Kintex UltraScale+ FPGAs Data Sheet:
DC and AC Switching Characteristics
DS922 (v1.17) February 16, 2021
Product Specification
Summary
The Xilinx® Kintex® UltraScale+™ FPGAs are available in -3, -2, -1 speed grades, with -3E devices having the
highest performance. The -2LE and -1LI devices can operate at a VCCINT voltage at 0.85V or 0.72V and provide
lower maximum static power. When operated at VCCINT = 0.85V, using -2LE and -1LI devices, the speed
specification for the L devices is the same as the -2I or -1I speed grades. When operated at VCCINT = 0.72V, the
-2LE and -1LI performance and static and dynamic power is reduced.
DC and AC characteristics are specified in extended (E), industrial (I), and military (M) temperature ranges.
Except the operating temperature range or unless otherwise noted, all the DC and AC electrical parameters are
the same for a particular speed grade (that is, the timing characteristics of a -1 speed grade extended device are
the same as for a -1 speed grade industrial device). However, only selected speed grades and/or devices are
available in each temperature range.
The XQ references in this data sheet are specific to the devices available in XQ Ruggedized packages. See the
Defense-Grade UltraScale Architecture Data Sheet: Overview (DS895) for further information on XQ Defensegrade part numbers, packages, and ordering information.
All supply voltage and junction temperature specifications are representative of worst-case conditions. The
parameters included are common to popular designs and typical applications.
This data sheet, part of an overall set of documentation on the Kintex UltraScale+ FPGAs, is available on the
Xilinx website at www.xilinx.com/documentation.
DC Characteristics
Absolute Maximum Ratings
Table 1: Absolute Maximum Ratings
Description1
Symbol
Min
Max
Units
FPGA Logic
VCCINT
Internal supply voltage
–0.500
1.000
V
VCCINT_IO2
Internal supply voltage for the I/O banks
–0.500
1.000
V
VCCAUX
Auxiliary supply voltage
–0.500
2.000
V
© Copyright 2015–2021 Xilinx, Inc. Xilinx, the Xilinx logo, Alveo, Artix, Kintex, Spartan, Versal, Virtex, Vitis, Vivado, Zynq, and other designated
brands included herein are trademarks of Xilinx in the United States and other countries. PCI, PCIe, and PCI Express are trademarks of PCI-SIG
and used under license. The DisplayPort Icon is a trademark of the Video Electronics Standards Association, registered in the U.S. and other
countries. All other trademarks are the property of their respective owners.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
1
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 1: Absolute Maximum Ratings (cont'd)
Description1
Symbol
Min
Max
Units
VCCBRAM
Supply voltage for the block RAM memories
–0.500
1.000
V
VCCO
Output drivers supply voltage for HD I/O banks
–0.500
3.400
V
Output drivers supply voltage for HP I/O banks
–0.500
2.000
V
3
VCCAUX_IO
Auxiliary supply voltage for the I/O banks
–0.500
2.000
V
VREF
Input reference voltage
–0.500
2.000
V
VIN4, 5, 6
I/O input voltage for HD I/O banks
–0.550
VCCO + 0.550
V
I/O input voltage for HP I/O banks
–0.550
VCCO + 0.550
V
Key memory battery backup supply
–0.500
2.000
V
IDC
Available output current at the pad
–20
20
mA
IRMS
Available RMS output current at the pad
–20
20
mA
VBATT
GTH or GTY Transceiver7
VMGTAVCC
Analog supply voltage for transceiver circuits
–0.500
1.000
V
VMGTAVTT
Analog supply voltage for transceiver termination circuits
–0.500
1.300
V
VMGTVCCAUX
Auxiliary analog Quad PLL (QPLL) voltage supply for transceivers
–0.500
1.900
V
VMGTREFCLK
Transceiver reference clock absolute input voltage
–0.500
1.300
V
VMGTAVTTRCAL
Analog supply voltage for the resistor calibration circuit of the
transceiver column
–0.500
1.300
V
VIN
Receiver (RXP/RXN) and transmitter (TXP/TXN) absolute input
voltage
–0.500
1.200
V
IDCIN-FLOAT
DC input current for receiver input pins DC coupled RX
termination = floating8
–
10
mA
IDCIN-MGTAVTT
DC input current for receiver input pins DC coupled RX
termination = VMGTAVTT
–
10
mA
IDCIN-GND
DC input current for receiver input pins DC coupled RX
termination = GND9
–
0
mA
IDCIN-PROG
DC input current for receiver input pins DC coupled RX
termination = programmable10
–
0
mA
IDCOUT-FLOAT
DC output current for transmitter pins DC coupled RX
termination = floating
–
6
mA
IDCOUT-MGTAVTT
DC output current for transmitter pins DC coupled RX
termination = VMGTAVTT
–
6
mA
System Monitor
VCCADC
System Monitor supply relative to GNDADC
–0.500
2.000
V
VREFP
System Monitor reference input relative to GNDADC
–0.500
2.000
V
–65
150
°C
Temperature11
TSTG
Storage temperature (ambient)
TSOL
Maximum dry rework soldering temperature
–
260
°C
Maximum reflow soldering temperature for SFVB784, FFVA676, and
FFVB676 packages
–
250
°C
Maximum reflow soldering temperature for FFVD900, FFVE900,
FFVA1156, FFVE1517, FFVA1760, FFVE1760, FFVJ1760, and FFVB2104
packages
–
245
°C
Maximum reflow soldering temperature for the FFRB676, SFRB784,
FFRA1156, and FFRE1517 packages
–
225
°C
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
2
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 1: Absolute Maximum Ratings (cont'd)
Description1
Symbol
Tj
Min
Max
Units
–
125
°C
Maximum junction temperature
Notes:
1.
Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not
implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability.
2.
VCCINT_IO must be connected to VCCBRAM.
3.
VCCAUX_IO must be connected to VCCAUX.
4.
The lower absolute voltage specification always applies.
5.
For I/O operation, see the UltraScale Architecture SelectIO Resources User Guide (UG571).
6.
When operating outside of the recommended operating conditions, refer to Table 4 and Table 5 for maximum overshoot and
undershoot specifications.
7.
For more information on supported GTH or GTY transceiver terminations see the UltraScale Architecture GTH Transceivers User Guide
(UG576) or UltraScale Architecture GTY Transceivers User Guide (UG578).
8.
AC coupled operation is not supported for RX termination = floating.
9.
For GTY transceivers, DC coupled operation is not supported for RX termination = GND.
10. DC coupled operation is not supported for RX termination = programmable.
11. For soldering guidelines and thermal considerations, see the UltraScale and UltraScale+ FPGAs Packaging and Pinouts Product Specification
(UG575).
Recommended Operating Conditions
Table 2: Recommended Operating Conditions
Description1, 2
Symbol
Min
Typ
Max
Units
Internal supply voltage
0.825
0.850
0.876
V
For -1LI and -2LE (VCCINT = 0.72V) devices: internal supply voltage
0.698
0.720
0.742
V
For -3E devices: internal supply voltage
0.873
0.900
0.927
V
Internal supply voltage for the I/O banks
0.825
0.850
0.876
V
For -1LI and -2LE (VCCINT = 0.72V) devices: internal supply voltage
for the I/O banks
0.825
0.850
0.876
V
For -3E devices: internal supply voltage for the I/O banks
0.873
0.900
0.927
V
VCCBRAM
Block RAM supply voltage
0.825
0.850
0.876
V
For -3E devices: block RAM supply voltage
0.873
0.900
0.927
V
VCCAUX
Auxiliary supply voltage
1.746
1.800
1.854
V
VCCO4, 5
Supply voltage for HD I/O banks
1.140
–
3.400
V
FPGA Logic
VCCINT
VCCINT_IO3
Supply voltage for HP I/O banks
0.950
–
1.900
V
VCCAUX_IO6
Auxiliary I/O supply voltage
1.746
1.800
1.854
V
VIN7
I/O input voltage
–0.200
–
VCCO + 0.200
V
IIN8
Maximum current through any pin in a powered or unpowered
bank when forward biasing the clamp diode
–
–
10
mA
VBATT9
Battery voltage
1.000
–
1.890
V
Analog supply voltage for the GTH or GTY transceiver
0.873
0.900
0.927
V
Analog supply voltage for the GTH or GTY transmitter and
receiver termination circuits
1.164
1.200
1.236
V
GTH or GTY Transceiver
VMGTAVCC10
VMGTAVTT
10
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
3
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 2: Recommended Operating Conditions (cont'd)
Description1, 2
Symbol
Min
Typ
Max
Units
Auxiliary analog QPLL voltage supply for the transceivers
1.746
1.800
1.854
V
Analog supply voltage for the resistor calibration circuit of the
GTH or GTY transceiver column
1.164
1.200
1.236
V
VCCADC
System Monitor supply relative to GNDADC
1.746
1.800
1.854
V
VREFP
System Monitor externally supplied reference voltage relative to
GNDADC
1.200
1.250
1.300
V
Junction temperature operating range for extended (E)
temperature devices12
0
–
100
°C
Junction temperature operating range for industrial (I)
temperature devices
–40
–
100
°C
Junction temperature operating range for military (M)
temperature devices
–55
–
125
°C
Junction temperature operating range for eFUSE programming13
–40
–
125
°C
VMGTVCCAUX10
VMGTAVTTRCAL
10
System Monitor
Temperature
Tj11
Notes:
1.
All voltages are relative to GND.
2.
For the design of the power distribution system consult the UltraScale Architecture PCB Design User Guide (UG583).
3.
VCCINT_IO must be connected to VCCBRAM.
4.
For VCCO_0, the minimum recommended operating voltage for power on and during configuration is 1.425V. After configuration, data is
retained even if VCCO drops to 0V.
5.
Includes VCCO of 1.0V (HP I/O only), 1.2V, 1.35V, 1.5V, 1.8V, 2.5V (HD I/O only) at ±5%, and 3.3V (HD I/O only) at +3/–5%.
6.
VCCAUX_IO must be connected to VCCAUX.
7.
The lower absolute voltage specification always applies.
8.
A total of 200 mA per bank should not be exceeded.
9.
If battery is not used, connect VBATT to either GND or VCCAUX.
10. Each voltage listed requires filtering as described in the UltraScale Architecture GTH Transceivers User Guide (UG576) or the UltraScale
Architecture GTY Transceivers User Guide (UG578).
11. Xilinx recommends measuring the Tj of a device using the system monitor as described in the UltraScale Architecture System Monitor User
Guide (UG580). The system monitor temperature measurement errors (that are described in Table 79) must be accounted for in your
design. For example, when using the system monitor with an external reference of 1.25V, and when the system monitor reports 97°C,
there is a measurement error ±3°C. A reading of 97°C is considered the maximum adjusted Tj (100°C – 3°C = 97°C).
12. Devices labeled with the speed/temperature grade of -2LE can operate for a limited time at a junction temperature between 100°C and
110°C. Timing parameters adhere to the same speed file at 110°C as they do below 110°C, regardless of operating voltage (nominal
voltage of 0.85V or a low-voltage of 0.72V). Operation up to Tj = 110°C is limited to 1% of the device lifetime and can occur sequentially or
at regular intervals as long as the total time does not exceed 1% of the device lifetime.
13. Do not program eFUSE during device configuration (e.g., during configuration, during configuration readback, or when readback CRC is
active).
DC Characteristics Over Recommended Operating Conditions
Table 3: DC Characteristics Over Recommended Operating Conditions
Symbol
Description
Min
Typ1
Max
Units
VDRINT
Data retention VCCINT voltage (below which configuration data
might be lost)
0.68
–
–
V
VDRAUX
Data retention VCCAUX voltage (below which configuration data
might be lost)
1.5
–
–
V
IREF
VREF leakage current per pin
–
–
15
µA
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
4
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 3: DC Characteristics Over Recommended Operating Conditions (cont'd)
Symbol
Description
Min
Typ1
Max
Units
IL
Input or output leakage current per pin (HD I/O and HP I/O2)
(sample-tested)
–
–
15
µA
CIN3
Die input capacitance at the pad (HP I/O)
–
–
3.1
pF
Die input capacitance at the pad (HD I/O)
–
–
4.75
pF
Pad pull-up (when selected) at VIN = 0V, VCCO = 3.3V
75
–
190
µA
Pad pull-up (when selected) at VIN = 0V, VCCO = 2.5V
50
–
169
µA
IRPU
IRPD
Pad pull-up (when selected) at VIN = 0V, VCCO = 1.8V
60
–
120
µA
Pad pull-up (when selected) at VIN = 0V, VCCO = 1.5V
30
–
120
µA
Pad pull-up (when selected) at VIN = 0V, VCCO = 1.2V
10
–
100
µA
Pad pull-down (when selected) at VIN = 3.3V
60
–
200
µA
Pad pull-down (when selected) at VIN = 1.8V
29
–
120
µA
ICCADCON
Analog supply current for the SYSMON circuits in the power-up
state
–
–
8
mA
ICCADCOFF
Analog supply current for the SYSMON circuits in the power-down
state
–
–
1.5
mA
IBATT4, 5
Battery supply current at VBATT = 1.89V
–
–
650
nA
Battery supply current at VBATT = 1.20V
–
–
150
nA
IPFS6
VCCAUX additional supply current during eFUSE programming
–
–
115
mA
Calibrated programmable on-die termination (DCI) in HP I/O banks7 (measured per JEDEC specification)
R9
Thevenin equivalent resistance of programmable input
termination to VCCO/2 where ODT = RTT_40
–10%8
40
+10%8
Ω
Thevenin equivalent resistance of programmable input
termination to VCCO/2 where ODT = RTT_48
–10%8
48
+10%8
Ω
Thevenin equivalent resistance of programmable input
termination to VCCO/2 where ODT = RTT_60
–10%8
60
+10%8
Ω
Programmable input termination to VCCO where ODT = RTT_40
–10%8
40
+10%8
Ω
Programmable input termination to VCCO where ODT = RTT_48
–10%8
48
+10%8
Ω
Programmable input termination to VCCO where ODT = RTT_60
–10%8
60
+10%8
Ω
Programmable input termination to VCCO where ODT = RTT_120
–10%8
120
+10%8
Ω
Programmable input termination to VCCOwhere ODT = RTT_240
–10%8
240
+10%8
Ω
Uncalibrated programmable on-die termination in HP I/Os banks (measured per JEDEC specification)
R9
Thevenin equivalent resistance of programmable input
termination to VCCO/2 where ODT = RTT_40
–50%
40
+50%
Ω
Thevenin equivalent resistance of programmable input
termination to VCCO/2 where ODT = RTT_48
–50%
48
+50%
Ω
Thevenin equivalent resistance of programmable input
termination to VCCO/2 where ODT = RTT_60
–50%
60
+50%
Ω
Programmable input termination to VCCO where ODT = RTT_40
–50%
40
+50%
Ω
Programmable input termination to VCCO where ODT = RTT_48
–50%
48
+50%
Ω
Programmable input termination to VCCO where ODT = RTT_60
–50%
60
+50%
Ω
Programmable input termination to VCCO where ODT = RTT_120
–50%
120
+50%
Ω
Programmable input termination to VCCO where ODT = RTT_240
–50%
240
+50%
Ω
48
+50%
Ω
Uncalibrated programmable on-die termination in HD I/O banks (measured per JEDEC specification)
R9
Thevenin equivalent resistance of programmable input
termination to VCCO/2 where ODT = RTT_48
DS922 (v1.17) February 16, 2021
Product Specification
–50%
Send Feedback
www.xilinx.com
5
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 3: DC Characteristics Over Recommended Operating Conditions (cont'd)
Min
Typ1
Max
Units
50% VCCO
VCCO x 0.49
VCCO x 0.50
VCCO x 0.51
V
70% VCCO
VCCO x 0.69
VCCO x 0.70
VCCO x 0.71
V
–35%
100
+35%
Ω
Symbol
Internal VREF
Description
Differential termination
Programmable differential termination (TERM_100) for HP I/O
banks
n
Temperature diode ideality factor
–
1.026
–
–
r
Temperature diode series resistance
–
2
–
Ω
Notes:
1.
Typical values are specified at nominal voltage, 25°C.
2.
For the HP I/O banks with a VCCO of 1.8V and separated VCCO and VCCAUX_IO power supplies, the IL maximum current is 70 µA.
3.
This measurement represents the die capacitance at the pad, not including the package.
4.
Maximum value specified for worst case process at 25°C.
5.
IBATT is measured when the battery-backed RAM (BBRAM) is enabled.
6.
Do not program eFUSE during device configuration (e.g., during configuration, during configuration readback, or when readback CRC is
active).
7.
VRP resistor tolerance is (240Ω ±1%).
8.
If VRP resides at a different bank (DCI cascade), the range increases to ±15%.
9.
On-die input termination resistance, for more information see the UltraScale Architecture SelectIO Resources User Guide (UG571).
VIN Maximum Allowed AC Voltage Overshoot and Undershoot
Table 4: VIN Maximum Allowed AC Voltage Overshoot and Undershoot for HD I/O Banks
AC Voltage Overshoot1
% of UI2 at –40°C to 100°C3
AC Voltage Undershoot1
% of UI2 at –40°C to 100°C
VCCO + 0.30
VCCO + 0.35
100%
–0.30
100%
100%
–0.35
90%
VCCO + 0.40
100%
–0.40
78%
VCCO + 0.45
100%
–0.45
40%
VCCO + 0.50
100%
–0.50
24%
VCCO + 0.55
100%
–0.55
18.0%
VCCO + 0.60
100%
–0.60
13.0%
VCCO + 0.65
100%
–0.65
10.8%
VCCO + 0.70
92%
–0.70
9.0%
VCCO + 0.75
92%
–0.75
7.0%
VCCO + 0.80
92%
–0.80
6.0%
VCCO + 0.85
92%
–0.85
5.0%
VCCO + 0.90
92%
–0.90
4.0%
VCCO + 0.95
92%
–0.95
2.5%
Notes:
1.
A total of 200 mA per bank should not be exceeded.
2.
For UI smaller than 20 µs.
3.
For the -1M devices, the temperature limits are –55°C to 125°C.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
6
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 5: VIN Maximum Allowed AC Voltage Overshoot and Undershoot for HP I/O Banks
AC Voltage Overshoot1
% of UI2 at –40°C to 100°C
AC Voltage Undershoot1
% of UI2 at –40°C to 100°C
VCCO + 0.30
100%
–0.30
100%
VCCO + 0.35
100%
–0.35
100%
VCCO + 0.40
92%
–0.40
92%
VCCO + 0.45
50%
–0.45
50%
VCCO + 0.50
20%
–0.50
20%
VCCO + 0.55
10%
–0.55
10%
VCCO + 0.60
6%
–0.60
6%
VCCO + 0.65
2%
–0.65
2%
VCCO + 0.70
2%
–0.70
2%
Notes:
1.
A total of 200 mA per bank should not be exceeded.
2.
For UI smaller than 20 µs.
3.
For the -1M devices, the temperature limits are –55°C to 125°C.
Quiescent Supply Current
Table 6: Typical Quiescent Supply Current
Speed Grade and VCCINT Operating Voltages
Symbol
ICCINTQ
ICCINT_IOQ
ICCOQ
Description1, 2, 3
Quiescent VCCINT supply current
Quiescent VCCINT_IO supply current
Quiescent VCCO supply current
DS922 (v1.17) February 16, 2021
Product Specification
Device
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
XCKU3P
1242
1181
1181
1037
1037
mA
XCKU5P
1242
1181
1181
1037
1037
mA
XCKU9P
1592
1523
1523
1356
1356
mA
XCKU11P
1780
1693
1693
1486
1486
mA
XCKU13P
1950
1864
1864
1658
1658
mA
XCKU15P
2677
2559
2559
2275
2275
mA
XCKU19P
6784
6480
6480
5758
5758
mA
XQKU5P
N/A
1181
1181
N/A
1037
mA
XQKU15P
N/A
2559
2559
N/A
2275
mA
XCKU3P
61
59
59
59
59
mA
XCKU5P
61
59
59
59
59
mA
XCKU9P
61
59
59
59
59
mA
XCKU11P
120
115
115
115
115
mA
XCKU13P
61
59
59
59
59
mA
XCKU15P
164
158
158
158
158
mA
XCKU19P
234
226
226
226
226
mA
XQKU5P
N/A
59
59
N/A
59
mA
XQKU15P
N/A
158
158
N/A
158
mA
All devices
1
1
1
1
1
mA
Send Feedback
www.xilinx.com
7
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 6: Typical Quiescent Supply Current (cont'd)
Speed Grade and VCCINT Operating Voltages
Symbol
Description1, 2, 3
Device
0.90V
-3
ICCAUXQ
ICCAUX_IOQ
ICCBRAMQ
Quiescent VCCAUX supply current
Quiescent VCCAUX_IO supply current
Quiescent VCCBRAM supply current
0.85V
-2
0.72V
-1
-2
Units
-1
XCKU3P
153
153
153
153
153
mA
XCKU5P
153
153
153
153
153
mA
XCKU9P
227
227
227
227
227
mA
XCKU11P
255
255
255
255
255
mA
XCKU13P
266
266
266
266
266
mA
XCKU15P
396
396
396
396
396
mA
XCKU19P
735
735
735
735
735
mA
XQKU5P
N/A
153
153
N/A
153
mA
XQKU15P
N/A
396
396
N/A
396
mA
XCKU3P
32
32
32
32
32
mA
XCKU5P
32
32
32
32
32
mA
XCKU9P
33
33
33
33
33
mA
XCKU11P
56
56
56
56
56
mA
XCKU13P
33
33
33
33
33
mA
XCKU15P
74
74
74
74
74
mA
XCKU19P
100
100
100
100
100
mA
XQKU5P
N/A
32
32
N/A
32
mA
XQKU15P
N/A
74
74
N/A
74
mA
XCKU3P
18
17
17
17
17
mA
XCKU5P
18
17
17
17
17
mA
XCKU9P
25
24
24
24
24
mA
XCKU11P
23
22
22
22
22
mA
XCKU13P
29
28
28
28
28
mA
XCKU15P
37
35
35
35
35
mA
XCKU19P
66
63
63
63
63
mA
XQKU5P
N/A
17
17
N/A
17
mA
XQKU15P
N/A
74
74
N/A
74
mA
Notes:
1.
Typical values are specified at nominal voltage, 85°C junction temperatures (Tj) with single-ended SelectIO™ resources.
2.
Typical values are for blank configured devices with no output current loads, no active input pull-up resistors, and all I/O pins are 3-state
and floating.
3.
Use the Xilinx® Power Estimator (XPE) spreadsheet tool (download at www.xilinx.com/power) to estimate static power consumption for
conditions or supplies other than those specified.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
8
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Power Supply Sequencing
Power-On/Off Power Supply Sequencing
The recommended power-on sequence is VCCINT, VCCINT_IO/VCCBRAM, VCCAUX/VCCAUX_IO, and VCCO to achieve
minimum current draw and ensure that the I/Os are 3-stated at power-on. The recommended power-off
sequence is the reverse of the power-on sequence. If VCCINT and VCCINT_IO/VCCBRAM have the same
recommended voltage levels, they can be powered by the same supply and ramped simultaneously. VCCINT_IO
must be connected to VCCBRAM. If VCCAUX/VCCAUX_IO and VCCO have the same recommended voltage levels,
they can be powered by the same supply and ramped simultaneously. VCCAUX and VCCAUX_IO must be connected
together. VCCADC and VREF can be powered at any time and have no power-up sequencing requirements.
The recommended power-on sequence to achieve minimum current draw for the GTH or GTY transceivers is
VCCINT, VMGTAVCC, VMGTAVTT OR VMGTAVCC, VCCINT, VMGTAVTT. There is no recommended sequencing for
VMGTVCCAUX. Both VMGTAVCC and VCCINT can be ramped simultaneously. The recommended power-off sequence
is the reverse of the power-on sequence to achieve minimum current draw. If these recommended sequences
are not met, current drawn from VMGTAVTT can be higher than specifications during power-up and power-down.
Power Supply Requirements
Table 7 shows the minimum current, in addition to ICCQ maximum, required by each Kintex UltraScale+ FPGA for
proper power-on and configuration. If these current minimums are met, the device powers on after all supplies
have passed through their power-on reset threshold voltages. The device must not be configured until after
VCCINT is applied. Once initialized and configured, use the Xilinx Power Estimator (XPE) tools to estimate current
drain on these supplies. The XPE spreadsheet tool (download at https://www.xilinx.com/power) is also used to
estimate power-on current for all supplies.
Table 7: Power-on Current by Device
Device
ICCINTMIN
ICCINT_IOMIN + ICCBRAMMIN
ICCOMIN
ICCAUXMIN + ICCAUX_IOMIN
Units
XCKU3P
ICCINTQ + 770
ICCBRAMQ + ICCINT_IOQ + 229
ICCOQ + 50
ICCAUXQ + ICCAUX_IOQ + 386
mA
XCKU5P
XQKU5P
ICCINTQ + 770
ICCBRAMQ + ICCINT_IOQ + 305
ICCOQ + 50
ICCAUXQ + ICCAUX_IOQ + 515
mA
XCKU9P
ICCINTQ + 1800
ICCBRAMQ + ICCINT_IOQ + 600
ICCOQ + 50
ICCAUXQ + ICCAUX_IOQ + 650
mA
XCKU11P
ICCINTQ + 1961
ICCBRAMQ + ICCINT_IOQ + 654
ICCOQ + 55
ICCAUXQ + ICCAUX_IOQ + 709
mA
XCKU13P
ICCINTQ + 2242
ICCBRAMQ + ICCINT_IOQ + 748
ICCOQ + 63
ICCAUXQ + ICCAUX_IOQ + 810
mA
XCKU15P
XQKU15P
ICCINTQ + 3433
ICCBRAMQ + ICCINT_IOQ + 1145
ICCOQ + 96
ICCAUXQ + ICCAUX_IOQ + 1240
mA
XCKU19P
ICCINTQ + 5225
ICCBRAMQ + ICCINT_IOQ + 1751
ICCOQ + 131
ICCAUXQ + ICCAUX_IOQ + 915
mA
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
9
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 8: Power Supply Ramp Time
Symbol
Description
Min
Max
Units
TVCCINT
Ramp time from GND to 95% of VCCINT
0.2
40
ms
TVCCINT_IO
Ramp time from GND to 95% of VCCINT_IO
0.2
40
ms
TVCCO
Ramp time from GND to 95% of VCCO
0.2
40
ms
TVCCAUX
Ramp time from GND to 95% of VCCAUX
0.2
40
ms
TVCCBRAM
Ramp time from GND to 95% of VCCBRAM
0.2
40
ms
TMGTAVCC
Ramp time from GND to 95% of VMGTAVCC
0.2
40
ms
TMGTAVTT
Ramp time from GND to 95% of VMGTAVTT
0.2
40
ms
TMGTVCCAUX
Ramp time from GND to 95% of VMGTVCCAUX
0.2
40
ms
DC Input and Output Levels
Values for VIL and VIH are recommended input voltages. Values for IOL and IOH are guaranteed over the
recommended operating conditions at the VOL and VOH test points. Only selected standards are tested. These
are chosen to ensure that all standards meet their specifications. The selected standards are tested at a
minimum VCCO with the respective VOL and VOH voltage levels shown. Other standards are sample tested.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
10
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
I/O Levels
Table 9: SelectIO DC Input and Output Levels For HD I/O Banks
I/O Standard1, 2
VIL
VIH
VOL
VOH
IOL
IOH
V, Min
V, Max
V, Min
V, Max
V, Max
V, Min
mA
mA
HSTL_I
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
0.400
VCCO – 0.400
8.0
–8.0
HSTL_I_18
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
0.400
VCCO – 0.400
8.0
–8.0
HSUL_12
–0.300
VREF – 0.130
VREF + 0.130
VCCO + 0.300
20% VCCO
80% VCCO
0.1
–0.1
LVCMOS12
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.400
VCCO – 0.400
Note 3
Note 3
LVCMOS15
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.450
VCCO – 0.450
Note 4
Note 4
LVCMOS18
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.450
VCCO – 0.450
Note 4
Note 4
LVCMOS25
–0.300
0.700
1.700
VCCO + 0.300
0.400
VCCO – 0.400
Note 4
Note 4
LVCMOS33
–0.300
0.800
2.000
3.400
0.400
VCCO – 0.400
Note 4
Note 4
LVTTL
–0.300
0.800
2.000
3.400
0.400
2.400
Note 4
Note 4
SSTL12
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
VCCO/2 – 0.150
VCCO/2 + 0.150
14.25
–14.25
SSTL135
–0.300
VREF – 0.090
VREF + 0.090
VCCO + 0.300
VCCO/2 – 0.150
VCCO/2 + 0.150
8.9
–8.9
SSTL135_II
–0.300
VREF – 0.090
VREF + 0.090
VCCO + 0.300
VCCO/2 – 0.150
VCCO/2 + 0.150
13.0
–13.0
SSTL15
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
VCCO/2 – 0.175
VCCO/2 + 0.175
8.9
–8.9
SSTL15_II
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
VCCO/2 – 0.175
VCCO/2 + 0.175
13.0
–13.0
SSTL18_I
–0.300
VREF – 0.125
VREF + 0.125
VCCO + 0.300
VCCO/2 – 0.470
VCCO/2 + 0.470
8.0
–8.0
SSTL18_II
–0.300
VREF – 0.125
VREF + 0.125
VCCO + 0.300
VCCO/2 – 0.600
VCCO/2 + 0.600
13.4
–13.4
Notes:
1.
Tested according to relevant specifications.
2.
Standards specified using the default I/O standard configuration. For details, see the UltraScale Architecture SelectIO Resources User Guide
(UG571).
3.
Supported drive strengths of 4, 8, or 12 mA in HD I/O banks.
4.
