HDS800PS12

AC-DC 800 Watts xppower.com HDS800 Series • High Efficiency up to 92% • 1U Profile, High Power Density • Programmable Output Voltage (0-105%) • Programmable Output Current (0-105%) • Parallel Operation • Fully Featured Signals & Controls • 3 Year Warranty Specification Input General Input Voltage • 90-264 VAC (127-370 VDC), see derating curve Input Frequency • 47-63 Hz Input Current • 9.3 A/3.7 A typical at 100/240 VAC Inrush Current • 30.0 A/60.0 A typical at 115/230 VAC Power Factor • 0.98/0.95, typical at 115/230 VAC full load Earth Leakage Current • 95% 10 ms, 30% 500 ms, >95% 5000 ms, Perf Criteria A, A, B UL62368-1, CSA C22.2 No 62368-1-14, EN 62368-1, IEC62368-1:2014, CE (Meets all applicable directives), UKCA (Meets all applicable legislation) Notes 1. Tolerance includes setup time tolerance, line regulation and load regulation Output Power Output Voltage V1 800 W 800 W 800 W 800 W 800 W 800 W 800 W 12.0 VDC 15.0 VDC 24.0 VDC 30.0 VDC 36.0 VDC 48.0 VDC 60.0 VDC Output Current Min Max 0.0 A 66.7 A 0.0 A 53.4 A 0.0 A 33.5 A 0.0 A 26.7 A 0.0 A 22.3 A 0.0 A 16.7 A 0.0 A 13.4 A Efficiency(2) Model Number 89% 90% 92% 92% 92% 92% 92% HDS800PS12 HDS800PS15 HDS800PS24 HDS800PS30 HDS800PS36 HDS800PS48 HDS800PS60 AC-DC HDS800 Models and Ratings Notes 1. Ripple & noise is measured with 20 MHz bandwidth and using 12”twisted pair-wire terminated with 0.1 μF & 47 μF capacitors in parallel. 2. Measured with 230 VAC input and full load. Mechanical Details 1 1.61 (40.9) 9.80 (249.0) +V M6 -V 2 1 3 x M4 (bottom side) Penetration Depth = 4mm Max Torque = 1.27 Nm 2.91 (74.0) Airflow 24 23 5.00 (127.0) TRIM STATUS LED CN2 E 2.52 (64.0) N L 0.55 (14.0) 7.80 (198.0) 1.46 (37.0) 0.81 (20.5) 1.06 (26.9) 6 x M4 (Both sides) 0.98 (25.0) Penetration Depth = 4mm Max Torque = 1.27 Nm 0.45 (11.5) 8.70 (221.0) Pin Functio Mating connector CN2: Manufacturer :JST Housing: PHDR-24VS Contacts: SPHD-002T-P0.5 (28-24 AWG) 1 Notes 1. All dimensions are in inches (mm). 2. Weight 3.85 lb (1.75 kg) 3. Maintain 2” (50mm) clear space at each end. *Only usable with driver board “KIT-RS232-X” or “KIT-RS485-1” 0.32 (8.0) CN2 Control Pin Connections Pin Function Description Description VS+ Remote sense (+) 9 EN- 2 VO+ 10 3 VS- 11 4 VO- Positive Output Voltage Remote Sense (-) Negative Output Voltage 12 AUX 5 POK Power OK 13 ACI 6 GND PAR 15 8 VSET Ground Parallel Operation Current Share Aux Output Setting 14 7 16 Pin Function Inhibit On/Off(-) 17 AUX GND Ground 18 GND Ground EN+ Inhibit On/Off (+) +5V/0.5 A or +9V/0.3 A Standby power 19 SCL I2C Serial Clock 20 SDA I2C Serial Data I Program 21 AUX GND Ground 22 GND +5V/0.5 A or +9V/0.3 A power Ground VCI V Program 23 RX* Receive GND Ground 24 TX* Transmit Derating Curve Thermal Derating Curve Input Derating Curve 100 100 90 80 Load (%) Load (%) 80 60 40 70 60 20 50 -10 0 10 20 30 40 50 60 70 40 Ambient Temperature (˚C) 90 Description +5V/0.5 A or +9V/0.3 A Standby power 100 110 120 Input Voltage (VAC) 264 LED Status LED Status Solid (Green) Solid (Orange) Slow Blink (Green) Slow Blink (Orange) Fast Blink (Red) Solid (Red) Slow Blink (Red) Intermittent Blink (Red) Short & Long Blink (Red) Output Status DC Output OK DC Output OK in