CPL150PD12

AC-DC Open Frame 100-225 Watts CPL Series • THE XPERTS IN POWER Isolated Outputs • High Peak Current Ratings • Compact PCB Construction • Optional Remote On/Off • Adjustable Output Voltage • EN55022 Level B • Cover, Connector & Loom Kits Available Specification Input Input Voltage Input Frequency Inrush Current Power Factor Earth Leakage Current • • • • • 85-264 VAC (120-370 VDC) 47-63 Hz 15/30 A at 120/230 VAC in, 100% load & 25 °C 0.99 typical at 100 VAC, 0.93 typical at 200 VAC & 100% load to IEC61000-3-2 0.75 mA max at 230 VAC 60 Hz Options • Designated by the following suffixes to the model number: Reduce leakage current 105% of rated current on V1 & >101% of peak current on V2 auto recovery >115% of nominal value for V1 & 115-140% of nominal value for V2 74-83% depending on specific model 3000 VAC Input to Output 2000 VAC Input to Ground 500 VAC Output to Ground V1 to V2 100 VAC 1 min, cut off current 100 mA, 100 VDC 10 MΩ min 80-500 kHz Environmental Operating Temperature Storage Temperature Humidity Shock Vibration • • • • • -10 °C to +70 °C (See Derating Curve) -20 °C to +75 °C 20-90% RH, non condensing 196.1 m/s2 (20 G), 11 ms once each X, Y & Z axis 2 G 10-55 Hz, 3 axis EMC & Safety Emissions ESD Susceptibility Radiated Susceptibility EFT/Burst Surge Safety Approvals • • • • • • EN55022 Level B conducted EN55022 Level B radiated EN61000-4-2 Level 2 contact Level 3 air EN61000-4-3 Level 3 EN61000-4-4 Level 3 EN61000-4-5 Level 3 line to line Level 4 line to ground UL1950, C-UL, EN60950, VDE0160 General Efficiency Isolation • • Switching Frequency • • • www.xpplc.com sales@xpplc.com OUTPUT VOLTAGE & CURRENT RATINGS - 100 WATT MODEL Output Voltage +5 V1 +24 V2 +5 V1 +12 V2 Current Rating Maximum Peak(1) 5.0 A 4.0 A 7A 5.0 A 5.0 A 10 A Regulation Line Load 20 mV 40 mV 96 mV 150 mV 20 mV 40 mV 48 mV 100 mV Ripple & Noise pk-pk(2) 120 mV 150 mV 120 mV 150 mV Efficiency(3) Typical 80% 76% Model Number CPL CPL100PD24 CPL100PD12 • Notes 1. Peak rating for 10 sec with a duty cycle of 35% max. 2. Measured with 22µF cap within 150 mm of output terminal at 20 MHz bandwidth. 3. Measured at 200 VAC input & 100% load. Mechanical Details - 100 Watt Models I/O Connector CN1 CN2 B3P5-VH B8P-VH Mating Connector VHR-5N VHR-8N XHP-2 XHP-3 CN3 B2B-XH-A (Option) CN4 B3B-XH-A (Option) Terminal Chain: SVH-21T-P1.1 Loose: 8VH-21T-P1.1 Chain: SVH-21T-P1.1 Loose: 8VH-21T-P1.1 Chain: SXH-001-P0.6 Loose: BXH-001T-P0.6 Chain: SXH-001-P0.6 Loose: BXH-001T-P0.6 Pin No. 1 2 3 4 5 CN1 Input AC(L) AC(N) FG Pin No. 1, 2 3, 4 5, 6 7, 8 CN2 Output G2 V2 G1 V1 CN3 (Optional) Pin No. Remote On/Off 1 RC(+) 2 RC(-) CN4 (Optional) Pin No. ‘-Z’ 1 + 2 COM 3 - NOTES: • Weight 420g or less (without chassis & cover). • Tolerance ±1. • Dimensions in mm. • PCB Material : CEM3. • Optional chassis & cover, order part no. CPL100 COVER or add suffix ‘-C’ to the model number to receive the unit with the cover fitted. • Mounting torque 1.5N m (16 kgf cm) max. • Keep drawing current per pin below 5 A (7 A @ pk load) for CN2. • Optional connector kit available, order part no. CPL100/150 CON. • Optional loom kit available, order part no. CPL100/150 LOOM. Derating Curves - 100 Watt Models OPEN FRAME COVER FITTED (>90 VAC INPUT) www.xpplc.com sales@xpplc.com OUTPUT VOLTAGE & CURRENT RATINGS - 150 WATT MODEL Output Voltage +5 V 1 +24 V 2 +5 V 1 +12 V 2 Notes 1. Peak rating for 10 sec with a duty cycle of 35% max. 2. Measured with 22 µF cap within 150 mm of output terminal at 20 MHz bandwidth. 