Supported drive strengths of 4, 8, 12, or 16 mA in HD I/O banks.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
11
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 10: SelectIO DC Input and Output Levels for HP I/O Banks
I/O Standard1, 2, 3
VIL
VIH
VOL
VOH
IOL
IOH
V, Min
V, Max
V, Min
V, Max
V, Max
V, Min
mA
mA
HSTL_I
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
0.400
VCCO – 0.400
5.8
–5.8
HSTL_I_12
–0.300
VREF – 0.080
VREF + 0.080
VCCO + 0.300
25% VCCO
75% VCCO
4.1
–4.1
HSTL_I_18
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
0.400
VCCO – 0.400
6.2
–6.2
HSUL_12
–0.300
VREF – 0.130
VREF + 0.130
VCCO + 0.300
20% VCCO
80% VCCO
0.1
–0.1
LVCMOS12
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.400
VCCO – 0.400
Note 4
Note 4
LVCMOS15
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.450
VCCO – 0.450
Note 5
Note 5
LVCMOS18
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.450
VCCO – 0.450
Note 5
Note 5
LVDCI_15
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.450
VCCO – 0.450
7.0
–7.0
LVDCI_18
–0.300
35% VCCO
65% VCCO
VCCO + 0.300
0.450
VCCO – 0.450
7.0
–7.0
SSTL12
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
VCCO/2 – 0.150
VCCO/2 + 0.150
8.0
–8.0
SSTL135
–0.300
VREF – 0.090
VREF + 0.090
VCCO + 0.300
VCCO/2 – 0.150
VCCO/2 + 0.150
9.0
–9.0
SSTL15
–0.300
VREF – 0.100
VREF + 0.100
VCCO + 0.300
VCCO/2 – 0.175
VCCO/2 + 0.175
10.0
–10.0
–0.300
VREF – 0.125
VREF + 0.125
VCCO + 0.300
VCCO/2 – 0.470
VCCO/2 + 0.470
7.0
–7.0
0.550
0.8807
VCCO + 0.300
0.050
1.100
0.01
–0.01
SSTL18_I
MIPI_DPHY_
DCI_LP6
–0.300
Notes:
1.
Tested according to relevant specifications.
2.
Standards specified using the default I/O standard configuration. For details, see the UltraScale Architecture SelectIO Resources User Guide
(UG571).
3.
POD10 and POD12 DC input and output levels are shown in Table 11, Table 16, and Table 17.
4.
Supported drive strengths of 2, 4, 6, or 8 mA in HP I/O banks.
5.
Supported drive strengths of 2, 4, 6, 8, or 12 mA in HP I/O banks.
6.
Low-power option for MIPI_DPHY_DCI.
7.
When operating at data rates of 1.5 Gb/s to 2.5 Gb/s, the minimum VIH is 0.790V. These data rates, outlined in Table 25 are supported for
XC devices only.
Table 11: DC Input Levels for Single-ended POD10 and POD12 I/O Standards
I/O Standard1, 2
VIL
VIH
V, Min
V, Max
V, Min
V, Max
POD10
–0.300
VREF – 0.068
VREF + 0.068
VCCO + 0.300
POD12
–0.300
VREF – 0.068
VREF + 0.068
VCCO + 0.300
Notes:
1.
Tested according to relevant specifications.
2.
Standards specified using the default I/O standard configuration. For details, see the UltraScale Architecture SelectIO Resources User Guide
(UG571).
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
12
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 12: Differential SelectIO DC Input and Output Levels
I/O Standard
VICM (V)1
VID (V)2
VILHS3
VIHHS3
VOCM (V)4
VOD (V)5
Min
Typ
Max
Min
Typ
Max
Min
Max
Min
Typ
Max
Min
Typ
Max
SUB_LVDS8
0.500
0.900
1.300
0.070
–
–
–
–
0.700
0.900
1.100
0.100
0.150
0.200
LVPECL
0.300
1.200
1.425
0.100
0.350
0.600
–
–
–
–
–
–
–
–
SLVS_400_18
0.070
0.200
0.330
0.140
–
0.450
–
–
–
–
–
–
–
–
0.070
0.200
0.330
0.140
–
0.450
–
–
–
–
–
–
–
–
0.070
–
0.330
0.070
–
–
–0.040
0.460
0.150
0.200
0.250
0.140
0.200
0.270
SLVS_400_25
MIPI_DPHY_
DCI_HS9, 10
Notes:
1.
VICM is the input common mode voltage.
2.
VID is the input differential voltage (Q – Q).
3.
VIHHS and VILHS are the single-ended input high and low voltages, respectively.
4.
VOCM is the output common mode voltage.
5.
VOD is the output differential voltage (Q – Q).
6.
LVDS_25 is specified in Table 18.
7.
LVDS is specified in Table 19.
8.
Only the SUB_LVDS receiver is supported in HD I/O banks.
9.
High-speed option for MIPI_DPHY_DCI. The VID maximum is aligned with the standard’s specification. A higher VID is acceptable as long
as the VIN specification is also met.
10. When operating at data rates of 1.5 Gb/s to 2.5 Gb/s, the minimum VID is 0.040V. These data rates, outlined in Table 25 are supported for
XC devices only.
Table 13: Complementary Differential SelectIO DC Input and Output Levels for HD I/O Banks
I/O Standard
VICM (V)1
VID (V)2
VOL (V)3
VOH (V)4
IOL
IOH
Min
Typ
Max
Min
Max
Max
Min
mA
mA
DIFF_HSTL_I
0.300
0.750
1.125
0.100
–
0.400
VCCO – 0.400
8.0
–8.0
DIFF_HSTL_I_18
0.300
0.900
1.425
0.100
–
0.400
VCCO – 0.400
8.0
–8.0
DIFF_HSUL_12
0.300
0.600
0.850
0.100
–
20% VCCO
80% VCCO
0.1
–0.1
DIFF_SSTL12
0.300
0.600
0.850
0.100
–
(VCCO/2) – 0.150
(VCCO/2) + 0.150
14.25
–14.25
DIFF_SSTL135
0.300
0.675
1.000
0.100
–
(VCCO/2) – 0.150
(VCCO/2) + 0.150
8.9
–8.9
DIFF_SSTL135_II
0.300
0.675
1.000
0.100
–
(VCCO/2) – 0.150
(VCCO/2) + 0.150
13.0
–13.0
DIFF_SSTL15
0.300
0.750
1.125
0.100
–
(VCCO/2) – 0.175
(VCCO/2) + 0.175
8.9
–8.9
DIFF_SSTL15_II
0.300
0.750
1.125
0.100
–
(VCCO/2) – 0.175
(VCCO/2) + 0.175
13.0
–13.0
DIFF_SSTL18_I
0.300
0.900
1.425
0.100
–
(VCCO/2) – 0.470
(VCCO/2) + 0.470
8.0
–8.0
DIFF_SSTL18_II
0.300
0.900
1.425
0.100
–
(VCCO/2) – 0.600
(VCCO/2) + 0.600
13.4
–13.4
Notes:
1.
VICM is the input common mode voltage.
2.
VID is the input differential voltage.
3.
VOL is the single-ended low-output voltage.
4.
VOH is the single-ended high-output voltage.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
13
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 14: Complementary Differential SelectIO DC Input and Output Levels for HP I/O Banks
I/O Standard1
VICM (V)2
VID (V)3
VOL (V)4
VOH (V)5
IOL
IOH
Min
Typ
Max
Min
Max
Max
Min
mA
mA
0.680
VCCO/2
(VCCO/2) + 0.150
0.100
–
0.400
VCCO – 0.400
5.8
–5.8
DIFF_HSTL_I_12
0.400 x VCCO
VCCO/2
0.600 x VCCO
0.100
–
0.250 x VCCO
0.750 x VCCO
4.1
–4.1
DIFF_HSTL_I_18
(VCCO/2) – 0.175
VCCO/2
(VCCO/2) + 0.175
0.100
–
0.400
VCCO – 0.400
6.2
–6.2
DIFF_HSUL_12
(VCCO/2) – 0.120
VCCO/2
(VCCO/2) + 0.120
0.100
–
20% VCCO
80% VCCO
0.1
–0.1
DIFF_HSTL_I
DIFF_SSTL12
(VCCO/2) – 0.150
VCCO/2
(VCCO/2) + 0.150
0.100
–
(VCCO/2) – 0.150
(VCCO/2) + 0.150
8.0
–8.0
DIFF_SSTL135
(VCCO/2) – 0.150
VCCO/2
(VCCO/2) + 0.150
0.100
–
(VCCO/2) – 0.150
(VCCO/2) + 0.150
9.0
–9.0
DIFF_SSTL15
(VCCO/2) – 0.175
VCCO/2
(VCCO/2) + 0.175
0.100
–
(VCCO/2) – 0.175
(VCCO/2) + 0.175
10.0
–10.0
DIFF_SSTL18_I
(VCCO/2) – 0.175
VCCO/2
(VCCO/2) + 0.175
0.100
–
(VCCO/2) – 0.470
(VCCO/2) + 0.470
7.0
–7.0
Notes:
1.
DIFF_POD10 and DIFF_POD12 HP I/O bank specifications are shown in Table 15, Table 16, Table 17.
2.
VICM is the input common mode voltage.
3.
VID is the input differential voltage.
4.
VOL is the single-ended low-output voltage.
5.
VOH is the single-ended high-output voltage.
Table 15: DC Input Levels for Differential POD10 and POD12 I/O Standards
I/O Standard1, 2
VICM (V)
VID (V)
Min
Typ
Max
Min
Max
DIFF_POD10
0.63
0.70
0.77
0.14
–
DIFF_POD12
0.76
0.84
0.92
0.16
–
Notes:
1.
Tested according to relevant specifications.
2.
Standards specified using the default I/O standard configuration. For details, see the UltraScale Architecture SelectIO Resources User Guide
(UG571).
Table 16: DC Output Levels for Single-ended and Differential POD10 and POD12 Standards
Symbol
Description1, 2
VOUT
Min
Typ
Max
Units
ROL
Pull-down resistance
VOM_DC (as described in Table 17)
36
40
44
Ω
ROH
Pull-up resistance
VOM_DC (as described in Table 17)
36
40
44
Ω
Notes:
1.
Tested according to relevant specifications.
2.
Standards specified using the default I/O standard configuration. For details, see the UltraScale Architecture SelectIO Resources User Guide
(UG571).
Table 17: Definitions for DC Output Levels for Single-ended and Differential POD10 and POD12
Standards
Symbol
VOM_DC
Description
DC output Mid measurement level (for IV curve linearity)
DS922 (v1.17) February 16, 2021
Product Specification
All Speed Grades
Units
0.8 x VCCO
V
Send Feedback
www.xilinx.com
14
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
LVDS DC Specifications (LVDS_25)
The LVDS_25 standard is available in the HD I/O banks. See the UltraScale Architecture SelectIO Resources User
Guide (UG571) for more information.
Table 18: LVDS_25 DC Specifications
Symbol
1
VCCO
DC Parameter
Supply voltage
VIDIFF
Differential input voltage:
(Q – Q), Q = High
VICM
Input common-mode voltage
Min
Typ
Max
Units
2.375
2.500
2.625
V
100
350
6002
mV
0.300
1.200
1.425
V
(Q – Q), Q = High
Notes:
1.
LVDS_25 in HD I/O banks supports inputs only. LVDS_25 inputs without internal termination have no VCCO requirements. Any VCCO can be
chosen as long as the input voltage levels do not violate the Recommended Operating Condition (Table 2) specification for the VIN I/O pin
voltage.
2.
Maximum VIDIFF value is specified for the maximum VICM specification. With a lower VICM, a higher VDIFF is tolerated only when the
recommended operating conditions and overshoot/undershoot VIN specifications are maintained.
LVDS DC Specifications (LVDS)
The LVDS standard is available in the HP I/O banks. See the UltraScale Architecture SelectIO Resources User Guide
(UG571) for more information.
Table 19: LVDS DC Specifications
Symbol
DC Parameter
VCCO1
Supply voltage
VODIFF2
Differential output voltage:
(Q – Q), Q = High
Conditions
Min
Typ
Max
Units
1.710
1.800
1.890
V
RT = 100Ω across Q and Q signals
247
350
454
mV
RT = 100Ω across Q and Q signals
1.000
1.250
1.425
V
100
350
6003
mV
(Q – Q), Q = High
2
VOCM
3
VIDIFF
Output common-mode voltage
Differential input voltage:
(Q – Q), Q = High
(Q – Q), Q = High
VICM_DC4
Input common-mode voltage (DC coupling)
0.300
1.200
1.425
V
VICM_AC5
Input common-mode voltage (AC coupling)
0.600
–
1.100
V
Notes:
1.
In HP I/O banks, when LVDS is used with input-only functionality, it can be placed in a bank where the VCCO levels are different from the
specified level only if internal differential termination is not used. In this scenario, VCCO must be chosen to ensure the input pin voltage
levels do not violate the Recommended Operating Condition (Table 2) specification for the VIN I/O pin voltage.
2.
VOCM and VODIFF values are for LVDS_PRE_EMPHASIS = FALSE.
3.
Maximum VIDIFF value is specified for the maximum VICM specification. With a lower VICM, a higher VDIFF is tolerated only when the
recommended operating conditions and overshoot/undershoot VIN specifications are maintained.
4.
Input common mode voltage for DC coupled configurations. EQUALIZATION = EQ_NONE (Default).
5.
External input common mode voltage specification for AC coupled configurations. EQUALIZATION = EQ_LEVEL0, EQ_LEVEL1, EQ_LEVEL2,
EQ_LEVEL3, EQ_LEVEL4.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
15
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
AC Switching Characteristics
All values represented in this data sheet are based on the speed specifications in the Vivado® Design Suite as
outlined in the following table.
Table 20: Speed Specification Version By Device
2020.2.2
1.28
Device
XCKU3P, XCKU5P, XCKU9P, XCKU11P, XCKU13P, and XCKU15P
XQKU5P, XQKU15P
1.32
XCKU19P
Switching characteristics are specified on a per-speed-grade basis and can be designated as Advance,
Preliminary, or Production. Each designation is defined as follows:
• Advance Product Specification: These specifications are based on simulations only and are typically available
soon after device design specifications are frozen. Although speed grades with this designation are
considered relatively stable and conservative, some under-reporting might still occur.
• Preliminary Product Specification: These specifications are based on complete ES (engineering sample)
silicon characterization. Devices and speed grades with this designation are intended to give a better
indication of the expected performance of production silicon. The probability of under-reporting delays is
greatly reduced as compared to Advance data.
• Product Specification: These specifications are released once enough production silicon of a particular
device family member has been characterized to provide full correlation between specifications and devices
over numerous production lots. There is no under-reporting of delays, and customers receive formal
notification of any subsequent changes. Typically, the slowest speed grades transition to production before
faster speed grades.
Testing of AC Switching Characteristics
Internal timing parameters are derived from measuring internal test patterns. All AC switching characteristics
are representative of worst-case supply voltage and junction temperature conditions.
For more specific, more precise, and worst-case guaranteed data, use the values reported by the static timing
analyzer and back-annotate to the simulation net list. Unless otherwise noted, values apply to all Kintex
UltraScale+ FPGAs.
Speed Grade Designations
Since individual family members are produced at different times, the migration from one category to another
depends completely on the status of the fabrication process for each device. Table 21 correlates the current
status of the Kintex UltraScale+ FPGAs on a per speed grade basis.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
16
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 21: Speed Grade Designations by Device
Device
Speed Grade, Temperature Ranges, and VCCINT Operating Voltages
Advance
XCKU3P
Preliminary
Production
-3E (VCCINT = 0.90V)
-2E (VCCINT = 0.85V), -2I (VCCINT = 0.85V)
-1E (VCCINT = 0.85V), -1I (VCCINT = 0.85V)
-2LE (VCCINT = 0.85V)1, -1LI (VCCINT = 0.85V)1
-2LE (VCCINT = 0.72V)1, -1LI (VCCINT = 0.72V)1
XCKU5P
-3E (VCCINT = 0.90V)
-2E (VCCINT = 0.85V), -2I (VCCINT = 0.85V)
-1E (VCCINT = 0.85V), -1I (VCCINT = 0.85V)
-2LE (VCCINT = 0.85V)1, -1LI (VCCINT = 0.85V)1
-2LE (VCCINT = 0.72V)1, -1LI (VCCINT = 0.72V)1
XCKU9P
-3E (VCCINT = 0.90V)
-2E (VCCINT = 0.85V), -2I (VCCINT = 0.85V)
-1E (VCCINT = 0.85V), -1I (VCCINT = 0.85V)
-2LE (VCCINT = 0.85V)1, -1LI (VCCINT = 0.85V)1
-2LE (VCCINT = 0.72V)1, -1LI (VCCINT = 0.72V)1
XCKU11P
-3E (VCCINT = 0.90V)
-2E (VCCINT = 0.85V), -2I (VCCINT = 0.85V)
-1E (VCCINT = 0.85V), -1I (VCCINT = 0.85V)
-2LE (VCCINT = 0.85V)1, -1LI (VCCINT = 0.85V)1
-2LE (VCCINT = 0.72V)1, -1LI (VCCINT = 0.72V)1
XCKU13P
-3E (VCCINT = 0.90V)
-2E (VCCINT = 0.85V), -2I (VCCINT = 0.85V)
-1E (VCCINT = 0.85V), -1I (VCCINT = 0.85V)
-2LE (VCCINT = 0.85V)1, -1LI (VCCINT = 0.85V)1
-2LE (VCCINT = 0.72V)1, -1LI (VCCINT = 0.72V)1
XCKU15P
-3E (VCCINT = 0.90V)
-2E (VCCINT = 0.85V), -2I (VCCINT = 0.85V)
-1E (VCCINT = 0.85V), -1I (VCCINT = 0.85V)
-2LE (VCCINT = 0.85V)1, -1LI (VCCINT = 0.85V)1
-2LE (VCCINT = 0.72V)1, -1LI (VCCINT = 0.72V)1
XCKU19P
-3E (VCCINT = 0.90V)
-2E (VCCINT = 0.85V), -2I (VCCINT = 0.85V)
-1E (VCCINT = 0.85V), -1I (VCCINT = 0.85V)
-2LE (VCCINT = 0.85V)1, -1LI (VCCINT = 0.85V)1
-2LE (VCCINT = 0.72V)1, -1LI (VCCINT = 0.72V)1
XQKU5P
-2I (VCCINT = 0.85V)
-1I (VCCINT = 0.85V), -1M (VCCINT = 0.85V)
-1LI (VCCINT = 0.85V)1, -1LI (VCCINT = 0.72V)1
XQKU15P
-2I (VCCINT = 0.85V)
-1I (VCCINT = 0.85V), -1M (VCCINT = 0.85V)
-1LI (VCCINT = 0.85V)1, -1LI (VCCINT = 0.72V)1
Notes:
1.
The lowest power -1L and -2L devices, where VCCINT = 0.72V, are listed in the Vivado Design Suite as -1LV and -2LV, respectively.
Otherwise, the -1L and -2L devices, where VCCINT = 0.85V, are listed in the Vivado Design Suite as -1L and -2L, respectively.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
17
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Production Silicon and Software Status
In some cases, a particular family member (and speed grade) is released to production before a speed
specification is released with the correct label (Advance, Preliminary, Production). Any labeling discrepancies are
corrected in subsequent speed specification releases.
Table 22 lists the production released Kintex UltraScale+ FPGA, speed grade, and the minimum corresponding
supported speed specification version and Vivado software revisions. The Vivado software and speed
specifications listed are the minimum releases required for production. All subsequent releases of software and
speed specifications are valid.
Table 22: Kintex UltraScale+ FPGA Device Production Software and Speed Specification Release
Speed Grade and VCCINT Operating Voltages1
Device
0.90V
-3
0.85V
-2
-1
0.72V
-2L
-1L
-2L
-1L
XCKU3P
Vivado tools 2018.1 v1.19
Vivado tools 2017.1 v1.10
Vivado tools 2017.4 v1.17
XCKU5P
Vivado tools 2018.1 v1.19
Vivado tools 2017.1 v1.10
Vivado tools 2017.4 v1.17
XCKU9P
Vivado tools 2018.2.1 v1.21
Vivado tools 2017.1 v1.10
Vivado tools 2017.3.1 v1.16
XCKU11P
Vivado tools 2018.1 v1.19
Vivado tools 2017.3 v1.14
Vivado tools 2017.4.1 v1.18
XCKU13P
Vivado tools 2018.1 v1.19
Vivado tools 2017.2 v1.12
Vivado tools 2017.3.1 v1.16
XCKU15P
Vivado tools 2018.1 v1.19
Vivado tools 2017.2.1 v1.13
Vivado tools 2017.4 v1.17
XCKU19P
Vivado tools 2020.2.2 v1.32
Vivado tools 2020.2.2 v1.32
Vivado tools 2020.2.2 v1.32
XQKU5P
N/A
Vivado tools 2018.3.1 v1.23
N/A
Vivado tools
2018.3.1 v1.23
N/A
Vivado tools
2018.3.1 v1.23
XQKU15P
N/A
Vivado tools 2018.3.1 v1.23
N/A
Vivado tools
2018.3.1 v1.23
N/A
Vivado tools
2018.3.1 v1.23
Notes:
1.
Blank entries indicate a device and/or speed grade in Advance or Preliminary status.
FPGA Logic Performance Characteristics
This section provides the performance characteristics of some common functions and designs implemented in
the Kintex UltraScale+ FPGAs. These values are subject to the same guidelines as the AC Switching
Characteristics section.
In each of the following LVDS performance tables, the I/O bank type is either high performance (HP) or high
density (HD).
In LVDS component mode:
• For the input/output registers in HP I/O banks, the Vivado tools limit clock frequencies to 312.9 MHz for all
speed grades.
• For IDDR in HP I/O banks, Vivado tools limit clock frequencies to 625.0 MHz for all speed grades.
• For ODDR in HP I/O banks, Vivado tools limit clock frequencies to 625.0 MHz for all speed grades.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
18
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 23: LVDS Component Mode Performance
Speed Grade and VCCINT Operating Voltages
I/O
Bank
Type
Description
0.90V
0.85V
-3
-2
0.72V
-1
-2
Units
-1
Min Max Min Max Min Max Min Max Min Max
LVDS TX DDR (OSERDES 4:1, 8:1)
HP
0
1250
0
1250
0
1250
0
1250
0
1250
Mb/s
LVDS TX SDR (OSERDES 2:1, 4:1)
HP
0
625
0
625
0
625
0
625
0
625
Mb/s
LVDS RX DDR (ISERDES 1:4,
1:8)1
LVDS RX DDR
LVDS RX SDR (ISERDES 1:2,
HP
0
1250
0
1250
0
1250
0
1250
0
1250
Mb/s
HD
0
250
0
250
0
250
0
250
0
250
Mb/s
HP
0
625
0
625
0
625
0
625
0
625
Mb/s
HD
0
125
0
125
0
125
0
125
0
125
Mb/s
1:4)1
LVDS RX SDR
Notes:
1.
LVDS receivers are typically bounded with certain applications to achieve maximum performance. Package skews are not included and
should be removed through PCB routing.
Table 24: LVDS Native Mode Performance
Speed Grade and VCCINT Operating Voltages
Description1, 2
DATA_WIDTH
LVDS TX DDR
(TX_BITSLICE)
4
LVDS TX SDR
(TX_BITSLICE)
4
I/O
Bank
Type
HP
8
HP
8
LVDS RX DDR
(RX_BITSLICE)3
4
LVDS RX SDR
(RX_BITSLICE)3
4
HP
8
8
HP
0.90V
0.85V
-3
-2
Min
Max
0.72V
-1
Min
Max
-2
Min
Max
Units
-1
Min
Max
Min
Max
375
1600
375
1600
375
1600
375
1400
375
1260
Mb/s
375
1600
375
1600
375
1600
375
1600
375
1600
Mb/s
187.5
800
187.5
800
187.5
800
187.5
700
187.5
630
Mb/s
187.5
800
187.5
800
187.5
800
187.5
800
187.5
800
Mb/s
375
16004
375
16004
375
16004
375
14004
375
12604
Mb/s
375
16004
375
16004
375
16004
375
16004
375
16004
Mb/s
187.5
800
187.5
800
187.5
800
187.5
700
187.5
630
Mb/s
187.5
800
187.5
800
187.5
800
187.5
800
187.5
800
Mb/s
Notes:
1.
Native mode is supported through the High-Speed SelectIO Interface Wizard available with the Vivado Design Suite. The performance
values assume a source-synchronous interface.
2.
PLL settings can restrict the minimum allowable data rate. For example, when using the PLL with CLKOUTPHY_MODE = VCO_HALF the
minimum frequency is PLL_FVCOMIN/2.
3.
LVDS receivers are typically bounded with certain applications to achieve maximum performance. Package skews are not included and
should be removed through PCB routing.
4.
Asynchronous receiver performance is limited to 1300 Mb/s for -3/-2 speed grades and to 1250 Mb/s for -1 speed grades.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
19
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 25: MIPI D-PHY Performance
Speed Grade and VCCINT Operating Voltages
I/O
Bank
Type
Description
Maximum MIPI D-PHY
transmitter or receiver
data rate per lane
HP
Conditions1
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
XC devices using Vivado tools
2019.2.2 or later
2500
2500
2500
2500
1260
Mb/s
XC devices using Vivado tools
2019.1.1 through 2019.2.1
2500
2500
1260
2500
1260
Mb/s
XC devices using Vivado tools
2019.1 or earlier
1500
1500
1260
1260
1260
Mb/s
XQ devices
1500
1500
1260
1260
1260
Mb/s
Notes:
1.
For applicable conditions, the lower maximum data rate applies.
Table 26: LVDS Native-Mode 1000BASE-X Support
Speed Grade and VCCINT Operating Voltages
Description1
I/O Bank Type
0.90V
-3
1000BASE-X
0.85V
0.72V
-2
-1
HP
-2
-1
Yes
Notes:
1.
1000BASE-X support is based on the IEEE Standard for CSMA/CD Access Method and Physical Layer Specifications (IEEE Std 802.3-2008).
The following table provides the maximum data rates for applicable memory standards using the Kintex
UltraScale+ FPGA memory PHY. Refer to Memory Interfaces for the complete list of memory interface
standards supported and detailed specifications. The final performance of the memory interface is determined
through a complete design implemented in the Vivado Design Suite, following guidelines in the UltraScale
Architecture PCB Design User Guide (UG583), electrical analysis, and characterization of the system.
Table 27: Maximum Physical Interface (PHY) Rate for Memory Interfaces
Memory
Standard
DDR4
Speed Grade and VCCINT Operating Voltages
Packages
All FFV and FFR
packages
SFVB784 and SFRB784
DS922 (v1.17) February 16, 2021
Product Specification
DRAM Type
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
Single rank component
2666
2666
2400
2400
2133
Mb/s
DIMM1, 2, 3
1 rank
2400
2400
2133
2133
1866
Mb/s
2 rank DIMM1, 4
2133
2133
1866
1866
1600
Mb/s
4 rank DIMM1, 5
1600
1600
1333
1333
N/A
Mb/s
Single rank component
2400
2400
2133
2133
1866
Mb/s
1 rank
DIMM1, 2
2133
2133
1866
1866
1600
Mb/s
2 rank
DIMM1, 4
1866
1866
1600
1600
1600
Mb/s
Send Feedback
www.xilinx.com
20
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 27: Maximum Physical Interface (PHY) Rate for Memory Interfaces (cont'd)
Speed Grade and VCCINT Operating Voltages
Memory
Standard
DDR3
Packages
DRAM Type
-3
All FFV and FFR
packages
SFVB784 and SFRB784
SFVB784 and SFRB784
-2
0.72V
-1
-2
Units
-1
2133
2133
2133
2133
1866
Mb/s
1 rank DIMM1, 2
1866
1866
1866
1866
1600
Mb/s
2 rank DIMM1, 4
1600
1600
1600
1600
1333
Mb/s
DIMM1, 5
1066
1066
1066
1066
800
Mb/s
Single rank component
1866
1866
1866
1866
1600
Mb/s
DIMM1, 2
1600
1600
1600
1600
1600
Mb/s
2 rank DIMM1, 4
1600
1600
1600
1600
1333
Mb/s
4 rank DIMM1, 5
1066
1066
1066
1066
800
Mb/s
Single rank component
1866
1866
1866
1866
1600
Mb/s
1 rank
DIMM1, 2
1600
1600
1600
1600
1333
Mb/s
2 rank
DIMM1, 4
1333
1333
1333
1333
1066
Mb/s
4 rank DIMM1, 5
800
800
800
800
606
Mb/s
Single rank component
1600
1600
1600
1600
1600
Mb/s
1 rank
DIMM1, 2
1600
1600
1600
1600
1333
Mb/s
2 rank
DIMM1, 4
1333
1333
1333
1333
1066
Mb/s
4 rank
DIMM1, 5
1 rank
All FFV and FFR
packages
0.85V
Single rank component
4 rank
DDR3L
0.90V
800
800
800
800
606
Mb/s
QDR II+
All
Single rank component6
633
633
600
600
550
MHz
RLDRAM 3
All FFV and FFR
packages
Single rank component
1200
1200
1066
1066
933
MHz
SFVB784 and SFRB784
Single rank component
1066
1066
933
933
800
MHz
QDR IV XP
All
Single rank component
1066
1066
1066
933
933
MHz
LPDDR3
All
Single rank component
1600
1600
1600
1600
1600
Mb/s
Notes:
1.
Dual in-line memory module (DIMM) includes RDIMM, SODIMM, UDIMM, and LRDIMM.
2.
Includes: 1 rank 1 slot, DDP 2 rank, LRDIMM 2 or 4 rank 1 slot.
3.
For the DDR4 DDP components at -3 and -2 (VCCINT = 0.85V) speed grades, the maximum data rate is 2133 Mb/s for six or more DDP
devices. For five or less DDP devices, use the single rank DIMM data rates for the -3 and -2 (VCCINT = 0.85V) speed grades.
4.
Includes: 2 rank 1 slot, 1 rank 2 slot, LRDIMM 2 rank 2 slot.
5.
Includes: 2 rank 2 slot, 4 rank 1 slot.
6.
The QDRII+ performance specifications are for burst-length 4 (BL = 4) implementations.
FPGA Logic Switching Characteristics
The following IOB high-density (HD) and IOB high-performance (HP) tables summarize the values of standardspecific data input delay adjustments, output delays terminating at pads (based on standard) and 3-state delays.
• TINBUF_DELAY_PAD_I is the delay from IOB pad through the input buffer to the I-pin of an IOB pad. The delay
varies depending on the capability of the SelectIO input buffer.