remote control mode Output Not Enabled Output Not Enabled in remote control mode Over Voltage Over Loaded Over Temperature Fan Fail AUX Standby Failure Output Voltage Programming Via External Voltage 120 Via External Resistor 120 100 Output Voltage (%) Output Voltage (%) 100 80 60 40 80 60 40 20 20 0 0 0 1 2 3 4.5 4.8 5 4 0 1 2 3 4 4.5 4.8 Resistor Value (k Ω ) Programming Voltage (VDC) Output Current Program Via External Voltage 120 Via External Resistor 120 100 Output Current (%) 100 Output Current(%) AC-DC HDS800 Application Notes 80 60 40 80 60 40 20 20 0 0 0 1 2 3 4 4.5 5 0 1 2 3 4.5 4 Resistor Value (k Ω ) Programming Voltage (VDC) Remote Enable *GND shown in the diagram (below) is referring to the GND of CN2, not the Grounding from output power (V-) AUX AUX 2KΩ SW 2KΩ EN+ OFF Power OFF ON Power ON AUX AUX 2KΩ EN+ L H AUX EN- EN- GND GND OFF Power OFF ON Power ON EN+ SW Power OFF Power ON External DC source (Max = 9Vdc) AUX ENL/H (A) Using internal auxilliary standby GND GND (B) Using external transistor (C) Using external voltage source External Programming Voltage Connection IC=1mA IC=1mA IC=1mA I-sink min 1mA 220R CTRL VCI/ACI Power Supply + - A/D PWM CTRL VCI/ACI Power Supply VC = IC x R 0-5VDC CTRL VCI/ACI Power Supply R=0-5K 5 5 AC-DC HDS800 Application Notes OVP Setting POK Signal OVP Trip Point POWER SUPPLY AUX 200% 3300R 196% Pok Power not 1 120% 2 114% Power OK 1 2 100% 105% 7% GND % of Nominal Output Voltage CN2 Connector Open drain signal, low when PSU turns on Maximum sink current: 20 mA Maximum drain voltage: 40 V CN2 23 23 24 1 2 CN2 23 24 2 1 CN2 CN2 2 1 2 1 CN2 Remote Sense 23 24 23 24 Current Share 24 RX* TX* AUX GND SCL SDA 23 24 AUX GND VCI GND ACI GND 2 1 CN2 EN+ Load AUX EN- GND PAR VSET 23 POK GND VS- VO- VS+ VO+ 1 Load 24 23 24 23 24 23 24 RX* TX* RX* TX* RX* TX* RX* TX* AUX GND AUX GND AUX GND AUX GND SCL SDA SCL SDA SCL SDA SCL SDA AUX GND AUX GND AUX GND AUX GND 2 VCI GND VCI GND VCI GND VCI GND ACI GND ACI GND ACI GND ACI GND EN+ AUX EN+ AUX EN+ AUX EN+ AUX EN- GND EN- GND EN- GND EN- GND 1 2 PAR VSET PAR VSET PAR VSET PAR VSET POK GND POK GND POK GND POK GND VS- VO- VS- VO- VS- VO- VS- VO- VS+ VO+ VS+ VO+ VS+ VO+ VS+ VO+ 1 2 1 2 1 2 1 2 Local Sense CN2 TX* GND SDA AUX GND VCI GND ACI GND RX* TX* RX* TX* RX* TX* RX* TX* EN+ AUX AUX GND AUX GND AUX GND AUX GND EN- GND SCL SDA SCL SDA SCL SDA SCL SDA PAR VSET AUX GND AUX GND AUX GND AUX GND POK GND 2 SCL 23 24 Load Current Sharing with Remote Sensing 24 RX* AUX CN2 1 23 1 VS- VO- VS+ VO+ 23 2 Must be used if remote sense is not required. 1 24 23 24 23 24 23 24 VCI GND VCI GND VCI GND VCI GND ACI GND ACI GND ACI GND ACI GND EN+ AUX EN+ AUX EN+ AUX EN+ AUX EN- GND EN- GND EN- GND EN- GND PAR VSET PAR VSET PAR VSET PAR VSET POK GND POK GND POK GND POK GND VS- VO- VS- VO- VS- VO- VS- VO- VS+ VO+ VS+ VO+ VS+ VO+ VS+ VO+ 2 1 2 1 2 1 2 Current Sharing with Local Sensing Notes In parallel operation, it is possible that only one unit will operate if the load is less than 5% of the combined rated output load. It is possible to have more than five units in parallel, contact sales for details. *Pin 23 and 24, Only usable with driver board “KIT-RS232-X” or “KIT-RS485-1” 10 Nov 2022