ASB110PS36

ASB110 Series AC-DC Power Supplies XP Power 110 Watts • Complete AC/DC Power Supply • No Extra Components Required • Base Plate Cooled • -40 to +85 °C Base Plate Temperature • Low Profile in Full Brick Package • High Efficiency - Up to 91% • Universal Input • 0.9 115 VAC/Measured at 230 VAC 230 VAC, cold start at 25 °C Full load 264 VAC, 60 Hz Internal T3.15A/250 VAC fitted in line General Characteristic Minimum Efficiency Typical 90 % 3000 Isolation: Input to Output Input to Ground Output to Ground Switching Frequency Power Density Mean Time Between Failure Weight 1 See Models and Ratings table VAC 1500 VAC 500 VDC 70-130 / 50-90 kHz 14.8 W/in3 0.51 (230) lb (g) 160 Notes & Conditions kHrs www.xppower.com PFC / PWM MIL-HDBK-217F at 25 °C GB ASB110 Series AC-DC Power Supplies XP Power Output Characteristic Min. Output Voltage 12 Typ. Initial Set Accuracy Max. Units Notes & Conditions 48 VDC See Models and Ratings table 1 % At 60% load Minimum Load No minimum load required Start Up Delay Start Up Rise Time Hold Up Time 1.3 s 20 ms 10 ms Line Regulation ±0.5 % Load Regulation ±0.5 % Transient Response 2 % Ripple and Noise 1 % pk-pk Overload Protection 130 210 % Overvoltage Protection 110 140 % Short Circuit Protection Trip and restart (hiccup), auto resetting Thermal Protection Measured internally, auto resetting Temperature Coefficient 0.02 Full load and 115 VAC Maximum deviation, recovering to less than 1% within 300 μs for 25% step load 20 MHz bandwidth, measured with 20 MHz Bandwidth and 10 μF electrolytic in parallel with 0.1 μF ceramic capacitor. Recycle mains to reset %/°C Environmental Characteristic Operating Temperature Cooling Minimum Typical -40 Maximum Units +85 °C Notes & Conditions Baseplate Temperature, see derating curve Conduction Cooled via Baseplate Operating Humidity 5 90 %RH Storage Temperature -40 +85 °C 5000 m Operating Altitude Non-condensing Shock IEC68-2-27, 30 g, 11 ms half sine, 3 times in each of 6 axes Vibration IEC68-2-6, 10-500 Hz, 2 g 10 mins/sweep, 60 mins for each of 3 axes EMC: Emissions Phenomenon Standard Test Level Emissions EN55032 Level B Harmonic Current EN61000-3-2 Class A Voltage Flicker EN61000-3-3 Notes & Conditions EMC: Immunity Test Level Criteria ESD Phenomenon EN61000-4-2 3/2 A Radiated EN61000-4-3 3 V/m A EFT/Burst EN61000-4-4 3 A Surge EN61000-4-5 Installation Class 3 A Conducted EN61000-4-6 3V A Dips and Interruptions Standard EN61000-4-11 Dip: 100% 10 ms A Dip: 30% 500 ms A/B Int:100% 5000 ms B Notes & Conditions ±8 kV air/±4 kV contact High Line/Low Line Safety Approvals Safety Agency Safety Standard UL UL60950-1, UL62368-1 TUV EN60950-1, EN62368-1 CB Notes & Conditions IEC60950-1, IEC62368-1 CE Meets all applicable directives UKCA Meets all applicable legislation www.xppower.com 2 ASB110 Series AC-DC Power Supplies XP Power Mechanical Details 5-Ø 0.08 (2.0) 0.40 (10.16) ACL 2.00 (50.8) +Vout ACN -Vout 4 mounting holes, 3.5 mm 0.30 (7.6) FG 0.40 (10.16) 0.30 (7.6) 2.40 (61.0) 4.20 (106.7) 0.23 (5.9) 4.60 (116.8) 0.67 (17.0) 1.00 (25.4) Optional Heatsink (IFH HEATSINK) 4.20 (106.7) 2.40 (61.0) 4.60 (116.8) Notes 1. Dimensions shown in inches (mm). 2. Weight: 0.51 lb (230 g) 3. Pin diameter: 0.08 ±0.002 (2.0 ±0.05) 4. Pin pitch tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) 6. Baseplate is connected to FG Pin Application Notes Derating Curve 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 50 Some specification parameters may not be met Load (%) 50 100 With IFH HEATSINK Some specification parameters may not be met Load (%) 100 0 -40 -30 Ambient Temperature (°C) -20 -10 0 10 20 30 40 50 60 70 80 90 Baseplate Temperature (°C) Notes When ASB110 is fitted with IFH HEATSINK and mounted in horizontal position with heatsink upper most, the base plate temperature will typically be 85 °C in an ambient of 50 °C. www.xppower.com 3 ASB110 Series AC-DC Power Supplies XP Power Application Notes Efficiency Curves ASB110PS12 100% 90% 85Vac input Efficiency 90Vac input 115Vac input 80% 230Vac input 264Vac input 70% 60% 10 20 30 40 50 60 70 80 90 100 Load (%) ASB110PS24 100% 90% Efficiency 85Vac input 90Vac input 115Vac input 80% 230Vac input 264Vac input 70% 60% 10 20 30 40 50 60 70 80 90 100 Load (%) Lifetime Lifetime 400 350 300 KHrs 250 200 150 100 50 25 85 75 65 55 45 Baseplate Temperature (°C) www.xppower.com 26 August 2021