• TOUTBUF_DELAY_O_PAD is the delay from the O pin to the IOB pad through the output buffer of an IOB pad.
The delay varies depending on the capability of the SelectIO output buffer.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
21
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
• TOUTBUF_DELAY_TD_PAD is the delay from the T pin to the IOB pad through the output buffer of an IOB pad,
when 3-state is disabled. The delay varies depending on the SelectIO capability of the output buffer. In HP
I/O banks, the internal DCI termination turn-on time is always faster than TOUTBUF_DELAY_TD_PAD when the
DCITERMDISABLE pin is used. In HD I/O banks, the on-die termination turn-on time is always faster than
TOUTBUF_DELAY_TD_PAD when the INTERMDISABLE pin is used.
IOB High Density (HD) Switching Characteristics
Table 28: IOB High Density (HD) Switching Characteristics
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_O_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
0.72V
-2
Units
-1
DIFF_HSTL_I_18_F
0.873
0.978 1.058 0.978 1.058
1.510
1.574 1.718 1.966 2.101
1.160
1.160 1.271 1.515 1.544
ns
DIFF_HSTL_I_18_S
0.873
0.978 1.058 0.978 1.058
1.742
1.805 1.950 2.197 2.333
1.748
1.748 1.867 2.103 2.104
ns
DIFF_HSTL_I_F
0.873
0.978 1.058 0.978 1.058
1.563
1.611 1.762 2.003 2.145
1.313
1.313 1.417 1.668 1.668
ns
DIFF_HSTL_I_S
0.873
0.978 1.058 0.978 1.058
1.696
1.798 1.913 2.190 2.296
1.630
1.630 1.780 1.985 1.986
ns
DIFF_HSUL_12_F
0.796
0.911 0.977 0.911 0.977
1.493
1.573 1.703 1.965 2.086
1.222
1.222 1.335 1.577 1.578
ns
DIFF_HSUL_12_S
0.796
0.911 0.977 0.911 0.977
1.653
1.711 1.864 2.103 2.247
1.536
1.536 1.665 1.891 1.891
ns
DIFF_SSTL12_F
0.796
0.906 0.977 0.906 0.977
1.577
1.643 1.792 2.035 2.175
1.285
1.285 1.423 1.640 1.640
ns
DIFF_SSTL12_S
0.796
0.906 0.977 0.906 0.977
1.726
1.784 1.948 2.176 2.331
1.567
1.567 1.706 1.922 1.922
ns
DIFF_SSTL135_F
0.807
0.927 0.995 0.927 0.995
1.558
1.625 1.765 2.017 2.148
1.341
1.341 1.458 1.696 1.696
ns
DIFF_SSTL135_II_F
0.807
0.927 0.995 0.927 0.995
1.560
1.623 1.770 2.015 2.153
1.325
1.325 1.470 1.680 1.689
ns
DIFF_SSTL135_II_S
0.807
0.927 0.995 0.927 0.995
1.694
1.768 1.916 2.160 2.299
1.722
1.722 1.911 2.077 2.078
ns
DIFF_SSTL135_S
0.807
0.927 0.995 0.927 0.995
1.796
1.869 2.025 2.261 2.408
1.814
1.814 1.976 2.169 2.169
ns
DIFF_SSTL15_F
0.840
0.928 1.020 0.928 1.020
1.559
1.628 1.771 2.020 2.154
1.374
1.374 1.483 1.729 1.729
ns
DIFF_SSTL15_II_F
0.840
0.928 1.020 0.928 1.020
1.574
1.622 1.778 2.014 2.161
1.356
1.356 1.442 1.711 1.712
ns
DIFF_SSTL15_II_S
0.840
0.928 1.020 0.928 1.020
1.769
1.821 1.987 2.213 2.370
1.895
1.895 2.047 2.250 2.250
ns
DIFF_SSTL15_S
0.840
0.928 1.020 0.928 1.020
1.752
1.824 1.977 2.216 2.360
1.743
1.743 1.907 2.098 2.098
ns
DIFF_SSTL18_II_F
0.873
0.961 1.038 0.961 1.038
1.672
1.729 1.880 2.121 2.263
1.377
1.377 1.492 1.732 1.732
ns
DIFF_SSTL18_II_S
0.873
0.961 1.038 0.961 1.038
1.748
1.796 1.965 2.188 2.348
1.616
1.616 1.800 1.971 1.972
ns
DIFF_SSTL18_I_F
0.873
0.961 1.038 0.961 1.038
1.539
1.609 1.755 2.001 2.138
1.220
1.220 1.313 1.575 1.575
ns
DIFF_SSTL18_I_S
0.873
0.961 1.038 0.961 1.038
1.728
1.786 1.942 2.178 2.325
1.677
1.677 1.836 2.032 2.033
ns
HSTL_I_18_F
0.854
0.947 1.021 0.947 1.021
1.510
1.574 1.718 1.966 2.101
1.160
1.160 1.271 1.515 1.544
ns
HSTL_I_18_S
0.854
0.947 1.021 0.947 1.021
1.742
1.805 1.950 2.197 2.333
1.748
1.748 1.867 2.103 2.104
ns
HSTL_I_F
0.748
0.856 0.900 0.856 0.900
1.563
1.611 1.762 2.003 2.145
1.313
1.313 1.417 1.668 1.668
ns
HSTL_I_S
0.748
0.856 0.900 0.856 0.900
1.696
1.798 1.913 2.190 2.296
1.630
1.630 1.780 1.985 1.986
ns
HSUL_12_F
0.712
0.780 0.867 0.780 0.867
1.493
1.573 1.703 1.965 2.086
1.222
1.222 1.335 1.577 1.578
ns
HSUL_12_S
0.712
0.780 0.867 0.780 0.867
1.653
1.711 1.864 2.103 2.247
1.536
1.536 1.665 1.891 1.891
ns
LVCMOS12_F_12
0.761
0.918 0.976 0.918 0.976
1.652
1.689 1.856 2.081 2.239
1.202
1.202 1.317 1.557 1.557
ns
LVCMOS12_F_4
0.761
0.918 0.976 0.918 0.976
1.714
1.742 1.922 2.134 2.305
1.353
1.353 1.478 1.708 1.708
ns
LVCMOS12_F_8
0.761
0.918 0.976 0.918 0.976
1.668
1.714 1.879 2.106 2.262
1.292
1.292 1.432 1.647 1.647
ns
LVCMOS12_S_12
0.761
0.918 0.976 0.918 0.976
2.019
2.073 2.247 2.465 2.630
1.581
1.581 1.717 1.936 1.937
ns
LVCMOS12_S_4
0.761
0.918 0.976 0.918 0.976
1.979
1.979 2.182 2.371 2.565
1.633
1.633 1.772 1.988 1.989
ns
LVCMOS12_S_8
0.761
0.918 0.976 0.918 0.976
2.132
2.205 2.406 2.597 2.789
1.767
1.767 1.928 2.122 2.123
ns
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
22
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 28: IOB High Density (HD) Switching Characteristics (cont'd)
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_O_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
0.72V
-2
Units
-1
LVCMOS15_F_12
0.775
0.905 0.958 0.905 0.958
1.691
1.713 1.892 2.105 2.275
1.275
1.275 1.428 1.630 1.630
ns
LVCMOS15_F_16
0.775
0.905 0.958 0.905 0.958
1.665
1.722 1.881 2.114 2.264
1.260
1.260 1.407 1.615 1.615
ns
LVCMOS15_F_4
0.775
0.905 0.958 0.905 0.958
1.747
1.825 1.959 2.217 2.342
1.453
1.453 1.557 1.808 1.809
ns
LVCMOS15_F_8
0.775
0.905 0.958 0.905 0.958
1.721
1.778 1.930 2.170 2.313
1.378
1.378 1.458 1.733 1.733
ns
LVCMOS15_S_12
0.775
0.905 0.958 0.905 0.958
1.936
1.991 2.139 2.383 2.522
1.516
1.516 1.648 1.871 1.871
ns
LVCMOS15_S_16
0.775
0.905 0.958 0.905 0.958
2.172
2.172 2.389 2.564 2.772
1.707
1.707 1.888 2.062 2.062
ns
LVCMOS15_S_4
0.775
0.905 0.958 0.905 0.958
2.274
2.313 2.483 2.705 2.866
1.952
1.952 2.123 2.307 2.307
ns
LVCMOS15_S_8
0.775
0.905 0.958 0.905 0.958
2.170
2.170 2.400 2.562 2.783
1.817
1.817 1.984 2.172 2.173
ns
LVCMOS18_F_12
0.810
0.915 0.958 0.915 0.958
1.741
1.805 1.962 2.197 2.345
1.383
1.383 1.471 1.738 1.738
ns
LVCMOS18_F_16
0.810
0.915 0.958 0.915 0.958
1.698
1.785 1.917 2.177 2.300
1.338
1.338 1.446 1.693 1.693
ns
LVCMOS18_F_4
0.810
0.915 0.958 0.915 0.958
1.815
1.868 2.013 2.260 2.396
1.472
1.472 1.599 1.827 1.832
ns
LVCMOS18_F_8
0.810
0.915 0.958 0.915 0.958
1.785
1.797 1.979 2.189 2.362
1.384
1.384 1.487 1.739 1.739
ns
LVCMOS18_S_12
0.810
0.915 0.958 0.915 0.958
2.163
2.201 2.408 2.593 2.791
1.762
1.762 1.894 2.117 2.118
ns
LVCMOS18_S_16
0.810
0.915 0.958 0.915 0.958
2.102
2.173 2.362 2.565 2.745
1.702
1.702 1.834 2.057 2.057
ns
LVCMOS18_S_4
0.810
0.915 0.958 0.915 0.958
2.342
2.346 2.567 2.738 2.950
1.951
1.951 2.092 2.306 2.306
ns
LVCMOS18_S_8
0.810
0.915 0.958 0.915 0.958
2.275
2.292 2.511 2.684 2.894
1.848
1.848 2.008 2.203 2.204
ns
LVCMOS25_F_12
0.963
0.988 1.042 0.988 1.042
2.153
2.153 2.453 2.545 2.836
1.692
1.692 1.856 2.047 2.047
ns
LVCMOS25_F_16
0.963
0.988 1.042 0.988 1.042
2.105
2.105 2.406 2.497 2.789
1.623
1.623 1.786 1.978 1.979
ns
LVCMOS25_F_4
0.963
0.988 1.042 0.988 1.042
2.317
2.344 2.554 2.736 2.937
1.842
1.842 2.039 2.197 2.197
ns
LVCMOS25_F_8
0.963
0.988 1.042 0.988 1.042
2.184
2.184 2.516 2.576 2.899
1.726
1.726 1.910 2.081 2.081
ns
LVCMOS25_S_12
0.963
0.988 1.042 0.988 1.042
2.550
2.558 2.840 2.950 3.223
1.971
1.971 2.194 2.326 2.327
ns
LVCMOS25_S_16
0.963
0.988 1.042 0.988 1.042
2.449
2.449 2.740 2.841 3.123
1.852
1.852 2.063 2.207 2.207
ns
LVCMOS25_S_4
0.963
0.988 1.042 0.988 1.042
2.770
2.770 3.066 3.162 3.449
2.224
2.224 2.458 2.579 2.579
ns
LVCMOS25_S_8
0.963
0.988 1.042 0.988 1.042
2.663
2.663 2.963 3.055 3.346
2.091
2.091 2.373 2.446 2.446
ns
LVCMOS33_F_12
1.154
1.154 1.213 1.154 1.213
2.415
2.415 2.651 2.807 3.034
1.754
1.754 1.915 2.109 2.109
ns
LVCMOS33_F_16
1.154
1.154 1.213 1.154 1.213
2.381
2.383 2.603 2.775 2.986
1.734
1.734 1.869 2.089 2.089
ns
LVCMOS33_F_4
1.154
1.154 1.213 1.154 1.213
2.541
2.541 2.765 2.933 3.148
1.932
1.932 2.135 2.287 2.287
ns
LVCMOS33_F_8
1.154
1.154 1.213 1.154 1.213
2.603
2.603 2.822 2.995 3.205
1.937
1.937 2.130 2.292 2.294
ns
LVCMOS33_S_12
1.154
1.154 1.213 1.154 1.213
2.705
2.705 3.047 3.097 3.430
2.049
2.049 2.318 2.404 2.404
ns
LVCMOS33_S_16
1.154
1.154 1.213 1.154 1.213
2.714
2.714 3.024 3.106 3.407
2.028
2.028 2.232 2.383 2.383
ns
LVCMOS33_S_4
1.154
1.154 1.213 1.154 1.213
2.999
2.999 3.340 3.391 3.723
2.320
2.320 2.610 2.675 2.675
ns
LVCMOS33_S_8
1.154
1.154 1.213 1.154 1.213
2.929
2.929 3.260 3.321 3.643
2.260
2.260 2.532 2.615 2.616
ns
LVDS_25
0.980
1.003 1.116 1.003 1.116
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
ns
LVPECL
0.980
1.003 1.116 1.003 1.116
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
ns
LVTTL_F_12
1.164
1.164 1.223 1.164 1.223
2.415
2.415 2.651 2.807 3.034
1.754
1.754 1.915 2.109 2.109
ns
LVTTL_F_16
1.164
1.164 1.223 1.164 1.223
2.464
2.464 2.732 2.856 3.115
1.750
1.750 1.986 2.105 2.117
ns
LVTTL_F_4
1.164
1.164 1.223 1.164 1.223
2.541
2.541 2.765 2.933 3.148
1.932
1.932 2.135 2.287 2.287
ns
LVTTL_F_8
1.164
1.164 1.223 1.164 1.223
2.582
2.582 2.787 2.974 3.170
1.910
1.910 2.063 2.265 2.265
ns
LVTTL_S_12
1.164
1.164 1.223 1.164 1.223
2.731
2.731 3.075 3.123 3.458
2.072
2.072 2.343 2.427 2.427
ns
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
23
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 28: IOB High Density (HD) Switching Characteristics (cont'd)
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
TOUTBUF_DELAY_O_PAD
0.72V
-1
-2
0.90V
-1
0.85V
-3
-2
TOUTBUF_DELAY_TD_PAD
0.72V
-1
-2
0.90V
-1
0.85V
-3
-2
0.72V
-1
-2
Units
-1
LVTTL_S_16
1.164
1.164 1.223 1.164 1.223
2.714
2.714 3.024 3.106 3.407
2.028
2.028 2.232 2.383 2.383
ns
LVTTL_S_4
1.164
1.164 1.223 1.164 1.223
2.999
2.999 3.340 3.391 3.723
2.320
2.320 2.610 2.675 2.675
ns
LVTTL_S_8
1.164
1.164 1.223 1.164 1.223
2.929
2.929 3.260 3.321 3.643
2.260
2.260 2.532 2.615 2.616
ns
SLVS_400_25
0.998
1.020 1.136 1.020 1.136
N/A
SSTL12_F
0.712
0.780 0.867 0.780 0.867
1.577
1.643 1.792 2.035 2.175
1.285
1.285 1.423 1.640 1.640
ns
SSTL12_S
0.712
0.780 0.867 0.780 0.867
1.726
1.784 1.948 2.176 2.331
1.567
1.567 1.706 1.922 1.922
ns
SSTL135_F
0.731
0.798 0.881 0.798 0.881
1.558
1.625 1.765 2.017 2.148
1.341
1.341 1.458 1.696 1.696
ns
SSTL135_II_F
0.731
0.798 0.881 0.798 0.881
1.574
1.623 1.770 2.015 2.153
1.325
1.325 1.470 1.680 1.689
ns
SSTL135_II_S
0.731
0.798 0.881 0.798 0.881
1.694
1.768 1.916 2.160 2.299
1.722
1.722 1.911 2.077 2.078
ns
SSTL135_S
0.731
0.798 0.881 0.798 0.881
1.796
1.869 2.025 2.261 2.408
1.814
1.814 1.976 2.169 2.169
ns
SSTL15_F
0.731
0.838 0.880 0.838 0.880
1.544
1.612 1.754 2.004 2.137
1.357
1.357 1.464 1.712 1.713
ns
SSTL15_II_F
0.731
0.838 0.880 0.838 0.880
1.588
1.622 1.778 2.014 2.161
1.356
1.356 1.442 1.711 1.712
ns
SSTL15_II_S
0.731
0.838 0.880 0.838 0.880
1.769
1.821 1.987 2.213 2.370
1.895
1.895 2.047 2.250 2.250
ns
SSTL15_S
0.731
0.838 0.880 0.838 0.880
1.752
1.824 1.977 2.216 2.360
1.743
1.743 1.907 2.098 2.098
ns
SSTL18_II_F
0.854
0.947 1.021 0.947 1.021
1.699
1.729 1.880 2.121 2.263
1.377
1.377 1.492 1.732 1.732
ns
SSTL18_II_S
0.854
0.947 1.021 0.947 1.021
1.748
1.796 1.965 2.188 2.348
1.616
1.616 1.800 1.971 1.972
ns
SSTL18_I_F
0.854
0.947 1.021 0.947 1.021
1.566
1.609 1.755 2.001 2.138
1.220
1.220 1.313 1.575 1.575
ns
SSTL18_I_S
0.854
0.947 1.021 0.947 1.021
1.745
1.786 1.942 2.178 2.325
1.677
1.677 1.836 2.032 2.033
ns
SUB_LVDS
0.871
1.002 1.036 1.002 1.036
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
ns
ns
IOB High Performance (HP) Switching Characteristics
Table 29: IOB High Performance (HP) Switching Characteristics
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_O_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
0.72V
-2
Units
-1
DIFF_HSTL_I_12_F
0.288
0.394 0.402 0.394 0.402
0.410
0.423 0.443 0.423 0.443
0.514
0.553 0.582 0.553 0.582
ns
DIFF_HSTL_I_12_M
0.288
0.394 0.402 0.394 0.402
0.552
0.552 0.583 0.552 0.583
0.632
0.641 0.679 0.641 0.679
ns
DIFF_HSTL_I_12_S
0.288
0.394 0.402 0.394 0.402
0.752
0.752 0.800 0.752 0.800
0.813
0.813 0.868 0.813 0.868
ns
DIFF_HSTL_I_18_F
0.259
0.319 0.339 0.319 0.339
0.439
0.456 0.474 0.456 0.474
0.549
0.576 0.606 0.576 0.606
ns
DIFF_HSTL_I_18_M
0.259
0.319 0.339 0.319 0.339
0.563
0.570 0.603 0.570 0.603
0.636
0.653 0.692 0.653 0.692
ns
DIFF_HSTL_I_18_S
0.259
0.319 0.339 0.319 0.339
0.782
0.782 0.834 0.782 0.834
0.816
0.816 0.871 0.816 0.871
ns
DIFF_HSTL_I_DCI_12_F
0.288
0.394 0.402 0.394 0.402
0.393
0.406 0.429 0.406 0.429
0.502
0.534 0.564 0.534 0.564
ns
DIFF_HSTL_I_DCI_12_M
0.288
0.394 0.402 0.394 0.402
0.546
0.557 0.587 0.557 0.587
0.636
0.653 0.694 0.653 0.694
ns
DIFF_HSTL_I_DCI_12_S
0.288
0.394 0.402 0.394 0.402
0.755
0.755 0.806 0.755 0.806
0.842
0.842 0.907 0.842 0.907
ns
DIFF_HSTL_I_DCI_18_F
0.259
0.323 0.339 0.323 0.339
0.422
0.445 0.461 0.445 0.461
0.509
0.566 0.595 0.566 0.595
ns
DIFF_HSTL_I_DCI_18_M
0.259
0.323 0.339 0.323 0.339
0.546
0.555 0.586 0.555 0.586
0.626
0.643 0.684 0.643 0.684
ns
DIFF_HSTL_I_DCI_18_S
0.259
0.323 0.339 0.323 0.339
0.762
0.762 0.818 0.762 0.818
0.836
0.836 0.900 0.836 0.900
ns
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
24
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 29: IOB High Performance (HP) Switching Characteristics (cont'd)
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_O_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
0.72V
-2
Units
-1
DIFF_HSTL_I_DCI_F
0.335
0.397 0.417 0.397 0.417
0.407
0.431 0.445 0.431 0.445
0.517
0.555 0.575 0.555 0.575
ns
DIFF_HSTL_I_DCI_M
0.335
0.397 0.417 0.397 0.417
0.549
0.553 0.583 0.553 0.583
0.634
0.644 0.684 0.644 0.684
ns
DIFF_HSTL_I_DCI_S
0.335
0.397 0.417 0.397 0.417
0.767
0.767 0.823 0.767 0.823
0.848
0.848 0.912 0.848 0.912
ns
DIFF_HSTL_I_F
0.304
0.404 0.417 0.404 0.417
0.409
0.423 0.443 0.423 0.443
0.514
0.549 0.581 0.549 0.581
ns
DIFF_HSTL_I_M
0.304
0.404 0.417 0.404 0.417
0.549
0.555 0.586 0.555 0.586
0.624
0.640 0.677 0.640 0.677
ns
DIFF_HSTL_I_S
0.304
0.404 0.417 0.404 0.417
0.767
0.767 0.818 0.767 0.818
0.811
0.811 0.866 0.811 0.866
ns
DIFF_HSUL_12_DCI_F
0.320
0.381 0.400 0.381 0.400
0.411
0.425 0.443 0.425 0.443
0.520
0.558 0.586 0.558 0.586
ns
DIFF_HSUL_12_DCI_M
0.320
0.381 0.400 0.381 0.400
0.546
0.557 0.587 0.557 0.587
0.636
0.653 0.694 0.653 0.694
ns
DIFF_HSUL_12_DCI_S
0.320
0.381 0.400 0.381 0.400
0.737
0.737 0.787 0.737 0.787
0.822
0.822 0.885 0.822 0.885
ns
DIFF_HSUL_12_F
0.322
0.394 0.402 0.394 0.402
0.394
0.412 0.430 0.412 0.430
0.494
0.538 0.566 0.538 0.566
ns
DIFF_HSUL_12_M
0.322
0.394 0.402 0.394 0.402
0.552
0.552 0.583 0.552 0.583
0.632
0.641 0.679 0.641 0.679
ns
DIFF_HSUL_12_S
0.322
0.394 0.402 0.394 0.402
0.752
0.752 0.800 0.752 0.800
0.813
0.813 0.868 0.813 0.868
ns
DIFF_POD10_DCI_F
0.289
0.411 0.430 0.411 0.430
0.407
0.425 0.444 0.425 0.444
0.512
0.555 0.584 0.555 0.584
ns
DIFF_POD10_DCI_M
0.289
0.411 0.430 0.411 0.430
0.533
0.542 0.571 0.542 0.571
0.618
0.640 0.681 0.640 0.681
ns
DIFF_POD10_DCI_S
0.289
0.411 0.430 0.411 0.430
0.754
0.754 0.815 0.754 0.815
0.850
0.850 0.917 0.850 0.917
ns
DIFF_POD10_F
0.288
0.411 0.433 0.411 0.433
0.425
0.438 0.459 0.438 0.459
0.531
0.569 0.601 0.569 0.601
ns
DIFF_POD10_M
0.288
0.411 0.433 0.411 0.433
0.519
0.538 0.568 0.538 0.568
0.589
0.630 0.667 0.630 0.667
ns
DIFF_POD10_S
0.288
0.411 0.433 0.411 0.433
0.752
0.766 0.821 0.766 0.821
0.821
0.836 0.894 0.836 0.894
ns
DIFF_POD12_DCI_F
0.320
0.407 0.432 0.407 0.432
0.411
0.425 0.443 0.425 0.443
0.519
0.558 0.586 0.558 0.586
ns
DIFF_POD12_DCI_M
0.320
0.407 0.432 0.407 0.432
0.516
0.543 0.572 0.543 0.572
0.602
0.638 0.678 0.638 0.678
ns
DIFF_POD12_DCI_S
0.320
0.407 0.432 0.407 0.432
0.740
0.772 0.822 0.772 0.822
0.833
0.862 0.929 0.862 0.929
ns
DIFF_POD12_F
0.305
0.409 0.430 0.409 0.430
0.438
0.455 0.476 0.455 0.476
0.549
0.595 0.626 0.595 0.626
ns
DIFF_POD12_M
0.305
0.409 0.430 0.409 0.430
0.551
0.551 0.582 0.551 0.582
0.632
0.641 0.679 0.641 0.679
ns
DIFF_POD12_S
0.305
0.409 0.430 0.409 0.430
0.749
0.767 0.817 0.767 0.817
0.818
0.832 0.889 0.832 0.889
ns
DIFF_SSTL12_DCI_F
0.303
0.381 0.400 0.381 0.400
0.411
0.425 0.443 0.425 0.443
0.520
0.558 0.586 0.558 0.586
ns
DIFF_SSTL12_DCI_M
0.303
0.381 0.400 0.381 0.400
0.549
0.557 0.587 0.557 0.587
0.643
0.654 0.694 0.654 0.694
ns
DIFF_SSTL12_DCI_S
0.303
0.381 0.400 0.381 0.400
0.754
0.754 0.803 0.754 0.803
0.842
0.842 0.908 0.842 0.908
ns
DIFF_SSTL12_F
0.288
0.394 0.402 0.394 0.402
0.394
0.412 0.430 0.412 0.430
0.494
0.538 0.566 0.538 0.566
ns
DIFF_SSTL12_M
0.288
0.394 0.402 0.394 0.402
0.550
0.553 0.584 0.553 0.584
0.630
0.641 0.676 0.641 0.676
ns
DIFF_SSTL12_S
0.288
0.394 0.402 0.394 0.402
0.758
0.758 0.808 0.758 0.808
0.823
0.823 0.879 0.823 0.879
ns
DIFF_SSTL135_DCI_F
0.303
0.371 0.402 0.371 0.402
0.392
0.411 0.428 0.411 0.428
0.494
0.537 0.565 0.537 0.565
ns
DIFF_SSTL135_DCI_M
0.303
0.371 0.402 0.371 0.402
0.551
0.551 0.582 0.551 0.582
0.643
0.645 0.685 0.645 0.685
ns
DIFF_SSTL135_DCI_S
0.303
0.371 0.402 0.371 0.402
0.746
0.746 0.799 0.746 0.799
0.829
0.829 0.893 0.829 0.893
ns
DIFF_SSTL135_F
0.289
0.375 0.402 0.375 0.402
0.393
0.408 0.428 0.408 0.428
0.491
0.528 0.561 0.528 0.561
ns
DIFF_SSTL135_M
0.289
0.375 0.402 0.375 0.402
0.548
0.555 0.585 0.555 0.585
0.621
0.641 0.679 0.641 0.679
ns
DIFF_SSTL135_S
0.289
0.375 0.402 0.375 0.402
0.772
0.772 0.823 0.772 0.823
0.827
0.827 0.878 0.827 0.878
ns
DIFF_SSTL15_DCI_F
0.335
0.397 0.417 0.397 0.417
0.394
0.412 0.429 0.412 0.429
0.497
0.531 0.563 0.531 0.563
ns
DIFF_SSTL15_DCI_M
0.335
0.397 0.417 0.397 0.417
0.549
0.553 0.583 0.553 0.583
0.632
0.645 0.685 0.645 0.685
ns
DIFF_SSTL15_DCI_S
0.335
0.397 0.417 0.397 0.417
0.768
0.768 0.822 0.768 0.822
0.847
0.847 0.912 0.847 0.912
ns
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
25
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 29: IOB High Performance (HP) Switching Characteristics (cont'd)
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_O_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
0.72V
-2
Units
-1
DIFF_SSTL15_F
0.304
0.404 0.417 0.404 0.417
0.409
0.424 0.445 0.424 0.445
0.513
0.551 0.577 0.551 0.577
ns
DIFF_SSTL15_M
0.304
0.404 0.417 0.404 0.417
0.547
0.554 0.585 0.554 0.585
0.624
0.639 0.677 0.639 0.677
ns
DIFF_SSTL15_S
0.304
0.404 0.417 0.404 0.417
0.767
0.767 0.817 0.767 0.817
0.813
0.813 0.867 0.813 0.867
ns
DIFF_SSTL18_I_DCI_F
0.256
0.320 0.336 0.320 0.336
0.422
0.445 0.461 0.445 0.461
0.540
0.566 0.595 0.566 0.595
ns
DIFF_SSTL18_I_DCI_M
0.256
0.320 0.336 0.320 0.336
0.552
0.554 0.585 0.554 0.585
0.629
0.644 0.683 0.644 0.683
ns
DIFF_SSTL18_I_DCI_S
0.256
0.320 0.336 0.320 0.336
0.762
0.762 0.818 0.762 0.818
0.837
0.837 0.899 0.837 0.899
ns
DIFF_SSTL18_I_F
0.256
0.316 0.336 0.316 0.336
0.439
0.454 0.476 0.454 0.476
0.549
0.578 0.608 0.578 0.608
ns
DIFF_SSTL18_I_M
0.256
0.316 0.336 0.316 0.336
0.567
0.571 0.603 0.571 0.603
0.535
0.652 0.692 0.652 0.692
ns
DIFF_SSTL18_I_S
0.256
0.316 0.336 0.316 0.336
0.782
0.782 0.835 0.782 0.835
0.816
0.816 0.870 0.816 0.870
ns
HSLVDCI_15_F
0.336
0.393 0.415 0.393 0.415
0.407
0.425 0.443 0.425 0.443
0.513
0.548 0.579 0.548 0.579
ns
HSLVDCI_15_M
0.336
0.393 0.415 0.393 0.415
0.548
0.552 0.581 0.552 0.581
0.635
0.644 0.684 0.644 0.684
ns
HSLVDCI_15_S
0.336
0.393 0.415 0.393 0.415
0.748
0.748 0.802 0.748 0.802
0.827
0.827 0.890 0.827 0.890
ns
HSLVDCI_18_F
0.367
0.424 0.447 0.424 0.447
0.424
0.445 0.461 0.445 0.461
0.541
0.566 0.595 0.566 0.595
ns
HSLVDCI_18_M
0.367
0.424 0.447 0.424 0.447
0.563
0.567 0.598 0.567 0.598
