 INT1 T0 T1 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 8051 25 A8 24 A9 21 A10 23 A11 2 A12 26 A13 1 A14 20 CE CE 22 RD 27 WR 4 PSEN 3 ALE X88257 6509 ILL F03.3 5 PRINCIPLES OF OPERATION The X88257 is a highly integrated peripheral device for a wide variety of single-chip microcontrollers. The X88257 provides 32K-bytes of 5V E2PROM which can be used either for program storage, data storage or a combination of both, in systems based upon Harvard (80XX) architectures. The X88257 incorporates the interface circuitry normally needed to decode the control signals and demultiplex the address/data bus to provide a “seamless” interface. The interface inputs on the X88257 are configured such that it is possible to directly connect them to the proper interface signals of the appropriate single-chip microcontroller. In the Harvard type system, the reading of data from the chip is controlled either by the PSEN or the RD signal, which essentially maps the X88257 into both the Program and the Data Memory address map. The X88257 also features the industry standard 5V E2PROM characteristics such as byte or page mode write and Toggle Bit Polling. 3 DEVICE OPERATION Modes—Mixed Program/Data Memory By properly assigning the address spaces, a single X88257 can be used as both the program and data memory. This would be accomplished by connecting all the 8051 control outputs to the corresponding inputs of the X88257. Program Memory Mode This mode of operation is read-only. The PSEN and ALE inputs of the X88257 are tied directly to the PSEN and ALE outputs of the microcontroller. The RD and WR inputs are tied HIGH. When ALE is HIGH, the A/D0–A/D7 and A8–A14 addresses flow into the device. The addresses, both lowand high-order, are latched when ALE transitions LOW (VIL). PSEN will then go LOW and after tPLDV; Valid data is presented on the A/D0–A/D7 pins. CE must be LOW during the entire operation. X88257 DATA MEMORY MODE This mode of operation allows both read and write functions. The PSEN input is tied to VIH or to VCC through a pull-up resistor. The ALE, RD, and WR inputs are tied directly to the microcontroller ALE, RD, and WR outputs. Read This operation is quite similar to the program memory read. A HIGH to LOW transition on ALE latches the addresses and the data will be output on the AD pins after RD goes LOW (tRLDV). Write A write is performed by latching the addresses on the falling edge of ALE. Then WR is strobed LOW followed by valid data being presented at the A/D0–A/D7 pins. The data will be latched into the X88257 on the rising edge of WR. To write to the X88257, a three-byte command sequence must precede the byte(s) being written. (See Software Data Protection.) MODE SELECTION CE VCC HIGH LOW LOW LOW PSEN X X LOW HIGH HIGH RD X X HIGH LOW HIGH WR X X HIGH HIGH Mode Standby Standby Read Read Write I/O High Z High Z DOUT DOUT DIN Power Standby (CMOS) Standby (TTL) Active Active Active 6509 PGM T02 PAGE WRITE OPERATION Regardless of the microcontroller employed, the X88257 supports page mode write operations. This allows the microcontroller to write from 1 to 128 bytes of data to the X88257. Each individual write within a page write operation must conform to the byte write timing requirements. The falling edge of WR starts a timer delaying the internal programming cycle 100µs. Therefore, each successive write operation must begin within 100µs of the last byte written. The following waveforms illustrate the sequence and timing requirements. Page Write Timing Sequence for WR Controlled Operation OPERATION BYTE 0 BYTE 1 BYTE 2 LAST BYTE READ (1)(2) AFTER tWC READY FOR NEXT WRITE OPERATION CE ALE A/D0–A/D7 AIN DIN AIN DIN AIN DIN AIN DIN AIN DOUT AIN AIN A8–A14 An An An An An ADDR Next Address WR PSEN(RD) tBLC tWC 6509 ILL F08.1 Notes: (1) For each successive write within a page write cycle A7–A14 must be the same. 4 X88257 TOGGLE BIT POLLING Because the typical write timing is less than the specified 5ms, Toggle Bit Polling has been provided to determine the early end of write. During the internal programming cycle I/O6 will toggle from “1” to “0” and “0” to “1” on Toggle Bit Polling RD/WR Control OPERATION LAST