ECP130PS12

ECP130 Series AC-DC Power Supplies XP Power 130 Watts • 100 W Convection/130 W Forced-cooled Ratings • 2” by 3” Footprint • Low 1.1” Profile • High Efficiency, up to 95% • Medical and ITE Approvals • High Power Density • Less than 0.5 W No Load Input Power • 3 Year Warranty The ECP130 series is designed to minimize the no load power consumption and maximize efficiency Dimensions: to facilitate equipment design to meet the latest environmental legislation. Approved for medical and ECP130: ITE applications, this range of single output AC-DC power supplies are packaged in a low profile 3.00 x 2.00 x 1.10” (76.2 x 50.8 x 28.0 mm) 1.1” height with a foot print of just 2” by 3”. The ECP130 provides up to 130 W force-cooled or | 100 W convection-cooled leading to very high power densities of 19.7 W/in3 or 15.1 W/in3 respectively. The power supply contains two fuses and low leakage currents as required by medical applications and is safety approved to operate in a 70 °C ambient. The low profile and safety approvals covering ITE and medical standards along with conducted emissions to EN55011/32 level B allow the versatile ECP130 series to be used in a vast range of applications. Models & Ratings Output Current Convection-cooled Forced-cooled(1) Output Power Output Voltage 130 W 12.0 V 8.33 A 130 W 15.0 V 6.66 A 130 W 18.0 V 130 W Efficiency(2) Model Number(3) 10.83 A 93% ECP130PS12 8.66 A 93% ECP130PS15 5.55 A 7.22 A 93% ECP130PS18 24.0 V 4.16 A 5.41 A 93% ECP130PS24 130 W 28.0 V 3.57 A 4.64 A 93% ECP130PS28 130 W 36.0 V 2.77 A 3.61 A 93% ECP130PS36 130 W 48.0 V 2.08 A 2.70 A 93% ECP130PS48 Notes 1. Requires 10 CFM. 2. Typical efficiency measured at full load and 230VAC input. 3. Add suffix ‘-S’ for input and output screw terminals e.g. ECP130PS24-S Summary Characteristic Input Range Minimum Typical Maximum Units Notes & Conditions 85 115/230 264 VAC Derate load from 100% at 90 VAC to 85% at 85 VAC 0.5 W % 230 VAC (see fig.1 & 2) +70 °C See derating curve (fig.3) No Load Input Power Efficiency 95 Operating Temperature Safety Approvals 1 -30 ITE IEC62368-1, UL62368-1, CSA 22.2 No.62368-1-11 Ed 2, EN62368-1, LVD Medical IEC60601-1 Ed 3.1 Including Risk Management, ANSI/AAMI ES60601-1 & CSA C22.2 No.6061-1:08, EN60601-1 www.xppower.com ECP130 Series AC-DC Power Supplies XP Power Input Characteristic Minimum Typical Maximum Units Notes & Conditions 85 115/230 264 VAC Derate output from 100% at 90 VAC to 85% at 85 VAC Input Frequency 47 50/60 63 Hz Power Factor 0.8 Input Voltage - Operating Input Current - Full Load Inrush Current Earth Leakage Current 1.3/0.65 A 115/230 VAC 120 A 230 VAC cold start, 25 ºC 115/230 VAC/50 Hz (Typ), 264 VAC/60 Hz (Max) 20/40 No load Input Power Input Protection Agency approval, 47-63 Hz 230 VAC, 100% load EN61000-3-2 class A 50 μA 0.5 W F3.15 A/250 V Internal fuse fitted in line and neutral. Output - Main Output Characteristic Minimum Output Voltage 12 Typical Initial Set Accuracy Maximum Units Notes & Conditions 48 VDC See Models and Ratings table ±1 % 50% load, 115/230 VAC % None Output Voltage Adjustment Minimum Load 0 Start Up Delay Hold Up Time 2 10 15/11 A No minimum load required s 115/230 VAC full load. ms Min at full load, 115 VAC. Typical at 100W/ 130W Drift ±0.02 % After 20 min warm up Line Regulation ±0.5 % 90-264 VAC Load Regulation ±0.5 % 0-100% load. Transient Response 4 % Recovery within 1% in less than 500 μs for a 50-75% and 75-50% load step Over/Undershoot 7 % Full load Ripple & Noise 1 % pk-pk Overvoltage Protection 110 140 % Overload Protection 110 170 % I nom 0.02 %/˚C Short Circuit Protection 95% (0 VAC), 8.3 ms EN55035 (100 VAC) EN55035 (240 VAC) Dips and Interruptions EN60601-1-2 (100 VAC) EN60601-1-2 (240 VAC) A Dip 30% (70 VAC), 416 ms A Dip >95% (0 VAC), 4160 ms Dip >95% (0 VAC), 10.0 ms B A Dip 30% (168 VAC), 500 ms A Dip >95% (0 VAC), 5000 ms B Dip 100% (0 VAC), 10.0 ms A Dip 100% (0 VAC), 20 ms A Dip 60% (40 VAC), 100 ms B Dip 30% (70 VAC), 500 ms A Dip 100% (0 VAC), 5000 ms B Dip 100% (0 VAC), 10.0 ms A Dip 100% (0 VAC), 20 ms A Dip 60% (96 VAC), 100 ms A Dip 30% ( 168 VAC), 500 ms A Dip 100% (0 VAC), 5000 ms B www.xppower.com Notes & Conditions Performance criteria A