0.647
0.658 0.699 0.658 0.699
ns
HSLVDCI_18_S
0.367
0.424 0.447 0.424 0.447
0.761
0.761 0.817 0.761 0.817
0.836
0.836 0.900 0.836 0.900
ns
HSTL_I_12_F
0.322
0.378 0.399 0.378 0.399
0.410
0.423 0.443 0.423 0.443
0.514
0.553 0.582 0.553 0.582
ns
HSTL_I_12_M
0.322
0.378 0.399 0.378 0.399
0.551
0.551 0.582 0.551 0.582
0.632
0.642 0.679 0.642 0.679
ns
HSTL_I_12_S
0.322
0.378 0.399 0.378 0.399
0.750
0.750 0.799 0.750 0.799
0.813
0.813 0.868 0.813 0.868
ns
HSTL_I_18_F
0.258
0.322 0.339 0.322 0.339
0.439
0.456 0.474 0.456 0.474
0.549
0.576 0.606 0.576 0.606
ns
HSTL_I_18_M
0.258
0.322 0.339 0.322 0.339
0.562
0.569 0.602 0.569 0.602
0.637
0.653 0.692 0.653 0.692
ns
HSTL_I_18_S
0.258
0.322 0.339 0.322 0.339
0.781
0.781 0.833 0.781 0.833
0.816
0.816 0.871 0.816 0.871
ns
HSTL_I_DCI_12_F
0.322
0.378 0.399 0.378 0.399
0.393
0.406 0.429 0.406 0.429
0.502
0.534 0.564 0.534 0.564
ns
HSTL_I_DCI_12_M
0.322
0.378 0.399 0.378 0.399
0.551
0.556 0.586 0.556 0.586
0.644
0.654 0.694 0.654 0.694
ns
HSTL_I_DCI_12_S
0.322
0.378 0.399 0.378 0.399
0.754
0.754 0.803 0.754 0.803
0.842
0.842 0.907 0.842 0.907
ns
HSTL_I_DCI_18_F
0.258
0.321 0.339 0.321 0.339
0.422
0.445 0.461 0.445 0.461
0.509
0.566 0.595 0.566 0.595
ns
HSTL_I_DCI_18_M
0.258
0.321 0.339 0.321 0.339
0.551
0.554 0.585 0.554 0.585
0.634
0.643 0.684 0.643 0.684
ns
HSTL_I_DCI_18_S
0.258
0.321 0.339 0.321 0.339
0.761
0.761 0.817 0.761 0.817
0.836
0.836 0.900 0.836 0.900
ns
HSTL_I_DCI_F
0.288
0.393 0.415 0.393 0.415
0.407
0.431 0.445 0.431 0.445
0.517
0.555 0.575 0.555 0.575
ns
HSTL_I_DCI_M
0.288
0.393 0.415 0.393 0.415
0.548
0.552 0.581 0.552 0.581
0.635
0.644 0.684 0.644 0.684
ns
HSTL_I_DCI_S
0.288
0.393 0.415 0.393 0.415
0.766
0.766 0.821 0.766 0.821
0.847
0.847 0.912 0.847 0.912
ns
HSTL_I_F
0.322
0.378 0.399 0.378 0.399
0.409
0.423 0.443 0.423 0.443
0.514
0.549 0.581 0.549 0.581
ns
HSTL_I_M
0.322
0.378 0.399 0.378 0.399
0.548
0.554 0.585 0.554 0.585
0.624
0.640 0.677 0.640 0.677
ns
HSTL_I_S
0.322
0.378 0.399 0.378 0.399
0.766
0.766 0.816 0.766 0.816
0.811
0.811 0.866 0.811 0.866
ns
HSUL_12_DCI_F
0.319
0.378 0.399 0.378 0.399
0.411
0.425 0.443 0.425 0.443
0.520
0.558 0.586 0.558 0.586
ns
HSUL_12_DCI_M
0.319
0.378 0.399 0.378 0.399
0.551
0.556 0.586 0.556 0.586
0.644
0.654 0.694 0.654 0.694
ns
HSUL_12_DCI_S
0.319
0.378 0.399 0.378 0.399
0.736
0.736 0.784 0.736 0.784
0.821
0.821 0.886 0.821 0.886
ns
HSUL_12_F
0.305
0.378 0.399 0.378 0.399
0.394
0.412 0.430 0.412 0.430
0.494
0.538 0.566 0.538 0.566
ns
HSUL_12_M
0.305
0.378 0.399 0.378 0.399
0.551
0.551 0.582 0.551 0.582
0.632
0.642 0.679 0.642 0.679
ns
HSUL_12_S
0.305
0.378 0.399 0.378 0.399
0.750
0.750 0.799 0.750 0.799
0.813
0.813 0.868 0.813 0.868
ns
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
26
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 29: IOB High Performance (HP) Switching Characteristics (cont'd)
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_O_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
0.72V
-2
Units
-1
LVCMOS12_F_2
0.443
0.512 0.555 0.512 0.555
0.657
0.672 0.692 0.672 0.692
0.862
0.898 0.922 0.898 0.922
ns
LVCMOS12_F_4
0.443
0.512 0.555 0.512 0.555
0.486
0.504 0.521 0.504 0.521
0.645
0.664 0.693 0.664 0.693
ns
LVCMOS12_F_6
0.443
0.512 0.555 0.512 0.555
0.469
0.485 0.507 0.485 0.507
0.585
0.634 0.669 0.634 0.669
ns
LVCMOS12_F_8
0.443
0.512 0.555 0.512 0.555
0.457
0.465 0.489 0.465 0.489
0.592
0.611 0.666 0.611 0.666
ns
LVCMOS12_M_2
0.443
0.512 0.555 0.512 0.555
0.687
0.708 0.727 0.708 0.727
0.889
0.916 0.945 0.916 0.945
ns
LVCMOS12_M_4
0.443
0.512 0.555 0.512 0.555
0.533
0.550 0.573 0.550 0.573
0.629
0.664 0.690 0.664 0.690
ns
LVCMOS12_M_6
0.443
0.512 0.555 0.512 0.555
0.520
0.527 0.554 0.527 0.554
0.608
0.622 0.652 0.622 0.652
ns
LVCMOS12_M_8
0.443
0.512 0.555 0.512 0.555
0.532
0.540 0.571 0.540 0.571
0.606
0.614 0.649 0.614 0.649
ns
LVCMOS12_S_2
0.443
0.512 0.555 0.512 0.555
0.767
0.767 0.803 0.767 0.803
0.981
0.990 1.024 0.990 1.024
ns
LVCMOS12_S_4
0.443
0.512 0.555 0.512 0.555
0.666
0.666 0.704 0.666 0.704
0.803
0.803 0.848 0.803 0.848
ns
LVCMOS12_S_6
0.443
0.512 0.555 0.512 0.555
0.657
0.657 0.695 0.657 0.695
0.732
0.732 0.774 0.732 0.774
ns
LVCMOS12_S_8
0.443
0.512 0.555 0.512 0.555
0.708
0.708 0.761 0.708 0.761
0.745
0.745 0.790 0.745 0.790
ns
LVCMOS15_F_12
0.368
0.414 0.445 0.414 0.445
0.485
0.500 0.522 0.500 0.522
0.584
0.647 0.682 0.647 0.682
ns
LVCMOS15_F_2
0.368
0.414 0.445 0.414 0.445
0.686
0.702 0.722 0.702 0.722
0.893
0.919 0.940 0.919 0.940
ns
LVCMOS15_F_4
0.368
0.414 0.445 0.414 0.445
0.567
0.579 0.601 0.579 0.601
0.727
0.755 0.781 0.755 0.781
ns
LVCMOS15_F_6
0.368
0.414 0.445 0.414 0.445
0.533
0.547 0.569 0.547 0.569
0.684
0.711 0.742 0.711 0.742
ns
LVCMOS15_F_8
0.368
0.414 0.445 0.414 0.445
0.500
0.518 0.538 0.518 0.538
0.635
0.686 0.703 0.686 0.703
ns
LVCMOS15_M_12
0.368
0.414 0.445 0.414 0.445
0.607
0.607 0.644 0.607 0.644
0.637
0.637 0.676 0.637 0.676
ns
LVCMOS15_M_2
0.368
0.414 0.445 0.414 0.445
0.736
0.741 0.770 0.741 0.770
0.929
0.938 0.962 0.938 0.962
ns
LVCMOS15_M_4
0.368
0.414 0.445 0.414 0.445
0.610
0.625 0.651 0.625 0.651
0.733
0.754 0.786 0.754 0.786
ns
LVCMOS15_M_6
0.368
0.414 0.445 0.414 0.445
0.564
0.576 0.604 0.576 0.604
0.655
0.674 0.710 0.674 0.710
ns
LVCMOS15_M_8
0.368
0.414 0.445 0.414 0.445
0.565
0.568 0.601 0.568 0.601
0.634
0.639 0.681 0.639 0.681
ns
LVCMOS15_S_12
0.368
0.414 0.445 0.414 0.445
0.788
0.788 0.855 0.788 0.855
0.695
0.695 0.733 0.695 0.733
ns
LVCMOS15_S_2
0.368
0.414 0.445 0.414 0.445
0.829
0.829 0.864 0.829 0.864
1.038
1.039 1.079 1.039 1.079
ns
LVCMOS15_S_4
0.368
0.414 0.445 0.414 0.445
0.687
0.687 0.725 0.687 0.725
0.813
0.813 0.851 0.813 0.851
ns
LVCMOS15_S_6
0.368
0.414 0.445 0.414 0.445
0.671
0.671 0.710 0.671 0.710
0.726
0.726 0.763 0.726 0.763
ns
LVCMOS15_S_8
0.368
0.414 0.445 0.414 0.445
0.704
0.704 0.755 0.704 0.755
0.721
0.721 0.758 0.721 0.758
ns
LVCMOS18_F_12
0.352
0.418 0.445 0.418 0.445
0.564
0.573 0.601 0.573 0.601
0.696
0.731 0.769 0.731 0.769
ns
LVCMOS18_F_2
0.352
0.418 0.445 0.418 0.445
0.723
0.739 0.760 0.739 0.760
0.918
0.945 0.971 0.945 0.971
ns
LVCMOS18_F_4
0.352
0.418 0.445 0.418 0.445
0.598
0.609 0.630 0.609 0.630
0.749
0.778 0.802 0.778 0.802
ns
LVCMOS18_F_6
0.352
0.418 0.445 0.418 0.445
0.598
0.603 0.633 0.603 0.633
0.781
0.781 0.808 0.781 0.808
ns
LVCMOS18_F_8
0.352
0.418 0.445 0.418 0.445
0.567
0.573 0.600 0.573 0.600
0.712
0.733 0.767 0.733 0.767
ns
LVCMOS18_M_12
0.352
0.418 0.445 0.418 0.445
0.640
0.640 0.678 0.640 0.678
0.670
0.670 0.709 0.670 0.709
ns
LVCMOS18_M_2
0.352
0.418 0.445 0.418 0.445
0.785
0.798 0.822 0.798 0.822
0.986
0.991 1.016 0.991 1.016
ns
LVCMOS18_M_4
0.352
0.418 0.445 0.418 0.445
0.658
0.664 0.693 0.664 0.693
0.786
0.798 0.836 0.798 0.836
ns
LVCMOS18_M_6
0.352
0.418 0.445 0.418 0.445
0.625
0.629 0.663 0.629 0.663
0.727
0.735 0.775 0.735 0.775
ns
LVCMOS18_M_8
0.352
0.418 0.445 0.418 0.445
0.626
0.626 0.661 0.626 0.661
0.705
0.705 0.746 0.705 0.746
ns
LVCMOS18_S_12
0.352
0.418 0.445 0.418 0.445
0.795
0.795 0.861 0.795 0.861
0.683
0.683 0.721 0.683 0.721
ns
LVCMOS18_S_2
0.352
0.418 0.445 0.418 0.445
0.861
0.862 0.897 0.862 0.897
1.061
1.076 1.098 1.076 1.098
ns
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
27
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 29: IOB High Performance (HP) Switching Characteristics (cont'd)
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_O_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
-1
0.90V
-3
0.85V
-2
-1
0.72V
-2
Units
-1
LVCMOS18_S_4
0.352
0.418 0.445 0.418 0.445
0.716
0.716 0.758 0.716 0.758
0.829
0.829 0.872 0.829 0.872
ns
LVCMOS18_S_6
0.352
0.418 0.445 0.418 0.445
0.682
0.682 0.724 0.682 0.724
0.724
0.724 0.762 0.724 0.762
ns
LVCMOS18_S_8
0.352
0.418 0.445 0.418 0.445
0.707
0.707 0.760 0.707 0.760
0.709
0.709 0.745 0.709 0.745
ns
LVDCI_15_F
0.369
0.425 0.462 0.425 0.462
0.407
0.426 0.443 0.426 0.443
0.514
0.548 0.581 0.548 0.581
ns
LVDCI_15_M
0.369
0.425 0.462 0.425 0.462
0.549
0.553 0.582 0.553 0.582
0.632
0.645 0.685 0.645 0.685
ns
LVDCI_15_S
0.369
0.425 0.462 0.425 0.462
0.749
0.749 0.803 0.749 0.803
0.821
0.821 0.890 0.821 0.890
ns
LVDCI_18_F
0.367
0.414 0.447 0.414 0.447
0.422
0.441 0.459 0.441 0.459
0.541
0.560 0.589 0.560 0.589
ns
LVDCI_18_M
0.367
0.414 0.447 0.414 0.447
0.546
0.554 0.585 0.554 0.585
0.622
0.644 0.683 0.644 0.683
ns
LVDCI_18_S
0.367
0.414 0.447 0.414 0.447
0.760
0.760 0.818 0.760 0.818
0.837
0.837 0.899 0.837 0.899
ns
LVDS
0.508
0.539 0.620 0.539 0.620
0.626
0.626 0.662 0.626 0.662
MIPI_DPHY_DCI_HS
0.305
0.386 0.415 0.386 0.415
0.489
0.502 0.522 0.502 0.522
N/A
N/A
N/A
N/A
N/A
ns
MIPI_DPHY_DCI_LP
8.438
8.438 8.792 8.438 8.792
0.895
0.914 0.937 0.914 0.937
N/A
N/A
N/A
N/A
N/A
ns
POD10_DCI_F
0.336
0.408 0.430 0.408 0.430
0.407
0.425 0.444 0.425 0.444
0.512
0.555 0.584 0.555 0.584
ns
POD10_DCI_M
0.336
0.408 0.430 0.408 0.430
0.533
0.542 0.571 0.542 0.571
0.618
0.640 0.681 0.640 0.681
ns
POD10_DCI_S
0.336
0.408 0.430 0.408 0.430
0.724
0.754 0.815 0.754 0.815
0.815
0.850 0.917 0.850 0.917
ns
960.447
ns
POD10_F
0.336
0.407 0.430 0.407 0.430
0.425
0.438 0.459 0.438 0.459
0.531
0.569 0.601 0.569 0.601
ns
POD10_M
0.336
0.407 0.430 0.407 0.430
0.519
0.538 0.568 0.538 0.568
0.589
0.630 0.667 0.630 0.667
ns
POD10_S
0.336
0.407 0.430 0.407 0.430
0.752
0.766 0.821 0.766 0.821
0.821
0.836 0.894 0.836 0.894
ns
POD12_DCI_F
0.336
0.409 0.431 0.409 0.431
0.411
0.425 0.443 0.425 0.443
0.519
0.558 0.586 0.558 0.586
ns
POD12_DCI_M
0.336
0.409 0.431 0.409 0.431
0.516
0.543 0.572 0.543 0.572
0.602
0.638 0.678 0.638 0.678
ns
POD12_DCI_S
0.336
0.409 0.431 0.409 0.431
0.740
0.772 0.822 0.772 0.822
0.833
0.862 0.929 0.862 0.929
ns
POD12_F
0.336
0.409 0.431 0.409 0.431
0.438
0.455 0.476 0.455 0.476
0.549
0.595 0.626 0.595 0.626
ns
POD12_M
0.336
0.409 0.431 0.409 0.431
0.551
0.551 0.582 0.551 0.582
0.632
0.641 0.679 0.641 0.679
ns
POD12_S
0.336
0.409 0.431 0.409 0.431
0.749
0.767 0.817 0.767 0.817
0.818
0.832 0.889 0.832 0.889
ns
SLVS_400_18
0.492
0.539 0.620 0.539 0.620
N/A
SSTL12_DCI_F
0.331
0.381 0.399 0.381 0.399
0.411
0.425 0.443 0.425 0.443
0.520
0.558 0.586 0.558 0.586
ns
SSTL12_DCI_M
0.331
0.381 0.399 0.381 0.399
0.549
0.557 0.587 0.557 0.587
0.643
0.654 0.694 0.654 0.694
ns
SSTL12_DCI_S
0.331
0.381 0.399 0.381 0.399
0.754
0.754 0.803 0.754 0.803
0.842
0.842 0.908 0.842 0.908
ns
SSTL12_F
0.320
0.403 0.403 0.403 0.403
0.394
0.412 0.430 0.412 0.430
0.494
0.538 0.566 0.538 0.566
ns
SSTL12_M
0.320
0.403 0.403 0.403 0.403
0.550
0.553 0.584 0.553 0.584
0.630
0.641 0.676 0.641 0.676
ns
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
ns
SSTL12_S
0.320
0.403 0.403 0.403 0.403
0.758
0.758 0.808 0.758 0.808
0.823
0.823 0.879 0.823 0.879
ns
SSTL135_DCI_F
0.341
0.366 0.399 0.366 0.399
0.392
0.411 0.428 0.411 0.428
0.494
0.537 0.565 0.537 0.565
ns
SSTL135_DCI_M
0.341
0.366 0.399 0.366 0.399
0.551
0.551 0.582 0.551 0.582
0.643
0.645 0.685 0.645 0.685
ns
SSTL135_DCI_S
0.341
0.366 0.399 0.366 0.399
0.746
0.746 0.799 0.746 0.799
0.829
0.829 0.893 0.829 0.893
ns
SSTL135_F
0.321
0.378 0.399 0.378 0.399
0.393
0.408 0.428 0.408 0.428
0.491
0.528 0.561 0.528 0.561
ns
SSTL135_M
0.321
0.378 0.399 0.378 0.399
0.548
0.555 0.585 0.555 0.585
0.621
0.641 0.679 0.641 0.679
ns
SSTL135_S
0.321
0.378 0.399 0.378 0.399
0.772
0.772 0.823 0.772 0.823
0.827
0.827 0.878 0.827 0.878
ns
SSTL15_DCI_F
0.319
0.402 0.417 0.402 0.417
0.394
0.412 0.429 0.412 0.429
0.497
0.531 0.563 0.531 0.563
ns
SSTL15_DCI_M
0.319
0.402 0.417 0.402 0.417
0.549
0.553 0.583 0.553 0.583
0.632
0.645 0.685 0.645 0.685
ns
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
28
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 29: IOB High Performance (HP) Switching Characteristics (cont'd)
TINBUF_DELAY_PAD_I
I/O Standards
0.90V
-3
0.85V
-2
TOUTBUF_DELAY_O_PAD
0.72V
-1
-2
-1
0.90V
0.85V
-3
-2
-1
TOUTBUF_DELAY_TD_PAD
0.72V
-2
0.90V
-1
-3
0.85V
-2
0.72V
-1
-2
Units
-1
SSTL15_DCI_S
0.319
0.402 0.417 0.402 0.417
0.768
0.768 0.822 0.768 0.822
0.847
0.847 0.912 0.847 0.912
ns
SSTL15_F
0.320
0.371 0.400 0.371 0.400
0.393
0.408 0.428 0.408 0.428
0.494
0.530 0.556 0.530 0.556
ns
SSTL15_M
0.320
0.371 0.400 0.371 0.400
0.547
0.554 0.585 0.554 0.585
0.624
0.639 0.677 0.639 0.677
ns
SSTL15_S
0.320
0.371 0.400 0.371 0.400
0.767
0.767 0.817 0.767 0.817
0.813
0.813 0.867 0.813 0.867
ns
SSTL18_I_DCI_F
0.256
0.329 0.336 0.329 0.336
0.422
0.445 0.461 0.445 0.461
0.540
0.566 0.595 0.566 0.595
ns
SSTL18_I_DCI_M
0.256
0.329 0.336 0.329 0.336
0.552
0.554 0.585 0.554 0.585
0.629
0.644 0.683 0.644 0.683
ns
SSTL18_I_DCI_S
0.256
0.329 0.336 0.329 0.336
0.762
0.762 0.818 0.762 0.818
0.837
0.837 0.899 0.837 0.899
ns
SSTL18_I_F
0.259
0.316 0.337 0.316 0.337
0.439
0.454 0.476 0.454 0.476
0.549
0.578 0.608 0.578 0.608
ns
SSTL18_I_M
0.259
0.316 0.337 0.316 0.337
0.567
0.571 0.603 0.571 0.603
0.535
0.652 0.692 0.652 0.692
ns
SSTL18_I_S
0.259
0.316 0.337 0.316 0.337
0.782
0.782 0.835 0.782 0.835
0.816
0.816 0.870 0.816 0.870
ns
SUB_LVDS
0.508
0.539 0.620 0.539 0.620
0.658
0.660 0.692 0.660 0.692
907.4
969.863
ns
IOB 3-state Output Switching Characteristics
Table 30 specifies the values of TOUTBUF_DELAY_TE_PAD and TINBUF_DELAY_IBUFDIS_O.
• TOUTBUF_DELAY_TE_PAD is the delay from the T pin to the IOB pad through the output buffer of an IOB pad,
when 3-state is enabled (i.e., a high impedance state).
• TINBUF_DELAY_IBUFDIS_O is the IOB delay from IBUFDISABLE to O output.
• In HP I/O banks, the internal DCI termination turn-off time is always faster than TOUTBUF_DELAY_TE_PAD when
the DCITERMDISABLE pin is used.
• In HD I/O banks, the internal IN_TERM termination turn-off time is always faster than TOUTBUF_DELAY_TE_PAD
when the INTERMDISABLE pin is used.
Table 30: IOB 3-state Output Switching Characteristics
Speed Grade and VCCINT Operating Voltages
Symbol
TOUTBUF_DELAY_TE_PAD
TINBUF_DELAY_IBUFDIS_O
Description
0.90V
0.85V
Units
0.72V
-3
-2
-1
-2
-1
T input to pad high-impedance for HD I/O
banks
6.167
6.318
6.369
6.699
6.752
ns
T input to pad high-impedance for HP I/O
banks
5.330
5.330
5.341
5.330
5.341
ns
IBUF turn-on time from IBUFDISABLE to O
output for HD I/O banks
2.266
2.266
2.430
2.266
2.430
ns
IBUF turn-on time from IBUFDISABLE to O
output for HP I/O banks
0.873
0.936
1.037
0.936
1.037
ns
Input Delay Measurement Methodology
The following table shows the test setup parameters used for measuring input delay.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
29
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 31: Input Delay Measurement Methodology
Description
I/O Standard
Attribute
VL1, 2
VH1, 2
VMEAS 1, 4 VREF 1, 3, 5
LVCMOS, 1.2V
LVCMOS12
0.1
1.1
0.6
–
LVCMOS, LVDCI, HSLVDCI, 1.5V
LVCMOS15, LVDCI_15,
HSLVDCI_15
0.1
1.4
0.75
–
LVCMOS, LVDCI, HSLVDCI, 1.8V
LVCMOS18, LVDCI_18,
HSLVDCI_18
0.1
1.7
0.9
–
LVCMOS, 2.5V
LVCMOS25
0.1
2.4
1.25
–
LVCMOS, 3.3V
LVCMOS33
0.1
3.2
1.65
–
LVTTL, 3.3V
LVTTL
0.1
3.2
1.65
–
HSTL (high-speed transceiver logic), class I, 1.2V
HSTL_I_12
VREF – 0.25
VREF + 0.25
VREF
0.6
HSTL, class I, 1.5V
HSTL_I
VREF – 0.325
VREF + 0.325
VREF
0.75
HSTL, class I, 1.8V
HSTL_I_18
VREF – 0.4
VREF + 0.4
VREF
0.9
HSUL (high-speed unterminated logic), 1.2V
HSUL_12
VREF – 0.25
VREF + 0.25
VREF
0.6
SSTL12 (stub series terminated logic), 1.2V
SSTL12
VREF – 0.25
VREF + 0.25
VREF
0.6
SSTL135 and SSTL135 class II, 1.35V
SSTL135, SSTL135_II
VREF – 0.2875
VREF + 0.2875
VREF
0.675
SSTL15 and SSTL15 class II, 1.5V
SSTL15, SSTL15_II
VREF – 0.325
VREF + 0.325
VREF
0.75
SSTL18, class I and II, 1.8V
SSTL18_I, SSTL18_II
VREF – 0.4
VREF + 0.4
VREF
0.9
POD10, 1.0V
POD10
VREF – 0.2
VREF + 0.2
VREF
0.7
POD12, 1.2V
POD12
VREF – 0.24
VREF + 0.24
VREF
0.84
DIFF_HSTL, class I, 1.2V
DIFF_HSTL_I_12
0.6 – 0.25
0.6 + 0.25
06
–
0.75 + 0.325
06
–
0.9 + 0.4
06
–
0.6 + 0.25
06
–
–
DIFF_HSTL, class I, 1.5V
DIFF_HSTL, class I, 1.8V
DIFF_HSUL, 1.2V
DIFF_HSTL_I
DIFF_HSTL_I_18
DIFF_HSUL_12
0.75 – 0.325
0.9 – 0.4
0.6 – 0.25
DIFF_SSTL, 1.2V
DIFF_SSTL12
0.6 – 0.25
0.6 + 0.25
06
DIFF_SSTL135 and DIFF_SSTL135 class II, 1.35V
DIFF_SSTL135,
DIFF_SSTL135_II
0.675 – 0.2875
0.675 + 0.2875
06
–
DIFF_SSTL15 and DIFF_SSTL15 class II, 1.5V
DIFF_SSTL15,
DIFF_SSTL15_II
0.75 – 0.325
0.75 + 0.325
06
–
DIFF_SSTL18_I, DIFF_SSTL18_II, 1.8V
DIFF_SSTL18_I,
DIFF_SSTL18_II
0.9 – 0.4
0.9 + 0.4
06
–
DIFF_POD10, 1.0V
DIFF_POD10
0.5 – 0.2
0.5 + 0.2
06
–
DIFF_POD12, 1.2V
DIFF_POD12
0.6 – 0.25
0.6 + 0.25
06
–
LVDS (low-voltage differential signaling), 1.8V
LVDS
0.9 – 0.125
0.9 + 0.125
06
–
1.25 + 0.125
06
–
0.9 + 0.125
06
–
–
LVDS_25, 2.5V
SUB_LVDS, 1.8V
LVDS_25
SUB_LVDS
1.25 – 0.125
0.9 – 0.125
SLVS, 1.8V
SLVS_400_18
0.9 – 0.125
0.9 + 0.125
06
SLVS, 2.5V
SLVS_400_25
1.25 – 0.125
1.25 + 0.125
06
–
LVPECL, 2.5V
LVPECL
1.25 – 0.125
1.25 + 0.125
06
–
0.2 + 0.125
06
–
MIPI D-PHY (high speed) 1.2V
DS922 (v1.17) February 16, 2021
Product Specification
MIPI_DPHY_DCI_HS
0.2 – 0.125
Send Feedback
www.xilinx.com
30
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 31: Input Delay Measurement Methodology (cont'd)
I/O Standard
Attribute
Description
MIPI D-PHY (low power) 1.2V
MIPI_DPHY_DCI_LP
VL1, 2
VH1, 2
0.715 – 0.2
0.715 + 0.2
VMEAS 1, 4 VREF 1, 3, 5
06
–
Notes:
1.
The input delay measurement methodology parameters for LVDCI/HSLVDCI are the same for LVCMOS standards of the same voltage.
Parameters for all other DCI standards are the same for the corresponding non-DCI standards.
2.
Input waveform switches between VL and VH.
3.
Measurements are made at typical, minimum, and maximum VREF values. Reported delays reflect worst case of these measurements.
VREF values listed are typical.
4.
Input voltage level from which measurement starts.
5.
This is an input voltage reference that bears no relation to the VREF/VMEAS parameters found in IBIS models and/or noted in Figure 1.
6.
The value given is the differential input voltage.
Output Delay Measurement Methodology
Output delays are measured with short output traces. Standard termination was used for all testing. The
propagation delay of the trace is characterized separately and subtracted from the final measurement, and is
therefore not included in the generalized test setups shown in Figure 1 and Figure 2.
Figure 1: Single-Ended Test Setup
VREF
RREF
Output
VMEAS (voltage level when taking delay measurement)
CREF (probe capacitance)
X16654-072117
Figure 2: Differential Test Setup
Output
+
CREF
RREF
VMEAS
–
X16640-072117
Parameters VREF, RREF, CREF, and VMEAS fully describe the test conditions for each I/O standard. The most
accurate prediction of propagation delay in any given application can be obtained through IBIS simulation, using
this method:
1. Simulate the output driver of choice into the generalized test setup using values from Table 32.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
31
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
2. Record the time to VMEAS.
3. Simulate the output driver of choice into the actual PCB trace and load using the appropriate IBIS model or
capacitance value to represent the load.
4. Record the time to VMEAS.
5. Compare the results of step 2 and step 4. The increase or decrease in delay yields the actual propagation
delay of the PCB trace.