BYTE WRITTEN I/O6=X I/O6=X I/O6=X I/O6=X X88C64 READY FOR NEXT OPERATION subsequent attempts to read the device. When the internal cycle is complete the toggling will cease and the device will be accessible for additional read or write operations. CE ALE A/D0–A/D7 AIN DIN AIN DOUT AIN DOUT AIN DOUT AIN DOUT AIN A8–A14 An An An An An ADDR WR RD 6509 ILL F09.1 SOFTWARE DATA PROTECTION Software Data Protection (SDP) is employed to protect the entire array against inadvertent writes. To write to the X88257, a three-byte command sequence must precede the byte(s) being written. All write operations, both the command sequence and any data write operations must conform to the page write timing requirements. Writing with SDP WRITE AA TO 5555 WRITE 55 TO 2AAA WRITE A0 TO 5555 PERFORM BYTE OR PAGE WRITE OPERATIONS WAIT tWC EXIT ROUTINE 6509 ILL F10.1 5 X88257 ABSOLUTE MAXIMUM RATINGS* Temperature under Bias .................. –65°C to +135°C Storage Temperature ....................... –65°C to +150°C Voltage on any Pin with Respect to VSS .................................. –1V to +7V D.C. Output Current ............................................. 5mA Lead Temperature (Soldering, 10 seconds) .............................. 300°C *COMMENT Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and the functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Temperature Commercial Industrial Military Min. 0°C –40°C –55°C Max. +70°C +85°C +125°C 6509 PGM T03.1 Supply Voltage X88257 Limits 5V ± 10% 6509 PGM T04.1 D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified.) Limits Symbol ICC ISB1(CMOS) Parameter VCC Current (Active) VCC Current (Standby) Min. Max. 60 500 Units mA µA Test Conditions CE = RD = VIL, All I/O’s = Open,Other Inputs = VCC CE = VCC – 0.3V, All I/O’s = Open,Other Inputs = VCC – 0.3V, ALE = VIL CE = VIH, All I/O’s = Open, Other Inputs = VIH, ALE = VIL VIN = VSS to VCC VOUT = VSS to VCC, RD = VIH = PSEN ISB2(TTL) ILI ILO VlL(3) VIH(3) VOL VOH VCC Current (Standby) Input Leakage Current Output Leakage Current Input LOW Voltage Input HIGH Voltage Output LOW Voltage Output HIGH Voltage –1 2 2.4 6 10 10 0.8 VCC + 0.5 0.4 mA µA µA V V V V IOL = 2.1mA IOH = –400µA 6509 PGM T05.1 CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V Symbol CI/O(4) CIN(4) POWER-UP TIMING Symbol tPUR(4) tPUW(4) Parameter Power-Up to Read Power-Up to Write Max. 1 5 Units ms ms 6509 PGM T07 Test Input/Output Capacitance Input Capacitance Max. 10 6 Units pF pF Conditions VI/O = 0V VIN = 0V 6509 PGM T06 Notes: (3) VIL min. and VIH max. are for reference only and are not tested. (4) This parameter is periodically sampled and not 100% tested. 6 X88257 A.C. CONDITIONS OF TEST Input Pulse Levels Input Rise and Fall Times Input and Output Timing Levels 0V to 3V 10ns 1.5V 6509 PGM T08.1 EQUIVALENT A.C. TEST CIRCUIT 5V 1.92KΩ OUTPUT 1.37KΩ 100pF 6509 ILL F04.3 A.C. CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.) PSEN Controlled Read Cycle Symbol tLHLL tAVLL tLLAX tPLDV tPHDX tELLL PWPL tPS tPH tPHDZ (5) tPLDX (5) Parameter ALE Pulse Width Address Setup Time Address Hold Time PSEN Read Access Time Data Hold Time Chip Enable Setup Time PSEN Pulse Width PSEN Setup Time PSEN Hold Time PSEN Disable to Output in High Z PSEN to Output in Low Z Min. 80 20 30 120 0 7 150 30 20 50 10 Max. Units ns ns ns ns ns ns ns ns ns ns ns 6509 PGM T09 PSEN Controlled Read Timing Diagram tPH CE tLHLL ALE tAVLL A/D0–A/D7 AIN tPLDX tPLDV A8–A14 tPS PSEN 6509 ILL F05.1 tELLL tPH tLLAX DOUT tPHDX tPHDZ ADDRESS PWPL Note: (5) This parameter is periodically sampled and not 100% tested. 