IMM0205S05

IMM02 Series DC-DC Converter XP Power 2 Watts xxx Series • World Wide Medical Approvals • Single and Dual Outputs • SIP8 Package • -20 °C to +100 °C Operation • Full Load at 60 °C Ambient • 1500 VAC Isolation • 1 x MOPP at 250VAC • MTBF 1 MHrs • 3 Year Warranty Dimensions: IMM02: 0.86 x 0.36 x 0.44” (21.85 x 9.2 x 11.1 mm) Models & Ratings Input Voltage Output Voltage 4.5-9.0 V 9.0-18.0 V Input current Output Current No Load Full Load Maximum capacitive load Model Number 3V3 606 mA 75 mA 694 mA 2200 μF IMM0205S3V3 5V 400 mA 75 mA 626 mA 2200 μF IMM0205S05 12 V 167 mA 75 mA 617 mA 470 μF IMM0205S12 15 V 133 mA 75 mA 617 mA 470 μF IMM0205S15 ±3.3 V ±303 mA 55 mA 684 mA ±1000 μF IMM0205D03 ±5 V ±200 mA 55 mA 654 mA ±1000 μF IMM0205D05 ±12 V ±83 mA 75 mA 601 mA ±220 μF IMM0205D12 ±15 V ±66 mA 75 mA 601 mA ±220 μF IMM0205D15 3V3 606 mA 25 mA 317 mA 2200 μF IMM0212S3V3 5V 400 mA 25 mA 289 mA 2200 μF IMM0212S05 12 V 167 mA 25 mA 285 mA 470 μF IMM0212S12 15 V 133 mA 25 mA 289 mA 470 μF IMM0212S15 ±3.3 V ±303 mA 55 mA 317 mA ±1000 μF IMM0212D03 ±5 V ±200 mA 55 mA 292 mA ±1000 μF IMM0212D05 ±12 V ±83 mA 30 mA 285 mA ±220 μF IMM0212D12 ±15 V ±66 mA 30 mA 281 mA ±220 μF IMM0212D15 Notes Input currents measured at low input voltage. Mechanical Details Pin Connections 0.86 (21.85) 0.02 (0.50) 0.36 (9.20) Printed Face 0.42 (10.6) 0.12 (3.0) 0.44 (11.10) Bottom View 0.36 (9.20) 0.13 (3.20) 0.02 (0.50) 0.02 (0.50) Single -Vin +Vin Dual -Vin +Vin 3 Remote On/Off Remote On/Off 6 7 8 +Vout -Vout No Pin +Vout Common -Vout Notes 1. All dimensions are in inches (mm) 2. Weight: 0.009 lbs (4.2 g) approx. 3. Pin diameter: 0.02±0.002 (0.5±0.05) 4. Pin pitch tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) 0.10 (2.54) 0.70 (17.78) 1 0.01 (0.25) Pin 1 2 www.xppower.com IMM02 Series DC-DC Converter XP Power Input Characteristic Input Voltage Range Minimum Maximum Units Notes & Conditions 4.5 Typical 9 VDC 5 V nominal 9 18 VDC 12 V nominal 0.05 A2s 16 VDC for 100 ms 5 V models 25 VDC for 100 ms 12 V models Maximum Units Notes & Conditions 15 VDC See Models and Ratings table ±2 % Inrush Current Input Reflected Ripple Current 30 mA pk-pk Input Surge Through 12 μH inductor and 47 μF capacitor Output Characteristic Minimum Output Voltage 3.3 Typical Initial Set Accuracy Minimum Load 0 % Line Regulation ±0.5 % Load Regulation 2.0 % From 0% to full load On dual output models, when one output is at 25% load and other is varied from 10% load to full load Cross Regulation ±5 % Ripple & Noise 1 % pk-pk Short Circuit Protection Continuous fold-back mode, with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient Overload Protection Remote On/Off 20 MHz bandwidth. Measured using 0.1 μF ceramic capacitor 135 165 0.03 %/ ˚C 210 % Of nominal output current at nominal input voltage Output is on if remote on/off (pin 3) is open Output turns off if 2-4 mA is applied to remote on/off (pin 3) General Characteristic Efficiency Minimum Typical Maximum Units 64 78 79 % Isolation: Input to Output 1500 Switching Frequency 175 Isolation Resistance 109 1000 27 Power Density 14 1 Weight Typical value is for IMM0212S12 VAC At 250 VAC working voltage, 1 x MOPP kHz May enter burst mode frequency of 12-28 kHz at light load Ω Isolation Capacitance Mean Time Between Failure Notes & Conditions pF W/in3 MHrs 0.009 (4.2) MIL-HDBK-217F, +25 °C GB lb (g) Environmental Characteristic Maximum Units Operating Temperature -20 +100 °C Storage Temperature -40 +125 °C Case Temperature Humidity Minimum Typical +105 °C 95 %RH Cooling Notes & Conditions Derate from 100% load at +60 °C to 50% at +80 °C Non-condensing Natural convection www.xppower.com 2 IMM02 Series DC-DC Converter XP Power EMC: Emissions Phenomenon Standard Test Level Notes & Conditions Conducted EN55011 Class B See Application Note Radiated EN55011 Class B EMC: Immunity Phenomenon Standard Test Level Criteria ESD Immunity EN61000-4-2 ±15 kV A Notes & Conditions Radiated Immunity EN61000-4-3 10 Vrms A EFT/Burst EN61000-4-4 2 kV A External input filter required, see applications note Surge EN61000-4-5 2 kV A External input filter required, see applications note Conducted Immunity EN61000-4-6 10 V rms A Magnetic Fields EN61000-4-8 30 A/m A Air Discharge Safety Approvals Safety Agency Safety Standard Notes & Conditions UL ANSI/AMMI ES60601-1 CSA CSA C22.2 No. 60601-1 TUV EN60601-1 CB IEC60601-1 CE Meets all applicable directives UKCA Meets all applicable legislation Mechanical Details 0.86 (21.85) 0.02 (0.50) 0.36 (9.20) Printed Face 0.42 (10.6) 0.44 (11.10) 0.12 (3.0) Bottom View 0.36 (9.20) 0.13 (3.20) 0.01 (0.25) Pin Connections 0.02 (0.50) 0.02 (0.50) 0.10 (2.54) Pin 1 2 Single -Vin +Vin Dual -Vin +Vin 3 Remote On/Off Remote On/Off 6 7 8 +Vout -Vout No Pin +Vout Common -Vout 0.70 (17.78) Notes 1. All dimensions are in inches (mm) 2. Weight: 0.009 lbs (4.2 g) approx. 3. Pin diameter: 0.02±0.002 (0.5±0.05) 4. Pin pitch tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) Application Note External Filter for Surge and EFT EMI Filter Conducted Emissions + Vout + Vout L1 + Vin C1 D1 IMM02 -Vin C1 Load C2 C3 IMM02 -Vin -Vout C1 is 220 µF, 100 V electrolytic capacitor D1 is 18 V, 3 kW TVS for 5 V input or 28 V, 3 kW TV5 for 12 V input 3 + Vin Load -Vout C2 & C3 are 10 µF, 35 V multilayer ceramic chip capacitors, placed as close as possible to the input pins L1 is 12 µH inductor C1 is 200 µF, 100 V Electrolytic Capacitor for 5 V input version only www.xppower.com 23 Sept 2021