Table 32: Output Delay Measurement Methodology
Description
I/O Standard Attribute
RREF
(Ω)
CREF1
(pF)
VMEAS
(V)
VREF
(V)
LVCMOS, 1.2V
LVCMOS12
1M
0
0.6
0
LVCMOS, 1.5V
LVCMOS15
1M
0
0.75
0
LVCMOS, 1.8V
LVCMOS18
1M
0
0.9
0
LVCMOS, 2.5V
LVCMOS25
1M
0
1.25
0
LVCMOS, 3.3V
LVCMOS33
1M
0
1.65
0
LVTTL, 3.3V
LVTTL
1M
0
1.65
0
LVDCI, HSLVDCI, 1.5V
LVDCI_15, HSLVDCI_15
50
0
VREF
0.75
LVDCI, HSLVDCI, 1.8V
LVDCI_15, HSLVDCI_18
50
0
VREF
0.9
HSTL (high-speed transceiver logic), class I, 1.2V
HSTL_I_12
50
0
VREF
0.6
HSTL, class I, 1.5V
HSTL_I
50
0
VREF
0.75
HSTL, class I, 1.8V
HSTL_I_18
50
0
VREF
0.9
HSUL (high-speed unterminated logic), 1.2V
HSUL_12
50
0
VREF
0.6
SSTL12 (stub series terminated logic), 1.2V
SSTL12
50
0
VREF
0.6
SSTL135 and SSTL135 class II, 1.35V
SSTL135, SSTL135_II
50
0
VREF
0.675
SSTL15 and SSTL15 class II, 1.5V
SSTL15, SSTL15_II
50
0
VREF
0.75
SSTL18, class I and class II, 1.8V
SSTL18_I, SSTL18_II
50
0
VREF
0.9
POD10, 1.0V
POD10
50
0
VREF
1.0
POD12, 1.2V
POD12
50
0
VREF
1.2
DIFF_HSTL, class I, 1.2V
DIFF_HSTL_I_12
50
0
VREF
0.6
DIFF_HSTL, class I, 1.5V
DIFF_HSTL_I
50
0
VREF
0.75
DIFF_HSTL, class I, 1.8V
DIFF_HSTL_I_18
50
0
VREF
0.9
DIFF_HSUL, 1.2V
DIFF_HSUL_12
50
0
VREF
0.6
DIFF_SSTL12, 1.2V
DIFF_SSTL12
50
0
VREF
0.6
DIFF_SSTL135 and DIFF_SSTL135 class II, 1.35V
DIFF_SSTL135, DIFF_SSTL135_II
50
0
VREF
0.675
DIFF_SSTL15 and DIFF_SSTL15 class II, 1.5V
DIFF_SSTL15, DIFF_SSTL15_II
50
0
VREF
0.75
DIFF_SSTL18, class I and II, 1.8V
DIFF_SSTL18_I, DIFF_SSTL18_II
50
0
VREF
0.9
DIFF_POD10, 1.0V
DIFF_POD10
50
0
VREF
1.0
DIFF_POD12, 1.2V
DIFF_POD12
50
0
VREF
1.2
LVDS (low-voltage differential signaling), 1.8V
LVDS
100
0
02
0
SUB_LVDS, 1.8V
SUB_LVDS
100
0
02
0
0
02
0
MIPI D-PHY (high speed) 1.2V
DS922 (v1.17) February 16, 2021
Product Specification
MIPI_DPHY_DCI_HS
100
Send Feedback
www.xilinx.com
32
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 32: Output Delay Measurement Methodology (cont'd)
Description
MIPI D-PHY (low power) 1.2V
I/O Standard Attribute
RREF
(Ω)
CREF1
(pF)
VMEAS
(V)
VREF
(V)
1M
0
0.6
0
MIPI_DPHY_DCI_LP
Notes:
1.
CREF is the capacitance of the probe, nominally 0 pF.
2.
The value given is the differential output voltage.
Block RAM and FIFO Switching Characteristics
Table 33: Block RAM and FIFO Switching Characteristics
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
Maximum Frequency
FMAX_WF_NC
Block RAM (WRITE_FIRST and NO_CHANGE modes)
825
738
645
585
516
MHz
FMAX_RF
Block RAM (READ_FIRST mode)
718
637
575
510
460
MHz
FMAX_FIFO
FIFO in all modes without ECC
825
738
645
585
516
MHz
FMAX_ECC
Block RAM and FIFO in ECC configuration without
PIPELINE
718
637
575
510
460
MHz
Block RAM and FIFO in ECC configuration with
PIPELINE and Block RAM in WRITE_FIRST or
NO_CHANGE mode
825
738
645
585
516
MHz
Minimum pulse width
495
542
543
577
578
ps
TPW1
Block RAM and FIFO Clock-to-Out Delays
TRCKO_DO
Clock CLK to DOUT output (without output register)
0.91
1.02
1.11
1.46
1.53
ns, Max
TRCKO_DO_REG
Clock CLK to DOUT output (with output register)
0.27
0.29
0.30
0.42
0.44
ns, Max
Notes:
1.
The MMCM and PLL DUTY_CYCLE attribute should be set to 50% to meet the pulse-width requirements at the higher frequencies.
UltraRAM Switching Characteristics
The UltraScale Architecture and Product Data Sheet: Overview (DS890) lists the Kintex UltraScale+ FPGAs that
include this memory.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
33
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 34: UltraRAM Switching Characteristics
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
Maximum Frequency
FMAX
UltraRAM maximum frequency with
OREG_B = True
650
600
575
500
481
MHz
FMAX_ECC_NOPIPELINE
UltraRAM maximum frequency with
OREG_B = False and EN_ECC_RD_B = True
435
400
386
312
303
MHz
FMAX_NOPIPELINE
UltraRAM maximum frequency with
OREG_B = False and EN_ECC_RD_B = False
528
500
478
404
389
MHz
TPW1
Minimum pulse width
650
700
730
800
832
ps
TRSTPW
Asynchronous reset minimum pulse width. One
cycle required
1 clock cycle
Notes:
1.
The MMCM and PLL DUTY_CYCLE attribute should be set to 50% to meet the pulse-width requirements at the higher frequencies.
Input/Output Delay Switching Characteristics
Table 35: Input/Output Delay Switching Characteristics
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
-3
FREFCLK
0.85V
-2
0.72V
-1
-2
Units
-1
Reference clock frequency for IDELAYCTRL
(component mode)
300 to 800
MHz
Reference clock frequency when using
BITSLICE_CONTROL with REFCLK (in native
mode (for RX_BITSLICE only))
300 to 800
MHz
Reference clock frequency for
BITSLICE_CONTROL with PLL_CLK (in native
mode)1
TMINPER_CLK
Minimum period for IODELAY clock
TMINPER_RST
Minimum reset pulse width
TIDELAY_RESOLUTION/
TODELAY_RESOLUTION
IDELAY/ODELAY chain resolution
300 to
2666.67
300 to
2666.67
3.195
3.195
300 to
2400
300 to
2400
300 to
2133
MHz
3.195
3.195
3.195
ns
52.00
ns
2.1 to 12
ps
Notes:
1.
PLL settings could restrict the minimum allowable data rate. For example, when using a PLL with CLKOUTPHY_MODE = VCO_HALF, the
minimum frequency is PLL_FVCOMIN/2.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
34
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
DSP48 Slice Switching Characteristics
Table 36: DSP48 Slice Switching Characteristics
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.72V1
0.85V
Units
-3
-2
-1
-2
-1
Maximum Frequency
FMAX
With all registers used
891
775
645
644
600
MHz
FMAX_PATDET
With pattern detector
794
687
571
562
524
MHz
FMAX_MULT_NOMREG
Two register multiply without MREG
635
544
456
440
413
MHz
FMAX_MULT_NOMREG_PATDET
Two register multiply without MREG
with pattern detect
577
492
410
395
371
MHz
FMAX_PREADD_NOADREG
Without ADREG
655
565
468
453
423
MHz
FMAX_NOPIPELINEREG
Without pipeline registers (MREG,
ADREG)
483
410
338
323
304
MHz
FMAX_NOPIPELINEREG_PATDET
Without pipeline registers (MREG,
ADREG) with pattern detect
448
379
314
299
280
MHz
Notes:
1.
For devices operating at the lower power VCCINT = 0.72V voltages, DSP cascades that cross the clock region center might operate below
the specified FMAX.
Clock Buffers and Networks
Table 37: Clock Buffers Switching Characteristics
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
891
775
667
725
667
MHz
891
775
667
725
667
MHz
891
775
667
725
667
MHz
891
775
667
725
667
MHz
512
512
512
MHz
Global Clock Switching Characteristics (Including BUFGCTRL)
FMAX
Maximum frequency of a global clock tree (BUFG)
Global Clock Buffer with Input Divide Capability (BUFGCE_DIV)
FMAX
Maximum frequency of a global clock buffer with input
divide capability (BUFGCE_DIV)
Global Clock Buffer with Clock Enable (BUFGCE)
FMAX
Maximum frequency of a global clock buffer with clock
enable (BUFGCE)
Leaf Clock Buffer with Clock Enable (BUFCE_LEAF)
FMAX
Maximum frequency of a leaf clock buffer with clock
enable (BUFCE_LEAF)
GTH or GTY Clock Buffer with Clock Enable and Clock Input Divide Capability (BUFG_GT)
FMAX
Maximum frequency of a serial transceiver clock buffer
with clock enable and clock input divide capability
DS922 (v1.17) February 16, 2021
Product Specification
512
512
Send Feedback
www.xilinx.com
35
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
MMCM Switching Characteristics
Table 38: MMCM Specification
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
MMCM_FINMAX
Maximum input clock frequency
1066
933
800
933
800
MHz
MMCM_FINMIN
Minimum input clock frequency
10
10
10
10
10
MHz
MMCM_FINJITTER
Maximum input clock period jitter
MMCM_FINDUTY
Input duty cycle range: 10–49 MHz
25–75
%
Input duty cycle range: 50–199 MHz
30–70
%
Input duty cycle range: 200–399 MHz
35–65
%
Input duty cycle range: 400–499 MHz
40–60
%
Input duty cycle range: >500 MHz
45–55
%
< 20% of clock input period or 1 ns Max
MMCM_FMIN_PSCLK
Minimum dynamic phase shift clock frequency
0.01
0.01
0.01
0.01
0.01
MHz
MMCM_FMAX_PSCLK
Maximum dynamic phase shift clock
frequency
550
500
450
500
450
MHz
MMCM_FVCOMIN
Minimum MMCM VCO frequency
800
800
800
800
800
MHz
MMCM_FVCOMAX
Maximum MMCM VCO frequency
1600
1600
1600
1600
1600
MHz
typical1
MMCM_FBANDWIDTH
Low MMCM bandwidth at
1.00
1.00
1.00
1.00
1.00
MHz
High MMCM bandwidth at typical1
4.00
4.00
4.00
4.00
4.00
MHz
MMCM_TSTATPHAOFFSET
Static phase offset of the MMCM outputs2
0.12
0.12
0.12
0.12
0.12
ns
MMCM_TOUTJITTER
MMCM output jitter.
MMCM_TOUTDUTY
MMCM output clock duty cycle
MMCM_TLOCKMAX
MMCM maximum lock time for
MMCM_FPFDMIN
Note 3
precision4
0.165
0.20
0.20
0.20
0.20
ns
100
100
100
100
100
µs
MMCM_FOUTMAX
MMCM maximum output frequency
891
775
667
725
667
MHz
MMCM_FOUTMIN
MMCM minimum output frequency4, 5
6.25
6.25
6.25
6.25
6.25
MHz
MMCM_TEXTFDVAR
External clock feedback variation
MMCM_RSTMINPULSE
Minimum reset pulse width
5.00
5.00
5.00
5.00
5.00
ns
MMCM_FPFDMAX
Maximum frequency at the phase frequency
detector
550
500
450
500
450
MHz
MMCM_FPFDMIN
Minimum frequency at the phase frequency
detector
10
10
10
10
10
MHz
MMCM_TFBDELAY
Maximum delay in the feedback path
MMCM_FDPRCLK_MAX
Maximum DRP clock frequency
250
MHz
< 20% of clock input period or 1 ns Max
5 ns Max or one clock cycle
250
250
250
250
Notes:
1.
The MMCM does not filter typical spread-spectrum input clocks because they are usually far below the bandwidth filter frequencies.
2.
The static offset is measured between any MMCM outputs with identical phase.
3.
Values for this parameter are available in the Clocking Wizard.
4.
Includes global clock buffer.
5.
Calculated as FVCO/128 assuming output duty cycle is 50%.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
36
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
PLL Switching Characteristics
Table 39: PLL Specification
Speed Grade and VCCINT Operating Voltages
Description1
Symbol
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
PLL_FINMAX
Maximum input clock frequency
1066
933
800
933
800
MHz
PLL_FINMIN
Minimum input clock frequency
70
70
70
70
70
MHz
PLL_FINJITTER
Maximum input clock period jitter
PLL_FINDUTY
Input duty cycle range: 70–399 MHz
35–65
%
Input duty cycle range: 400–499 MHz
40–60
%
< 20% of clock input period or 1 ns Max
Input duty cycle range: >500 MHz
PLL_FVCOMIN
Minimum PLL VCO frequency
PLL_FVCOMAX
Maximum PLL VCO frequency
outputs2
45–55
%
750
750
750
750
750
MHz
1500
1500
1500
1500
1500
MHz
0.12
0.12
0.12
0.12
0.12
ns
0.20
0.20
ns
PLL_TSTATPHAOFFSET
Static phase offset of the PLL
PLL_TOUTJITTER
PLL output jitter.
PLL_TOUTDUTY
PLL CLKOUT0, CLKOUT0B, CLKOUT1, CLKOUT1B
duty-cycle precision4
PLL_TLOCKMAX
PLL maximum lock time
PLL_FOUTMAX
PLL maximum output frequency at CLKOUT0,
CLKOUT0B, CLKOUT1, CLKOUT1B
891
775
667
725
667
MHz
PLL maximum output frequency at CLKOUTPHY
2667
2667
2400
2400
2133
MHz
PLL_FOUTMIN
PLL minimum output frequency at CLKOUT0,
CLKOUT0B, CLKOUT1, CLKOUT1B5
5.86
5.86
5.86
5.86
5.86
MHz
PLL minimum output frequency at CLKOUTPHY
Note 3
0.165
0.20
0.20
100
µs
2 x VCO mode: 1500, 1 x VCO mode: 750, 0.5 x VCO mode:
375
MHz
PLL_RSTMINPULSE
Minimum reset pulse width
5.00
5.00
5.00
5.00
5.00
ns
PLL_FPFDMAX
Maximum frequency at the phase frequency
detector
667.5
667.5
667.5
667.5
667.5
MHz
PLL_FPFDMIN
Minimum frequency at the phase frequency
detector
70
70
70
70
70
MHz
PLL_FBANDWIDTH
PLL bandwidth at typical
14
14
14
14
14
MHz
PLL_FDPRCLK_MAX
Maximum DRP clock frequency
250
250
250
250
250
MHz
Notes:
1.
The PLL does not filter typical spread-spectrum input clocks because they are usually far below the loop filter frequencies.
2.
The static offset is measured between any PLL outputs with identical phase.
3.
Values for this parameter are available in the Clocking Wizard.
4.
Includes global clock buffer.
5.
Calculated as FVCO/128 assuming output duty cycle is 50%.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
37
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Device Pin-to-Pin Output Parameter Guidelines
The pin-to-pin numbers in the following tables are based on the clock root placement in the center of the
device. The actual pin-to-pin values will vary if the root placement selected is different. Consult the Vivado
Design Suite timing report for the actual pin-to-pin values.
Table 40: Global Clock Input to Output Delay Without MMCM (Near Clock Region)
Speed Grade and VCCINT Operating Voltages
Symbol
Description1
Device
0.90V
-3
0.85V
0.72V
-2
Units
-1
-2
-1
SSTL15 Global Clock Input to Output Delay using Output Flip-Flop, Fast Slew Rate, without MMCM
TICKOF
Global clock input and output flip-flop
without MMCM (near clock region)
XCKU3P
4.65
5.09
5.48
6.37
6.84
ns
XCKU5P
4.65
5.09
5.48
6.37
6.84
ns
XCKU9P
5.42
5.91
6.35
7.48
8.03
ns
XCKU11P
5.92
6.49
6.96
8.16
8.91
ns
XCKU13P
5.58
6.09
6.55
7.75
8.33
ns
XCKU15P
6.29
6.90
7.40
8.68
9.32
ns
XCKU19P
5.85
6.43
6.91
8.09
8.72
ns
XQKU5P
N/A
5.09
5.48
N/A
6.84
ns
XQKU15P
N/A
6.90
7.40
N/A
9.32
ns
Notes:
1.
This table lists representative values where one global clock input drives one vertical clock line in each accessible column, and where all
accessible I/O and CLB flip-flops are clocked by the global clock net.
Table 41: Global Clock Input to Output Delay Without MMCM (Far Clock Region)
Speed Grade and VCCINT Operating Voltages
Symbol
Description1
Device
0.90V
-3
0.85V
-2
0.72V
Units
-1
-2
-1
SSTL15 Global Clock Input to Output Delay using Output Flip-Flop, Fast Slew Rate, without MMCM
TICKOF_FAR
Global clock input and output flip-flop
without MMCM (far clock region)
XCKU3P
4.84
5.30
5.70
6.64
7.14
ns
XCKU5P
4.84
5.30
5.70
6.64
7.14
ns
XCKU9P
5.91
6.49
6.97
8.16
8.76
ns
XCKU11P
6.29
6.91
7.41
8.72
9.52
ns
XCKU13P
5.90
6.49
6.96
8.16
8.77
ns
XCKU15P
6.84
7.53
8.07
9.52
10.23
ns
XCKU19P
6.23
6.86
7.35
8.65
9.33
ns
XQKU5P
N/A
5.30
5.70
N/A
7.14
ns
XQKU15P
N/A
7.53
8.07
N/A
10.23
ns
Notes:
1.
This table lists representative values where one global clock input drives one vertical clock line in each accessible column, and where all
accessible I/O and CLB flip-flops are clocked by the global clock net.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
38
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 42: Global Clock Input to Output Delay With MMCM
Speed Grade and VCCINT Operating Voltages
Description1, 2
Symbol
Device
0.90V
-3
0.85V
-2
0.72V
Units
-1
-2
-1
SSTL15 Global Clock Input to Output Delay using Output Flip-Flop, Fast Slew Rate, with MMCM
TICKOFMMCMCC
Global clock input and output flip-flop with
MMCM
XCKU3P
1.67
1.98
2.17
2.59
2.74
ns
XCKU5P
1.67
1.98
2.17
2.59
2.74
ns
XCKU9P
1.83
2.15
2.36
2.80
2.95
ns
XCKU11P
1.96
2.30
2.51
2.99
3.20
ns
XCKU13P
1.85
2.18
2.38
2.82
2.98
ns
XCKU15P
2.08
2.44
2.66
3.15
3.33
ns
XCKU19P
1.82
2.18
2.39
2.86
3.04
ns
XQKU5P
N/A
1.98
2.17
N/A
2.74
ns
XQKU15P
N/A
2.44
2.66
N/A
3.33
ns
Notes:
1.
This table lists representative values where one global clock input drives one vertical clock line in each accessible column, and where all
accessible I/O and CLB flip-flops are clocked by the global clock net.
2.
MMCM output jitter is already included in the timing calculation.
Table 43: Source Synchronous Output Characteristics (Component Mode)
Speed Grade and VCCINT Operating Voltages
Description
0.90V
-3
TOUTPUT_LOGIC_DELAY_VARIATION
1
0.85V
-2
0.72V
-1
-2
Units
-1
80
ps
Notes:
1.
Delay mismatch across a transmit bus when using component mode output logic (ODDRE1, OSERDESE3) within a bank.
Device Pin-to-Pin Input Parameter Guidelines
The pin-to-pin numbers in the following tables are based on the clock root placement in the center of the
device. The actual pin-to-pin values will vary if the root placement selected is different. Consult the Vivado
Design Suite timing report for the actual pin-to-pin values.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
39
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 44: Global Clock Input Setup and Hold With 3.3V HD I/O Without MMCM
Symbol
Description
Device
Speed Grade and VCCINT Operating
Voltages
0.90V
-3
0.85V
-2
0.72V
-1
-2
-1
Units
Input Setup and Hold Time Relative to Global Clock Input Signal using SSTL15 Standard.1, 2, 3
TPSFD_KU3P
TPHFD_KU3P
Global clock input and input
flip-flop (or latch) without
MMCM
TPSFD_KU5P
Setup
XCKU3P
Hold
Setup
TPHFD_KU5P
Hold
TPSFD_KU9P
Setup
TPHFD_KU9P
Hold
TPSFD_KU11P
Setup
TPHFD_KU11P
Hold
TPSFD_KU13P
Setup
TPHFD_KU13P
Hold
TPSFD_KU15P
Setup
TPHFD_KU15P
Hold
TPSFD_KU19P
Setup
TPHFD_KU19P
Hold
TPSFD_XQKU5P
Setup
TPHFD_XQKU5P
Hold
TPSFD_XQKU15P
Setup
TPHFD_XQKU15P
Hold
XCKU5P
XCKU9P
XCKU11P
XCKU13P
XCKU15P
XCKU19P
XQKU5P
XQKU15P
1.98
2.28
2.38
3.55
3.83
ns
–0.36
–0.36
–0.36
–1.04
–1.04
ns
1.98
2.28
2.38
3.55
3.83
ns
–0.36
–0.36
–0.36
–1.04
–1.04
ns
1.51
1.79
1.86
2.85
3.06
ns
–0.05
–0.05
–0.05
–0.60
–0.60
ns
1.99
2.28
2.38
3.54
3.79
ns
–0.38
–0.38
–0.38
–1.05
–1.05
ns
1.51
1.79
1.85
2.84
3.05
ns
–0.04
–0.04
–0.04
–0.60
–0.60
ns
2.00
2.29
2.38
3.56
3.83
ns
–0.38
–0.38
–0.38
–1.08
–1.08
ns
0.88
1.03
1.04
1.99
2.13
ns
0.51
0.51
0.51
–0.03
–0.03
ns
N/A
2.28
2.38
N/A
3.83
ns
N/A
–0.36
–0.36
N/A
–1.04
ns
N/A
2.29
2.38
N/A
3.83
ns
N/A
–0.38
–0.38
N/A
–1.08
ns
Notes:
1.
Setup and hold times are measured over worst case conditions (process, voltage, temperature). Setup time is measured relative to the
global clock input signal using the slowest process, slowest temperature, and slowest voltage. Hold time is measured relative to the
global clock input signal using the fastest process, fastest temperature, and fastest voltage.
2.
This table lists representative values where one global clock input drives one vertical clock line in each accessible column, and where all
accessible I/O and CLB flip-flops are clocked by the global clock net.
3.
Use IBIS to determine any duty-cycle distortion incurred using various standards.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
40
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 45: Global Clock Input Setup and Hold With MMCM
Symbol
Description
Device
Speed Grade and VCCINT Operating
Voltages
0.90V
-3
0.85V
-2
0.72V
-1
-2
-1
Units
Input Setup and Hold Time Relative to Global Clock Input Signal using SSTL15 Standard.1, 2, 3
TPSMMCMCC_KU3P
TPHMMCMCC_KU3P
Global clock input and input
flip-flop (or latch) with MMCM
TPSMMCMCC_KU5P
Setup
XCKU3P
Hold
Setup
TPHMMCMCC_KU5P
Hold
TPSMMCMCC_KU9P
Setup
TPHMMCMCC_KU9P
Hold
TPSMMCMCC_KU11P
Setup
TPHMMCMCC_KU11P
Hold
TPSMMCMCC_KU13P
Setup
TPHMMCMCC_KU13P
Hold
TPSMMCMCC_KU15P
Setup
TPHMMCMCC_KU15P
Hold
TPSMMCMCC_KU19P
Setup
TPHMMCMCC_KU19P
Hold
TPSMMCMCC_XQKU5P
Setup
TPHMMCMCC_XQKU5P
Hold
TPSMMCMCC_XQKU15P
Setup
TPHMMCMCC_XQKU15
Hold
XCKU5P
XCKU9P
XCKU11P
XCKU13P
XCKU15P
XCKU19P
XQKU5P
XQKU15P
2.04
2.04
2.16
2.04
2.16
ns
–0.17
–0.17
–0.17
–0.23
–0.23
ns
2.04
2.04
2.16
2.04
2.16
ns
–0.17
–0.17
–0.17
–0.23
–0.23
ns
2.00
2.00
2.12
2.00
2.12
ns
–0.11
–0.11
–0.11
–0.18
–0.18
ns
1.89
1.89
2.02
1.89
2.02
ns
–0.20
–0.20
–0.20
–0.25
–0.25
ns
1.99
1.99
2.12
1.99
2.12
ns
–0.10
–0.10
–0.10
–0.16
–0.16
ns
1.89
1.89
2.03
1.89
2.03
ns
–0.16
–0.16
–0.16
–0.23
–0.23
ns
2.01
2.02
2.13
2.02
2.13
ns
–0.09
–0.09
–0.09
–0.18
–0.18
ns
N/A
2.04
2.16
N/A
2.16
ns
N/A
–0.17
–0.17
N/A
–0.23
ns
N/A
1.89
2.03
N/A
2.03
ns
N/A
–0.16
–0.16
N/A
–0.23
ns
P
Notes:
1.
Setup and hold times are measured over worst case conditions (process, voltage, temperature). Setup time is measured relative to the
global clock input signal using the slowest process, slowest temperature, and slowest voltage. Hold time is measured relative to the
global clock input signal using the fastest process, fastest temperature, and fastest voltage.
2.
This table lists representative values where one global clock input drives one vertical clock line in each accessible column, and where all
accessible I/O and CLB flip-flops are clocked by the global clock net.
3.
Use IBIS to determine any duty-cycle distortion incurred using various standards.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
41
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 46: Sampling Window
Speed Grade and VCCINT Operating Voltages
Description
TSAMP_BUFG
1
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
510
610
610
610
610
ps
TSAMP_NATIVE_DPA2
100
100
125
125
150
ps
TSAMP_NATIVE_BISC3
60
60
85
85
110
ps
Notes:
1.
This parameter indicates the total sampling error of the Kintex UltraScale+ FPGA DDR input registers, measured across voltage,
temperature, and process. The characterization methodology uses the MMCM to capture the DDR input registers' edges of operation.
These measurements include: CLK0 MMCM jitter, MMCM accuracy (phase offset), and MMCM phase shift resolution. These
measurements do not include package or clock tree skew.
2.
This parameter is the receive sampling error for RX_BITSLICE when using dynamic phase alignment.
3.
This parameter is the receive sampling error for RX_BITSLICE when using built-in self-calibration (BISC).
Table 47: Input Logic Characteristics for Dynamic Phase Aligned Applications (Component Mode)
Speed Grade and VCCINT Operating Voltages
Description
0.90V
-3
0.85V
-2
0.72V
-1
-2
Units
-1
TINPUT_LOGIC_UNCERTAINTY1
40
ps
TCAL_ERROR2
24
ps
Notes:
1.
Input_logic_uncertainty accounts for the setup/hold and any pattern dependent jitter for the input logic (input register, IDDRE1, or
ISERDESE3).
2.
Calibration error associated with quantization effects based on the IDELAY resolution. Calibration must be performed for each input pin
to ensure optimal performance.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
42
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Package Parameter Guidelines
The parameters in this section provide the necessary values for calculating timing budgets for clock transmitter
and receiver data-valid windows.
Table 48: Package Skew
Symbol
PKGSKEW
Description
Package
Skew1, 2
Device
Value
Units
SFVB784
75
ps
FFVA676
136
ps
FFVB676
69
ps
FFVD900
179
ps
SFVB784
75
ps
FFVA676
136
ps
FFVB676
69
ps
FFVD900
179
ps
XCKU9P
FFVE900
212
ps
XCKU11P
FFVD900
146
ps
FFVA1156
170
ps
XCKU3P
XCKU5P
Package
FFVE1517
178
ps
XCKU13P
FFVE900
197
ps
XCKU15P
FFVA1156
203
ps
FFVE1517
167
ps
FFVA1760
191
ps
XCKU19P
XQKU5P
XQKU15P
FFVE1760
172
ps
FFVJ1760
187
ps
FFVB2104
196
ps
FFRB676
70
ps
SFRB784
75
ps
FFRA1156
201
ps
FFRE1517
161
ps
Notes:
1.
These values represent the worst-case skew between any two SelectIO resources in the package: shortest delay to longest delay from
die pad to ball.
2.
Package delay information is available for these device/package combinations. This information can be used to deskew the package.
GTH Transceiver Specifications
The UltraScale Architecture and Product Data Sheet: Overview (DS890) lists the Kintex UltraScale+ FPGAs that
include the GTH transceivers.
GTH Transceiver DC Input and Output Levels
The following table summarizes the DC specifications of the GTH transceivers in Kintex UltraScale+ FPGAs.
Consult the UltraScale Architecture GTH Transceivers User Guide (UG576) for further details.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
43
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 49: GTH Transceiver DC Specifications
Symbol
DVPPIN
DC Parameter
Conditions
Differential peak-to-peak input voltage
(external AC coupled)
Min
Typ
Max
Units
>10.3125 Gb/s
150
–
1250
mV
6.6 Gb/s to 10.3125 Gb/s
150
–
1250
mV
≤ 6.6 Gb/s
150
–
2000
mV
VIN
Single-ended input voltage. Voltage
measured at the pin referenced to
GND
DC coupled VMGTAVTT = 1.2V
–400
–
VMGTAVTT
mV
VCMIN
Common mode input voltage
DC coupled VMGTAVTT = 1.2V
–
2/3 VMGTAVTT
–
mV
DVPPOUT
Differential peak-to-peak output
voltage1
Transmitter output swing is set to
11111
800
–
–
mV
VCMOUTDC
Common mode output voltage: DC
coupled (equation based)
When remote RX is terminated to
GND
When remote RX termination is
floating
VMGTAVTT/2 – DVPPOUT/4
mV
VMGTAVTT – DVPPOUT/2
mV
When remote RX is terminated to
VRX_TERM2
mV
VCMOUTAC
Common mode output voltage: AC coupled (equation based)
RIN
Differential input resistance
–
100
–
Ω
ROUT
Differential output resistance
–
100
–
Ω
TOSKEW
Transmitter output pair (TXP and TXN) intra-pair skew (all packages)
–
–
10
ps
–
100
–
nF
CEXT
Recommended external AC coupling
capacitor3
VMGTAVTT – DVPPOUT/2
mV
Notes:
1.
The output swing and pre-emphasis levels are programmable using the attributes discussed in the UltraScale Architecture GTH
Transceivers User Guide (UG576), and can result in values lower than reported in this table.
2.
VRX_TERM is the remote RX termination voltage.
3.
Other values can be used as appropriate to conform to specific protocols and standards.