3. Measured at 200 V AC input & 100% load. CPL Efficiency(3) Typical 82% 79% Model Number CPL150PD24 CPL150PD12 Current Rating Maximum Peak(1) 5.0 A 6.0 A 10 A 5.0 A 7.5 A 14 A Regulation Line Load 20 mV 40 mV 96 mV 150 mV 20 mV 40 mV 48 mV 100 mV Ripple & Noise pk-pk(2) 120 mV 150 mV 120 mV 150 mV • Mechanical Details - 150 Watt Models I/O Connector CN1 CN2 B3P5-VH B8P-VH Mating Connector VHR-5N VHR-8N XHP-2 XHP-3 CN3 B2B-XH-A (Option) CN4 B3B-XH-A (Option) Terminal Chain: SVH-21T-P1.1 Loose: 8VH-21T-P1.1 Chain: SVH-21T-P1.1 Loose: 8VH-21T-P1.1 Chain: SXH-001-P0.6 Loose: BXH-001T-P0.6 Chain: SXH-001-P0.6 Loose: BXH-001T-P0.6 CN1 Pin No. 1 2 3 4 5 Input AC(L) AC(N) FG Pin No. 1, 2 3, 4 5, 6 7, 8 CN2 Output G2 V2 G1 V1 NOTES: • Weight 530g or less (without chassis & cover). • Tolerance ±1. • Dimensions in mm. • PCB Material : CEM3. • Optional chassis & cover, order part no. CPL150 COVER or add suffix ‘-C’ to the model number to receive the unit with the cover fitted. • Mounting torque 1.5N m (16 kgf cm) max. • Ensure current per pin is below 5 A (7 A @ pk load) for CN2. • Optional connector kit available, order part no. CPL100/150 CON. • Optional loom kit available, order part no. CPL100/150 LOOM. CN3 (Optional) Pin No. Remote On/Off 1 RC(+) 2 RC(-) CN4 (Optional) Pin No. ‘-Z’ 1 + 2 COM 3 - Derating Curves - 150 Watt Models OPEN FRAME COVER FITTED (>90 VAC INPUT) www.xpplc.com sales@xpplc.com OUTPUT VOLTAGE & CURRENT RATINGS - 225 WATT MODEL Output Voltage +5 V1 +24 V2 +5 V1 +12 V2 Notes 1. Peak rating for 10 sec with a duty cycle of 35% max. 2. Measured with 22 µF cap within 150 mm of output terminal at 20 MHz bandwidth. 3. Measured at 200 V AC input & 100% load. CPL Efficiency(3) Typical 83% 79% Model Number CPL225PD24 CPL225PD12 Current Rating Maximum Peak(1) 5.0 A 9.0 A 14 A 5.0 A 10.0 A 20 A Regulation Line Load 20 mV 40 mV 96 mV 150 mV 20 mV 40 mV 48 mV 100 mV Ripple & Noise pk-pk(2) 120 mV 150 mV 120 mV 150 mV • Mechanical Details - 225 Watt Models I/O Connector CN1 CN2 B3P5-VH B8P-VH Mating Connector VHR-5N VHR-8N XHP-2 XHP-3 CN3 B2B-XH-A (Option) CN4 B3B-XH-A (Option) Terminal Chain: SVH-21T-P1.1 Loose: 8VH-21T-P1.1 Chain: SVH-21T-P1.1 Loose: 8VH-21T-P1.1 Chain: SXH-001-P0.6 Loose: BXH-001T-P0.6 Chain: SXH-001-P0.6 Loose: BXH-001T-P0.6 Pin No. 1 2 3 4 5 CN1 Input AC(L) AC(N) FG Pin No. 1, 2, 3 4, 5, 6 7, 8 9, 10 CN2 Output G2 V2 G1 V1 CN3 (Optional) CN4 (Optional) Pin No. ‘-Z’ Pin No. Remote On/Off NOTES: 1 + 1 RC(+) • Weight 700g or less (without chassis & cover). 2 COM • Tolerance ±1. 2 RC(-) • Dimensions in mm. 3 • PCB Material : CEM3. • Optional chassis & cover, order part no. CPL225 COVER or add suffix ‘-C’ to the model number to receive the unit with the cover fitted. • Mounting torque 1.5N m (16 kgf cm) max. • Keep drawing current per pin below 5 A (7 A @ pk load) for CN2. • Optional connector kit available, order part no. CPL225 CON. • Optional loom kit available, order part no. CPL225 LOOM. Derating Curves - 225 Watt Models OPEN FRAME COVER FITTED (>90 VAC INPUT) www.xpplc.com sales@xpplc.com Rev 3.0