7 X88257 RD Controlled Read Cycle Symbol tLHLL tAVLL tLLAX tRLDV tRHDX tELLL PWRL tRDS tRDH tRHDZ (6) tRLDX (6) Parameter ALE Pulse Width Address Setup Time Address Hold Time RD Read Access Time Data Hold Time Chip Enable Setup Time RD Pulse Width RD Setup Time RD Hold Time RD Disable to Output in High Z RD to Output in Low Z Min. 80 20 30 120 0 7 150 30 20 50 0 Max. Units ns ns ns ns ns ns ns ns ns ns ns 6509 PGM T10 RD Controlled Read Timing Diagram tRDH CE tLHLL ALE tAVLL A/D0–A/D7 AIN tRLDX tRLDV A8–A14 tRDS RD 6509 ILL F06.1 tELLL tRDH tLLAX DOUT tRHDX tRHDZ ADDRESS PWRL Note: (6) This parameter is periodically sampled and not 100% tested. SYMBOL TABLE WAVEFORM INPUTS Must be steady May change from LOW to HIGH May change from HIGH to LOW Don’t Care: Changes Allowed N/A OUTPUTS Will be steady Will change from LOW to HIGH Will change from HIGH to LOW Changing: State Not Known Center Line is High Impedance 8 X88257 WR Controlled Write Cycle Symbol tLHLL tAVLL tLLAX tDVWH tWHDX tELLL tWLWH tWRS tWRH tBLC tWC (7) Parameter ALE Pulse Width Address Setup Time Address Hold Time Data Setup Time Data Hold Time Chip Enable Setup Time WR Pulse Width WR Setup Time WR Hold Time Byte Load Time (Page Write) Write Cycle Time Min. 80 20 30 50 30 7 120 30 20 0.5 Max. Units ns ns ns ns ns ns ns ns ns µs ms 6509 PGM T11 100 5 WR Controlled Write Timing Diagram tWRH CE tLHLL ALE tAVLL A/D0–A/D7 AIN tLLAX DIN tDVWH A8–A14 tWRS WR 6509 ILL F07.1 tELLL tWRH tWHDX ADDRESS tWLWH Note: (7) tWC is the minimum cycle time to be allowed from the system perspective unless polling techniques are used. It is the maximum time the device requires to automatically complete the internal write operation. 9 X88257 NOTES 10 X88257 NOTES 11 X88257 PACKAGING INFORMATION 28-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P 1.470 (37.34) 1.400 (35.56) 0.557 (14.15) 0.510 (12.95) PIN 1 INDEX PIN 1 1.300 (33.02) REF. 0.085 (2.16) 0.040 (1.02) SEATING PLANE 0.160 (4.06) 0.120 (3.05) 0.160 (4.06) 0.125 (3.17) 0.030 (0.76) 0.015 (0.38) 0.110 (2.79) 0.090 (2.29) 0.065 (1.65) 0.040 (1.02) 0.022 (0.56) 0.014 (0.36) 0.625 (15.88) 0.590 (14.99) TYP. 0.010 (0.25) 0° 15° NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH 3926 FHD F04 12 X88257 PACKAGING INFORMATION 28-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S 0.299 (7.59) 0.290 (7.37) 0.419 (10.64) 0.394 (10.01) 0.020 (0.508) 0.014 (0.356) 0.713 (18.11) 0.697 (17.70) 0.105 (2.67) 0.092 (2.34) BASE PLANE SEATING PLANE 0.050 (1.270) BSC 0.012 (0.30) 0.003 (0.08) 0.050" TYPICAL 0.0200 (0.5080) X 45° 0.0100 (0.2540) 0.013 (0.32) 0.008 (0.20) 0.050" TYPICAL 0.42" MAX 0° – 8° 0.0350 (0.8890) 0.0160 (0.4064) FOOTPRINT 0.030" TYPICAL 28 PLACES NOTES: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. FORMED LEAD SHALL BE PLANAR WITH RESPECT TO ONE ANOTHER WITHIN 0.004 INCHES 3926 FHD F17 13 X88257 PACKAGING INFORMATION 32-LEAD PLASTIC LEADED CHIP CARRIER PACKAGE TYPE J 0.420 (10.67) 0.050" TYPICAL 0.030" TYPICAL 32 PLACES 0.510" TYPICAL 0.050" TYPICAL 0.400" 0.050 (1.27) TYP. FOOTPRINT 0.300" REF 0.410" 0.045 (1.14) x 45° 0.021 (0.53) 0.013 (0.33) TYP. 0.017 (0.43) 0.495 (12.57) 0.485 (12.32) TYP. 0.490 (12.45) 0.453 (11.51) 0.447 (11.35) TYP. 0.450 (11.43) 0.300 (7.62) REF. PIN 1 SEATING PLANE ±0.004 LEAD CO – PLANARITY — 0.015 (0.38) 0.095 (2.41) 0.060 (1.52) 0.140 (3.56) 0.100 (2.45) TYP. 0.136 (3.45) 0.048 (1.22) 0.042 (1.07) 0.595 (15.11) 0.585 (14.86) TYP. 0.590 (14.99) 0.553 (14.05) 0.547 (13.89) TYP. 0.550 (13.97) 0.400 (10.16)REF. 3° TYP. NOTES: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. DIMENSIONS WITH NO TOLERANCE FOR REFERENCE ONLY 3926 FHD F13 14 X88257 ORDERING INFORMATION X88257 Device X X Temperature Range Blank = Commercial = 0°C to +70°C I = Industrial = –40°C to +85°C M = Military = –55°C to +125°C Package P = 28-Lead Plastic DIP S = 28-Lead SOIC J = 32-Lead PLCC LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Xicor, Inc. makes no warranty of merchantability or fitness tor any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices at any time and without notice. Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, licenses are implied. US. PATENTS Xicor products are covered by one or more of the following U.S. Patents: 4,263,664; 4,274,012; 4,300,212; 4,314,265; 4,326,134; 4,393,481; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694. Foreign patents and additional patents pending. LIFE RELATED POLICY In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detection and correction, redundancy and back-up features to prevent such an occurrence. Xicor’s products are not authorized for use as critical components in life support devices or systems. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its satety or effectiveness. 15