Figure 3: Single-Ended Peak-to-Peak Voltage
+V
P
Single-Ended
Peak-to-Peak
Voltage
N
0
X16653-072117
Figure 4: Differential Peak-to-Peak Voltage
+V
Differential
Peak-to-Peak
Voltage
0
–V
P–N
Differential peak-to-peak voltage = (Single-ended peak-to-peak voltage) x 2
X16639-072117
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
44
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 50 and Table 51 summarize the DC specifications of the GTH transceivers input and output clocks in
Kintex UltraScale+ FPGAs. Consult the UltraScale Architecture GTH Transceivers User Guide (UG576) for further
details.
Table 50: GTH Transceiver Clock Input Level Specification
Symbol
DC Parameter
Min
Typ
Max
Units
250
–
2000
mV
VIDIFF
Differential peak-to-peak input voltage
RIN
Differential input resistance
–
100
–
Ω
CEXT
Required external AC coupling capacitor
–
10
–
nF
Table 51: GTH Transceiver Clock Output Level Specification
Symbol
Description
Conditions
Min
Typ
Max
Units
VOL
Output Low voltage for P and N
RT = 100Ω across P and N signals
100
–
330
mV
VOH
Output High voltage for P and N
RT = 100Ω across P and N signals
500
–
700
mV
VDDOUT
Differential output voltage (P–N), P =
High (N–P), N = High
RT = 100Ω across P and N signals
300
–
430
mV
VCMOUT
Common mode voltage
RT = 100Ω across P and N signals
300
–
500
mV
GTH Transceiver Switching Characteristics
Consult the UltraScale Architecture GTH Transceivers User Guide (UG576) for further information.
Table 52: GTH Transceiver Performance
Symbol
Description
Speed Grade and VCCINT Operating Voltages
Output
Divider
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
FGTHMAX
GTH maximum line rate
16.375
16.375
12.5
12.5
10.3125
Gb/s
FGTHMIN
GTH minimum line rate
0.5
0.5
0.5
0.5
0.5
Gb/s
FGTHCRANGE
CPLL line rate
range1
Min
Max
Min
Max
Min
Max
Min
1
4
12.5
4
12.5
2
2
6.25
2
6.25
4
1
3.125
1
8
0.5
1.5625
0.5
4
8.5
2
4.25
3.125
1
1.5625
0.5
16
FGTHQRANGE1
Max
Min
Max
4
8.5
4
8.5
Gb/s
2
4.25
2
4.25
Gb/s
2.125
1
2.125
1
2.125
Gb/s
1.0625
0.5
1.0625
0.5
1.0625
Gb/s
N/A
Gb/s
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
1
9.8
16.375
9.8
16.375
9.8
12.5
9.8
12.5
9.8
10.3125
Gb/s
2
4.9
8.1875
4.9
8.1875
4.9
8.15
4.9
8.1875
4.9
8.15
Gb/s
4
2.45
4.0938
2.45
4.0938
2.45
4.075
2.45
4.0938
2.45
4.075
Gb/s
8
1.225
2.0469
1.225
2.0469
1.225
2.0375
1.225
2.0469
1.225
2.0375
Gb/s
16
0.6125
1.0234
0.6125
1.0234
0.6125
1.0188
0.6125
1.0234
0.6125
1.0188
Gb/s
QPLL0 line rate
range2
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
45
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 52: GTH Transceiver Performance (cont'd)
Symbol
FGTHQRANGE2
Description
Speed Grade and VCCINT Operating Voltages
Output
Divider
QPLL1 line rate
range3
0.90V
0.85V
-3
0.72V
-2
-1
Units
-2
-1
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
1
8.0
13.0
8.0
13.0
8.0
12.5
8.0
12.5
8.0
10.3125
Gb/s
2
4.0
6.5
4.0
6.5
4.0
6.5
4.0
6.5
4.0
6.5
Gb/s
4
2.0
3.25
2.0
3.25
2.0
3.25
2.0
3.25
2.0
3.25
Gb/s
8
1.0
1.625
1.0
1.625
1.0
1.625
1.0
1.625
1.0
1.625
Gb/s
Gb/s
16
0.5
0.8125
0.5
0.8125
0.5
0.8125
0.5
0.8125
0.5
0.8125
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
2
6.25
2
6.25
2
4.25
2
4.25
2
4.25
GHz
FCPLLRANGE
CPLL frequency range
FQPLL0RANGE
QPLL0 frequency range
9.8
16.375
9.8
16.375
9.8
16.375
9.8
16.375
9.8
16.375
GHz
FQPLL1RANGE
QPLL1 frequency range
8
13
8
13
8
13
8
13
8
13
GHz
Notes:
1.
The values listed are the rounded results of the calculated equation (2 × CPLL_Frequency)/Output_Divider.
2.
The values listed are the rounded results of the calculated equation (QPLL0_Frequency)/Output_Divider.
3.
The values listed are the rounded results of the calculated equation (QPLL1_Frequency)/Output_Divider.
Table 53: GTH Transceiver Dynamic Reconfiguration Port (DRP) Switching Characteristics
Symbol
FGTHDRPCLK
Description
GTHDRPCLK maximum frequency
All Speed Grades
Units
250
MHz
Table 54: GTH Transceiver Reference Clock Switching Characteristics
Symbol
FGCLK
Description
Conditions
Reference clock frequency range
All Speed Grades
Min
Typ
Max
60
–
820
Units
MHz
TRCLK
Reference clock rise time
20% – 80%
–
200
–
ps
TFCLK
Reference clock fall time
80% – 20%
–
200
–
ps
TDCREF
Reference clock duty cycle
Transceiver PLL only
40
50
60
%
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
46
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 55: GTH Transceiver Reference Clock Oscillator Selection Phase Noise Mask
Symbol
QPLLREFCLKMASK1, 2
CPLLREFCLKMASK1, 2
Offset
Frequency
Description
QPLL0/QPLL1 reference clock select phase noise
mask at REFCLK frequency = 312.5 MHz
CPLL reference clock select phase noise mask at
REFCLK frequency = 312.5 MHz
Min
Typ
Max
Units
10 kHz
–
–
–105
dBc/Hz
100 kHz
–
–
–124
1 MHz
–
–
–130
10 kHz
–
–
–105
100 kHz
–
–
–124
1 MHz
–
–
–130
50 MHz
–
–
–140
dBc/Hz
Notes:
1.
For reference clock frequencies other than 312.5 MHz, adjust the phase-noise mask values by 20 × Log(N/312.5) where N is the new
reference clock frequency in MHz.
2.
This reference clock phase-noise mask is superseded by any reference clock phase-noise mask that is specified in a supported protocol,
e.g., PCIe.
Table 56: GTH Transceiver PLL/Lock Time Adaptation
Symbol
TLOCK
TDLOCK
Description
All Speed Grades
Conditions
Initial PLL lock
Clock recovery phase acquisition and
adaptation time for decision feedback
equalizer (DFE)
Clock recovery phase acquisition and
adaptation time for low-power mode (LPM)
when the DFE is disabled
After the PLL is locked to the
reference clock, this is the time
it takes to lock the clock data
recovery (CDR) to the data
present at the input.
Min
Typ
Max
–
–
1
Units
ms
106
UI
UI
–
50,000
37 x
–
50,000
2.3 x 106
Table 57: GTH Transceiver User Clock Switching Characteristics
Symbol
Description1
Data Width Conditions
(Bit)
Internal
Logic
Interconnect
Logic
Speed Grade and VCCINT Operating Voltages
0.90V
0.85V
0.72V
Units
-32
-22, 3
-14, 5
-23
-15
FTXOUTPMA
TXOUTCLK maximum frequency sourced from
OUTCLKPMA
511.719
511.719
390.625
390.625
322.266
MHz
FRXOUTPMA
RXOUTCLK maximum frequency sourced from
OUTCLKPMA
511.719
511.719
390.625
390.625
322.266
MHz
FTXOUTPROGDIV
TXOUTCLK maximum frequency sourced from
TXPROGDIVCLK
511.719
511.719
511.719
511.719
511.719
MHz
FRXOUTPROGDIV
RXOUTCLK maximum frequency sourced from
RXPROGDIVCLK
511.719
511.719
511.719
511.719
511.719
MHz
FTXIN
TXUSRCLK6
maximum
frequency
511.719
511.719
390.625
390.625
322.266
MHz
DS922 (v1.17) February 16, 2021
Product Specification
16
16, 32
32
32, 64
511.719
511.719
390.625
390.625
322.266
MHz
20
20, 40
409.375
409.375
312.500
312.500
257.813
MHz
40
40, 80
409.375
409.375
312.500
312.500
257.813
MHz
Send Feedback
www.xilinx.com
47
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 57: GTH Transceiver User Clock Switching Characteristics (cont'd)
Symbol
Description1
Data Width Conditions
(Bit)
0.72V
Units
-32
-22, 3
-14, 5
-23
-15
16
16, 32
511.719
511.719
390.625
390.625
322.266
MHz
32
32, 64
511.719
511.719
390.625
390.625
322.266
MHz
20
20, 40
409.375
409.375
312.500
312.500
257.813
MHz
40
40, 80
409.375
409.375
312.500
312.500
257.813
MHz
16
16
511.719
511.719
390.625
390.625
322.266
MHz
16
32
255.859
255.859
195.313
195.313
161.133
MHz
32
32
511.719
511.719
390.625
390.625
322.266
MHz
32
64
255.859
255.859
195.313
195.313
161.133
MHz
20
20
409.375
409.375
312.500
312.500
257.813
MHz
20
40
204.688
204.688
156.250
156.250
128.906
MHz
40
40
409.375
409.375
312.500
312.500
257.813
MHz
40
80
204.688
204.688
156.250
156.250
128.906
MHz
16
16
511.719
511.719
390.625
390.625
322.266
MHz
16
32
255.859
255.859
195.313
195.313
161.133
MHz
32
32
511.719
511.719
390.625
390.625
322.266
MHz
32
64
255.859
255.859
195.313
195.313
161.133
MHz
20
20
409.375
409.375
312.500
312.500
257.813
MHz
20
40
204.688
204.688
156.250
156.250
128.906
MHz
40
40
409.375
409.375
312.500
312.500
257.813
MHz
40
80
204.688
204.688
156.250
156.250
128.906
MHz
maximum
frequency
RXUSRCLK26
FRXIN2
0.85V
Interconnect
Logic
TXUSRCLK26
FTXIN2
0.90V
Internal
Logic
RXUSRCLK6
maximum
frequency
FRXIN
Speed Grade and VCCINT Operating Voltages
maximum
frequency
Notes:
1.
Clocking must be implemented as described in UltraScale Architecture GTH Transceivers User Guide (UG576).
2.
For speed grades -3E, -2E, and -2I, a 16-bit and 20-bit internal data path can only be used for line rates less than 8.1875 Gb/s.
3.
For speed grade -2LE, a 16-bit and 20-bit internal data path can only be used for line rates less than 8.1875 Gb/s when VCCINT = 0.85V or
6.25 Gb/s when VCCINT = 0.72V.
4.
For speed grades -1E, -1I, and -1M, a 16-bit and 20-bit internal data path can only be used for line rates less than 6.25 Gb/s.
5.
For speed grade -1LI, a 16-bit and 20-bit internal data path can only be used for line rates less than 6.25 Gb/s when VCCINT = 0.85V or
5.15625 Gb/s when VCCINT = 0.72V.
6.
When the gearbox is used, these maximums refer to the XCLK. For more information, see the UltraScale Architecture GTH Transceivers User
Guide (UG576).
Table 58: GTH Transceiver Transmitter Switching Characteristics
Symbol
FGTHTX
Description
Condition
Serial data rate range
Min
Typ
Max
Units
0.500
–
FGTHMAX
Gb/s
TRTX
TX rise time
20%–80%
–
21
–
ps
TFTX
TX fall time
80%–20%
–
21
–
ps
TLLSKEW
TX lane-to-lane skew1
–
–
500.00
ps
–
–
0.28
UI
–
–
0.17
UI
TJ16.375
DJ16.375
Total
jitter2, 4
Deterministic
16.375 Gb/s
jitter2, 4
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
48
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 58: GTH Transceiver Transmitter Switching Characteristics (cont'd)
Symbol
TJ15.0
Description
Total jitter2, 4
DJ15.0
Deterministic
TJ14.1
jitter2, 4
Total
Total jitter2, 4
DJ14.1
Deterministic jitter2, 4
Total
DJ12.5_QPLL
Deterministic jitter2, 4
TJ12.5_CPLL
Total jitter3, 4
TJ11.3_QPLL
jitter2, 4
Total
DJ10.3125_QPLL
Deterministic jitter2, 4
jitter3, 4
TJ9.953_QPLL
Total
Deterministic jitter2, 4
TJ9.953_CPLL
Total jitter3, 4
TJ8.0
Total
Total jitter3, 4
DJ6.6
Deterministic jitter3, 4
jitter3, 4
TJ4.25
Total
jitter3, 4
DJ4.25
Deterministic jitter3, 4
TJ4.0
Total jitter3, 4
Total
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
–
–
0.33
UI
–
–
0.17
UI
11.3 Gb/s
–
–
0.28
UI
–
–
0.17
UI
10.3125 Gb/s
–
–
0.28
UI
–
–
0.17
UI
–
–
0.33
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
–
–
0.33
UI
–
–
0.17
UI
8.0 Gb/s
–
–
0.32
UI
–
–
0.17
UI
6.6 Gb/s
–
–
0.30
UI
–
–
0.15
UI
–
–
0.30
UI
–
–
0.15
UI
–
–
0.30
UI
–
–
0.15
UI
–
–
0.32
UI
–
–
0.16
UI
–
–
0.20
UI
–
–
0.10
UI
–
–
0.20
UI
–
–
0.10
UI
–
–
0.15
UI
–
–
0.06
UI
3.20
Gb/s5
jitter3, 4
Total jitter3, 4
DJ2.5
Deterministic jitter3, 4
2.5 Gb/s6
jitter3, 4
Deterministic
UI
0.28
4.0 Gb/s
Deterministic
DJ1.25
0.17
–
jitter3, 4
TJ2.5
Total
–
–
4.25 Gb/s
DJ3.20
TJ1.25
–
5.0 Gb/s
Deterministic
TJ3.20
UI
jitter3, 4
DJ5.0
jitter3, 4
0.28
jitter3, 4
Deterministic
Deterministic
–
9.953 Gb/s
jitter3, 4
DJ4.0
–
jitter3, 4
TJ6.6
Total
UI
9.953 Gb/s
DJ8.0
TJ5.0
0.17
10.3125 Gb/s
jitter2, 4
Deterministic
–
jitter3, 4
DJ9.953_QPLL
DJ9.953_CPLL
–
jitter2, 4
Deterministic
Deterministic
UI
12.5 Gb/s
Total jitter2, 4
DJ10.3125_CPLL
0.28
jitter3, 4
TJ10.3125_QPLL
Total
–
12.5 Gb/s
DJ11.3_QPLL
TJ10.3125_CPLL
–
13.1 Gb/s
TJ12.5_QPLL
Deterministic
15.0 Gb/s
jitter2, 4
jitter2, 4
DJ12.5_CPLL
Units
14.025 Gb/s
jitter2, 4
Deterministic
Max
14.1 Gb/s
Deterministic
DJ13.1
Typ
jitter2, 4
TJ14.1
Total
Min
jitter2, 4
DJ14.1
TJ13.1
Condition
1.25 Gb/s7
jitter3, 4
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
49
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 58: GTH Transceiver Transmitter Switching Characteristics (cont'd)
Symbol
Description
Condition
Min
Typ
Max
Units
500 Mb/s8
–
–
0.10
UI
–
–
0.03
UI
Total jitter3, 4
TJ500
DJ500
Deterministic
jitter3, 4
Notes:
1.
Using same REFCLK input with TX phase alignment enabled for up to four consecutive transmitters (one fully populated GTH Quad) at
the maximum line rate.
2.
Using QPLL_FBDIV = 40, 20-bit internal data width. These values are NOT intended for protocol specific compliance determinations.
3.
Using CPLL_FBDIV = 2, 20-bit internal data width. These values are NOT intended for protocol specific compliance determinations.
4.
All jitter values are based on a bit-error ratio of 10–12.
5.
CPLL frequency at 3.2 GHz and TXOUT_DIV = 2.
6.
CPLL frequency at 2.5 GHz and TXOUT_DIV = 2.
7.
CPLL frequency at 2.5 GHz and TXOUT_DIV = 4.
8.
CPLL frequency at 2.0 GHz and TXOUT_DIV = 8.
Table 59: GTH Transceiver Receiver Switching Characteristics
Symbol
Description
FGTHRX
Serial data rate
RXSST
Receiver spread-spectrum tracking1
RXRL
Run length (CID)
RXPPMTOL
Data/REFCLK PPM offset tolerance
SJ Jitter
Condition
Min
Typ
Max
Units
0.500
–
FGTHMAX
Gb/s
–5000
–
0
ppm
–
–
256
UI
Bit rates ≤ 6.6 Gb/s
–1250
–
1250
ppm
Bit rates > 6.6 Gb/s and
≤ 8.0 Gb/s
–700
–
700
ppm
Bit rates > 8.0 Gb/s
–200
–
200
ppm
Modulated at 33 kHz
Tolerance2
JT_SJ16.375
Sinusoidal jitter (QPLL)3
16.375 Gb/s
0.30
–
–
UI
JT_SJ15.0
Sinusoidal jitter (QPLL)3
15.0 Gb/s
0.30
–
–
UI
JT_SJ14.1
Sinusoidal jitter
(QPLL)3
14.1 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(QPLL)3
13.1 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(QPLL)3
12.5 Gb/s
0.30
–
–
UI
JT_SJ11.3
Sinusoidal jitter
(QPLL)3
11.3 Gb/s
0.30
–
–
UI
JT_SJ10.32_QPLL
Sinusoidal jitter (QPLL)3
10.32 Gb/s
0.30
–
–
UI
JT_SJ10.32_CPLL
Sinusoidal jitter
(CPLL)3
10.32 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(QPLL)3
9.953 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(CPLL)3
9.953 Gb/s
0.30
–
–
UI
JT_SJ8.0
Sinusoidal jitter
(QPLL)3
8.0 Gb/s
0.42
–
–
UI
JT_SJ6.6_CPLL
Sinusoidal jitter (CPLL)3
6.6 Gb/s
0.44
–
–
UI
Sinusoidal jitter
(CPLL)3
5.0 Gb/s
0.44
–
–
UI
Sinusoidal jitter
(CPLL)3
4.25 Gb/s
0.44
–
–
UI
Sinusoidal jitter
(CPLL)3
3.2
Gb/s4
0.45
–
–
UI
JT_SJ2.5
Sinusoidal jitter
(CPLL)3
2.5
Gb/s5
0.30
–
–
UI
JT_SJ1.25
Sinusoidal jitter (CPLL)3
1.25 Gb/s6
0.30
–
–
UI
JT_SJ500
(CPLL)3
Mb/s7
0.30
–
–
UI
JT_SJ13.1
JT_SJ12.5
JT_SJ9.953_QPLL
JT_SJ9.953_CPLL
JT_SJ5.0
JT_SJ4.25
JT_SJ3.2
Sinusoidal jitter
DS922 (v1.17) February 16, 2021
Product Specification
500
Send Feedback
www.xilinx.com
50
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 59: GTH Transceiver Receiver Switching Characteristics (cont'd)
Symbol
Description
Condition
Min
Typ
Max
Units
3.2 Gb/s
0.70
–
–
UI
6.6 Gb/s
0.70
–
–
UI
3.2 Gb/s
0.10
–
–
UI
6.6 Gb/s
0.10
–
–
UI
SJ Jitter Tolerance with Stressed Eye2
Total jitter with stressed eye8
JT_TJSE3.2
JT_TJSE6.6
JT_SJSE3.2
Sinusoidal jitter with stressed
eye8
JT_SJSE6.6
Notes:
1.
Using RXOUT_DIV = 1, 2, and 4.
2.
All jitter values are based on a bit error ratio of 10–12.
3.
The frequency of the injected sinusoidal jitter is 80 MHz.
4.
CPLL frequency at 3.2 GHz and RXOUT_DIV = 2.
5.
CPLL frequency at 2.5 GHz and RXOUT_DIV = 2.
6.
CPLL frequency at 2.5 GHz and RXOUT_DIV = 4.
7.
CPLL frequency at 2.0 GHz and RXOUT_DIV = 8.
8.
Composite jitter with RX equalizer enabled. DFE disabled.
GTH Transceiver Electrical Compliance
The UltraScale Architecture GTH Transceivers User Guide (UG576) contains recommended use modes that ensure
compliance for the protocols listed in the following table. The transceiver wizard provides the recommended
settings for those use cases and for protocol specific characteristics.
Table 60: GTH Transceiver Protocol List
Protocol
Specification
Serial Rate (Gb/s)
Electrical
Compliance
CAUI-10
IEEE 802.3-2012
10.3125
Compliant
nPPI
IEEE 802.3-2012
10.3125
Compliant
10GBASE-KR1
IEEE 802.3-2012
10.3125
Compliant
40GBASE-KR
IEEE 802.3-2012
10.3125
Compliant
SFP+
SFF-8431 (SR and LR)
9.95328–11.10
Compliant
XFP
INF-8077i, revision 4.5
10.3125
Compliant
RXAUI
CEI-6G-SR
6.25
Compliant
XAUI
IEEE 802.3-2012
3.125
Compliant
1000BASE-X
IEEE 802.3-2012
1.25
Compliant
5.0G Ethernet
IEEE 802.3bx (PAR)
5
Compliant
2.5G Ethernet
IEEE 802.3bx (PAR)
2.5
Compliant
HiGig, HiGig+, HiGig2
IEEE 802.3-2012
3.74, 6.6
Compliant
OTU2
ITU G.8251
10.709225
Compliant
OTU4 (OTL4.10)
OIF-CEI-11G-SR
11.180997
Compliant
OC-3/12/48/192
GR-253-CORE
0.1555–9.956
Compliant
TFI-5
OIF-TFI5-0.1.0
2.488
Compliant
Interlaken
OIF-CEI-6G, OIF-CEI-11G-SR
4.25–12.5
Compliant
PCIe Gen1, 2, 3
PCI Express base 3.0
2.5, 5.0, and 8.0
Compliant
SDI2
SMPTE 424M-2006
0.27–2.97
Compliant
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
51
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 60: GTH Transceiver Protocol List (cont'd)
Protocol
Specification
Serial Rate (Gb/s)
Electrical
Compliance
UHD-SDI2
SMPTE ST-2081 6G, SMPTE ST-2082 12G
6 and 12
Compliant
Hybrid memory cube (HMC)
HMC-15G-SR
10, 12.5, and 15.0
Compliant
MoSys Bandwidth Engine
CEI-11-SR and CEI-11-SR (overclocked)
10.3125, 15.5
Compliant
CPRI
CPRI_v_6_1_2014-07-01
0.6144–12.165
Compliant
HDMI2
HDMI 2.0
All
Compliant
Passive optical network (PON)
10G-EPON, 1G-EPON, NG-PON2, XG-PON, and 2.5GPON
0.155–10.3125
Compliant
JESD204a/b
OIF-CEI-6G, OIF-CEI-11G
3.125–12.5
Compliant
Serial RapidIO
RapidIO specification 3.1
1.25–10.3125
Compliant
DisplayPort2
DP 1.2B CTS
1.62–5.4
Compliant
Fibre channel
FC-PI-4
1.0625–14.025
Compliant
SATA Gen1, 2, 3
Serial ATA revision 3.0 specification
1.5, 3.0, and 6.0
Compliant
SAS Gen1, 2, 3
T10/BSR INCITS 519
3.0, 6.0, and 12.0
Compliant
SFI-5
OIF-SFI5-01.0
0.625–12.5
Compliant
Aurora
CEI-6G, CEI-11G-LR
up to 11.180997
Compliant
Notes:
1.
The transition time of the transmitter is faster than the IEEE Std 802.3-2012 specification.
2.
This protocol requires external circuitry to achieve compliance.
GTY Transceiver Specifications
The UltraScale Architecture and Product Data Sheet: Overview (DS890) lists the Kintex UltraScale+ FPGAs that
include the GTY transceivers.
GTY Transceiver DC Input and Output Levels
Table 61 summarizes the DC specifications of the GTY transceivers in Kintex UltraScale+ FPGAs. Consult the
UltraScale Architecture GTY Transceivers User Guide (UG578) for further details.
Table 61: GTY Transceiver DC Specifications
Symbol
DVPPIN
DC Parameter
Differential peak-to-peak input voltage
(external AC coupled)
Conditions
Min
Typ
Max
Units
>10.3125 Gb/s
150
–
1250
mV
6.6 Gb/s to 10.3125 Gb/s
150
–
1250
mV
≤ 6.6 Gb/s
150
–
2000
mV
VIN
Single-ended input voltage. Voltage
measured at the pin referenced to
GND.
DC coupled VMGTAVTT = 1.2V
–400
–
VMGTAVTT
mV
VCMIN
Common mode input voltage
DC coupled VMGTAVTT = 1.2V
–
2/3 VMGTAVTT
–
mV
DVPPOUT
Differential peak-to-peak output
voltage1
Transmitter output swing is set
to 11111
800
–
–
mV
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
52
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 61: GTY Transceiver DC Specifications (cont'd)
Symbol
VCMOUTDC
DC Parameter
Conditions
Common mode output voltage: DC
coupled (equation based)
Min
When remote RX is terminated to
GND
When remote RX termination is
floating
Typ
Max
Units
VMGTAVTT/2 – DVPPOUT/4
mV
VMGTAVTT – DVPPOUT/2
mV
When remote RX is terminated to
VRX_TERM2
VCMOUTAC
Common mode output voltage: AC
coupled
RIN
Differential input resistance
mV
Equation based
VMGTAVTT – DVPPOUT/2
–
100
mV
–
Ω
ROUT
Differential output resistance
–
100
–
Ω
TOSKEW
Transmitter output pair (TXP and TXN) intra-pair skew
–
–
10
ps
CEXT
Recommended external AC coupling capacitor3
–
100
–
nF
Notes:
1.
The output swing and pre-emphasis levels are programmable using the GTY transceiver attributes discussed in the UltraScale Architecture
GTY Transceivers User Guide (UG578) and can result in values lower than reported in this table.
2.
VRX_TERM is the remote RX termination voltage.
3.
Other values can be used as appropriate to conform to specific protocols and standards.
Figure 5: Single-Ended Peak-to-Peak Voltage
+V
P
Single-Ended
Peak-to-Peak
Voltage
N
0
X16653-072117
Figure 6: Differential Peak-to-Peak Voltage
+V
Differential
Peak-to-Peak
Voltage
0
–V
P–N
Differential peak-to-peak voltage = (Single-ended peak-to-peak voltage) x 2
X16639-072117
The following tables summarize the DC specifications of the clock input/output levels of the GTY transceivers in
Kintex UltraScale+ FPGAs. Consult the UltraScale Architecture GTY Transceivers User Guide (UG578) for further
details.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
53
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 62: GTY Transceiver Clock DC Input Level Specification
Symbol
DC Parameter
Min
Typ
Max
Units
250
–
2000
mV
VIDIFF
Differential peak-to-peak input voltage
RIN
Differential input resistance
–
100
–
Ω
CEXT
Required external AC coupling capacitor
–
10
–
nF
Table 63: GTY Transceiver Clock Output Level Specification
Symbol
Description
Conditions
Min
Typ
Max
Units
VOL
Output Low voltage for P and N
RT = 100Ω across P and N signals
100
–
330
mV
VOH
Output High voltage for P and N
RT = 100Ω across P and N signals
500
–
700
mV
VDDOUT
Differential output voltage (P–N), P =
High (N–P), N = High
RT = 100Ω across P and N signals
300
–
430
mV
VCMOUT
Common mode voltage
RT = 100Ω across P and N signals
300
–
500
mV
GTY Transceiver Switching Characteristics
Consult the UltraScale Architecture GTY Transceivers User Guide (UG578) for further information.
Table 64: GTY Transceiver Performance
Speed Grade and VCCINT Operating Voltages
Output
Description
Divider
0.90V
-3
-2
-1
-2
-1
FGTYMAX
GTY maximum line rate
32.751
28.211
25.7851
28.211
12.5
Gb/s
FGTYMIN
GTY minimum line rate
0.5
0.5
0.5
0.5
0.5
Gb/s
FGTYCRANGE
CPLL line rate
range2
Symbol
FGTYQRANGE1
QPLL0 line rate
range3
0.85V
0.72V
Units
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
1
4.0
12.5
4.0
12.5
4.0
8.5
4.0
12.5
4.0
8.5
Gb/s
2
2.0
6.25
2.0
6.25
2.0
4.25
2.0
6.25
2.0
4.25
Gb/s
4
1.0
3.125
1.0
3.125
1.0
2.125
1.0
3.125
1.0
2.125
Gb/s
8
0.5
1.5625
0.5
1.5625
0.5
1.0625
0.5
1.5625
0.5
1.0625
Gb/s
16
N/A
Gb/s
32
N/A
Gb/s
Min
Max
Min
Max
Min
Max
Min
Max
1
19.6
32.75
19.6
28.21
19.6
25.785
19.6
28.21
1
9.8
16.375
9.8
16.375
9.8
16.375
9.8
16.375
2
4.9
8.1875
4.9
8.1875
4.9
8.1875
4.9
4
2.45
4.0938
2.45
4.0938
2.45
4.0938
2.45
8
1.225
2.0469
1.225
2.0469
1.225
2.0469
16
0.6125
1.0234
0.6125
1.0234
0.6125
1.0234
DS922 (v1.17) February 16, 2021
Product Specification
Min
Max
N/A
Gb/s
9.8
12.5
Gb/s
8.1875
4.9
8.1875
Gb/s
4.0938
2.45
4.0938
Gb/s
1.225
2.0469
1.225
2.0469
Gb/s
0.6125
1.0234
0.6125
1.0234
Gb/s
Send Feedback
www.xilinx.com
54
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 64: GTY Transceiver Performance (cont'd)
Symbol
FGTYQRANGE2
Speed Grade and VCCINT Operating Voltages
Output
Description
Divider
QPLL1 line rate
range4
0.90V
0.85V
-3
-2
0.72V
-1
-2
Units
-1
Min
Max
Min
Max
Min
Max
Min
Max
1
16.0
26.0
16.0
26.0
16.0
25.785
16.0
26.0
Min
Max
1
8.0
13.0
8.0
13.0
8.0
12.5
8.0
13.0
8.0
12.5
Gb/s
2
4.0
6.5
4.0
6.5
4.0
6.5
4.0
6.5
4.0
6.5
Gb/s
4
2.0
3.25
2.0
3.25
2.0
3.25
2.0
3.25
2.0
3.25
Gb/s
N/A
Gb/s
8
1.0
1.625
1.0
1.625
1.0
1.625
1.0
1.625
1.0
1.625
Gb/s
16
0.5
0.8125
0.5
0.8125
0.5
0.8125
0.5
0.8125
0.5
0.8125
Gb/s
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
FCPLLRANGE
CPLL frequency range
2.0
6.25
2.0
6.25
2.0
4.25
2.0
6.25
2.0
4.25
GHz
FQPLL0RANGE
QPLL0 frequency range
9.8
16.375
9.8
16.375
9.8
16.375
9.8
16.375
9.8
16.375
GHz
FQPLL1RANGE
QPLL1 frequency range
8.0
13.0
8.0
13.0
8.0
13.0
8.0
13.0
8.0
13.0
GHz
Notes:
1.
GTY transceiver line rates are package limited: SFVB784 and SFRB784 to 12.5 Gb/s; FFVA676, FFVD900, FFVA1156, and FFRA1156 to 16.3
Gb/s.
2.
The values listed are the rounded results of the calculated equation (2 × CPLL_Frequency)/Output_Divider.
3.
The values listed are the rounded results of the calculated equation ( QPLL0_Frequency × RATE)/Output_Divider where RATE is 1 when
QPLL0_CLKOUT_RATE is set to HALF and 2 if QPLL0_CLKOUT_RATE is set to FULL.
4.
The values listed are the rounded results of the calculated equation (QPLL1_Frequency × RATE)/Output_Divider where RATE is 1 when
QPLL1_CLKOUT_RATE is set to HALF and 2 if QPLL1_CLKOUT_RATE is set to FULL.
Table 65: GTY Transceiver Dynamic Reconfiguration Port (DRP) Switching Characteristics
Symbol
FGTYDRPCLK
Description
GTYDRPCLK maximum frequency
All Speed Grades
Units
250
MHz
Table 66: GTY Transceiver Reference Clock Switching Characteristics
Symbol
Description
Conditions
All Speed Grades
Min
Typ
Max
Units
FGCLK
Reference clock frequency range
60
–
820
MHz
TRCLK
Reference clock rise time
20% – 80%
–
200
–
ps
TFCLK
Reference clock fall time
80% – 20%
–
200
–
ps
TDCREF
Reference clock duty cycle
Transceiver PLL only
40
50
60
%
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
55
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 67: GTY Transceiver Reference Clock Oscillator Selection Phase Noise Mask
Description1, 2
Symbol
QPLLREFCLKMASK
QPLL0/QPLL1 reference clock select phase noise
mask at REFCLK frequency = 156.25 MHz
QPLL0/QPLL1 reference clock select phase noise
mask at REFCLK frequency = 312.5 MHz
QPLL0/QPLL1 reference clock select phase noise
mask at REFCLK frequency = 625 MHz
CPLLREFCLKMASK
CPLL reference clock select phase noise mask at
REFCLK frequency = 156.25 MHz
CPLL reference clock select phase noise mask at
REFCLK frequency = 312.5 MHz
CPLL reference clock select phase noise mask at
REFCLK frequency = 625 MHz
Offset
Frequency
Min
Typ
Max
Units
10 kHz
–
–
–112
dBc/Hz
100 kHz
–
–
–128
1 MHz
–
–
–145
10 kHz
–
–
–103
100 kHz
–
–
–123
1 MHz
–
–
–143
10 kHz
–
–
–98
100 kHz
–
–
–117
1 MHz
–
–
–140
10 kHz
–
–
–112
100 kHz
–
–
–128
1 MHz
–
–
–145
50 MHz
–
–
–145
10 kHz
–
–
–103
100 kHz
–
–
–123
1 MHz
–
–
–143
50 MHz
–
–
–145
10 kHz
–
–
–98
100 kHz
–
–
–117
1 MHz
–
–
–140
50 MHz
–
–
–144
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
Notes:
1.
For reference clock frequencies not in this table, use the phase-noise mask for the nearest reference clock frequency.
2.
This reference clock phase-noise mask is superseded by any reference clock phase-noise mask that is specified in a supported protocol,
e.g., PCIe.
Table 68: GTY Transceiver PLL/Lock Time Adaptation
Symbol
TLOCK
TDLOCK
Description
Conditions
Initial PLL lock.
Clock recovery phase acquisition and
adaptation time for decision feedback
equalizer (DFE)
Clock recovery phase acquisition and
adaptation time for low-power mode (LPM)
when the DFE is disabled
DS922 (v1.17) February 16, 2021
Product Specification
After the PLL is locked to the
reference clock, this is the
time it takes to lock the clock
data recovery (CDR) to the
data present at the input.
All Speed Grades
Min
Typ
Max
–
–
1
ms
106
UI
UI
–
50,000
37 x
–
50,000
2.3 x 106
Send Feedback
Units
www.xilinx.com
56
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 69: GTY Transceiver User Clock Switching Characteristics
Symbol
Description1
Data Width Conditions
(Bit)
Internal
Logic
Interconnect
Logic
Speed Grade and VCCINT Operating Voltages
0.90V
0.85V
0.72V
Units
-32
-22, 3
-1 4, 5, 6
-23
-15
FTXOUTPMA
TXOUTCLK maximum frequency sourced from
OUTCLKPMA
511.719
511.719
402.891
402.832
322.266
MHz
FRXOUTPMA
RXOUTCLK maximum frequency sourced from
OUTCLKPMA
511.719
511.719
402.891
402.832
322.266
MHz
FTXOUTPROGDIV
TXOUTCLK maximum frequency sourced from
TXPROGDIVCLK
511.719
511.719
511.719
511.719
511.719
MHz
FRXOUTPROGDIV
RXOUTCLK maximum frequency sourced from
RXPROGDIVCLK
511.719
511.719
511.719
511.719
511.719
MHz
FTXIN
TXUSRCLK7
maximum
frequency
16, 32
511.719
511.719
390.625
390.625
322.266
MHz
32
32, 64
511.719
511.719
390.625
390.625
322.266
MHz
64
64, 128
511.719
440.781
402.891
402.832
195.313
MHz
20
20, 40
409.375
409.375
312.500
312.500
257.813
MHz
40
40, 80
409.375
409.375
312.500
350.000
257.813
MHz
80
80, 160
409.375
352.625
322.313
352.625
156.250
MHz
FRXIN
FTXIN2
RXUSRCLK7
maximum
frequency
TXUSRCLK27
maximum
frequency
DS922 (v1.17) February 16, 2021
Product Specification
16
16
16, 32
511.719
511.719
390.625
390.625
322.266
MHz
32
32, 64
511.719
511.719
390.625
390.625
322.266
MHz
64
64, 128
511.719
440.781
402.891
402.832
195.313
MHz
20
20, 40
409.375
409.375
312.500
312.500
257.813
MHz
40
40, 80
409.375
409.375
312.500
350.000
257.813
MHz
80
80, 160
409.375
352.625
322.313
352.625
156.250
MHz
16
16
511.719
511.719
390.625
390.625
322.266
MHz
16
32
255.859
255.859
195.313
195.313
161.133
MHz
32
32
511.719
511.719
390.625
390.625
322.266
MHz
32
64
255.859
255.859
195.313
195.313
161.133
MHz
64
64
511.719
440.781
402.891
402.832
195.313
MHz
64
128
255.859
220.391
201.445
201.416
97.656
MHz
20
20
409.375
409.375
312.500
312.500
257.813
MHz
20
40
204.688
204.688
156.250
156.250
128.906
MHz
40
40
409.375
409.375
312.500
350.000
257.813
MHz
40
80
204.688
204.688
156.250
175.000
128.906
MHz
80
80
409.375
352.625
322.313
352.625
156.250
MHz
80
160
204.688
176.313
161.156
176.313
78.125
MHz
Send Feedback
www.xilinx.com
57
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 69: GTY Transceiver User Clock Switching Characteristics (cont'd)
Symbol
Data Width Conditions
(Bit)
Description1
0.90V
0.85V
0.72V
Units
Internal
Logic
Interconnect
Logic
-32
-22, 3
-1 4, 5, 6
-23
-15
16
16
511.719
511.719
390.625
390.625
322.266
MHz
16
32
255.859
255.859
195.313
195.313
161.133
MHz
32
32
511.719
511.719
390.625
390.625
322.266
MHz
32
64
255.859
255.859
195.313
195.313
161.133
MHz
64
64
511.719
440.781
402.891
402.832
195.313
MHz
64
128
255.859
220.391
201.445
201.416
97.656
MHz
20
20
409.375
409.375
312.500
312.500
257.813
MHz
20
40
204.688
204.688
156.250
156.250
128.906
MHz
40
40
409.375
409.375
312.500
350.000
257.813
MHz
40
80
204.688
204.688
156.250
175.000
128.906
MHz
80
80
409.375
352.625
322.313
352.625
156.250
MHz
80
160
204.688
176.313
161.156
176.313
78.125
MHz
RXUSRCLK27
maximum
frequency
FRXIN2
Speed Grade and VCCINT Operating Voltages
Notes:
1.
Clocking must be implemented as described in the UltraScale Architecture GTY Transceivers User Guide (UG578).
2.
For speed grades -3E, -2E, and -2I, a 16-bit and 20-bit internal data path can only be used for line rates less than 8.1875 Gb/s.
3.
For speed grade -2LE, a 16-bit and 20-bit internal data path can only be used for line rates less than 8.1875 Gb/s when VCCINT = 0.85V or
6.25 Gb/s when VCCINT = 0.72V.
4.
For speed grades -1E, -1I, and -1M, a 16-bit and 20-bit internal data path can only be used for line rates less than 6.25 Gb/s.
5.
For speed grade -1LI, a 16-bit and 20-bit internal data path can only be used for line rates less than 6.25 Gb/s when VCCINT = 0.85V or
5.15625 Gb/s when VCCINT = 0.72V.
6.
For the speed grades -1E, -1I, and -1M, only a 64- or 80-bit internal data path can be used for line rates above 12.5 Gb/s.
7.
When the gearbox is used, these maximums refer to the XCLK. For more information, see the Valid Data Width Combinations for TX
Asynchronous Gearbox table in the UltraScale Architecture GTY Transceivers User Guide (UG578).
Table 70: GTY Transceiver Transmitter Switching Characteristics
Symbol
Description
FGTYTX
Serial data rate range
TRTX
TX rise time
TFTX
TX fall time
TX lane-to-lane
TJ32.75
Total jitter2, 4
DJ32.75
Deterministic jitter2, 4
Total
Deterministic
jitter2, 4
Units
0.500
–
FGTYMAX
Gb/s
20%–80%
–
21
–
ps
80%–20%
–
21
–
ps
–
–
500.00
ps
–
–
0.35
UI
–
–
0.19
UI
–
–
0.28
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
28.21 Gb/s
TJ16.375
Total
Deterministic jitter2, 4
TJ15.0
Total jitter2, 4
Deterministic
Max
jitter2, 4
DJ16.375
DJ15.0
Typ
32.75 Gb/s
jitter2, 4
DJ28.21
Min
skew1
TLLSKEW
TJ28.21
Condition
16.375 Gb/s
15.0 Gb/s
jitter2, 4
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
58
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 70: GTY Transceiver Transmitter Switching Characteristics (cont'd)
Symbol
TJ14.1
Description
Total jitter2, 4
DJ14.1
Deterministic
TJ14.1
jitter2, 4
Total
Deterministic
Total jitter2, 4
DJ13.1
Deterministic jitter2, 4
jitter2, 4
TJ12.5_CPLL
Total
jitter3, 4
DJ12.5_CPLL
Deterministic jitter3, 4
TJ11.3_QPLL
Total jitter2, 4
TJ10.3125_QPLL
Total
Total jitter3, 4
DJ10.3125_CPLL
Deterministic jitter3, 4
jitter2, 4
jitter3, 4
Total
Deterministic jitter3, 4
TJ8.0
Total jitter3, 4
TJ6.6
jitter3, 4
Total
DJ5.0
Deterministic jitter3, 4
jitter3, 4
TJ3.20
Total
jitter3, 4
DJ3.20
Deterministic jitter3, 4
TJ2.5
Total jitter3, 4
DJ1.25
Total
Deterministic
–
0.28
UI
–
–
0.17
UI
13.1 Gb/s
–
–
0.28
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
–
–
0.33
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
10.3125 Gb/s
–
–
0.28
UI
–
–
0.17
UI
10.3125 Gb/s
–
–
0.33
UI
–
–
0.17
UI
–
–
0.28
UI
–
–
0.17
UI
–
–
0.33
UI
–
–
0.17
UI
–
–
0.32
UI
–
–
0.17
UI
6.6 Gb/s
–
–
0.30
UI
–
–
0.15
UI
5.0 Gb/s
–
–
0.30
UI
–
–
0.15
UI
–
–
0.30
UI
–
–
0.15
UI
–
–
0.20
UI
–
–
0.10
UI
–
–
0.20
UI
–
–
0.10
UI
–
–
0.15
UI
–
–
0.06
UI
4.25 Gb/s
Deterministic
TJ1.25
–
jitter3, 4
DJ4.25
jitter3, 4
14.025 Gb/s
jitter3, 4
Total jitter3, 4
Deterministic
UI
8.0 Gb/s
Deterministic
DJ2.5
0.17
jitter3, 4
TJ5.0
Total
–
9.953 Gb/s
DJ6.6
TJ4.25
–
9.953 Gb/s
TJ9.953_CPLL
Deterministic
UI
jitter2, 4
DJ9.953_CPLL
DJ8.0
0.28
jitter2, 4
Deterministic
Deterministic
–
11.3 Gb/s
jitter2, 4
DJ9.953_QPLL
–
jitter2, 4
TJ10.3125_CPLL
Total
14.1 Gb/s
12.5 Gb/s
DJ10.3125_QPLL
TJ9.953_QPLL
Units
12.5 Gb/s
Deterministic
Deterministic
Max
jitter2, 4
DJ12.5_QPLL
DJ11.3_QPLL
Typ
jitter2, 4
TJ13.1
Total
Min
jitter2, 4
DJ14.1
TJ12.5_QPLL
Condition
3.20
Gb/s5
2.5 Gb/s6
jitter3, 4
1.25
jitter3, 4
DS922 (v1.17) February 16, 2021
Product Specification
Gb/s7
Send Feedback
www.xilinx.com
59
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 70: GTY Transceiver Transmitter Switching Characteristics (cont'd)
Symbol
Description
Condition
Min
Typ
Max
Units
500 Mb/s8
–
–
0.10
UI
–
–
0.03
UI
Total jitter3, 4
TJ500
DJ500
Deterministic
jitter3, 4
Notes:
1.
Using same REFCLK input with TX phase alignment enabled for up to four consecutive transmitters (one fully populated GTY Quad) at
maximum line rate.
2.
Using QPLL_FBDIV = 40, 20-bit internal data width. These values are NOT intended for protocol specific compliance determinations.
3.
Using CPLL_FBDIV = 2, 20-bit internal data width. These values are NOT intended for protocol specific compliance determinations.
4.
All jitter values are based on a bit-error ratio of 10–12.
5.
CPLL frequency at 3.2 GHz and TXOUT_DIV = 2.
6.
CPLL frequency at 2.5 GHz and TXOUT_DIV = 2.
7.
CPLL frequency at 2.5 GHz and TXOUT_DIV = 4.
8.
CPLL frequency at 2.0 GHz and TXOUT_DIV = 8.
Table 71: GTY Transceiver Receiver Switching Characteristics
Symbol
Description
FGTYRX
Serial data rate
RXSST
Receiver spread-spectrum tracking1
RXRL
Run length (CID)
RXPPMTOL
Data/REFCLK PPM offset tolerance
SJ Jitter
Condition
Min
Typ
Max
Units
0.500
–
FGTYMAX
Gb/s
–5000
–
0
ppm
–
–
256
UI
Bit rates ≤ 6.6 Gb/s
–1250
–
1250
ppm
Bit rates > 6.6 Gb/s and
≤ 8.0 Gb/s
–700
–
700
ppm
Bit rates > 8.0 Gb/s
–200
–
200
ppm
Modulated at 33 kHz
Tolerance2
JT_SJ32.75
Sinusoidal jitter (QPLL)3
32.75 Gb/s
0.25
–
–
UI
JT_SJ28.21
Sinusoidal jitter (QPLL)3
28.21 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(QPLL)3
16.375 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(QPLL)3
15.0 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(QPLL)3
14.1 Gb/s
0.30
–
–
UI
JT_SJ13.1
Sinusoidal jitter
(QPLL)3
13.1 Gb/s
0.30
–
–
UI
JT_SJ12.5
Sinusoidal jitter (QPLL)3
12.5 Gb/s
0.30
–
–
UI
JT_SJ11.3
Sinusoidal jitter
(QPLL)3
11.3 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(QPLL)3
10.32 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(CPLL)3
10.32 Gb/s
0.30
–
–
UI
JT_SJ9.953_QPLL
Sinusoidal jitter
(QPLL)3
9.953 Gb/s
0.30
–
–
UI
JT_SJ9.953_CPLL
Sinusoidal jitter (CPLL)3
9.953 Gb/s
0.30
–
–
UI
Sinusoidal jitter
(CPLL)3
8.0 Gb/s
0.42
–
–
UI
Sinusoidal jitter
(CPLL)3
6.6 Gb/s
0.44
–
–
UI
Sinusoidal jitter
(CPLL)3
5.0 Gb/s
0.44
–
–
UI
JT_SJ4.25
Sinusoidal jitter
(CPLL)3
4.25 Gb/s
0.44
–
–
UI
JT_SJ3.2
Sinusoidal jitter (CPLL)3
3.2 Gb/s4
0.45
–
–
UI
JT_SJ2.5
Sinusoidal jitter
(CPLL)3
Gb/s5
Sinusoidal jitter
(CPLL)3
Sinusoidal jitter
(CPLL)3
JT_SJ16.375
JT_SJ15.0
JT_SJ14.1
JT_SJ10.32_QPLL
JT_SJ10.32_CPLL
JT_SJ8.0
JT_SJ6.6
JT_SJ5.0
JT_SJ1.25
JT_SJ500
DS922 (v1.17) February 16, 2021
Product Specification
2.5
0.30
–
–
UI
Gb/s6
0.30
–
–
UI
Mb/s7
0.30
–
–
UI
1.25
500
Send Feedback
www.xilinx.com
60
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 71: GTY Transceiver Receiver Switching Characteristics (cont'd)
Symbol
Description
Condition
Min
Typ
Max
Units
3.2 Gb/s
0.70
–
–
UI
6.6 Gb/s
0.70
–
–
UI
3.2 Gb/s
0.10
–
–
UI
6.6 Gb/s
0.10
–
–
UI
SJ Jitter Tolerance with Stressed Eye2
Total jitter with stressed eye8
JT_TJSE3.2
JT_TJSE6.6
JT_SJSE3.2
Sinusoidal jitter with stressed
eye8
JT_SJSE6.6
Notes:
1.
Using RXOUT_DIV = 1, 2, and 4.
2.
All jitter values are based on a bit error ratio of 10–12.
3.
The frequency of the injected sinusoidal jitter is 80 MHz.
4.
CPLL frequency at 3.2 GHz and RXOUT_DIV = 2.
5.
CPLL frequency at 2.5 GHz and RXOUT_DIV = 2.
6.
CPLL frequency at 2.5 GHz and RXOUT_DIV = 4.
7.
CPLL frequency at 2.0 GHz and RXOUT_DIV = 8.
8.
Composite jitter with RX equalizer enabled. DFE disabled.
GTY Transceiver Electrical Compliance
The UltraScale Architecture GTY Transceivers User Guide (UG578) contains recommended use modes that ensure
compliance for the protocols listed in the following table. The transceiver wizard provides the recommended
settings for those use cases and for protocol specific characteristics.
Table 72: GTY Transceiver Protocol List
Protocol
Specification
Serial Rate (Gb/s)
Electrical
Compliance
CAUI-4
IEEE 802.3-2012
25.78125
Compliant
28 Gb/s backplane
CEI-25G-LR
25–28.05
Compliant
Interlaken
OIF-CEI-6G, OIF-CEI-11GSR, OIF-CEI-28G-MR
4.25–25.78125
Compliant
100GBASE-KR4
IEEE 802.3bj-2014, CEI-25G-LR
25.78125
Compliant1
100GBASE-CR4
IEEE 802.3bj-2014, CEI-25G-LR
25.78125
Compliant1
50GBASE-KR4
IEEE 802.3by-2014, CEI-25G-LR
25.78125
Compliant1
50GBASE-CR4
IEEE 802.3by-2014, CEI-25G-LR
25.78125
Compliant1
25GBASE-KR4
IEEE 802.3by-2014, CEI-25G-LR
25.78125
Compliant1
25GBASE-CR4
IEEE 802.3by-2014, CEI-25G-LR
25.78125
Compliant1
OTU4 (OTL4.4) CFP2
OIF-CEI-28G-VSR
27.952493–32.75
Compliant
OTU4 (OTL4.4) CFP
OIF-CEI-11G-MR
11.18–13.1
Compliant
CAUI-10
IEEE 802.3-2012
10.3125
Compliant
nPPI
IEEE 802.3-2012
10.3125
Compliant
10GBASE-KR2
IEEE 802.3-2012
10.3125
Compliant
SFP+
SFF-8431 (SR and LR)
9.95328–11.10
Compliant
XFP
INF-8077i, revision 4.5
10.3125
Compliant
RXAUI
CEI-6G-SR
6.25
Compliant
XAUI
IEEE 802.3-2012
3.125
Compliant
1000BASE-X
IEEE 802.3-2012
1.25
Compliant
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
61
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 72: GTY Transceiver Protocol List (cont'd)
Protocol
Specification
Serial Rate (Gb/s)
Electrical
Compliance
5.0G Ethernet
IEEE 802.3bx (PAR)
5
Compliant
2.5G Ethernet
IEEE 802.3bx (PAR)
2.5
Compliant
HiGig, HiGig+, HiGig2
IEEE 802.3-2012
3.74, 6.6
Compliant
QSGMII
QSGMII v1.2 (Cisco System, ENG-46158)
5
Compliant
OTU2
ITU G.8251
10.709225
Compliant
OTU4 (OTL4.10)
OIF-CEI-11G-SR
11.180997
Compliant
OC-3/12/48/192
GR-253-CORE
0.1555–9.956
Compliant
PCIe Gen1, 2, 3
PCI Express base 3.0
2.5, 5.0, and 8.0
Compliant
SDI3
SMPTE 424M-2006
0.27–2.97
Compliant
UHD-SDI3
SMPTE ST-2081 6G, SMPTE ST-2082 12G
6 and 12
Compliant
Hybrid memory cube (HMC)
HMC-15G-SR
10, 12.5, and 15.0
Compliant
MoSys bandwidth engine
CEI-11-SR and CEI-11-SR (overclocked)
10.3125, 15.5
Compliant
CPRI
CPRI_v_6_1_2014-07-01
0.6144–12.165
Compliant
Passive optical network (PON)
10G-EPON, 1G-EPON, NG-PON2, XG-PON, and 2.5G-PON
0.155–10.3125
Compliant
JESD204a/b
OIF-CEI-6G, OIF-CEI-11G
3.125–12.5
Compliant
Serial RapidIO
RapidIO specification 3.1
1.25–10.3125
Compliant
DisplayPort
DP 1.2B CTS
1.62–5.4
Compliant3
Fibre channel
FC-PI-4
1.0625–14.025
Compliant
SATA Gen1, 2, 3
Serial ATA revision 3.0 specification
1.5, 3.0, and 6.0
Compliant
SAS Gen1, 2, 3
T10/BSR INCITS 519
3.0, 6.0, and 12.0
Compliant
SFI-5
OIF-SFI5-01.0
0.625 - 12.5
Compliant
Aurora
CEI-6G, CEI-11G-LR
All rates
Compliant
Notes:
1.
25 dB loss at Nyquist without FEC.
2.
The transition time of the transmitter is faster than the IEEE Std 802.3-2012 specification.
3.
This protocol requires external circuitry to achieve compliance.
Integrated Interface Block for Interlaken
More information and documentation on solutions using the integrated interface block for Interlaken can be
found at UltraScale+ Interlaken. The UltraScale Architecture and Product Data Sheet: Overview (DS890) lists how
many blocks are in each Kintex UltraScale+ FPGA. This section describes the following Interlaken
configurations.
• 12 x 12.5 Gb/s protocol and lane logic mode (Table 73).
• 6 x 25.78125 Gb/s and 6 x 28.21 Gb/s protocol and lane logic mode (Table 74).
• 12 x 25.78125 Gb/s lane logic only mode (Table 75).
Kintex UltraScale+ FPGAs in the SFVB784, SFRB784, FFVA676, FFVD900, FFVA1156, and FFRA1156
packages are only supported using the 12 x 12.5 Gb/s Interlaken configuration. See the FGTYMAX maximum line
rates.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
62
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 73: Maximum Performance for Interlaken 12 x 12.5 Gb/s Protocol and Lane Logic Mode
Designs
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
Units
0.72V
-3
-2
-1
-2
-1
FRX_SERDES_CLK
Receive serializer/
deserializer clock
195.32
195.32
195.32
195.32
195.32
MHz
FTX_SERDES_CLK
Transmit serializer/
deserializer clock
195.32
195.32
195.32
195.32
195.32
MHz
FDRP_CLK
Dynamic reconfiguration
port clock
250.00
250.00
250.00
250.00
250.00
MHz
Min1
Max
Min1
Max
Min1
Max
Min1
Max
Min1
Max
FCORE_CLK
Interlaken core clock
300.00
322.27
300.00
322.27
300.00
322.27
300.00
322.27
300.00
322.27
MHz
FLBUS_CLK
Interlaken local bus
clock
300.00
322.27
300.00
322.27
300.00
322.27
300.00
322.27
300.00
322.27
MHz
Notes:
1.
These are the minimum clock frequencies at the maximum lane performance.
Table 74: Maximum Performance for Interlaken 6 x 25.78125 Gb/s and 6 x 28.21 Gb/s Protocol and
Lane Logic Mode Designs
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-31
-21
-1
-2
-1
FRX_SERDES_CLK
Receive serializer/
deserializer clock
440.79
440.79
N/A
402.84
N/A
MHz
FTX_SERDES_CLK
Transmit serializer/
deserializer clock
440.79
440.79
N/A
402.84
N/A
MHz
FDRP_CLK
Dynamic reconfiguration
port clock
250.00
250.00
N/A
250.00
N/A
MHz
FCORE_CLK
FLBUS_CLK
Min2
Max
Min2
Max
Min Max
Min2
Max
Min Max
Interlaken core clock
412.503
479.20
412.503
479.20
N/A
412.50
429.69
N/A
MHz
Interlaken local bus clock
300.004
349.52
300.004
349.52
N/A
300.00
349.52
N/A
MHz
Notes:
1.
6 x 28.21 mode is only supported in the -2 (VCCINT = 0.85V) and -3 (VCCINT = 0.90V) speed grades.
2.
These are the minimum clock frequencies at the maximum lane performance.
3.
The minimum value for CORE_CLK is 451.36 MHz for the 6 x 28.21 Gb/s protocol.
4.
The minimum value for LBUS_CLK is 330.00 MHz for the 6 x 28.21 Gb/s protocol.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
63
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 75: Maximum Performance for Interlaken 12 x 25.78125 Gb/s Lane Logic Only Mode Designs
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
FRX_SERDES_CLK
Receive serializer/
deserializer clock
402.84
402.84
N/A
N/A
N/A
MHz
FTX_SERDES_CLK
Transmit serializer/
deserializer clock
402.84
402.84
N/A
N/A
N/A
MHz
FDRP_CLK
Dynamic reconfiguration port
clock
250.00
250.00
N/A
N/A
N/A
MHz
FCORE_CLK
Interlaken core clock
412.50
412.50
N/A
N/A
N/A
MHz
FLBUS_CLK
Interlaken local bus clock
349.52
349.52
N/A
N/A
N/A
MHz
Integrated Interface Block for 100G Ethernet MAC and
PCS
More information and documentation on solutions using the integrated 100 Gb/s Ethernet block can be found
at UltraScale+ Integrated 100G Ethernet MAC/PCS. The UltraScale Architecture and Product Data Sheet:
Overview (DS890) lists how many blocks are in each Kintex UltraScale+ FPGA.
Table 76: Maximum Performance for 100G Ethernet Designs
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
CAUI-10 Mode
FTX_CLK
Transmit clock
390.625
390.625
322.266
322.266
322.266
MHz
FRX_CLK
Receive clock
390.625
390.625
322.266
322.266
322.266
MHz
FRX_SERDES_CLK
Receive serializer/deserializer clock
390.625
390.625
322.266
322.266
322.266
MHz
FDRP_CLK
Dynamic reconfiguration port clock
250.00
250.00
250.00
250.00
250.00
MHz
CAUI-4, CAUI-4 + RS-FEC, and RS-FEC Transcode Bypass Modes
FTX_CLK
Transmit clock
390.625
322.266
322.266
322.266
N/A
MHz
FRX_CLK
Receive clock
390.625
322.266
322.266
322.266
N/A
MHz
FRX_SERDES_CLK
Receive serializer/deserializer clock
390.625
322.266
322.266
322.266
N/A
MHz
FDRP_CLK
Dynamic reconfiguration port clock
250.00
250.00
250.00
250.00
N/A
MHz
Integrated Interface Block for PCI Express Designs
More information and documentation on solutions for PCI Express® designs can be found at PCI Express. The
UltraScale Architecture and Product Data Sheet: Overview (DS890) lists how many blocks are in each Kintex
UltraScale+ FPGA.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
64
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 77: Maximum Performance for PCIE4-based PCI Express Designs
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
FPIPECLK
Pipe clock maximum frequency
250.00
250.00
250.00
250.00
250.00
MHz
FCORECLK
Core clock maximum frequency
500.00
500.00
500.00
250.00
250.00
MHz
FDRPCLK
DRP clock maximum frequency
250.00
250.00
250.00
250.00
250.00
MHz
FMCAPCLK
MCAP clock maximum frequency
125.00
125.00
125.00
125.00
125.00
MHz
The PCIE4C blocks in the XCKU19P include support for the CCIX protocol. Additional timing enhancements
allow the PCIE4C blocks to run Gen3 x16 in the -2LE speed grade when VCCINT = 0.72V.
Table 78: Maximum Performance for PCIE4C-based PCI Express and CCIX Designs
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
FPIPECLK
Pipe clock maximum frequency
250.00
250.00
250.00
250.00
250.00
MHz
FCORECLK
Core clock maximum frequency
500.00
500.00
500.00
500.00
250.00
MHz
FCORECLKCCIX
CCIX TL interface clock maximum
frequency
500.00
500.00
500.00
N/A
N/A
MHz
FDRPCLK
DRP clock maximum frequency
250.00
250.00
250.00
250.00
250.00
MHz
125.00
125.00
125.00
125.00
125.00
MHz
FMCAPCLK
MCAP clock maximum
frequency1
Notes:
1.
The XCKU19P device does not support tandem PCIe.
System Monitor Specifications
Table 79: System Monitor Specifications
Parameter
Symbol
Comments/Conditions
Min
Typ
Max
Units
10
–
–
Bits
–
–
±1.5
LSBs
No missing codes, guaranteed monotonic
–
–
±1
LSBs
Offset calibration enabled
VCCADC = 1.8V ±3%, VREFP = 1.25V, VREFN = 0V, ADCCLK = 5.2 MHz, Tj = –40°C to 100°C, typical values at Tj = 40°C
ADC Accuracy1
Resolution
Integral
nonlinearity2
Differential nonlinearity
INL
DNL
Offset error
–
–
±2
LSBs
Gain error
–
–
±0.4
%
Sample rate
–
–
0.2
MS/s
External 1.25V reference
–
–
1
LSBs
On-chip reference
–
1
–
LSBs
Tj = –55°C to 125°C
10
–
–
Bits
RMS code noise
ADC Accuracy at Extended Temperatures
Resolution
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
65
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 79: System Monitor Specifications (cont'd)
Parameter
Symbol
Comments/Conditions
Min
Typ
Max
Units
LSBs
Integral nonlinearity2
INL
Tj = –55°C to 125°C
–
–
±1.5
Differential nonlinearity
DNL
No missing codes, guaranteed monotonic
Tj = –55°C to 125°C
–
–
±1
Unipolar operation
0
–
1
V
–0.5
–
+0.5
V
0
–
+0.5
V
Analog Inputs2
ADC input ranges
Bipolar operation
Unipolar common mode range (FS input)
Maximum external channel input ranges
Bipolar common mode range (FS input)
+0.5
–
+0.6
V
Adjacent channels set within these ranges should
not corrupt measurements on adjacent channels
–0.1
–
VCCADC
V
Tj = –55°C to 125°C (with external REF)
–
–
±3
°C
Tj = –55°C to 110°C (with internal REF)
–
–
±3.5
°C
Tj = 110°C to 125°C (with internal REF)
–
–
±5
°C
Supply voltages 0.72V to 1.2V,
–
–
±0.5
%
–
–
±1.0
%
–
–
±1.0
%
–
–
±2.0
%
–
–
±1.0
%
–
–
±2.0
%
–
–
±1.5
%
–
–
±2.5
%
On-Chip Sensor Accuracy
Temperature sensor error1, 3
Supply sensor
error4
Tj = –40°C to 100°C (with external REF)
Supply voltages 0.72V to 1.2V,
Tj = –55°C to 125°C (with external REF)
All other supply voltages,
Tj = –40°C to 100°C (with external REF)
All other supply voltages,
Tj = –55°C to 125°C (with external REF)
Supply voltages 0.72V to 1.2V,
Tj = –40°C to 100°C (with internal REF)
Supply voltages 0.72V to 1.2V,
Tj = –55°C to 125°C (with internal REF)
All other supply voltages,
Tj = –40°C to 100°C (with internal REF)
All other supply voltages,
Tj = –55°C to 125°C (with internal REF)
Conversion Rate5
Conversion time—continuous
tCONV
Number of ADCCLK cycles
26
–
32
Cycles
Conversion time—event
tCONV
Number of ADCCLK cycles
–
–
21
Cycles
DRP clock frequency
DCLK
DRP clock frequency
8
–
250
MHz
ADC clock frequency
ADCCLK
Derived from DCLK
1
–
5.2
MHz
40
–
60
%
1.20
1.25
1.30
V
DCLK duty cycle
SYSMON Reference6
External reference
VREFP
DS922 (v1.17) February 16, 2021
Product Specification
Externally supplied reference voltage
Send Feedback
www.xilinx.com
66
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 79: System Monitor Specifications (cont'd)
Parameter
Symbol
On-chip reference
Comments/Conditions
Min
Typ
Max
Units
Ground VREFP pin to AGND, Tj = –40°C to 100°C
1.2375
1.25
1.2625
V
Ground VREFP pin to AGND, Tj = –55°C to 125°C
1.225
1.25
1.275
V
Notes:
1.
ADC offset errors are removed by enabling the ADC automatic offset calibration feature. The values are specified for when this feature is
enabled.
2.
See the Analog Input section in the UltraScale Architecture System Monitor User Guide (UG580).
3.
When reading temperature values directly from the PMBus interface, the SYSMON has a +4°C offset due to the transfer function used by
the PMBus application. For example, the external REF temperature sensor error’s range of ±3°C becomes +1°C to +7°C when the
temperature is read through the PMBus interface.
4.
Supply sensor offset and gain errors are removed by enabling the automatic offset and gain calibration feature. The values are specified
for when this feature is enabled.
5.
See the Adjusting the Acquisition Settling Time section in the UltraScale Architecture System Monitor User Guide (UG580).
6.
Any variation in the reference voltage from the nominal VREFP = 1.25V and VREFN = 0V will result in a deviation from the ideal transfer
function. This also impacts the accuracy of the internal sensor measurements (i.e., temperature and power supply). However, for
external ratiometric type applications allowing reference to vary by ±4% is permitted.
SYSMON I2C/PMBus Interfaces
Table 80: SYSMON I2C Fast Mode Interface Switching Characteristics
Description1
Symbol
Min
Max
Units
TSMFCKL
SCL Low time
1.3
–
µs
TSMFCKH
SCL High time
0.6
–
µs
TSMFCKO
SDAO clock-to-out delay
–
900
ns
TSMFDCK
SDAI setup time
100
–
ns
FSMFCLK
SCL clock frequency
–
400
kHz
Min
Max
Units
–
µs
Notes:
1.
The test conditions are configured to the LVCMOS 1.8V I/O standard.
Table 81: SYSMON I2C Standard Mode Interface Switching Characteristics
Description1
Symbol
TSMSCKL
SCL Low time
4.7
4.0
–
µs
–
3450
ns
250
–
ns
–
100
kHz
TSMSCKH
SCL High time
TSMSCKO
SDAO clock-to-out delay
TSMSDCK
SDAI setup time
FSMSCLK
SCL clock frequency
Notes:
1.
The test conditions are configured to the LVCMOS 1.8V I/O standard.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
67
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Configuration Switching Characteristics
Table 82: Configuration Switching Characteristics
Speed Grade and VCCINT Operating Voltages
Symbol
Description
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
XCKU19P
8.5
8.5
8.5
8.5
8.5
All other devices
7.5
7.5
7.5
7.5
7.5
ms, Max
65
65
65
65
65
ms, Max
0
0
0
0
0
ms, Min
Power-on reset with POR override (2 ms
maximum ramp rate)
15
15
15
15
15
ms, Max
5
5
5
5
5
ms, Min
Program pulse width
250
250
250
250
250
ns, Min
Master CCLK output delay from INIT_B
150
150
150
150
150
ns, Min
TMCCKL
Master CCLK clock Low time duty cycle
40/60
40/60
40/60
40/60
40/60
%, Min/Max
TMCCKH
Master CCLK clock High time duty cycle
40/60
40/60
40/60
40/60
40/60
%, Min/Max
FMCCK
Master SPI (x1/x2/x4)
CCLK frequency
XCKU3P, XCKU5P,
XQKU5P
125
125
125
60
60
MHz, Max
XCKU19P
125
125
125
100
100
Power-up Timing Characteristics
TPL
Program latency
TPOR
Power-on reset (40 ms maximum ramp rate)
TPROGRAM
ms, Max
CCLK Output (Master Mode)
TICCK
1
Master SPI (x8) or
Master BPI (x8/x16)2
CCLK frequency
All other devices
150
150
150
125
125
XCKU3P, XCKU5P,
XQKU5P
125
125
125
60
60
XCKU19P
100
100
100
60
60
All other devices
150
150
150
125
125
FMCCK_START
Master CCLK frequency at start of
configuration
2.70
2.70
2.70
2.70
2.70
MHz, Typ
FMCCKTOL
Frequency tolerance, master mode with
respect to nominal CCLK
±15
±15
±15
±15
±15
%, Max
CCLK Input (Slave Mode)
TSCCKL
Slave CCLK clock minimum Low time
2.5
2.5
2.5
2.5
2.5
ns, Min
TSCCKH
Slave CCLK clock minimum High time
2.5
2.5
2.5
2.5
2.5
ns, Min
FSCCK
Slave serial CCLK
frequency
XCKU3P, XCKU5P,
XQKU5P
125
125
125
60
60
MHz, Max
XCKU19P
125
125
125
100
100
Slave SelectMAP CCLK
frequency
All other devices
125
125
125
125
125
XCKU3P, XCKU5P,
XQKU5P
125
125
125
60
60
XCKU19P
100
100
100
60
60
All other devices
125
125
125
125
125
EMCCLK Input (Master Mode)
TEMCCKL
External master CCLK Low time
2.5
2.5
2.5
2.5
2.5
ns, Min
TEMCCKH
External master CCLK High time
2.5
2.5
2.5
2.5
2.5
ns, Min
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
68
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 82: Configuration Switching Characteristics (cont'd)
Speed Grade and VCCINT Operating Voltages
Symbol
FEMCCK
Description
External master CCLK
frequency with Master
SPI x1/x2/x4
External master CCLK
frequency with Master
SPI x8 or Master BPI
x8/x162
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
XCKU3P, XCKU5P,
XQKU5P
125
125
125
60
60
XCKU19P
125
125
125
100
100
MHz, Max
All other devices
150
150
150
125
125
XCKU3P, XCKU5P,
XQKU5P
125
125
125
60
60
XCKU19P
100
100
100
60
60
All other devices
150
150
150
125
125
200
200
200
150
150
MHz, Max
3.0/0
3.0/0
3.0/0
4.0/0
4.0/0
ns, Min
8.0
8.0
8.0
9.0
9.0
ns, Max
XCKU3P, XCKU5P,
XQKU5P
4.5/0
4.5/0
4.5/0
8.0/0
8.0/0
ns, Min
XCKU19P
5.5/0
5.5/0
5.5/0
8.5/0
8.5/0
All other devices
3.5/0
3.5/0
3.5/0
4.5/0
4.5/0
XCKU3P, XCKU5P,
XQKU5P
4.5/0
4.5/0
4.5/0
7.0/0
7.0/0
XCKU19P
5.0/0
5.0/0
5.0/0
8.5/0
8.5/0
All other devices
4.0/0
4.0/0
4.0/0
5.0/0
5.0/0
XCKU3P, XCKU5P,
XQKU5P
10.0/0
10.0/0
10.0/0
17.0/0
17.0/0
XCKU19P
11.0/0
11.0/0
11.0/0
17.5/0
17.5/0
All other devices
10.0/0
10.0/0
10.0/0
11.0/0
11.0/0
XCKU3P, XCKU5P,
XQKU5P
7.0
7.0
7.0
10.0
10.0
XCKU19P
7.0
7.0
7.0
10.0
10.0
All other devices
7.0
7.0
7.0
7.0
7.0
XCKU3P, XCKU5P,
XQKU5P
8.0
8.0
8.0
10.0
10.0
XCKU19P
8.0
8.0
8.0
10.0
10.0
Internal Configuration Access Port
FICAPCK
Internal configuration access port (ICAPE3)
Slave Serial Mode Programming Switching
TDCCK/TCCKD
DIN setup/hold
TCCO
DOUT clock to out
SelectMAP Mode Programming Switching
TSMDCCK/TSMCCKD
TSMCSCCK/TSMCCKCS
TSMWCCK/TSMCCKW
TSMCKCSO
TSMCO
FRBCCK
D[31:00] setup/hold
CSI_B setup/hold
RDWR_B setup/hold
CSO_B clock to out
(330Ω pull-up resistor
required)
D[31:00] clock to out in
readback
Readback frequency
ns, Min
ns, Min
ns, Max
ns, Max
All other devices
8.0
8.0
8.0
8.0
8.0
XCKU3P, XCKU5P,
XQKU5P
125
125
125
60
60
XCKU19P
100
100
100
60
60
All other devices
125
125
125
125
125
3.0/2.0
3.0/2.0
3.0/2.0
3.0/2.0
3.0/2.0
ns, Min
7.0
7.0
7.0
7.0
7.0
ns, Max
MHz, Max
Boundary-Scan Port Timing Specifications
TTAPTCK/TTCKTAP
TMS and TDI setup/hold
TTCKTDO
TCK falling edge to TDO output
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
69
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 82: Configuration Switching Characteristics (cont'd)
Speed Grade and VCCINT Operating Voltages
Symbol
FTCK
Description
TCK frequency
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
XCKU15P,
XQKU15P,
XCKU19P
66
66
66
50
50
All other devices
66
66
66
66
66
10
10
10
10
10
ns, Max
XCKU3P, XCKU5P,
XQKU5P
4.5/0
4.5/0
4.5/0
8.0/0
8.0/0
ns, Min
XCKU19P
5.5/0
5.5/0
5.5/0
8.5/0
8.5/0
All other devices
3.5/0
3.5/0
3.5/0
4.5/0
4.5/0
3.0/0
3.0/0
3.0/0
4.0/0
4.0/0
ns, Min
XCKU3P, XCKU5P,
XQKU5P
4.5/0
4.5/0
4.5/0
8.0/0
8.0/0
ns, Min
XCKU19P
5.5/0
5.5/0
5.5/0
8.5/0
8.5/0
All other devices
3.5/0
3.5/0
3.5/0
4.5/0
4.5/0
MHz, Max
BPI Master Flash Mode Programming Switching
TBPICCO
A[28:00], RS[1:0], FCS_B, FOE_B, FWE_B,
ADV_B clock to out
TBPIDCC/TBPICCD
D[15:00] setup/hold
SPI Master Flash Mode Programming Switching
TSPIDCC/TSPICCD
D[03:00] setup/hold
TSPIDCC/TSPICCD
D[07:04] setup/hold
TSPICCM
MOSI clock to out
8.0
8.0
8.0
8.0
8.0
ns, Max
TSPICCM2
D[04] clock to out
10.0
10.0
10.0
10.0
10.0
ns, Max
TSPICCFC
FCS_B clock to out
8.0
8.0
8.0
8.0
8.0
ns, Max
TSPICCFC2
FCS2_B clock to out
10.0
10.0
10.0
10.0
10.0
ns, Max
DNA port frequency
200
200
200
175
175
MHz, Max
DNA Port Switching
FDNACK
STARTUPE3 Ports
TUSRCCLKO
STARTUPE3 USRCCLKO input port to CCLK
pin output delay
0.25/6.00 0.25/6.50
0.25/7.50
0.25/9.00
0.25/9.00
ns, Min/Max
TDO
DO[3:0] ports to D03-D00 pins output delay
0.25/6.70 0.25/7.70
0.25/8.40
0.25/10.00
0.25/10.00
ns, Min/Max
TDTS
DTS[3:0] ports to D03-D00 pins 3-state delays 0.25/6.70 0.25/7.70
0.25/8.40
0.25/10.00
0.25/10.00
ns, Min/Max
TFCSBO
FCSBO port to FCS_B pin output delay
0.25/6.90 0.25/7.50
0.25/8.40
0.25/9.80
0.25/9.80
ns, Min/Max
TFCSBTS
FCSBTS port to FCS_B pin 3-state delay
0.25/6.90 0.25/7.50
0.25/8.40
0.25/9.80
0.25/9.80
ns, Min/Max
TUSRDONEO
USRDONEO port to DONE pin output delay
0.25/8.60 0.25/9.40
0.25/10.50
0.25/12.10
0.25/12.10
ns, Min/Max
TUSRDONETS
USRDONETS port to DONE pin 3-state delay
0.25/8.60 0.25/9.40
0.25/10.50
0.25/12.10
0.25/12.10
ns, Min/Max
TDI
D03-D00 pins to DI[3:0] ports input delay
0.5/2.6
0.5/3.1
0.5/3.5
0.5/4.0
0.5/4.0
ns, Min/Max
FCFGMCLK
STARTUPE3 CFGMCLK output frequency
50
50
50
50
50
MHz, Typ
FCFGMCLKTOL
STARTUPE3 CFGMCLK output frequency
tolerance
±15
±15
±15
±15
±15
%, Max
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
70
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Table 82: Configuration Switching Characteristics (cont'd)
Speed Grade and VCCINT Operating Voltages
Symbol
TDCI_MATCH
Description
Specifies a stall in the startup cycle until the
digitally controlled impedance (DCI) match
signals are asserted
0.90V
0.85V
0.72V
Units
-3
-2
-1
-2
-1
4
4
4
4
4
ms, Max
Notes:
1.
When the CCLK is sourced from the EMCCLK pin with a divide-by-one setting, the external EMCCLK must meet this duty-cycle
requirement.
2.
SPI mode is recommended for master mode configuration from flash memory because of the higher configuration rates and low
configuration interface pin counts. Due to the obsolescence of synchronous read-mode flash devices, BPI mode performance is limited.
For system configuration rates with SPI flash and parallel NOR flash in BPI asynchronous read mode see the UltraScale Architecture
Configuration User Guide (UG570).
Revision History
Date
Version
2/16/2021
1.17
Description of Revisions
Updated Table 20, Table 21, and Table 22 to production release the XCKU19P devices in Vivado Design
Suite 2020.2.2 v1.32.
Revised some of the XCKU19P speed files in Table 40, Table 41, Table 42, Table 44, and Table 45.
For the KU19P device only, added PCIE4C support in Table 78.
12/08/2020
1.16
Added the XCKU19P device to Table 20, Table 21, and Table 22 in Vivado Design Suite 2020.2 v1.04, and
where applicable in other sections of this data sheet.
Added Note 10 to Table 12.
Updated the Table 25: MIPI D-PHY Performance table with Vivado tools specific conditions.
Increased the maximum line rate of the QPLL0 -1 (VCCINT = 0.85V) output divider 1 in Table 64 and
updated Notes 3 and 4.
Added Note 2 to the Configuration Switching Characteristics table.
7/12/2019
1.15
Added Note 7 to Table 10. Added the capability for XC devices designed using Vivado Design Suite
v2019.1.1 or later to increase the performance of the MIPI PHY transmitter/receiver in Table 25.
4/09/2019
1.14
Added the XQKU5P and XQKU15P devices in -1M temperature grade throughout this version including
updates to Table 20, Table 21, and Table 22 in Vivado Design Suite 2018.3.1 v1.23. This version also added
the ruggedized FFRB676, SFRB784, FFRA1156, and FFRE1517 packages.
Added LVDS component mode notes to FPGA Logic Performance Characteristics.
Removed PCI Express Gen4 support in Integrated Interface Block for PCI Express Designs and Note 1,
Note 2, and Note 3.
8/01/2018
1.13
Updated Table 20, Table 21, and Table 22 to production release the XCKU9P devices in the -3E speed/
temperature grade in Vivado Design Suite 2018.2.1 v1.21.
In Table 24, added Note 4 to the LVDS RX DDR maximum data.
In Table 76, revised the calculated values from 322.223 to 322.266.
6/18/2018
1.12
Revised the speed grade -1 (VCCINT = 0.85) FGTYMAX in Table 64, which also revised values in Table 69 and
added Note 6.
4/09/2018
1.11
Updated Table 20, Table 21, and Table 22 to production release the XCKU3P, XCKU5P, XCKU11P,
XCKU13P, and XCKU15P devices in the -3E speed/temperature grade in Vivado Design Suite 2018.1 v1.19.
Added Table 43 and Table 47. Added Note 2 and 3 to Table 46.
Revised Table 76 to add specific mode specifications and remove Notes 1 and 2.
2/07/2018
1.10
Updated Table 20, Table 21, and Table 22 to production release the XCKU11P with -2LE and -1LI speed/
temperature grades in Vivado Design Suite 2017.4.1.
Revised some of the -3E and -1LI/-2LE (VCCINT = 0.72V) speed files in Table 28, Table 40, Table 41, Table 42,
Table 44, and Table 45.
12/22/2017
1.9
Revised Table 21 and Table 22 to production release the XCKU15P -1L, -2L, -1LV, and -2LV speed/
temperature grades in Vivado Design Suite 2017.4.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
71
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Date
Version
Description of Revisions
11/28/2017
1.8
Updated Table 20, Table 21, and Table 22 to production release the following devices/speed/temperature
grades in Vivado Design Suite 2017.4.
XCKU3P: -2LE, -1LI
XCKU5P: -2LE, -1LI
Revised the FREFCLK descriptions in Table 35. Revised the FGTYQRANGE2 -1 speed grade minimum in Table
64. Added TSPICCM2 and TSPICCFC2 to Table 82.
11/17/2017
1.7
In Table 1, corrected the minimum voltage for the System Monitor section.
Updated Table 20, Table 21, and Table 22 to production release the following devices/speed/temperature
grades in Vivado Design Suite 2017.3.1.
XCKU9P: -2LE, -1LI
XCKU13P: -2LE, -1LI
Updated speed file data for this release in Table 40, Table 41, Table 42, and Table 44. Updated the notes
for FGTYMAX in Table 64.
10/05/2017
1.6
In Table 1, because the voltages are covered in Table 4, removed the note on VIN for I/O input voltage for
HD I/O banks. Updated TSOL by package in Table 1. Added Note 2 to Table 4.
Updated Table 20, Table 21, and Table 22 the XCKU11P: -2E, -2I, -1E, -1I (all VCCINT = 0.85V) to production
in Vivado Design Suite 2017.3 v1.14. Also updated speed file data for this release in Table 40, Table 41,
Table 42, Table 44, and Table 45.
8/29/2017
1.5
Updated Table 20, Table 21, and Table 22 to production release the following devices/speed/temperature
grades in Vivado Design Suite 2017.2.1.
XCKU15P: -2E, -2I, -1E, -1I (all VCCINT = 0.85V)
In Table 29, revised the TOUTBUF_DELAY_O_PAD -2 (VCCINT = 0.85V) values for DIFF_SSTL135_S,
DIFF_SSTL15_DCI_S, DIFF_SSTL15_S, DIFF_SSTL18_I_DCI_S, and DIFF_SSTL18_I_S.
Revised some of the -3E and -1LI/-2LE (VCCINT = 0.72V) speed files in Table 28, Table 29, Table 30, Table 40,
Table 41, Table 42, Table 44, and Table 45.
6/26/2017
1.4
Updated Table 20, Table 21, and Table 22 to production release the following devices/speed/temperature
grades in Vivado Design Suite 2017.2.
XCKU13P: -2E, -2I, -1E, -1I (all VCCINT = 0.85V)
Updated Note 11 in Table 2 for clarity. Revised the -3E and -1LI/-2LE (VCCINT = 0.72V) speed files in Table
28, Table 29, Table 30, Table 40, Table 41, Table 42, Table 44, and Table 45. Updated the FMAX symbol
names and values in Table 34. Added Note 1 to Table 36. Added Note 3 to Table 77.
5/08/2017
1.3
Updated Table 21 and Table 22 to production release the following devices/speed/temperature grades in
Vivado Design Suite 2017.1.
XCKU9P: -2E, -2I, -1E, -1I
Removed the MIPI_DPHY_DCI_LP standard from Table 9 (HD I/O banks never supported DCI). Revised
the minimum 32.75 Gb/s sinusoidal jitter in Table 71.
4/11/2017
1.2
Updated the Summary description. In Table 1, updated and added data, and updated Note 6, added
Note 7, Note 8, and Note 9. Updated and added data to Table 2, revised Note 11 and added Note 12 and
Note 13. Updated Table 3 and added Note 6. Added specifications to Table 4 though Table 6. Updated
maximum VICM and Note 1 in Table 18. Updated the maximum VODIFF in Table 19.
Updated Table 20, Table 21, and Table 22 to production release the following devices/speed/temperature
grades in Vivado Design Suite 2017.1.
XCKU3P: -2E, -2I, -1E, -1I
XCKU5P: -2E, -2I, -1E, -1I
Added Note 1 to Table 21. Updated Table 23. Updated Table 24 and added Note 2. Added Table 25.
Updated Table 27 and added Note 3. Many revisions to the speed specifications in Table 28, Table 29,
Table 30, Table 33, Table 34, Table 35, Table 40, Table 41, Table 42, Table 44, Table 45, and Table 46.
Updated VL and VH values in Table 31. In Table 35, added TMINPER_CLK and Note 1, and revised FREFCLK.
Added MMCM_FDPRCLK_MAX to Table 38 and PLL_FDPRCLK_MAX to Table 39. Updated Table 48. Revised the
GTH Transceiver Specifications and GTY Transceiver Specifications sections. Revised the Integrated
Interface Block for Interlaken and Integrated Interface Block for 100G Ethernet MAC and PCS sections.
Updated the System Monitor Specifications section including On-Chip Sensor Accuracy and adding Note
3 to Table 79. Removed timing diagrams from the SYSMON I2C/PMBus Interfaces section. Updated the
Configuration Switching Characteristics section. Removed the eFUSE Programming Conditions table and
added the specifications to Table 2 and Table 3. Updated Table 82. Updated the Automotive Applications
Disclaimer.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
72
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Date
Version
Description of Revisions
5/09/2016
1.1
In Table 1 revised VIN for HP I/O banks. Updated Note 5 in Table 3. Added values to Table 7. Added
MIPI_DPHY_DCI to Table 9, Table 10, and Table 12. Updated and added notes in Table 18 and Table 19.
Updated Table 20 speed specifications for Vivado Design Suite 2016.1. Removed Table 23, Video Codec
Unit Performance. Updated Table 24. Expanded and updated Table 27. Updated Table 28 and Table 29.
Updated Table 31 and Table 32 with MIPI D-PHY values. Updated Table 31 and Table 32. In Table 33,
added the Block RAM and FIFO Clock-to-Out Delays section. Updated Table 40 to Table 45. Revised the
symbol names in Table 44. Revised typical values in Table 50. Updated the -2 (0.72V) and -1 (0.72V) values
in Table 52. Added Table 55 and Table 67. Added Note 2 to Table 61. Revised Table 69. Revised data and
added notes to Table 64, Table 73, and Table 76. Revised INL in Table 79. Added notes to Table 80 and
Table 81. Many revised sections in Table 82.
11/24/2015
1.0
Initial Xilinx release.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
73
Kintex UltraScale+ FPGAs Data Sheet: DC and AC Switching Characteristics
Please Read: Important Legal Notices
The information disclosed to you hereunder (the "Materials") is provided solely for the selection and use of
Xilinx products. To the maximum extent permitted by applicable law: (1) Materials are made available "AS IS" and
with all faults, Xilinx hereby DISCLAIMS ALL WARRANTIES AND CONDITIONS, EXPRESS, IMPLIED, OR
STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NONINFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and (2) Xilinx shall not be liable (whether in
contract or tort, including negligence, or under any other theory of liability) for any loss or damage of any kind
or nature related to, arising under, or in connection with, the Materials (including your use of the Materials),
including for any direct, indirect, special, incidental, or consequential loss or damage (including loss of data,
profits, goodwill, or any type of loss or damage suffered as a result of any action brought by a third party) even if
such damage or loss was reasonably foreseeable or Xilinx had been advised of the possibility of the same. Xilinx
assumes no obligation to correct any errors contained in the Materials or to notify you of updates to the
Materials or to product specifications. You may not reproduce, modify, distribute, or publicly display the
Materials without prior written consent. Certain products are subject to the terms and conditions of Xilinx's
limited warranty, please refer to Xilinx's Terms of Sale which can be viewed at https://www.xilinx.com/
legal.htm#tos; IP cores may be subject to warranty and support terms contained in a license issued to you by
Xilinx. Xilinx products are not designed or intended to be fail-safe or for use in any application requiring fail-safe
performance; you assume sole risk and liability for use of Xilinx products in such critical applications, please
refer to Xilinx's Terms of Sale which can be viewed at https://www.xilinx.com/legal.htm#tos.
AUTOMOTIVE APPLICATIONS DISCLAIMER
AUTOMOTIVE PRODUCTS (IDENTIFIED AS "XA" IN THE PART NUMBER) ARE NOT WARRANTED FOR USE
IN THE DEPLOYMENT OF AIRBAGS OR FOR USE IN APPLICATIONS THAT AFFECT CONTROL OF A
VEHICLE ("SAFETY APPLICATION") UNLESS THERE IS A SAFETY CONCEPT OR REDUNDANCY FEATURE
CONSISTENT WITH THE ISO 26262 AUTOMOTIVE SAFETY STANDARD ("SAFETY DESIGN"). CUSTOMER
SHALL, PRIOR TO USING OR DISTRIBUTING ANY SYSTEMS THAT INCORPORATE PRODUCTS,
THOROUGHLY TEST SUCH SYSTEMS FOR SAFETY PURPOSES. USE OF PRODUCTS IN A SAFETY
APPLICATION WITHOUT A SAFETY DESIGN IS FULLY AT THE RISK OF CUSTOMER, SUBJECT ONLY TO
APPLICABLE LAWS AND REGULATIONS GOVERNING LIMITATIONS ON PRODUCT LIABILITY.
DS922 (v1.17) February 16, 2021
Product Specification
Send Feedback
www.xilinx.com
74